Sn58Bi Solder Alloys Research Articles

Investigation of the mechanical properties of lead-free Sn-58Bi solder alloy with cobalt addition through flux doping

PurposeThis study aims to investigate the effect of incorporating cobalt (Co) into Sn-58Bi alloy on its phase composition, tensile properties, hardness and thermal aging performances. The fracture morphologies of tensile-tested solders are also investigated to correlate the microstructural changes with tensile properties of the solder alloys. Then, the thermal aging performances of the solder alloys are investigated in terms of their intermetallic compound (IMC) layer morphology and thickness.Design/methodology/approachThe Sn-58Bi and Sn-58Bi-xCo, where x = 1.0, 1.5 and 2.0 Wt.%, were prepared using the flux doping technique. X-ray diffraction (XRD) is used to study the phase composition of the solder alloys, whereas scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) are used to investigate the microstructure, fractography and compositions of the solders. Tensile properties such as ultimate tensile strength (UTS), Young’s modulus and elongation are tested using the tensile test, whereas the microhardness value is gained from the micro-Vickers hardness test. The morphology and thickness of the IMC layer at the solder’s joints are investigated by varying the thermally aging duration up to 56 days at 80°C.FindingsXRD analysis shows the presence of Co3Sn2 phase and confirms that Co was successfully incorporated via the flux doping technique. The microstructure of all Sn-58Bi-xCo solders did not differ significantly from Sn-58Bi solders. Sn-58Bi-2.0Co solder exhibited optimum properties among all compositions, with the highest UTS (87.89 ± 2.55 MPa) at 0.01 s−1 strain rate and the lowest IMC layer thickness at the interface after being thermally aged for 56 days (3.84 ± 0.67 µm).Originality/valueThe originality and value of this research lie in its novel exploration of the flux doping technique to introduce minor alloying of Co into Sn-58Bi solder alloys, providing new insights into enhancing the properties and performance of these solders. This new Sn-Bi-Co alloy has the potential to replace lead-containing solder alloy in low-temperature soldering.

Effect of electromigration on microstructure and properties of CeO2 nanopartical-reinforced Sn58Bi/Cu solder joints

To mitigate the decrease in mechanical performance of Sn58Bi/Cu solder joints resulting from electromigration-induced damage. The CeO2 nanoparticles were incorporated into Sn58Bi solder by a melt-casting method, and their effects on the microstructure and properties of Sn58Bi/Cu solder joints under electromigration were investigated. The study results demonstrate that the addition of 0.125 ~ 0.5 wt% CeO2 nanoparticles refines the eutectic microstructure of Sn58Bi solder alloy. At an addition amount of 0.5 wt%, the composite solder alloy exhibits the maximum tensile strength of 68.9 MPa, which is 37% higher than that of the base solder. CeO2 nanoparticle-reinforced Sn58Bi solder can achieve excellent solderbility with Cu substrates and the joints can significantly inhibit the growth of the anodic Bi-rich layer, which is responsible for electromigration. With the extension of current stressing time, Bi-rich and Sn-rich layer are respectively formed on the anode and cathode in the joints. The intermetallic compound (IMC) layer grows asymmetrically, transitioning from a fan-shaped morphology to a flattened structure at the anode and to a thickened mountain-like morphology at the cathode. Adding the CeO2 nanoparticles helps to mitigate the decrease in mechanical performance caused by electromigration damage during current application to some extent. Over the current stressing period of 288 ~ 480 h, the fracture position shifts from the anodic IMC/Bi-rich interface to the cathodic Sn-rich/IMC interface. The fracture mechanism transitions from a brittle fracture characterized by plate-like cleavage to a ductile–brittle mixed fracture with fine dimples and cleavage.

Investigation on the Thermal and Wettability Properties Aided with Mechanical Test Simulation of Tin (Sn) - Bismuth (Bi) Solder Alloy at Low Reflow Temperatures

The current study proposes to investigate the thermal, wettability and mechanical properties of a low temperature SnBi solder. The main aim is to investigate the performance of the SnBi solder alloy with different Bi composition. The study also establishes the relationship between melting temperature, spreading area and tensile stress of the SnBi with different Bi composition at different low reflow temperatures. The thermal and wettability tests are conducted experimentally, while the mechanical test will be analysed via finite element analyses (FEA). The single shear lap test method was adopted for the simulation. The thermal properties of the SnBi solder are investigated using the differential scanning calorimeter (DSC). The reflow temperature selected ranges from 160 °C to 220 °C to accommodate the purpose of low temperature soldering. Wetting test results showed that spreading area of Sn48Bi solder alloy increased to 28.1 and 42.88 at 180 °C and 210 °C respectively. The increase in the Bi composition reduced the tensile strength regardless of the increase of the reflow temperature. The preliminary results commend the characteristics of the SnBi solder as a possible alternative to the Pb solder.

