Single Wire Research Articles

Parallel Wire Approach for Recanalisation of Chronic Total Coronary Occlusions in a Large Contemporary Multi-Center Registry.

The parallel wire technique (PW) is a classic part of the antegrade strategy to open chronic total coronary occlusions (CTO). With modern wires and dual-lumen catheters (DLC) the approach has evolved, but this progress had not been evaluated in a contemporary registry of CTO interventions. This analysis is based on 26,589 CTO procedures performed by 36 operators with > 50 procedures annually between 2015 and 2022. The different strategies and techniques were analyzed with respect to clinical and lesion characteristics, procedural resource use and periprocedural complications. Within the antegrade approach, PW was compared to antegrade wire escalation (AWE) and antegrade-dissection re-entry (ADR). The primary antegrade approach was used in 65.9%, primary retrograde in 16.9% and a strategy change in 17.2% with a wide inter-operator variability. In primary antegrade approach, PW was applied in 10.8% and ADR in 5.3%. Lesion complexity was higher in AWE and PW than with single wire, and highest in ADR procedures, leading to more complex procedures with higher contrast and radiation usage. Complications increased with ADR, while they were similar with PW and AWE. Through the observation period PW adoption increased steadily from 6.7% to 10.7%, as the DLC use facilitating PW increased from 8.3% to 17.0% over the observation period. In this largest database of contemporary CTO PCI from Europe, PW adoption increased over time but remained low at about 10%. While there was a wide individual variety among the operators, it was a safe and successful technique.

Modeling and Construction of Underwater Single Wire Power Transfer System

Modeling and Construction of Underwater Single Wire Power Transfer System

Discussion on effect of observation circumstances for image in digital radiography

The discriminability of the IQI in the film radiography is affected by the observation circumstance and the luminance of film viewer. ISO17636-2 states that the images of digital radiograph shall be examined in a dimmed room. However, it does not describe requirements for the observation environment in digital radiography, despite the fact that the environment is similar to that of a normal professional PC and the display of the images can be easily adjusted. In this report, the influence of the observation environment in digital radiography was compared as the parameters the wire diameter and the WL value of a display adjustment value when the minimum wire diameter of the image quality indicator (IQI) was percepted, using images of welded steel at t25mm and t50mm. For welded steel of t25mm, differences due to SNRN values and differences due to the observation environment of light and dark room were compared. For t50mm, differences due to the presence or absence of the observation mask for the single wire of wire IQI which is places in front of the display, differences due to the resolution and brightness of the PC monitor, and differences when the WL was adjusted arbitrarily or fixed were compared. For the Digital Radiographic testing (RT-D), the basic spatial resolutions (SRb) were obtained by measuring the profile and applying of visual observation with the duplex wire type IQI. On the other hand, when observing the image of wire type IQI, the observation ways that one was obtain the perceptible image for all wires and another was to get the perceptible single wire image by using the observation mask for watching each wire were applied. Moreover, the influence of window width (WW) and window level (WL) adjustment on the discrimination of wire-type IQI was examined by quantifying it as WW/WL. As a result, it was confirmed that the discriminality in the dimmed room and the adjustment of WW and WL were effective. In addition, using the observation a mask showed that the perception of the adjacent wire image affected observer cognition in IQI discrimination during image observation. When using viewer software profiling, SRb measurements were not affected by the observation environment, but the visual observation was affected by the environment, and when observing images in the dimmed room with RT-D, it was found that adjusting WW and WL had a greater effect on discrimination for images with low SNRN and low contrast.

Features of 2D mapping technique of non-uniform magnetic fields using self-biased magnetoelectric composites based on “bidomain LiNbO3/Ni/Metglas” structures

