Small Amount Research Articles

Hong Kong popular music education and its (dis)contents

This article presents some of the data gathered in a study on popular music education in Hong Kong, which was marginalized in local schools until recently. The study was conducted between April and December 2021 to explore possible policies that could promote Hong Kong popular music via education. It adopted a mixed-method design that consisted of a survey questionnaire, ten in-depth, semi-structured interviews with popular music education stakeholders and fifteen focus-group interviews with participants in various popular music education programmes. While the research findings are based on a small amount of data about a short period, from them I hope to offer a modest suggestion on how to draft policies that promote Hong Kong popular music, a genre that is generally agreed to be declining in the new millennium, through education in the future.

NO2 gas response and recovery properties of ambipolar CNT-FETs with various CNT/CNT junctions

Gas sensors based on ambipolar carbon nanotube (CNT) field-effect transistors with various amounts of CNTs were fabricated by dielectrophoretic assembly. The nitrogen dioxide (NO2) gas response and recovery properties of the transistors were measured to investigate the effect of CNT amount on gas response. For the device with a small amount of CNTs, responses from the CNT bulk and CNT/electrode contacts were observed. For devices with a large amount of CNTs, in which a network-like structure of CNTs was observed near the electrodes, an increased current in both electron and hole conduction regions was observed compared with that for the device with a small amount of CNTs. The increased current in the electron conduction region rapidly decreased during recovery. This response is consistent with that of CNT/CNT X-type contacts, which have a high resistance before NO2 adsorption. Equivalent circuits of CNT channels with CNT/CNT contacts were developed, allowing the transistor behavior to be qualitatively discussed. Evaluation of time constants revealed that CNT/electrode contacts and CNT/CNT X-type contacts exhibited high NO2 adsorption and desorption rates, respectively.

Low blood concentration of alcohol enhances activity related to stopping failure in the right inferior frontal cortex.

This study investigated the effects of low doses of alcohol, which are acceptable for driving a car, on inhibitory control and neural processing using the stop-signal task (SST) in 17 healthy right-handed social drinkers. The study employed simultaneous functional magnetic resonance imaging and electromyography (EMG) recordings to assess behavioral and neural responses under conditions of low-dose alcohol (breath-alcohol concentration of 0.15mg/L) and placebo. The results demonstrated that even a small amount of alcohol consumption prolonged Go reaction times in the SST and modified stopping behavior, as evidenced by a decrease in the frequency and magnitude of partial response EMG that did not result in button pressing during successful inhibitory control. Furthermore, alcohol intake enhanced neural activity during failed inhibitory responses in the right inferior frontal cortex, suggesting its potential role in behavioral adaptation following stop-signal failure. These findings suggest that even low levels of alcohol consumption within legal driving limits can greatly impact both the cognitive performance and brain activity involved in inhibiting responses. This research provides important evidence on the neurobehavioral effects of low-dose alcohol consumption, with implications for understanding the biological basis of impaired motor control and decision-making and potentially informing legal guidelines on alcohol consumption.

Data Communication for Low Resources IoT Devices: RS485 Over Electrical Wires

The Internet of Things is a paradigm that has been widely deployed in various areas, connecting commonly used devices, from home to industry and health, among others. IoT devices generally have a small amount of memory, low processing resources, and it is often required that they have low energy consumption. Therefore, one objective of this research is to try to take advantage of a classic cable communications standard, RS485, so as to allow the connection of simple devices to the TCP/IP network through an intermediary node. Thus, the IoT device would only require an asynchronous serial port and an interface to the electrical network. To that end, data transmission tests have been carried out over interfaces based on the THVD8000 integrated circuit. The achieved results encourage to continue working on this issue.

Inhibition of HSP90AA1 induces abnormalities in bovine oocyte maturation and embryonic development.

