Single-walled Carbon Nanotubes Composites Research Articles

Thermoelectric generator and temperature sensor based on polyamide doped n-type single-walled nanotubes toward self-powered wearable electronics

Due to its ability to convert body heat into electricity, organic thermoelectric material is considered a promising and smart maintenance-free power source to charge wearable electronics. However, developing flexible n-type organic thermoelectric materials and wearable p/n junction thermoelectric devices remains challenging. In this work, two insulated polyamides (PA6 and PA66) that have been widely used as fiber materials are employed as novel dopants for converting p-type single-walled carbon nanotubes (SWCNTs) to n-type thermoelectric materials. Because of the electron transferability of the amide group, polyamide-doped SWCNTs exhibit excellent thermopower values as large as −56.0 μV K−1 for PA66, and −54.5 μV K−1 for PA6. Thermoelectric devices with five p/n junctions connected in series are fabricated. The testing device produces a thermoelectric voltage of 43.1 mV and generates 1.85 μW thermoelectric power under temperature gradients of approximately 80 K. Furthermore, they display charming capability for temperature recognition and monitoring human activities as sensors. These promising results suggest that the flexible polyamide-doped SWCNT composites herein have high application potential as wearable thermoelectric electronics.

Effect of the reinforcement phase on the electrical and mechanical properties of Cu–SWCNTs nanocomposites

In this research a pre-treatment of single-walled carbon nanotubes (SWCNTs) was performed to obtain Cu–SWCNTs composites by powder metallurgy technique. The SWCNTs were subjected to a chemical functionalization in acidic medium followed by a copper coating to improve their incorporation into the metal matrix. The results revealed a considerable inclusion of carboxyl, carbonyl and hydroxyl groups in the nanotubes, maintaining their structural integrity which was demonstrated by characterization using X-ray photoelectronic spectroscopy (XPS), scanning electron microscopy (SEM) and Raman spectroscopy techniques. The electroless process used allowed a complete reduction of copper sulfate to a metallic copper obtaining a suitable and homogeneous carbon nanotubes incorporation into the copper matrix. Microhardness measurements of the Cu–0.01 % SWCNT composite presented an improvement of 13 % compared with pure copper. Furthermore, this composite showed the best tribological properties obtaining a wear rate of 2.1 × 10−4 mm3/Nm, 18 % better than Cu, which was associated with the improved dispersion of the SWCNTs bundles into the matrix, and with a lower amount of surface defects. The maximum electrical conductivity obtained was 96 % IACS in the samples with the least amount of reinforcement phase which confirms their homogeneity into the copper matrix.

Effects of preparation method on thermoelectric properties of poly(aniline‐co‐3,4‐ethylenedioxythiophene)/SWCNT composites

AbstractComposites of conducting polymer and single‐walled carbon nanotubes (SWCNTs) are attracting great attentions in harvesting low‐grade waste heat. Prefabricated SWCNTs film used as the working electrode was placed at the liquid interface between the inorganic phase (dilute sulfuric acid solution) and the organic phase consisting of dichloromethane (DCM), aniline (ANI), and 3,4‐ethylenedioxythiophene (EDOT), together with a platinum wire (the counter electrode) and a silver chloride (AgCl/Ag) electrode (the reference electrode), to perform electrochemical polymerization of ANI and EDOT at the liquid interface. Thermoelectric (TE) composites of poly(ANI‐co‐EDOT) and SWCNTs were produced. Compared with composites from ultrasonic mixing and coating methods, the 10 wt% SWCNTs‐composites in situ formed in electrochemical polymerization have the highest power factor (PF) of 41.56 ± 3.58 μW m−1 K−2, higher than the PF values of the composites formed by other two methods. The work indicates that the TE properties of ANI‐EDOT copolymer/SWCNT (poly[ANI‐co‐EDOT]/SWCNT) composites prepared by electrochemical polymerization were better than those of the composites obtained by physical mixing the electrochemically synthesized poly(ANI‐co‐EDOT) with SWCNTs. Moreover, SWCNTs treated with sodium dodecylbenzene sulfonate (SDBS) could further improve the TE properties of the composites.