Magnetoelectric (ME) composites are extensively researched for their ability to detect magnetic fields but are typically characterized by their interactions with homogeneous magnetic fields. However, practical applications often involve non-uniform magnetic fields (NMFs). In this study, we developed and validated a technique for 2D mapping of NMFs using sensor based on ME composite. The primary focus was on mapping the magnetic field generated by a single wire carrying an alternating current (AC). The experimental setup included a “bidomain LiNbO3/Ni/Metglas” ME structure, which demonstrated a ME coefficient of 0.83 V/(cm⋅Oe) without external biasing at 117 Hz. The ME structure was characterized using both quasi-static and dynamic methods, with the mapping performed at a frequency of 232 Hz, chosen to ensure a linear response and minimize resonance effects. Our measurements revealed that the position of maximum magnitude of the ME signal was consistently shifted from the position of the maximum integral magnetic field intensity of the wire. This shift was attributed to the deformation of the ME structure and the redistribution of the magnetic flux along the sample due to the magnetic layers, as confirmed through modeling. Further, the measured 2D mapping of the NMF from the wire closely matched the theoretical distribution, displaying axial symmetry but with a persistent shift of 2–3 mm along the length of the ME structure. These effects were linked to the linear dimensions and clamping methods of the ME structure. Overall, our experimental results closely correlated with theoretical data and the FEM model, demonstrating that ME composites are effective for NMF detection and mapping. Future work will aim to reduce the dimensions of the ME structure using MEMS technology to minimize the observed shift effects in the measurements.

Dissimilar Resistance Welding of NiTi Microwires for High-Performance SMA Bundle Actuators

Shape memory alloys (SMAs) are becoming a more important factor in actuation technology. Due to their unique features, they have the potential to save weight and installation space as well as reduce energy consumption. The system integration of the generally small-diameter NiTi wires is an important cornerstone for the emerging technology. Crimping, a common method for the mechanical and electrical connection of SMA wires, has several drawbacks when it comes to miniaturization and high-force outputs. For high-force applications, for example, multiple SMA wires in parallel are needed to keep actuation frequencies high while scaling up the actuation force. To meet these challenges, the proposed study deals with the development of a resistance-welding process for manufacturing NiTi wire bundles. The wires are welded to a sheet metal substrate, resulting in promising functional properties and high joint strengths. The welding process benefits from low costs, easy-to-control parameters and good automation potential. A method for evaluating the resistance-welding process parameters is presented. With these parameters in place, a manufacturing process for bundled wire actuators is discussed and implemented. The welded joints are examined by peel tests, microscopy and fatigue experiments. The performance of the manufactured bundle actuators is demonstrated by comparison to a single wire with the same accumulated cross-sectional area.

Membandingkan Kekuatan Pengelasan Single Dan Double Kawat Inti Elektroda (Filler Rod) Menggunakan Las Smaw

Advances in welding technology are very helpful in making, repairing or repairing chassis jobs that have a high level of difficulty and requirements. Especially in the chassis, many welding elements are involved because welded joints have an important role to support the body, engine, and vehicle load. In practical work at CV. Pringgandani Welding Analysis Comparing the Strength of Welding Results of Single Electrode Core Wire and Double Electrode Core Wire (Filler Rod) Using SMAW welding which is carried out for chassis welding which is claimed by mechanics in welding with a depth and width of more than 5 mm, it is better to use double electrode core wire which can speed up and strengthen the weld. Then a test is carried out to prove the results of the Single Wire Electrode Core and Double Electrode Core Wire (Filler Rod) welds which are stronger and faster in the process. By testing the weld results on an iron plate with dimensions of 250 mm x 50 mm x 10 mm, the welding process uses the SMAW (Shielded Metal Arc Welding) welding method. Using an E6013 type electrode with a diameter of 2 mm with a current of 90 A, polarity DCEP (Direct Current Electrode Positive) The welding position used is the 1G position or horizontal position with the welding process using a single v-groove bevel butt joint and an angle of 60o with a weld width of 10 mm and a weld depth of 8 mm. The plate samples used were two samples. In sample 1 using a single wire core electrode, and sample 2 using a double wire core electrode. All samples were made of tensile test specimens with the ASME-IX standard, a tensile test was carried out to determine and prove the respective strengths of the welding results of Single Wire Core Electrode and Double Wire Core Electrode (Filler Rod).

Dissimilar joining of Ti–6Al–4V to 316L stainless steel by a novel joining process based on arc additive manufacturing and combined twin-wire arc welding