HSP90AA1 is a ubiquitous molecular chaperone that can resist cellular stress, such as oxidative stress and apoptosis, and mediate the efficacy and protein folding of normal cells during heat stress, as well as many other functions. This study further reveals the role of HSP90AA1 in bovine oocyte maturation and early embryonic development. HSP90AA1, a highly abundant and ubiquitous molecular chaperone, plays important roles in various cellular processes including cell cycle control, cell survival, and hormone signaling pathways. In this study, we investigated the functions of HSP90AA1 in bovine oocyte and early embryo development. We found that HSP90AA1 was expressed at all stages of development, but was mainly located in the cytoplasm, with a small amount distributed in the nucleus. We then evaluated the effect of HSP90AA1 on the in vitro maturation of bovine oocytes using tanespimycin (17-AAG), a highly selective inhibitor of HSP90AA1. The results showed that inhibition of HSP90AA1 decreased nuclear and cytoplasmic maturation of oocytes, disrupted spindle assembly and chromosome distribution, significantly increased acetylation levels of α-tubulin in oocytes and affected epigenetic modifications (H3K27me3 and H3K27ac). In addition, H3K9me3 was increased at various stages during early embryo development. Finally, the impact of HSP90AA1 on early embryo development was explored. The results showed that inhibition of HSP90AA1 reduced the cleavage and blastocyst formation rates, while increasing the fragmentation rate and decreasing blastocyst quality. In conclusion, HSP90AA1 plays a crucial role in bovine oocyte maturation as well as early embryo development.

Engineering Detrimental Functional Groups in Conductive Additives Toward High-Performance All-Solid-State Batteries.

Conductive additives are of great importance for the adequate utilization of active materials in all-solid-state lithium batteries by establishing conductive networks in the composite cathode. However, it usually causes severe interfacial side reactions with solid electrolytes, especially sulfide electrolytes, leading to sluggish ion transportation and accelerated performance degradation. Herein, a simple hydrogen thermal reduction process is proposed on a commonly used conductive additive Super P, which effectively removes the surface oxygen functional groups and weakens the interfacial side reactions with sulfide. With a small amount of 1 wt % reduced Super P, ASSLBs demonstrates a competitive capacity of 180.2 mAh g-1 , which is much higher than the 130.8 mAh g-1 of untreated Super P. Impressively, reduced Super P based ASSLBs also exhibit a higher capacity retention of 81.8 % than 64.6 % of untreated Super P. The cathode interfacial chemical evolutions reveal that reduced Super P could effectively alleviate the side reactions of sulfide. Reduced Super P shows better reversible capacity compared to reduced carbon nanofiber with almost no loss of capacity retention, due to its more complete conductive network. Our results highlight the importance of oxygen-containing functional groups for conductive additives, lightening the prospect of low-cost 0D conductive additives for practical ASSLBs.

The Clinical Teaching Fellow role: exploring expectations and experiences

BackgroundMany UK junior doctors are now taking a year out of the traditional training pathway, usually before specialty training, and some choose to work as a clinical teaching fellow (CTF). CTFs primarily have responsibility for delivering hospital-based teaching to undergraduate medical students. Only a very small amount of literature is available regarding CTF posts, none of which has explored why doctors choose to undertake the role and their expectations of the job. This study aimed to explore the expectations and experiences of CTFs employed at NHS hospital Trusts in the West Midlands.MethodsCTFs working in Trusts in the West Midlands region registered as students on the Education for Healthcare Professionals Post Graduate Certificate course at the University of Birmingham in August 2019 took part in a survey and a focus group.ResultsTwenty-eight CTFs participated in the survey and ten participated in the focus group. In the survey, participants reported choosing a CTF role due to an interest in teaching, wanting time out of training, and being unsure of which specialty to choose. Expectations for the year in post were directly related to reasons for choosing the role with participants expecting to develop teaching skills, and have a break from usual clinical work and rotations. The focus group identified five main themes relating to experiences starting their job, time pressures and challenges faced in post, how CTF jobs differed between Trusts, and future career plans. Broadly, participants reported enjoying their year in a post at a mid-year point but identified particular challenges such as difficulties in starting the role and facing time pressures in their day-to-day work.ConclusionThis study has provided a valuable insight into the CTF role and why doctors choose a CTF post and some of the challenges experienced, adding to the sparse amount of literature. Understanding post holders’ experiences may contribute to optimisation of the role. Those employing CTFs should consider ensuring a formal handover process is in place between outgoing and incoming CTFs, having a lead person at their Trust responsible for evaluating changes suggested by CTFs, and the balance of contractual duties and personal development time.