Process controlled microstructure of polyvinylidene fluoride/functionalized single walled carbon nanotube composites

AbstractPolyvinylidene fluoride (PVDF)‐functionalized single walled carbon nanotube (FSWCNT) film composites were prepared by two different process conditions—air drying and vacuum drying. Though reports on –PVDF‐FSWCNT composites are available, we provide a new outlook here, which is based on optimized functionalization and novel processing conditions. The microstructural and phase changes occurring in PVDF having nanotubes functionalized for different extent of time were investigated and confirmed that those functionalized for 4 h (FSWCNAT‐4) create polar γ phase in PVDF with improved mechanical and electrical properties. X‐ray photoelectron spectroscopy studies showed that PVDF/FSWCNT‐4 composites have the maximum percentage of functional groups. It is also found that PVDF/FSWCNT‐4 composite films prepared through air drying were rough and had a cloudy appearance suitable for applications demanding open porous structures, whereas those prepared through vacuum drying process were smooth and homogeneous with high optical transparency, suitable for microelectronic applications. Thus, by suitably controlling the processing conditions and by using optimally functionalized nanotubes, PVDF films with multifunctional properties could be achieved. In order to extract the full capabilities of PVDF/SWCNT films, functionalization of the nanotube together with processing conditions plays a significant role.

Investigations on dielectric and mechanical properties of poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP)/single-walled carbon nanotube composites

Investigations on dielectric and mechanical properties of poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP)/single-walled carbon nanotube composites

Compositing Benzothieno[3,2-b]Benzofuran Derivatives with Single-Walled Carbon Nanotubes for Enhanced Thermoelectric Performance.

Although numerous thermoelectric (TE) composites of organic materials and single-walled carbon nanotubes (SWCNTs) have been developed in the past decade, most of the research has been related to polymers without much on organic small molecules (OSMs). In this work, benzothieno[3,2-b]benzofuran (BTBF) and its derivatives (BTBF-Br and BTBF-2Br) were synthesized and their TE composites with SWCNTs were prepared. It is found that the highest molecular orbital level and band gap (Eg) of BTBF, BTBF-Br, and BTBF-2Br gradually decrease upon the introduction of electron-withdrawing Br group on BTBF. These changes significantly improve the Seebeck coefficient and power factor (PF) of OSM/SWCNT composites. An appropriate energy barrier between BTBF-2Br and SWCNTs promotes the energy filtering effect, which further contributes to the enhancement of composites' thermoelectric properties. The composites of SWCNTs and BTBF-2Br with the smallest Eg (4.192 eV) afford the best thermoelectric performance with the room temperature power factor of 169.70 ± 3.46 μW m-1 K-2 in addition to good mechanical flexibility and thermal stability. This study provides a feasible strategy for the preparation of OSM/SWCNT composites with improved thermoelectric properties.

Optimization of electrical and mechanical properties of a single-walled carbon nanotube composite using a three-roll milling method

In this study, the electrical and mechanical properties of carbon nanotube (CNT)/polydimethylsiloxane (PDMS) composites were optimized using a three-roll milling dispersion method. Depending on the number of CNT walls, such as single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs), the three-roll milling conditions required to optimize the electrical conductivity of CNT/PDMS composites are quite different. In addition, the mechanical properties of the CNT/PDMS composites depend on the dispersion time. These properties were improved under an appropriate three-roll milling time but gradually deteriorated after excessive processing time. To demonstrate and optimize this phenomenon, various mechanical, electrical, and thermal properties of the CNT/PDMS composites were measured with respect to the type of CNT, milling time, and filler weight fraction. Morphological and structural analyses were also conducted on the CNT fillers and composites after milling.

Molecular Dynamics Modeling for the Determination of Elastic Moduli of Polymer-Single-Walled Carbon Nanotube Composites.

