Single-walled Carbon Nanotube Nanocomposites Research Articles

Effect of the reinforcement phase on the electrical and mechanical properties of Cu–SWCNTs nanocomposites

In this research a pre-treatment of single-walled carbon nanotubes (SWCNTs) was performed to obtain Cu–SWCNTs composites by powder metallurgy technique. The SWCNTs were subjected to a chemical functionalization in acidic medium followed by a copper coating to improve their incorporation into the metal matrix. The results revealed a considerable inclusion of carboxyl, carbonyl and hydroxyl groups in the nanotubes, maintaining their structural integrity which was demonstrated by characterization using X-ray photoelectronic spectroscopy (XPS), scanning electron microscopy (SEM) and Raman spectroscopy techniques. The electroless process used allowed a complete reduction of copper sulfate to a metallic copper obtaining a suitable and homogeneous carbon nanotubes incorporation into the copper matrix. Microhardness measurements of the Cu–0.01 % SWCNT composite presented an improvement of 13 % compared with pure copper. Furthermore, this composite showed the best tribological properties obtaining a wear rate of 2.1 × 10−4 mm3/Nm, 18 % better than Cu, which was associated with the improved dispersion of the SWCNTs bundles into the matrix, and with a lower amount of surface defects. The maximum electrical conductivity obtained was 96 % IACS in the samples with the least amount of reinforcement phase which confirms their homogeneity into the copper matrix.

Synergistic Interactions in Sequential Process Doping of Polymer/Single-Walled Carbon Nanotube Nanocomposites for Enhanced n-Type Thermoelectric Performance.

This study focuses on the fabrication of nanocomposite thermoelectric devices by blending either a naphthalene-diimide (NDI)-based conjugated polymer (NDI-T1 or NDI-T2), or an isoindigo (IID)-based conjugated polymer (IID-T2), with single-walled carbon nanotubes (SWCNTs). This is followed by sequential process doping method with the small molecule 4-(2,3-dihydro-1,3-dimethyl-1H-benzimidazol-2-yl)-N,N-dimethylbenzenamine (N-DMBI) to provide the nanocomposite with n-type thermoelectric properties. Experiments in which the concentrations of the N-DMBI dopant are varied demonstrate the successful conversion of all three polymer/SWCNT nanocomposites from p-type to n-type behavior. Comprehensive spectroscopic, microstructural, and morphological analyses of the pristine polymers and the various N-DMBI-doped polymer/SWCNT nanocomposites are performed in order to gain insights into the effects of various interactions between the polymers and SWCNTs on the doping outcomes. Among the obtained nanocomposites, the NDI-T1/SWCNT exhibits the highest n-type Seebeck coefficient and power factor of -57.7 µV K-1 and 240.6 µW m-1 K-2 , respectively. However, because the undoped NDI-T2/SWCNT exhibits a slightly higher p-type performance, an integral p-n thermoelectric generator is fabricated using the doped and undoped NDI-T2/SWCNT nanocomposite. This device is shown to provide an output power of 27.2 nW at a temperature difference of 20 K.

Finite element based indentation contact analysis of SWCNT nano-composite

The focus of the present study is to simulate the indentation type contact behaviour of single walled carbon nanotube (SWCNT) based nanocomposite. The contact system consists of a deformable Aluminium matrix, reinforced with a group of SWCNTs, and a conical indenter which is assumed as rigid. Downward and upward displacement is imparted on the conical indenter in order to simulate the loading and unloading phases of the contact. The model has been developed using APDL code on the ANSYS platform. Adequacy and validity of the model has been established by comparison with results from already published papers available in literature and the matching between the two sets of results is found to be excellent. In terms of results, contact forces, contact area, contact pressure and deformation behaviour are extracted from the analysis with varying wall thickness of CNTs. Detailed analysis of the obtained results has been carried out and it is found that sink in and pile up (in one particular scenario) behaviour is exhibited. It is also found that due to high deformation of the tubes at high indentation depth, there is material flow towards the axis of symmetry and creation of small elastic zones in the matrix material.

Fabrication and characterization of Trans‐1,4‐polyisoprene/carbon nanotubes nanocomposites with thermo‐ and electro‐active shape memory effects

AbstractTrans‐1,4‐polyisoprene/single wall carbon nanotubes nanocomposites (TPI/SWCNT) nanocomposites with thermo‐ and electro‐active shape memory performance were prepared via solution blending and vulcanization. Herein, the mechanical, thermo‐mechanical, electric conductivity properties, thermo‐ and electro‐active shape memory properties of pure TPI and TPI/SWCNT nanocomposites were investigated. It was demonstrated that the addition of SWCNT into the TPI matrix can improve its crystallinity, crystallization temperature and storage modulus characteristics, and form a two‐crystal melting peak. Compared with the pure TPI, the TPI/SWCNT nanocomposites need more time to recover to their initial shape under thermo stimulus, and the recovery ratio of TPI/SWCNT nanocomposites with 2.5 wt% SWCNT was about 92%. Moreover, pure TPI and TPI/SWCNT nanocomposites with SWCNT content of up to 2.0 wt% under 30 V could not recover under electro stimulus, but the TPI/SWCNT nanocomposites with 2.5 wt% SWCNT displayed electro‐active shape recovery property with a recovery ratio of 87.5%, because a certain amount of SWCNT can provide joule heat to melt the crystals completely and unfreeze cross‐linking network of TPI.