Harnessing of carboxy containing starch nanoparticles as an adsorbent for Cd (II) ions and methylene blue from waste water effluent: synthesis, metrological characterization and properties

Purpose The novelty addressed here is undertaken by using tailor-made and fully characterized starch nanoparticles (SNPs) having a particle size ranging from 80 to 100 nm with a larger surface area, biodegradability and high reactivity as a starting substrate for cadmium ions and basic dye removal from wastewater effluent. This was done via carboxylation of SNPs with citric acid via esterification reaction using the dry preparation technique, in which a simple, energy-safe and sustainable process concerning a small amount of water, energy and toxic chemicals was used. The obtained adsorbent is designated as cross-linked esterified starch nanoparticles (CESNPs). Design/methodology/approach The batch technique was used to determine the CESNPs adsorption capacity, whereas atomic adsorption spectrometry was used to determine the residual cadmium ions concentration in the filtrate before and after adsorption. Different factors affecting adsorption were examined concerning pH, contact time, adsorbent dose and degree of carboxylation. Besides, to validate the esterification reaction and existence of carboxylic groups in the adsorbent, CESNPs were characterized metrologically via analytical tools for carboxyl content estimation and instrumental tools using Fourier-transform infrared spectroscopy (FTIR) spectra and scanning electron microscopy (SEM) morphological analysis. Findings The overall adsorption potential of CESNPs was found to be 136 mg/g when a 0.1 g adsorbent dose having 190.8 meq/100 g sample carboxyl content at pH 5 for 60 min contact time was used. Besides, increasing the degree of carboxylation of the CESNPs expressed as carboxyl content would lead to the higher adsorption capacity of cadmium ions. FTIR spectroscopy analysis elucidates the esterification reaction with the appearance of a new intense peak C=O ester at 1,700 cm−1, whereas SEM observations reveal some atomic/molecules disorder after esterification. Originality/value The innovation addressed here is undertaken by studying the consequence of altering the extent of carboxylation reaction expressed as carboxyl contents on the prepared CESNPs via a simple dry technique with a small amount of water, energy and toxic chemicals that were used as a sustainable bio nano polymer for cadmium ions and basic dye removal from wastewater effluent in comparison with other counterparts published in the literature.

Pilonidal Sinus of the Anal Canal: A Rare Entity - Case Report

AbstractPilonidal sinus is the term first used by Hodges in 1880 to describe a granulomatous lesion containing hairs. It has been previously described as hair extracted from an ulcer and referred to as Jeep's disease, in world war days. Pilonidal sinus is the condition in which a sinus or fistula is situated at a short distance from the anus and generally contains hairs. It is commonly observed in the sacrococcygeal region and a few other sites, such as the axilla, umbilicus, face, etc. Its presence elsewhere is uncommon. Predisposing factors are traumatized, hairy skin, which leads entry of the hair inside the wound, thus forming a sinus. A 31-year-old patient presented with discharging endoanal sinus tract, which, on exploration, turned out to be an endoanal pilonidal sinus containing hair tufts, a rare case. The patient complained of recurrent pus discharge and anal pain for 45 days, reporting history of travelling around 70 km daily in a two-wheeler vehicle.On first physical evaluation, a small endoanal bulge was found. It was located at 1 o'clock in lithotomy position (anterior), with purulent discharge and anterior anal fissure. For confirmation, an endoanal ultrasonography (USG) was performed, which showed a sinus tract containing internal echoes and gas bubbles with a small amount of pus. The sinus was explored, and a wide excision was made and left open for secondary healing.Pilonidal sinus of the anal canal is a rare entity, and it can be found in hairy patients who are used to going on long, daily rides on two wheeled vehicles.