The use of carbon nanotubes to improve the mechanical properties of polymers is one of the promising directions in materials science. The addition of single-walled carbon nanotubes (SWCNTs) to a polymer results in significant improvements in its mechanical, electrical, optical, and structural properties. However, the addition of SWCNTs does not always improve the polymer properties. Also, when a certain content of SWCNTs is exceeded, the mechanical properties of the nanocomposite become worse. This article reports the results of computer simulations for predicting the mechanical properties of polymer/single-walled carbon nanotube nanocomposites. The efficiency of reinforcing polymer composites is considered depending on the concentration of carbon nanotubes in the polymer matrix, their size, and structure. The elastic moduli of the nanocomposites are predicted using computer simulations for unit cell tension (0.1%). General trends in the mechanical properties of composites with polypropylene (PP), poly(ethyl methacrylate) (PEMA), polystyrene (PS) matrices, and SWCNTs are shown.

Nonlinear Optical Response of Dispersed Medium Based on Conjugates Single-Walled Carbon Nanotubes with Phthalocyanines

Nanosecond lasers have recently been widely involved in human activity. However, high-intensity laser radiation can cause severe damage to organs of vision and expensive photonic devices. Radiation in the near UV range is especially dangerous for human eyes, since it is strongly absorbed by biological media and is also invisible, i.e., the reaction time of the eye to such radiation is much lower than that of visible light. Passive limiters have high transmission (>70%) at a low light intensity and begin to “darken” only when the threshold value of the laser radiation intensity is reached. In this work, we studied liquid nanodispersed nonlinear optical limiters based on hybrids of single-walled carbon nanotubes (SWCNTs) with metal-free tetra(hydroxy)phthalocyanine (OH)4PcHH). The value of the hydrodynamic radius of separate particles after (OH)4PcHH binding increased from 288 ± 55 nm to 350 ± 60 nm, which confirms the attachment of phthalocyanine complexes to nanotubes. The third harmonic of a Nd:YAG nanosecond laser (355 nm, 20 ns) was used to study the nonlinear optical response. Based on a Z-scan with open-aperture and input-output dependence curves, third-order nonlinear optical absorption coefficients of 149, 236, and 229 cm/GW were obtained for dispersions of composites of SWCNTs and (OH)4PcHH in water, dimethylformamide (DMF), and dimethylsulfoxide (DMSO), respectively. Threshold values did not exceed 100 mJ/cm2. The Z-scan showed a gradual decrease in the duration of the laser pulse by 53%; however, near the focus, there was a sharp increase in the duration of the transmitted pulse, reaching a value of 29 ns in z = 0. This phenomenon confirms the occurrence of reverse saturable absorption in the investigated media and can be used in photonic devices to control the temporal characteristics of the signal. Thus, the possibility of protection of sensitive photonic devices and human eyes from nanosecond laser pulses in the near UV range by nanodispersed liquid media based on composites of SWCNTs with (OH)4PcHH has been discussed in this paper.

PMMA/SWCNT Composites with Very Low Electrical Percolation Threshold by Direct Incorporation and Masterbatch Dilution and Characterization of Electrical and Thermoelectrical Properties.

In the present study, Poly(methyl methacrylate) (PMMA)/single-walled carbon nanotubes (SWCNT) composites were prepared by melt mixing to achieve suitable SWCNT dispersion and distribution and low electrical resistivity, whereby the SWCNT direct incorporation method was compared with masterbatch dilution. An electrical percolation threshold of 0.05-0.075 wt% was found, the lowest threshold value for melt-mixed PMMA/SWCNT composites reported so far. The influence of rotation speed and method of SWCNT incorporation into the PMMA matrix on the electrical properties and the SWCNT macro dispersion was investigated. It was found that increasing rotation speed improved macro dispersion and electrical conductivity. The results showed that electrically conductive composites with a low percolation threshold could be prepared by direct incorporation using high rotation speed. The masterbatch approach leads to higher resistivity values compared to the direct incorporation of SWCNTs. In addition, the thermal behavior and thermoelectric properties of PMMA/SWCNT composites were studied. The Seebeck coefficients vary from 35.8 µV/K to 53.4 µV/K for composites up to 5 wt% SWCNT.