Research Overview on the Electromigration Reliability of SnBi Solder Alloy.

Due to the continuous miniaturization and high current-carrying demands in the field of integrated circuits, as well as the desire to save space and improve computational capabilities, there is a constant drive to reduce the size of integrated circuits. However, highly integrated circuits also bring about challenges such as high current density and excessive Joule heating, leading to a series of reliability issues caused by electromigration. Therefore, the service reliability of integrated circuits has always been a concern. Sn-based solders are widely recognized in the industry due to their availability, minimal technical issues during operation, and good compatibility with traditional solders. However, solders that are mostly Sn-based, such as SAC305 and SnZn, have a high melting point for sophisticated electronic circuits. When Bi is added, the melting point of the solder decreases but may also lead to problems related to electromigration reliability. This article reviews the general principles of electromigration in SnBi solder joints on Cu substrates with current flow, as well as the phenomena of whisker formation, voids/cracks, phase separation, and resistance increase caused by atomic migration due to electromigration. Furthermore, it explores methods to enhance the reliability of solder joint by additives including Fe, Ni, Ag, Zn, Co, RA (rare earth element), GNSs (graphene nanosheets), FNS (Fullerene) and Al2O3. Additionally, modifying the crystal orientation within the solder joint or introducing stress to the joint can also improve its reliability to some extent without changing the composition conditions. The corresponding mechanisms of reliability enhancement are also compared and discussed among the literature.

Preparation and soldering performance of SAC305@Sn-bi Core-shell solder balls based on eutectic co-deposition

SnBi eutectic thin film alloys are widely used in microelectronic devices, sensors, biomedical devices due to their high resistance, low temperature coefficient, chemical stability, and biocompatibility. However, the large standard electrode potential difference (454 mV) between Sn (−0.136 V) and Bi (+0.3118 V) makes them difficult to be co-deposited, especially with eutectic composition. In this study, cathodic polarization curves were used to analyze the negative shift of the cathodic reduction potentials of Sn and Bi induced by gelatin and EDTA-2Na, respectively, which reduced the potential difference between the two to 184 mv (Sn:-0.958 v; Bi:-0.774 v) and enabled the co-deposition of Sn and Bi; cathodic overpotentials were analysed to show that catechol not only improves the degree of cathodic polarization, but also raises the overpotentials, resulting in flatter surface coatings; By adjusting the temperature, current density, and pulse current, a SnBi eutectic thin film coating with good weldability, controllable thickness, flat surface, density, and uniformity was obtained on copper foil using a platinum as the anode in a methanesulfonic acid solution. The results indicate that it is feasible to deposit SnBi solder alloy at eutectic points (Sn41.53Bi58.47, At.%). Under the synergistic effect of gelatin and unidirectional square wave pulse, a typical eutectic network morphology can be obtained, which is the same as the microstructure of industrial SnBi eutectic solder. Based on these, a core-shell composite soldering material for low-temperature soldering was obtained by using SAC305 solder balls as cores and a SnBi low-temperature soldering material coating was roll-plated on their surfaces. This study provides a reliable technical way and theoretical guidance for low-temperature soldering, preparation of low-temperature solderable core-shell composite soldering material, and application of sensors and optoelectronic devices.

Mechanical Response of Cu/Sn58Bi-xNi/Cu Micro Solder Joint with High Temperatures