Enhancement of mechanical properties and oxidation resistance of TiAl alloy with addition of Nb and Mo alloying elements

In this study, small button-shaped ingots were prepared by a non-self-consuming vacuum arc melting method. The effect of the content of Nb and Mo elements on the microstructure, mechanical properties and oxidation resistance of TiAl alloys were investigated. The as-cast TiAl alloy presented laminar microstructure. When only adding Nb element, a small amount of β phase was distributed in the form of dots at the grain boundaries of α2/γ lamellar structure. When adding both Mo and Nb, the precipitated β phase started to precipitate in lines inside the α2/γ lamellar structure. The microhardness of the alloy increased with the increasing Nb and Mo content. The compressive strength of the alloys increased firstly with the increasing Nb content and decreased when the content of Nb exceeded 7 wt%. However, with the addition of Mo, the compressive strength of the alloys decreased drastically. The optimal compressive strength of the alloy, i.e. 2250 MPa, was obtained with 5 wt% Nb and 5 wt% Mo addition. The oxidation resistance of the alloys were enhanced with the addition of Nb and Mo elements and the TiAl–5Nb–5Mo alloy also showed the best oxidation resistance at 800 °C.

First Report of Agroathelia rolfsii Causing Southern Blight on Cowpea in China

Cowpea (Vigna unguiculata L.) is a legume consumed as a high-quality plant protein source in many parts of the world. In August 2023, it was observed that a plant disease affected cowpea growth in Yiyang (28.34°N, 112.55°E), China. The average disease incidence was 10%, resulting in 8.5% economic losses in approximately 3,000 m2. The symptoms initially appeared as brown lesions near the stem-soil interface and the lesions were colonized by white mycelia. As the disease progressed, the disease symptoms included constriction and brown staining at the base of the stem, covered with a small amount of white mycelia. Eventually, the entire plants withered and collapsed and many sclerotia were scattered on the ground around the diseased stem. Twenty samples (10 sclerotia and 10 diseased tissue fragments) were collected from symptomatic plants for causal agent isolation. Samples were disinfected with 70% ethanol for 30 s, 5% NaClO for 1 min, rinsed three times with sterile water, dried and placed on potato dextrose agar (PDA) plates at 28℃ in the dark. In total, 20 isolates were obtained by the hyphal tip method (Terrones et al. 2022) and showed a consistent phenotype of white cottony mycelia on PDA with an growth rate of 12.9 to 21.3 mm/day (n = 20). Sclerotia formed at five to eight days post inoculation, were initially whitish, turning beige and eventually dark brown. The diameter of mature sclerotia ranged from 0.89 to 2.13 mm (mean = 1.64±0.29 mm; n =50). For pathogen identification, ITS1/ITS4 (White et al. 1990) and EF1-983F/EF1-2218R (Rehner and Buckley 2005) primers were used to amplify the internal transcribed spacer regions (ITS) and translation elongation factor-1 alpha gene (TEF-1α), respectively. The sequences of all 20 isolates showed 99% to 100% similarity with Agroathelia rolfsii sequences from GenBank by BLAST analysis. The sequences of two representative strains, ID1 and ID4, were deposited in GenBank. The ITS sequences of ID1 (OR689482) and ID4 (OR689481) were ＞99% similar to A. rolfsii strain QJ7 (593/596 bp; MZ750983) and A. rolfsii strain Kale078 (565/568 bp; MN872304), respectively. Also, TEF-1α sequences of ID1 (OR713735) and ID4 (OR713736) were ＞99% similar to the sequences of A. rolfsii strain HS-Sr (1073/1073 bp; OL416131) and A. rolfsii strain MSB1-2 (1070/1075 bp; MN702790), respectively. Phylogenetic analysis based on ITS and TEF1-α sequences indicated that ID1 and ID4 clustered into the A. rolfsii clade. Based on morphology and sequence analyses, the isolates ID1 and ID4 were identified as A. rolfsii (anamorph Sclerotium rolfsii). Pathogenicity tests were conducted three times on healthy 30-day-old cowpea seedlings. Five plants were inoculated with 6-day-old mycelial discs (6 mm) of ID1 or ID4 at the base of the seedlings (n = 30) while four plants were inoculated with a sterile PDA disc as a control (n = 12). All seedlings were cultivated in a greenhouse with a temperature of 26°C to 28°C and relative humidity 60% to 80% with a 14/10 h light/dark photoperiod. Eight days later, all the fungal inoculated seedlings showed symptoms including brown necrosis and collapse of the stems, and eventual withering of the seedlings. Control plants remained asymptomatic. The causal pathogens were reisolated in PDA plates and identified by ITS sequence analysis, completing Koch's postulates. To our knowledge, this is the first report of A. rolfsii causing southern blight on cowpea in China. Early accurate diagnosis will help farmers to adopt suitable practices to control disease outbreaks and reduce losses.