Analysis of the Structure and Properties of Hybrid Carbon Fiber Reinforced Polymer / Single Wall Carbon Nanotube Composites by Thermogravimetry and Scanning Electron Microscopy

Analysis of the Structure and Properties of Hybrid Carbon Fiber Reinforced Polymer / Single Wall Carbon Nanotube Composites by Thermogravimetry and Scanning Electron Microscopy

High thermoelectric performance of flexible nanocomposite films based on Bi2Te3 nanoplates and carbon nanotubes selected using ultracentrifugation

Thermoelectric generators with flexibility and high performance near 300 K have the potential to be employed in self-supporting power supplies for Internet of Things (IoT) devices. Bismuth telluride (Bi2Te3) exhibits high thermoelectric performance, and single-walled carbon nanotubes (SWCNTs) show excellent flexibility. Therefore, composites of Bi2Te3 and SWCNTs should exhibit an optimal structure and high performance. In this study, flexible nanocomposite films based on Bi2Te3 nanoplates and SWCNTs were prepared by drop casting on a flexible sheet, followed by thermal annealing. Bi2Te3 nanoplates were synthesized using the solvothermal method, and SWCNTs were synthesized using the super-growth method. To improve the thermoelectric properties of the SWCNTs, ultracentrifugation with a surfactant was performed to selectively obtain suitable SWCNTs. This process selects thin and long SWCNTs but does not consider the crystallinity, chirality distribution, and diameters. A film consisting of Bi2Te3 nanoplates and the thin and long SWCNTs exhibited high electrical conductivity, which was six times higher than that of a film with SWCNTs obtained without ultracentrifugation; this is because the SWCNTs uniformly connected the surrounding nanoplates. The power factor was 6.3 μW/(cm K2), revealing that this is one of the best-performing flexible nanocomposite films. The findings of this study can support the application of flexible nanocomposite films in thermoelectric generators to provide self-supporting power supplies for IoT devices.

Catalyst controlled synthesis of porous organic polymers and their SWCNT composites for high performance supercapacitor applications

The present study discusses the importance of catalyst selectivity for the preparation of homocoupling polymers for CO2 gas adsorption and supercapacitor applications. N, N′-bicarbazole based conjugated porous organic polymers (TGs) have been synthesized through sonogashira (TGPd/Cu), glaser (TGCuCl) and Eglington (TGCu(OAc)2) protocols. Here, TGPd/Cu acquired high specific surface area (923 m2 g−1), uniform pores (2 nm), and excellent CO2 adsorption (16.1 wt%). The synthesized TG polymers was utilized as efficient electrode for supercapacitor studies. TGPd/Cu exhibits a maximum capacitance of 248 F g−1 at 0.5 A g−1 current density. To enhance the electrochemical performances, the prepared TGs melded with single walled carbon nanotubes (SWCNT) and the fabricated TGPd/Cu/SWCNT electrode demonstrates a maximum specific capacitance of 523 F g−1 at 0.5 A g−1 current density with an outstanding cycling stability of 98.1% after 5000 cycles in three electrode system. The fabricated TGPd/Cu/SWCNT device showed a capacitance of 129 F g−1 at 0.5 A g−1 with high-capacity retention of 82.5% after 5000 cycles in two electrode system. Consequently, TGPd/Cu/SWCNT appear to be promising electroactive material for use as electrode in electrochemical energy storage systems. The satisfactory electrochemical performance can be attributed to the successfully π- π stacking of the TGPd/Cu onto the nanotube surface and the synergy between TGPd/Cu and highly conductive SWCNT which significantly advanced the electron transport properties of the explored composites.

Development of Electromagnetic-Wave-Shielding Polyvinylidene Fluoride-Ti3C2Tx MXene-Carbon Nanotube Composites by Improving Impedance Matching and Conductivity.