Sn58Bi solder is considered a promising lead-free solder that meets the performance requirements, with the advantages of good wettability and low cost. However, the low melting point characteristic of Sn58Bi poses a serious threat to the high-temperature reliability of electronic products. In this study, Sn58Bi solder alloy based on nickel (Ni) functionalization was successfully synthesized, and the effect of a small amount of Ni on creep properties and hardness of Cu/Sn58Bi/Cu micro solder joints at different temperatures (25 °C, 50 °C, 75 °C, 100 °C) was investigated using a nanoindentation method. The results indicate that the nanoindentation depth of micro solder joints exhibits a non-monotonic trend with increasing Ni content at different temperatures, and the slope of the indentation stage curve decreases at 100 °C, showing that the micro solder joints undergo high levels of softening. According to the observation of indentation morphology, Ni doping can reduce the indentation area and accumulation around the indentation, especially at 75 °C and 100 °C. In addition, due to the severe creep phenomenon at 100 °C, the indentation hardness rapidly decreases. The indentation hardness values of micro solder joints of Cu/Sn58Bi/Cu, Cu/Sn58Bi-0.1Ni/Cu, and Cu/Sn58Bi-0.2Ni/Cu at 100 °C are 14.67 ± 2.00 MPa, 21.05 ± 2.00 MPa, and 20.13 ± 2.10 MPa, respectively. Nevertheless, under the same temperature test conditions, the addition of Ni elements can improve the high-temperature creep resistance and hardness of Cu/Sn58Bi/Cu micro solder joints.

A Review of Recent Research Trends of Forming of Metallic Bondlines Using Core-Shell Particles and Bonding Properties According to Particle Type

With the increasing numbers of electric vehicles and the prevalence of high heat generating devices, recent studies have attempted to address the limitations of conventional solder materials, including their low durability at temperatures exceeding 200 ℃, insufficient mechanical properties in a joint, and low thermal conductivity. Transient liquid-phase (TLP) partial bonding using solders or Sn, and sinter bonding using Ag particles, are alternative bonding methods which involve a modification or change of the material. Advanced alternatives can significantly reduce bonding time or material cost. Various additional studies have investigated various core-cell particles that can be used to form an all-metallic bondline. This review summarizes reports of bonding studies using different core-cell particles. The particles were not only applied as a form of paste but also preform. In the TLP bonding using X(Cu, Ag, Ni)@Sn particles, the degree of voids generated in the formed bondline was dependent on the type of intermetallic compound formed. The preforms consisting of X@Sn particles provided relatively uniform microstructure and void distribution, compared to the pastes containing identical X@Sn particles, resulting in better long-term mechanical reliability. The addition of Zn@Sn particles contributed to the more practical control of microstructure and mechanical properties in the joint formed by pure Sn and Sn-58Bi solder alloys. Cu@Ag particles can be considered a promising low-cost material for compression-assisted sinter bonding, replacing pure Ag particles. The application of core-cell particles is expected to improve the processes used for forming metallic bondlines.

Coupled effect of Ag and In addition on the microstructure and mechanical properties of Sn–Bi lead-free solder alloy

The microstructure and mechanical properties of Sn–Bi solder alloys with various Ag and In addition are comparatively investigated. The results illustrate that the tensile strength and ductility of the solder alloy could be dramatically enhanced with negligible loss of the plasticity. Especially, the Sn–Bi solder alloy with 0.4 wt. % Ag and 1.5 wt. % In exhibits the maximum tensile strength and elongation of 79.7 MPa and 45.9%, respectively. The microstructure of the Sn–Bi solder alloys is mainly composed of Bi-rich and β-Sn phases. With the addition of elements Ag and In, the microstructure is significantly refined, and the lamellar eutectic structure with thinner interlayer spacing could be detected. Element Ag tends to form Ag3Sn phase while element In solutes in the Sn matrix. The mechanical properties of the as-prepared Sn–Bi solder alloy are improved attributed to the precipitated-phase strengthening of the fined Ag3Sn phase and the refinement effect of In on coarse Bi-rich phase.

Effect of Sb and Ag additions on the melting and solidification of Sn-Bi solder alloys

Effect of Sb and Ag additions on the melting and solidification of Sn-Bi solder alloys

Finite Element Analysis of Sn-58Bi Shear Test

Finite element analysis (FEA) of quasi-static single lap shear test was conducted to study the mechanical properties of Sn-58Bi in terms of deformation, strain, stress, yield strength and ultimate strength. The study generated results of simulated behaviour of low temperature Sn-Bi solder alloy to address the demand of low temperature solder alloys in the electronic industry. The geometry was constructed in SolidWorks based on ASTM D1002 standard before being imported to ANSYS. The simulation was conducted at shear velocity of 0.1, 0.5, 1 and 1.27 mm/min and temperature of 138, 178, 208 and 238 °C using ANSYS. The simulation results were compared with the corresponding experimental results. Simulation results showed that an increase in shear velocity caused a decrease in ultimate strength and an increase in ductility of Sn-58Bi. As the velocity increased from 0.5 to 1.27 mm/min, the ultimate strength decreased from 339.87 to 291.24 MPa. This is predicted due to the Bi-rich layer within the lamellar structure of Sn-Bi alloy. An increase in temperature caused an increase in ultimate strength and brittleness in Sn-58Bi due to the trans-granular propagation of brittle failures along the weak Bi-abundant phase. As the temperature increased from 138 to 238°C, ultimate strength increased from 290.46 to 298.93 MPa.