The joining structure of Ti–6Al–4V to 316L stainless steel has potential demands in many fields. However, it is very difficult to avoid the formaiton of intermetallic compounds (IMCs) of the weld between Ti–6Al–4V to 316L stainless steel, which will severely decrease joint properties. In this paper, a novel joining technology that combines the single wire backing arc welding and the spatially arranged combined twin-wire arc welding was utilized to join Ti–6Al–4V and 316L stainless steel. Copper alloy wire (S214) and vanadium alloy wire (V01) were used as filler metals to produce two isolation layers, which prevented the formation of IMCs. The phase compositions at the Fe/Cu, Cu/V and V/Ti interfaces were Fe(S,S) + Cu(S,S), Cu(S,S) + V(S,S) and V(S,S)+(β-Ti, V)SS respectively. The distribution of the spherical and clustered V(S,S) particles in the matrix at the Cu/V interface contributes to dispersion strengthening and solid solution strengthening of the interface. Tensile strength of 394 MPa with an elongation of 2.53% was achieved. The joint fractured at the Cu/V interface of the single wire backing arc weld and the Cu zone of the spatially arranged combined twin-wire arc weld respectively. Dimple plastic fracture modes were detected in the joints. This technology is not only applicable to Ti–6Al–4V titanium alloy/316L stainless steel dissimilar metal joining, but also provides a new research strategy for the joining between other dissimilar metals.

Wiring Covalent Organic Frameworks with Conducting Polymers.

Covalent organic frameworks are a class of crystalline porous polymers formed by linking organic units into periodically aligned skeletons and pores. Here we report a strategy for wiring these frameworks with conducting polymers via wall engineering and polymerization. We anchored each edge site with one pyrrole unit, which is densely packed along the z direction yet protruded from pore walls. This assembly enables the polymerization of pyrrole units to form polypyrrole and creates a new polypyrrole chain conformation. The resultant framework constitutes six single file polypyrrole chains in each pore and develop spatially segregated yet built-in single molecular wires with exceptional stable polarons. Hall effect measurements revealed that the materials are p-type semiconductors, increase conductivity by eight orders of magnitude compared to the pristine frameworks, and achieve a carrier mobility as large as 13.2 cm2 V-1 s-1. Our results open an avenue to π electronic frameworks by interlayer molecular wiring with conducting polymers.

Wiring Covalent Organic Frameworks with Conducting Polymers

AbstractCovalent organic frameworks are a class of crystalline porous polymers formed by linking organic units into periodically aligned skeletons and pores. Here we report a strategy for wiring these frameworks with conducting polymers via wall engineering and polymerization. We anchored each edge site with one pyrrole unit, which is densely packed along the z direction yet protruded from pore walls. This assembly enables the polymerization of pyrrole units to form polypyrrole and creates a new polypyrrole chain conformation. The resultant framework constitutes six single file polypyrrole chains in each pore and develop spatially segregated yet built‐in single molecular wires with exceptional stable polarons. Hall effect measurements revealed that the materials are p‐type semiconductors, increase conductivity by eight orders of magnitude compared to the pristine frameworks, and achieve a carrier mobility as large as 13.2 cm2 V−1 s−1. Our results open an avenue to π electronic frameworks by interlayer molecular wiring with conducting polymers.

Combined Threshold Implementation

Physical security is an important aspect of devices for which an adversary can manipulate the physical execution environment. Recently, more and more attention has been directed towards a security model that combines the capabilities of passive and active physical attacks, i.e., an adversary that performs fault-injection and side-channel analysis at the same time. Implementing countermeasures against such a powerful adversary is not only costly but also requires the skillful combination of masking and redundancy to counteract all reciprocal effects.In this work, we propose a new methodology to generate combined-secure circuits. We show how to transform Threshold Implementation (TI)-like constructions to resist any adversary with the capability to tamper with internal gates and probe internal wires. For the resulting protection scheme, we can prove the combined security in a well-established theoretical security model.Since the transformation preserves the advantages of TI-like structures, the resulting circuits prove to be more efficient in the number of required bits of randomness (up to 100%), the latency in clock cycles (up to 40%), and even the area for pipelined designs (up to 40%) than the state of the art for an adversary restricted to manipulating a single gate and probing a single wire.

Neuromorphic alternating current sensing using piezoelectric resonators and physical reservoir computing

Non-contact current sensors are valuable because they can safely measure alternating current without interrupting the circuit. However, current sensors utilizing Hall elements or coils are only available for single wires, and piezoelectric resonator-based sensors have difficulty achieving both high sensitivity and linearity. To address this issue, we propose a novel approach, that is, the use of piezoelectric current sensors as nodes for physical reservoir computing (physical RC), allowing us to utilize nonlinear regions. To improve the sensitivity and short-term memory required by physical RC, a piezoelectric resonator with a quality factor of 75 was realized by employing a tuning fork structure. Nonlinearities were also introduced by analog circuits. The results of the benchmark tests indicate that the device worked as a physical RC and that it successfully predicted unknown current values from the results of training at three levels of current.