Absorption-dominated electromagnetic interference (EMI) shielding is attained by improving impedance matching and conductivity through structural design. Polyvinylidene fluoride (PVDF)-Ti3C2Tx MXene-single-walled carbon nanotubes (SWCNTs) composites with layered heterogeneous conductive fillers and segregated structures were prepared through electrostatic flocculation and hot pressing of the PVDF composite microsphere-coated MXene and SWCNTs in a layer-by-layer fashion. Results suggest that the heterogeneous fillers improve impedance matching and layered coating, and hot compression allows the MXene and SWCNTs to form a continuous conducting network at the PVDF interface, thereby conferring excellent conductivity to the composite. The PVDF-MXene-SWCNTs composite showed a conductivity of 2.75 S cm-1 at 2.5% MXene and 1% SWCNTs. The EMI shielding efficiency (SE) and contribution from absorption loss to the total EMI SE of PVDF-MXene-SWCNTs were 46.1 dB and 85.7%, respectively. Furthermore, the PVDF-MXene-SWCNTs composite exhibited excellent dielectric losses and impedance matching. Therefore, the layered heteroconductive fillers in a segregated structure optimize impedance matching, provide excellent conductivity, and improve absorption-dominated electromagnetic shielding.

Influence of Polyvinylpyrrolidone on Thermoelectric Properties of Melt-Mixed Polymer/Carbon Nanotube Composites.

For thermoelectric applications, both p- and n-type semi-conductive materials are combined. In melt-mixed composites based on thermoplastic polymers and carbon nanotubes, usually the p-type with a positive Seebeck coefficient (S) is present. One way to produce composites with a negative Seebeck coefficient is to add further additives. In the present study, for the first time, the combination of single-walled carbon nanotubes (SWCNTs) with polyvinylpyrrolidone (PVP) in melt-mixed composites is investigated. Polycarbonate (PC), poly(butylene terephthalate) (PBT), and poly(ether ether ketone) (PEEK) filled with SWCNTs and PVP were melt-mixed in small scales and thermoelectric properties of compression moulded plates were studied. It could be shown that a switch in the S-value from positive to negative values was only possible for PC composites. The addition of 5 wt% PVP shifted the S-value from 37.8 µV/K to -31.5 µV/K (2 wt% SWCNT). For PBT as a matrix, a decrease in the Seebeck coefficient from 59.4 µV/K to 8.0 µV/K (8 wt% PVP, 2 wt% SWCNT) could be found. In PEEK-based composites, the S-value increased slightly with the PVP content from 48.0 µV/K up to 54.3 µV/K (3 wt% PVP, 1 wt% SWCNT). In addition, the long-term stability of the composites was studied. Unfortunately, the achieved properties were not stable over a storage time of 6 or 18 months. Thus, in summary, PVP is not suitable for producing long-term stable, melt-mixed n-type SWCNT composites.

Structural Integrity Assessment of Aligned and Non-aligned Single Walled Carbon Nanotubes in Epoxy Resin

Carbon nanotubes have gained popularity due its unique electrical and thermal properties and high strength, widely finding it application in medical and electrical field. In the presented study the single walled carbon nanotubes (SWCNT) are assumed to be aligned using a DC electric field, taking into account transportation phenomena like the rotation of tube and its polarization to form chain like structure. Authors have examined and compared the structural properties under tensile loading of aligned and non-aligned single walled carbon nanotubes SWCNT in epoxy matrix using finite element analysis. COMSOL Multiphysics has been used to model the specimens and investigate its properties. The result lays out trends and relation between various parameters and the strength of the epoxy based SWCNT composite. The study draws out result on how changes in parameters of epoxy based SWCNT composite changes its physical properties.

Electrical and Mechanical Properties of Polymer Composite through the Use of Single-Walled Carbon Nanotube and Multi-Walled Carbon Nanotube