Effect of multi-walled carbon nanotubes on the microstructure and properties of Sn-58Bi solder alloys

The influence of multi-walled carbon nanotube (MWCNT) content on the melting properties, wettability, microstructure, and intermetallic compounds (IMCs) of Sn-58Bi-xMWCNT (x = 0, 0.01, 0.02, 0.03, 0.05, and 0.10 wt.%) and the effects of MWCNT on the tensile strength of Cu/Sn-58Bi-xMWCNT/Cu solder joint were analyzed. The results show that MWCNT addition at a small trace amount into Sn-58Bi solder could increase the spreading area of Sn-58Bi solder, refine the solder matrix microstructure, inhibit the growth of interfacial IMCs, and significantly improve the tensile strength of Sn-58Bi solder joints. However, the melting point and melting range remained the same or slightly changed. The wettability of Sn-58Bi alloys increased first and then decreased with the addition of MWCNT. The spreading area and the tensile strength of solder joint were the maximum when the MWCNT content was 0.01 wt.%, and they were 42.23 mm2 and 50.07 MPa, respectively. The reason may be related to the improved microstructure of solder alloys and the morphology of IMCs due to MWCNT addition at trace level.

Effect of Ni-modified reduced graphene oxide on the mechanical properties of Sn–58Bi solder joints

Sn–58Bi solder has great research value as a low-temperature solder. However, it still requires strengthening due to a lot of brittle Bi-phase, which reduces mechanical reliability. In this study, Ni-modified reduced graphene oxide (rGO@Ni) was prepared by heat reduction, and mechanical stirring was used to manufacture rGO@Ni-reinforced Sn–58Bi composite solder. The distribution, phase composition, and structural changes of graphene and Ni nanoparticles during enhancer synthesis were characterized in detail by Scanning Electron Microscope, Energy Dispersive Spectroscopy Raman and Fourier Transform Infrared spectra, X-ray Photoelectron Spectroscopy, X-ray Diffraction, and Transmission Electron Microscope. Besides, the morphology of intermetallic compound (IMC) layers of the composite solder/Cu interface was investigated. The thickness of the IMC layer decreases with the increase of rGO@Ni content. The microstructure analysis demonstrated that the rGO@Ni distributed near the IMC layer, which limits the diffusion of metal atoms and decreases the IMC layer's growth rate during the reflowing process. Besides, compared with Sn–58Bi solder alloys, the addition of 0.01 wt% rGO@Ni can increase the shear strength by up to 15%. However, when the content of rGO@Ni is more than 0.05 wt%, it agglomerates inside the composite solder, resulting in a decrease in the shear strength of the composite solder joint.

Effects of alloying element on mechanical properties of Sn-Bi solder alloys: a review

PurposeThis paper aims to review recent reports on mechanical properties of Sn-Bi and Sn-Bi-X solders (where X is an additional alloying element), in terms of the tensile properties, hardness and shear strength. Then, the effects of alloying in Sn-Bi solder are compared in terms of the discussed mechanical properties. The fracture morphologies of tensile shear tested solders are also reviewed to correlate the microstructural changes with mechanical properties of Sn-Bi-X solder alloys.Design/methodology/approachA brief introduction on Sn-Bi solder and reasons to enhance the mechanical properties of Sn-Bi solder. The latest reports on Sn-Bi and Sn-Bi-X solders are combined in the form of tables and figures for each section. The presented data are discussed by comparing the testing method, technical setup, specimen dimension and alloying element weight percentage, which affect the mechanical properties of Sn-Bi solder.FindingsThe addition of alloying elements could enhance the tensile properties, hardness and/or shear strength of Sn-Bi solder for low-temperature solder application. Different weight percentage alloying elements affect differently on Sn-Bi solder mechanical properties.Originality/valueThis paper provides a compilation of latest report on tensile properties, hardness, shear strength and deformation of Sn-Bi and Sn-Bi-X solders and the latest trends and in-depth understanding of the effect of alloying elements in Sn-Bi solder mechanical properties.