User Identification Across Multiple Social Networks Based on Naive Bayes Model.

Recently, the problem of user identification across multiple social networks (UIAMSNs) has attracted considerable attention since it is a prerequisite for many downstream tasks and applications. Although substantial network feature-based approaches have been proposed to solve the UIAMSNs' problem, the matching degree in most of the current works is given by experience, which lacks a solid theoretical basis. To alleviate the above predicament, we propose a user identification algorithm based on naive Bayes model (UI-NBM) within the network feature-based framework. First, a matching degree index is designed based on the naive Bayes model, which can accurately measure the contributions of different common matched node pairs (MNPs) to the connection probability of unmatched node pairs (UMNPs). Second, the matching degrees of all UMNPs are formulated as the product of matrices, giving rise to the great reduction of the time complexity and the compact expression; Finally, with the idea of recursion process, more UMNPs can be iteratively predicted even when only a small amount of prior information (i.e., a few number of MNPs) is known. The experimental results on the synthetic and real cross platforms demonstrate that the method outperforms the baseline methods within the feature-based framework.

CO2 hydrogenation to synthetic natural gas with light hydrocarbons on Mn-promoted mesoporous Co3O4-Al2O3 metal oxides

Direct CO2 conversion into synthetic natural gas (SNG, CH4) with simultaneous small production of light paraffinic C2-C4 hydrocarbons to enhance a heating value of SNG was investigated with ordered mesoporous CoMnAl mixed metal oxides (denoted as m-CoMnAl). CO2 hydrogenation activity to form hydrocarbons with small CO byproduct formed by a reverse water gas shift reaction (RWGS) was strongly affected by the MnO2 promoter content in the ordered Co3O4-Al2O3 mesoporous structures. The m-CoMnAl structures with proper amount of Mn promoter were found to be effective to enhance CO2 conversion to methane with small amount of light hydrocarbons formation, which were mainly attributed to the presence of abundant oxygen vacant sites with a stable preservation of the partially oxidized cobalt nanoparticles in the ordered mesoporous Co3O4-Al2O3 structures even under a reductive hydrogenation condition. Selective methanation of CO2 was found to be more favorable on the highly reduced metallic cobalt nanoparticles formed with smaller amount of Mn promoter (m-CoMnAl(0.05)), however, excessive Mn content such as Mn/Co ratio > 1 (m-CoMnAl(1.0)) revealed less structural stability of ordered mesoporous structures with lower CO2 conversion with relatively higher CO selectivity of 1.4 % with lower olefin selectivity through severe phase segregations of the Co-Mn-Al mixed metal oxides with selective formations of MnCO3 phases.

Effects of nano-metal oxide additives on ignition and combustion properties of MICs-boron rich fuels

Boron has been considered a promising powdered metal fuel for enhancing composite propellants' energy output due to its high energy density. However, the high ignition temperature and low combustion efficiency limit the application of boron powder due to the high boiling point of the boron oxide layer. Much research is ongoing to overcome these shortcomings, and one potential approach is to introduce a small quantity of metal oxide additives to promote the reaction of boron. This study prepared boron-rich fuels with 10 wt% of eight nano-metal oxide additives by mechanical ball milling. The effect of metal oxides on the thermo-oxidation, ignition, and combustion properties of boron powder was comprehensively studied by the thermogravimetric analysis (TG), the electrically heated filament setup (T-jump), and the laser-induced combustion experiments. TG experiments at 5 K/min found that Bi2O3, MoO3, TiO2, Fe2O3, and CuO can promote thermo-oxidation of boron. Compared to pure boron, Tonset can be reduced from 569 °C to a minimum of 449 °C (B/Bi2O3). Infrared temperature measurement in T-jump tests showed that when heated by an electric heating wire at rates from 1000 K/s to 25000 K/s, the ignition temperatures of B/Bi2O3 are the lowest, even lower than the melting point of boron oxide. Ignition images and SEM for the products further showed that the high heating rate is beneficial to the rapid reaction of boron powder in the single-particle combustion state. Fuels (B/Bi2O3, B/MoO3, and B/CuO) were mixed with the oxidant AP and ignited by laser to study the combustion performance. The results showed that B/CuO/AP has the largest flame area, the highest BO2 characteristic spectral intensity, and the largest burn rate for powder lines. To combine the advantages of CuO and Bi2O3, binary metal oxide (CBO, mass ratio of 3:1) was prepared and the test results showed that CBO can very well improve both ignition and combustion properties of boron. Especially B/CBO/AP has the highest burn rate compared with all fuels containing other additives. It was found that multi-component metal-oxide additive can more synergistically improve the reaction characteristics of boron powder than unary additive. These findings contribute to the development of boron-rich fuels and their application in propellants.