To manufacture composites with required properties, it is extremely important to select an appropriate filler. Carbon-based nano materials such as carbon black, graphene and carbon nanotube (CNT) have been extensively investigated as reinforcing and conducting fillers. Because of their high aspect ratio coupled with superior physical properties, 1-dimensional CNTs are ideal as filler materials to impart electrical conductivity to insulating polymers, while enhancing mechanical strength. In this study, we investigated the piezo-resistive and mechanical properties of composites consisting of two types of CNT classified as multi-walled CNT (MWNT) or single-walled CNT (SWNT) depending on the number of walls. Since MWNT and SWNT have different physical properties such as specific surface area and aspect ratio, this can affect the composite’s performance. To more effectively evaluate the effect of MWNTs and SWNTs in composites, we used thermoplastic polyurethane (TPU) as a matrix, which is an insulating stretchable elastomer. Morphological and mechanical/electrical characterizations were conducted to determine differences in the MWNT and SWNT composites. In addition, we conducted dynamic strain sensing tests on each type of CNT composites to compare the sensitivity as a strain sensor. Differences in piezo-resistive behaviors were attributed to the loss of electrical contact points during stretching. These results can serve as a useful design guideline for the wider use of CNT composites.

Simultaneously Achieving Green p- and n-Type Single-Walled Carbon Nanotube Composites by Natural Amino Acids with High Performance for Thermoelectrics

Simultaneously Achieving Green p- and n-Type Single-Walled Carbon Nanotube Composites by Natural Amino Acids with High Performance for Thermoelectrics

Thermoelectric properties of PbTe based single-walled carbon nanotube (SWCNT) composites

Thermoelectric has long been recognized as a promising technology due to its ability to harvest waste heat from different sources, such as the Sunlight, vehicles, and energy-intensive industries, and thereby convert it into electricity without emitting greenhouse gases, so providing distributed solutions for sustainable energy challenges and energy efficiency issues worldwide. Lead Telluride (PbTe) is the classic thermoelectric material; however, its applications are limited by its low efficiency. The goal of the present research is to improve the energy conversion efficiency of PbTe by mixing single-walled carbon nanotubes (SWCNTs) via simple powder processing and utilizing nanostructuring and quantum confinement effects in a synergistic way. PbTe based composites incorporating different vol% of SWCNTs were fabricated through the high-frequency induction heating furnace at ~450°C. Thermoelectric characteristics of bulk samples were tested at temperatures ranging from ~300 to ~530K. With the inclusion of nanotubes, the electrical conductivity behaviour changes from semi-metallic in pristine PbTe to semi-conducting in composites. This shows that the semiconducting nature of SWCNTs plays a major role in electrical transport. As a result, the composites’ effective electrical conductivities were lowered near room temperature, with the lowest values observed at 0.5 vol% of SWCNTs. When compared to pure PbTe, the Seebeck coefficient of the 0.5 vol% of PbTe composite improves at ambient temperature and gradually drops after ~375K. Thermal conductivity of all the composites reduces and substantial reduction was observed at 0.5 vol% of SWCNTs. The large transition from semi-metallic to semi-conducting transport in pristine PbTe to composites, as well as enhanced short-range carrier scattering, are responsible for lowering electrical conductivity and hence composites’ power factor. As a result, the significant reduction in thermal conductivities could not compensate for the loss of power factor, resulting in lower ZT values from pristine PbTe.

Supercapacitor based on polymeric binary composite of polythiophene and single-walled carbon nanotubes

The aim of this work is to fabricate supercapacitor electrode based on poly (3-hexyl-thiophene-2, 5-diyl) (P3HT) and single-walled carbon nanotubes (SWCNTs) nanocomposites with different ratios onto a graphite sheet as a substrate with a wide voltage window in nonaqueous electrolyte. Structural, morphological and electrochemical properties of the prepared nanocomposites of P3HT/SWCNTs were studied and discussed. The electrochemical properties included cyclic voltammetry (CV), galvanostatic charging-discharging (GCD), and electrochemical impedance spectroscopy (EIS) were investigated. The obtained results indicated that P3HT/SWCNTs nanocomposite possesses higher specific capacitance than that present in its individual component. The high electrochemical performance of the nanocomposite was due to formation of microporous structure which facilitates ions diffusion and electrolyte penetration in these pores. The morphological micrographs of the purified SWCNTs had buckypaper structure while the photomicrographs of P3HT/SWCNTs showed that SWCNTs appear behind and front of the P3HT nanospheres. The specific capacitance of 50% SWCNTs at 0.5 Ag−1 was found to be 245.8 Fg−1 compared with that of pure P3HT of 160.5 Fg−1.