The Effects of Temperature and Solute Diffusion on Volume Change in Sn-Bi Solder Alloys

The different rates of thermal expansion of the many materials that make up an electronic assembly combined with temperature fluctuations are the driver of the thermal fatigue failure of solder joints. A characteristic of the Sn-Bi system, which provided the basis for many of the low process temperature solder alloys that the electronics industry is now adopting, is the very temperature-sensitive solubility of Bi and Sn in the other phase. In this study, in situ synchrotron powder x-ray diffraction was used to characterize the temperature dependence of the lattice parameters of the βSn and Bi phases in Sn-57wt%Bi and Sn-37wt%Bi. The effects of temperature and solute were separated by comparing with the data from pure βSn and pure Bi and verified using density functional theory calculations. Furthermore, the coefficients of thermal expansion of βSn and Bi during heating were also derived to reveal the thermal expansion behavior.

Microstructural Evolution and Mechanical Properties of Sn‐58Bi Solder Alloys with Different Cooling

Herein, influences of air‐cooling, water‐cooling, and liquid nitrogen‐cooling (LN‐cooling) on microstructures and mechanical properties of Sn–58Bi alloy are studied. It is observed that nearly complete eutectic structures are obtained in air‐cooled Sn–58Bi alloy. Fine grains and many low‐angle grain boundaries (LAGBs) are obtained in water‐cooled Sn–58Bi alloy. The LN‐cooling method causes Bi atoms to form large, regular rectangular shapes, and there are many high‐angle grain boundaries (HAGBs) distributed inside the specimen. Impact tests are performed at room temperature. When the impact rate is 0.98 m s−1, the fracture energy of the water‐cooled Sn–58Bi alloy peaks to 71.5 mJ. The fracture of the LN‐cooled impact specimen has a large cleavage step due to the interaction of cleavage cracks and the HAGBs. These experimental results lay the relevant theoretical foundation for the practical application of Sn–58Bi solder alloys.

Study on the Reliability of Sn–Bi Composite Solder Pastes with Thermosetting Epoxy under Thermal Cycling and Humidity Treatment

In this study, a Sn–Bi composite solder paste with thermosetting epoxy (TSEP Sn–Bi) was prepared by mixing Sn–Bi solder powder, flux, and epoxy system. The melting characteristics of the Sn–Bi solder alloy and the curing reaction of the epoxy system were measured by differential scanning calorimeter (DSC). A reflow profile was optimized based on the Sn–Bi reflow profile, and the Organic Solderability Preservative (OSP) Cu pad mounted 0603 chip resistor was chosen to reflow soldering and to prepare samples of the corresponding joint. The high temperature and humidity reliability of the solder joints at 85 °C/85% RH (Relative Humidity) for 1000 h and the thermal cycle reliability of the solder joints from −40 °C to 125 °C for 1000 cycles were investigated. Compared to the Sn–Bi solder joint, the TSEP Sn–Bi solder joints had increased reliability. The microstructure observation shows that the epoxy resin curing process did not affect the transformation of the microstructure. The shear force of the TSEP Sn–Bi solder joints after 1000 cycles of thermal cycling test was 1.23–1.35 times higher than the Sn–Bi solder joint and after 1000 h of temperature and humidity tests was 1.14–1.27 times higher than the Sn–Bi solder joint. The fracture analysis indicated that the cured cover layer could still have a mechanical reinforcement to the TSEP Sn–Bi solder joints after these reliability tests.

Local solidification thermal parameters affecting the eutectic extent in Sn-Cu and Sn-Bi solder alloys