A novel method for investigating the underwater explosion loads and bubble evolution

This paper presents an innovative experimental method for studying the evolution and energy output characteristics of underwater explosion bubbles. We independently constructed an experimental testing system for underwater electrical wire explosions (UEWE), in which electrodes connected to a metal wire serve as the load, and underwater explosions are initiated through instantaneous high-voltage discharge. By varying the diameter of the metal wire and configuring parallel wire arrays, we analyzed and discussed the explosion characteristic parameters and the current–voltage (I–V) signals under different conditions. The maximum bubble radius of the underwater metal wire explosion was compared with the corresponding equivalent explosive simulation results, and a numerical model for underwater metal wire explosion equivalent to explosive detonation was established. Subsequently, we discussed the characteristics of bubble generation and evolution under various conditions, clarifying the similarities and differences between wire explosions and explosive detonations. On this basis, we explored the propagation laws of shock waves and secondary pulsation waves (SPW) under different conditions. We also calculated and analyzed energy output characteristic parameters, such as shock wave energy and bubble energy. The results indicate that there are significant differences between copper wire and aluminum wire loads in UEWE. For copper wires with a diameter greater than 0.4 mm, the shock wave overpressure peak value significantly decreases, while for aluminum wires with a diameter greater than 0.5 mm, it slightly decreases. Both metals exhibit similar trends in parallel wire arrays, with the shock wave overpressure peak value initially increasing and then decreasing as the number of wires increases. Unlike underwater explosive detonations, the SPW peak value in UEWE may exceed that of the shock wave. For single wires, the SPW peak value of copper wires is generally higher than that of aluminum wires, but in wire arrays, the trend is reversed. The multi-wire parallel connection can improve the energy conversion efficiency of the shock waves. However, for bubble energy, under all conditions, a single aluminum wire with a diameter of 0.5 mm produced the maximum bubble energy, reaching 1023.1 J. These findings provide new insights into the energy features of UEWE.

The sensitivity analysis of geometric parameters on the power cycling reliability of bond wires

Considering the reliability of the bond wire comes as the main factor determining the reliability of power devices at present, and the geometric parameters of the bond wire have an in-negligible effect. A Finite Element (FE) simulation model based on a discrete device with TO-247 package and a single bond wire is established in this paper, and the influences of the geometric parameters are analyzed, which include the joint length L, the diameter D, and the aspect ratio λ. Then to understand the influence degree of the parameter on the reliability, the sensitivity analysis of these geometric parameters is carried out based on the sobol' method, using the Monte Carlo method for estimating the sensitivity index. The results show that increasing the joint length L, the diameter D and the aspect ratio λ all have a negative impact on the bond wire reliability, while a positive influence is presented by increasing the aspect ratio λ in the case without epoxy mold compound (EMC). This is because of the EMC's protective effect which inhibits the bond wire's thermal expansion. The aspect ratio λ is the most sensitive parameter of the three geometric parameters since it has the largest total sensitive index.

TROCHANTERIC OSTEOTOMY AND TRANSFER DURING TOTAL HIP ARTHROPLASTY IN PATIENTS WITH DISLOCATED DYSPLASTIC HIPS: UNION RATE USING MONOFILAMENT TRANSVERSE WIRE CERCLAGE

Securing the osteotomized greater trochanter (GT) during total hip arthroplasty (THA) for dislocated dysplastic hips (DDH) poses a significant challenge. This study evaluates the union rate and effectiveness of a 2-strand transverse wiring technique utilizing the lesser trochanter for wire anchorage and tensioning.A digastric anterior slide trochanteric osteotomy was performed in 106 patients (118 hips) undergoing THA for DDH. Following uncemented stem insertion, the GT was transferred and fixed to the lateral cortex of the proximal femur using monofilament stainless steel wires. In 72 out of 106 patients (80 hips), the GT was fixed with 2 transverse wire cerclages threaded through 2 drill holes in the base of the lesser trochanter, spaced vertically 5–10 millimeters apart. The wires were wrapped transversely over the GT and tightened, avoiding contact with its tendinous attachments. Patients were regularly monitored, and GT union was assessed clinically and radiographically.Patient ages ranged from 20 to 57 years (mean 35.5), with a follow-up period ranging from 1.5 to 12 years (mean 6.2). The mean union time was 3.3 months (range 2–7). Among all hips, two developed stable nonunion and single wire breakage, but no fragment displacement (2.5%). Two hips exhibited delayed union, eventually healing at 6 and 7 months after surgery.Reattachment of the greater trochanter utilizing a 2-strand transverse wire cerclage anchored at the base of the lesser trochanter demonstrated a high rate of union (97.5%) following THA in dislocated DDH cases.