Tool Wear Monitoring System Using Seq2Seq

The advancement of smart factories has brought about small quantity batch production. In multi-variety production, both materials and processing methods change constantly, resulting in irregular changes in the progression of tool wear, which is often affected by processing methods. This leads to changes in the timing of tool replacement, and failure to correctly determine this timing may result in substantial damage and financial loss. In this study, we sought to address the issue of incorrect timing for tool replacement by using a Seq2Seq model to predict tool wear. We also trained LSTM and GRU models to compare performance by using R2, mean absolute error (MAE), and mean squared error (MSE). The Seq2Seq model outperformed LSTM and GRU with an R2 of approximately 0.03~0.037 in step drill data, 0.540.57 in top metal data, and 0.16~0.45 in low metal data. Confirming that Seq2Seq exhibited the best performance, we established a real-time monitoring system to verify the prediction results obtained using the Seq2Seq model. It is anticipated that this monitoring system will help prevent accidents in advance.

High-Sodium-Concentration Sodium Oxythioborosilicate Glass Synthesized via Ambient Pressure Method with Sodium Polysulfides.

The practical utilization of all-solid-state sodium batteries necessitates the development of a mass synthesis process for high-alkali-content sulfide glass electrolytes, which are characterized by both high ionic conductivity and remarkable formability. Typically, vacuum sealing and quenching are conventional techniques employed during the manufacturing process. In this paper, we present a novel approach, a pioneering method for the production of sulfide glass electrolytes with high alkali concentrations, achieved through ambient-pressure heat treatment and a gradual cooling process. We enhance the glass-forming ability of Na3BS3 by incorporating a small quantity of SiO2. The ionic conductivity of the resulting Na3BS3·0.225SiO2 (molar ratio) glass exhibited 1.5 × 10-5 S cm-1 at 25 °C, surpassing that of Na3BS3 glass. An all-solid-state cell utilizing Na3BS3·0.225SiO2 glass is successfully operated as a secondary battery at 60 °C. Our findings suggest that sodium oxythioborosilicate glass with electrochemical properties identical to those of Na3BS3 can be prepared without the need for quenching. These results propel the advancement of research in the domain of mass production processes tailored for high-alkali-content sulfide glass.

Supramolecular polymer-based gel fracturing fluid with a double network applied in ultra-deep hydraulic fracturing

A gel based on polyacrylamide, exhibiting delayed crosslinking characteristics, emerges as the preferred solution for mitigating degradation under conditions of high temperature and extended shear in ultralong wellbores. High viscosity/viscoelasticity of the fracturing fluid was required to maintain excellent proppant suspension properties before gelling. Taking into account both the cost and the potential damage to reservoirs, polymers with lower concentrations and molecular weights are generally preferred. In this work, the supramolecular action was integrated into the polymer, resulting in significant increases in the viscosity and viscoelasticity of the synthesized supramolecular polymer system. The double network gel, which is formed by the combination of the supramolecular polymer system and a small quantity of Zr-crosslinker, effectively resists temperature while minimizing permeability damage to the reservoir. The results indicate that the supramolecular polymer system with a molecular weight of (268–380) × 104 g/mol can achieve the same viscosity and viscoelasticity at 0.4 wt% due to the supramolecular interaction between polymers, compared to the 0.6 wt% traditional polymer (hydrolyzed polyacrylamide, molecular weight of 1078 × 104 g/mol). The supramolecular polymer system possessed excellent proppant suspension properties with a 0.55 cm/min sedimentation rate at 0.4 wt%, whereas the 0.6 wt% traditional polymer had a rate of 0.57 cm/min. In comparison to the traditional gel with a Zr-crosslinker concentration of 0.6 wt% and an elastic modulus of 7.77 Pa, the double network gel with a higher elastic modulus (9.00 Pa) could be formed only at 0.1 wt% Zr-crosslinker, which greatly reduced the amount of residue of the fluid after gel-breaking. The viscosity of the double network gel was 66 mPa s after 2 h shearing, whereas the traditional gel only reached 27 mPa s.