PurposeOverall, selection maps about the extent of the eutectic growth projects the solidification velocities leading to given microstructures. This is because of limitations of most of the set of results when obtained for single thermal gradients within the experimental spectrum. In these cases, associations only with the solidification velocity could give the false impression that reaching a given velocity would be enough to reproduce a result. However, that velocity must necessarily be accompanied by a specific thermal gradient during transient solidification. Therefore, the purpose of this paper is to not only project velocity but also include the gradients acting for each velocity.Design/methodology/approachCompilation of solidification velocity, v, thermal gradient, G, and cooling rate, Ṫ, data for Sn-Cu and Sn-Bi solder alloys of interest is presented. These data are placed in the form of coupled growth zones according to the correlated microstructures in the literature. In addition, results generated in this work for Sn-(0.5, 0.7, 2.0, 2.8)% Cu and Sn-(34, 52, 58)% Bi alloys solidified under non-stationary conditions are added.FindingsWhen analyzing the cooling rate (Ṫ = G.v) and velocity separately, in or around the eutectic composition, a consensus cannot be reached on the resulting microstructure. The (v vs. G) + cooling rate diagrams allow comprehensive analyzes of the combined v and G effects on the subsequent microstructure of the Sn-Cu and Sn-Bi alloys.Originality/valueThe present paper is devoted to the establishment of (v vs. G) + cooling rate diagrams. These plots may allow comprehensive analyses of the combined v and G effects on the subsequent microstructure of the Sn-Cu and Sn-Bi alloys. This microstructure-processing mapping approach is promising to predict phase competition and resulting microstructures in soldering of Sn-Cu and Sn-Bi alloys. These two classes of alloys are of interest to the soldering industry, whereas manipulation of their microstructures is considered of utmost importance for the metallurgical quality of the product.

A SnBiAgIn solder alloy with exceptional mechanical properties by rapid quenching

As a widely adopted candidate in the modern electric industry, much attention has been paid to SnBi solder alloy. However, the intrinsic brittleness of this alloy hinders its further application. To tackle this challenge, a SnBiAgIn solder alloy with lower melting temperature but outstanding mechanical properties was prepared in this work. The ultimate tensile strength and elongation stand at 104.2 MPa and 52.3%, respectively, displaying an exceptional trade-off between strength and ductility as well as a higher creep resistance. The addition of Ag facilitates the formation of intermetallic compounds (IMCs) and refinement of solidification structure while the alloying of In induces the solid solution softening effect, which can enhance the strength and ductility simultaneously. Compared with SnBi eutectic solder alloy, dislocation climb and glide become the dominant creep mechanism. The IMCs distributed in the SnBiAgIn solder alloy matrix can act as the obstacles to hinder the movement of dislocations and subsequently produce higher creep resistance.

Low Melting Temperature Sn-Bi Solder: Effect of Alloying and Nanoparticle Addition on the Microstructural, Thermal, Interfacial Bonding, and Mechanical Characteristics

Sn-based lead-free solders such as Sn-Ag-Cu, Sn-Cu, and Sn-Bi have been used extensively for a long time in the electronic packaging field. Recently, low-temperature Sn-Bi solder alloys attract much attention from industries for flexible printed circuit board (FPCB) applications. Low melting temperatures of Sn-Bi solders avoid warpage wherein printed circuit board and electronic parts deform or deviate from the initial state due to their thermal mismatch during soldering. However, the addition of alloying elements and nanoparticles Sn-Bi solders improves the melting temperature, wettability, microstructure, and mechanical properties. Improving the brittleness of the eutectic Sn-58wt%Bi solder alloy by grain refinement of the Bi-phase becomes a hot topic. In this paper, literature studies about melting temperature, microstructure, inter-metallic thickness, and mechanical properties of Sn-Bi solder alloys upon alloying and nanoparticle addition are reviewed.

Influence of Sb2O3 Nanoparticles Addition on the Thermal, Microstructural and Creep Properties of Hypoeutectic Sn–Bi Solder Alloy

Here we investigate the effects (thermal, microstructural, and creep properties) of adding Sb2O3 nanoparticles to a hypoeutectic Sn-5 wt% Bi solder alloy. The Sb2O3-containing solder alloy was prepared by mechanically incorporating 0.5 wt% Sb2O3 nanoparticles into the Sn-5 wt% Bi solder alloy. The addition of nano-sized Sb2O3 particles to the Sn–Bi solder alloy increases the melting temperature, but only slightly. The main phases of the investigated solder alloys include the β-Sn and Bi-rich phases in addition to the crystalline phase of Sb2O3 nanoparticles. No other intermetallic compounds were observed in the β-Sn matrix. The tensile creep experiments have been carried out in the 303–363 K temperature interval under constant stresses ranging from 5.1 to 7.64 MPa. The creep parameters of both solders increased gradually with increasing creep temperature up to 333 K, after which they increased rapidly with relatively higher values. The creep parameters of the Sb2O3-containing solder alloys are smaller than that of Sb2O3-free solder alloys. The present solder alloys exhibit class-M creep behavior. The calculated stress exponent values and activation energy data for both solders could be related to dislocation climb through core diffusion as the dominant operating mechanism.