Investigating the effect of rolling deformation on the electro-mechanical limits of Nb3Sn wires produced by RRP® and PIT technologies

Future high-field magnets for particle accelerators hinge on the crucial development of advanced Nb3Sn wires engineered to withstand the large stresses generated during magnet assembly and operation. The superconducting properties of Nb3Sn enable the design of compact accelerator-quality magnets above 10 T, but at the same time the brittleness and strain sensitivity of the material impose careful consideration of the mechanical limits. In addition, accelerator magnets are wound using Rutherford cables and the cabling process generates deformations in the wire that can affect its electro-mechanical performance. This paper reports on the impact of the rolling deformation on the transverse stress tolerance of high-performance restacked-rod-process (RRP®) and powder-in-tube (PIT) Nb3Sn wires. Rolling deformation was used to mimic the effect of cabling on the wire shape. Deformed samples were compared to reference round wires in term of stress dependence and irreversible limit (σ irr) of the critical current (I c) under transverse compressive loads up to 240 MPa. Experiments were performed at 4.2 K, 19 T, on resin-impregnated single wires that imitate the operating conditions in a Rutherford cable of an accelerator magnet. The results show that rolling deformation has a detrimental effect on the initial I c of PIT wires, but it does not influence the behavior of the wire under stresses above 70 MPa. On the other hand, the deformation of RRP® wires leads to an improved σ irr without affecting the initial I c. Additionally, a 2D-mechanical finite element method model of the RRP® wire was developed to investigate the impact of the wire geometry on the plastic deformation of the copper matrix, which induces residual stresses on Nb3Sn and is the main cause for the permanent reduction of I c. Based on the model results, an alternative layout of the wire was proposed that improves its stress tolerance without affecting its electrical transport properties.

Enabling data-driven and bidirectional model development in Verilog-A for photonic devices.

We present a method to model photonic components in Verilog-A by introducing bidirectional signaling through a single port. To achieve this, the concept of power waves and scattering parameters from electromagnetism are employed. As a consequence, one can simultaneously transmit forward and backward propagating waves on a single wire while also capturing realistic, measurement-backed responses of photonic components in Verilog-A. We demonstrate examples to show the efficacy of the proposed technique in accounting for critical effects in photonic integrated circuits such as Fabry-Perot cavity resonance, reflections to lasers, reflection cancellation circuits, etc. Our solution makes electronic-photonic co-simulation more intuitive and accurate.

Narrow gap multi-pass laser welding with 52M/308L double wires filler addition for SA508/316L dissimilar metals

Recently, considerable effort has been directed at the development of laser welding with wire filler addition as an alternative manufacture technique for the substantial productivity gains it would offer to the nuclear pressure vessels fabrication. However, single wire filler such as 52M and 308 L addition is difficult to take into account many properties such as the strength, toughness and resistance to stress corrosion cracking at the same time. In this work we evaluate the feasibility of applying 52 M/308 L dissimilar double wires filler addition for the multi-pass narrow gap laser welding (NGLW) of SA508/316 L dissimilar metals. The objectives of this paper is to regulate the microstructure of the welded joint by adjusting the ratio of the 52 M/308 L double wires filler. The results showed that welded joints without crack and lack-of-fusion were acquired. An excellent comprehensive property welded joint with relative high hardness and low residual stresses is acquired when the 52 M/308 L double wires proportion was 75 %:25 %. The results also indicated that a certain proportion of 308 L stainless steel wire filler addition was conducive to reducing the microhardness of the welded joint. However, when that ratio of the 308 L wire was up to 75 %, harmful element S was obtained in the precipitation zone, which might reduce the mechanical properties of the welded joints.