One-step synthesizing Ti3C2Tx doped with slight amount of Ni2+ to enhance the electrochemical stability

Two-dimensional layered material of Ti3C2Tx has attracted widespread attention due to its high conductivity, rich surface functional groups and excellent hydrophilicity. However, its practical application is hindered by the problems of re-stacking and the instability rooted from easy oxidation of low valent Ti. Here, a simple synthesis strategy that the surface of Ti3C2Tx is decorated by Ni2+ has been developed: a small amount of Ni2+ is added into the Ti3C2Tx dispersion to bind to the surface vacancies to obtain Ti3C2Tx-Ni during the ultrasonic stripping process. Therefore, the interlayer spacing of Ti3C2Tx-Ni-2 is expanded from 1.12 nm (for Ti3C2Tx) to 1.22 nm, meaning that the stacking and aggregation effect has been alleviated. Compared with the short storage time of Ti3C2Tx, the suspension of Ti3C2Tx-Ni-2 can keep stability for more than 270 days. The self-supporting Ti3C2Tx-Ni-2 film exhibits a specific capacitance of 208.0 F g−1 in 1.0 M H2SO4 and 82.8 F g−1 in 1.0 M Na2SO4 electrolyte at a scan rate of 2 mV s−1. Furthermore, it can still maintain 100 % of the initial capacitance after 10,000 cycles at a current density of 5 A g−1 in neutral electrolyte, while the Ti3C2Tx film can only retain 74.8 % of its initial capacitance.

FINANCIAL SATISFACTION DETERMINANTS FROM HOME INDUSTRY IN SURABAYA

<p><strong>Background</strong>:<em> </em>Financial satisfaction is one of the goals that every entrepreneur wants to achieve, which requires sacrifice of resources such as capital, time, energy, and other things to obtain it. Financial satisfaction is also the goal of a home business which is currently growing rapidly in Indonesia..</p><p><strong>Purpose</strong>: The purpose of this research is to examine the effect of income, financial literacy, financial attitudes, and financial distress on the financial satisfaction of home-based business owners in the city of Surabaya.</p><p><strong>Method</strong>: The convenience sampling method will be used to get 100 home-based business respondents in the city of Surabaya, both businesses that were established before or during the COVID-19 pandemic. Data collection was carried out by distributing questionnaires and the data was processed using SPSS software.</p><p><strong>Results</strong>: The results of this study indicate that only income and financial attitudes have a positive and significant effect on financial satisfaction, while financial literacy and financial distress do not affect financial satisfaction.</p><p><strong>Research Novelty</strong>: This research is a small amount of research that focuses on the achievements of home-based businesses that are thought to have the ability to survive during a pandemic. The findings prove that financial difficulties are not able to reduce their financial satisfaction.</p>

New insight into the taxonomy of Cephaloziellaceae (Marchantiophyta): the family of the smallest higher plants on Earth.

An analysis of the phylogeny of Cephaloziellaceae was carried out based on trees constructed for previously and newly obtained sequences of five genes: nuclear ITS1-2 and chloroplast trnL-F, trnG, rbcL, and psbA. Phylogenetic trees inferred from different genes are congruent for the main details; however, the position of several taxa is variable. As a result, a new phylogenetic system of the family was proposed. The narrow genus concept seems to be more appropriate for the family. Cephaloziella spinicaulis is segregated into the new genus Douiniella, the generic status for Prionolobus and Metacephalozia is confirmed, and the dubious generic status of Kymatocalyx is substantiated. The generic independence of Cylindrocolea from Cephaloziella s. str. is confirmed. The small amount of data hinders the description of two more genera from Cephaloziella s.l.