Microstructure and mechanical property improvement of concurrent wire-powder feeding laser melting deposition Ti-6Al-4V via TiC addition

Wire-feed laser metal deposition (LMD-W) offers a high deposition rate and low cost, making it an effective solution for reducing costs and enhancing efficiency in manufacturing large-scale titanium aerospace components. Currently, the material used for LMD-W is typically a single alloy wire, which limits the flexibility and functionality of manufacturing composite materials. This work employed a novel concurrent wire-powder feeding laser metal deposition (LMD-WP) process to manufacture TiC/Ti-6Al-4V composite. In the LMD-WP method, Ti-6Al-4V wire was fed laterally, while TiC particles were delivered coaxially. Only 1.0 wt% TiC particles were added to prevent excessive TiC, which could cause stress concentration and increase crack sensitivity. The microstructure and mechanical properties of Ti-6Al-4V alloy and TiC/Ti-6Al-4V composite were investigated. The results indicate that with coaxial TiC particle addition, the α-Ti in TiC/Ti-6Al-4V is noticeably refined. Additionally, in situ TiC acts as heterogeneous nucleation sites, restricting α-Ti growth and reducing its aspect ratio. Furthermore, TiC particles weakened the α-Ti texture in the (0001) and (11–20) directions. Moreover, adding TiC particles significantly enhanced tensile strength, with the yield strength reaching 950 MPa and the ultimate tensile strength reaching 1048 MPa. Compared to Ti-6Al-4V alloy fabricated by LMD-W, this represents an increase of 11.25% and 10.72%, respectively. The improvement in tensile properties is principally ascribed to grain boundary strengthening, Orowan strengthening and dislocation density strengthening. This work introduces an innovative approach and abundant data for the additive manufacturing of TiC/Ti-6Al-4V composite with high efficiency and low cost.

Topological Kondo effect with spinful Majorana fermions

Motivated by the importance of studying topological superconductors beyond the mean-field approximation, we here investigate mesoscopic islands of time-reversal-invariant topological superconductors. We characterize the spectrum in the presence of strong order-parameter fluctuations in the presence of an arbitrary number of Kramers pairs of Majorana edge states and study the effect of coupling the Coulomb blockaded island to external leads. In the case of an odd fermionic parity on the island, we derive an unconventional Kondo Hamiltonian in which metallic leads couple to both topological Majorana degrees of freedom (which keep track of the parity in different leads) and the overall spin 12 in the island. For the simplest case of a single wire (two pairs of Majorana edge states), we demonstrate that anisotropies are irrelevant in the weak coupling renormalization group flow. This permits us to solve the Kondo problem in the vicinity of a Toulouse-type point using Abelian bosonization. We demonstrate a residual ground-state entropy of ln(2), which is protected by spin-rotation symmetry, but reduced to ln(2) (as in the spinless topological Kondo effect) by symmetry-breaking perturbations. In the symmetric case, we further demonstrate the simultaneous presence of both Fermi-liquid and non-Fermi-liquid-like thermodynamics (depending on the observable) and derive charge and spin transport signatures of the Coulomb blockaded island. Published by the American Physical Society 2024

Monitoring tendon breaks in concrete structures at different depths using distributed fiber optical sensors

Unannounced tendon breaks are a dreaded failure mechanism in concrete bridges. The failure of single wires or tendons does not necessarily cause cracking of the concrete. Thus, the damage cannot be detected by visual inspection. But, in the case of tendons bonded in concrete, re-anchoring causes characteristic local strain fields: tensile strains occur between the crack edges while three-dimensional compressive strains develop in the area around. On the surface, these strains are small and depend, e.g., on the concrete stiffness, the depth of the tendon inside the member and the anchorage length. Such strain fields can be measured by fiber optical sensors on the surface in two dimensional grids. By evaluating the backscatter of emitted light beams, minimal strain changes (uncertainty: ±1 µm/m) can be detected in quasi-continuous resolution (0.65 mm pitch). An experimental investigation on a prestressed concrete beam with bonded tendons is presented. Gradually, three tendons of 10.5 mm diameter were mechanically cut to simulate failure, while longitudinal strains were measured on a 2D grid at the surface. With a prestressing force of 64.5 kN and up to a depth of 25 cm breaks of the tendons could be detected. They caused strains about 10-15 µm/m at the surface at maximum. For varying tendon positions, the effect of depth on the strain is investigated by two sided measurements. As the distance between the break and the concrete surface increases, the strain significantly decreases but remains detectable. In the future, the results enable deeper analyses of the most influential parameters. The final aim remains to precisely detect the position and number of failed wires or tendons just from the strain signal at the surface.