Investigation of the structure and tensile strength of ultrahigh molecular weight polyethylene and amide functionalized single-walled carbon nanotubes nanocomposites

Investigation of the structure and tensile strength of ultrahigh molecular weight polyethylene and amide functionalized single-walled carbon nanotubes nanocomposites

Separating Curing and Temperature Effects on the Temperature Coefficient of Resistance for a Single-Walled Carbon Nanotube Nanocomposite

The temperature coefficient of resistance (TCR) determines the electrical performance of materials in electronics. For a carbon nanotube (CNT) nanocomposite, change of resistivity with temperature depends on changes in CNT intrinsic conductivity, tunnelling thresholds and distances, matrix' coefficient of thermal expansion, and other factors. In our study, we add one more influencing factor-the degree of cure. Complexities of the curing process cause difficulties to predict, or even measure, the curing state of the polymer matrix while uncertainty in the degree of cure influences TCR measurements leading to biased values. Here we study the influence of the cure state on the TCR of a single-walled CNT/epoxy polymer nanocomposite. For the given degree of cure, TCR measurements are conducted in the temperature range 25-100 °C, followed by the next 24 h of post-curing and a new cycle of measurements, 8 cycles in total. We find that contrary to industry practice to expect a high degree of cure after 3 h at 130 °C, the curing process is far from reaching the steady state of the material and continues at least for the next 72 h at 120 °C, as we observe by changes in the material electrical resistivity. If TCR measurements are conducted in this period, we find them significantly influenced by the post-curing process continuing in parallel, leading in particular to non-monotonic temperature dependence and the appearance of negative values. The unbiased TCR values we observe only when the material reaches the steady state are no longer influenced by the heat input. The dependence becomes steady, monotonically increasing from near zero value at room temperature to 0.001 1/°C at 100 °C.

Solvatochromism in SWCNTs suspended by conjugated polymers in organic solvents.

Despite the extensive utilization of carbon nanostructures as sensors, the factors that most affect their performance remain insufficiently understood. Many nanocarbon-based sensors are either processed in liquid environments or applied as liquid suspensions, which leads to solvatochromism, substantially influencing the underlying optical transitions. Most of the principles established so far apply only to nanocarbon species dispersed in polar environments by common surfactants, so the reported findings are not universal. For instance, they cannot describe the behavior of single-walled carbon nanotubes (SWCNTs) suspended in organic solvents by conjugated polymers (CPs), which have recently received considerable attention from the scientific community. Our research responds to this lack of knowledge and provides a thorough understanding of this topic by investigating SWCNT nanocomposites based on polyfluorenes and their co-polymers. A careful selection of an autonomous reference and precise spectral analysis allowed us to measure absolute solvatochromic shifts, by using which we identified and derived the underlying relationships affecting the optical properties of the material. Elucidation of the complex interactions between the polymer structure, SWCNT chirality, and solvent characteristics gave rise to the formulation of a revised mechanism of solvatochromism in SWCNTs. The in-depth experimental and theoretical examination revealed that in the case of CP-solubilized SWCNTs, the solvatochromic shifts strictly depend on the assignment of individual chiral types to mods and families, which experience the strain exerted by the polymer chains in different ways.

Preparation and Application of Electrochemical Horseradish Peroxidase Sensor Based on a Black Phosphorene and Single-Walled Carbon Nanotubes Nanocomposite.

To design a new electrochemical horseradish peroxidase (HRP) biosensor with excellent analytical performance, black phosphorene (BP) nanosheets and single-walled carbon nanotubes (SWCNTs) nanocomposites were used as the modifier, with a carbon ionic liquid electrode (CILE) as the substrate electrode. The SWCNTs-BP nanocomposite was synthesized by a simple in situ mixing procedure and modified on the CILE surface by the direct casting method. Then HRP was immobilized on the modified electrode with Nafion film. The electrocatalysis of this electrochemical HRP biosensor to various targets was further explored. Experimental results indicated that the direct electrochemistry of HRP was realized with a pair of symmetric and quasi-reversible redox peaks appeared, which was due to the presence of SWCNTs-BP on the surface of CILE, exhibiting synergistic effects with high electrical conductivity and good biocompatibility. Excellent electrocatalytic activity to trichloroacetic acid (TCA), sodium nitrite (NaNO2), and hydrogen peroxide (H2O2) were realized, with a wide linear range and a low detection limit. Different real samples, such as a medical facial peel solution, the soak water of pickled vegetables, and a 3% H2O2 disinfectant, were further analyzed, with satisfactory results, further proving the potential practical applications for the electrochemical biosensor.

Toxicological assessment of functional polymer with single-walled carbon nanotubes in zebrafish embryos and its gill cell line.

Carbon nanotubes (CNTs) have been widely used in developing polymer hybrid coatings for anticorrosive application. In the present study, poly [(3,5-dimethyl-lH-pyrazole-1-yl) methyl methacrylate-co-glycidyl methacrylate] (PyM) was prepared by solution polymerization. Single-wall carbon nanotubes (SWCNT) were incorporated in the PyM by solution blending technique at different proportions. The PyM and its SWCNT (PyM-SWCNT) nanocomposites were characterized by FT-IR spectroscopy, X-Ray Diffraction, FE-SEM and HR-TEM. Different concentrations of PyM or PyM-SWCNT prepared in the present study were assessed separately for their toxicity by in vivo and in vitro assays using zebrafish embryos and gill cell line of zebrafish (DrG), respectively. The nanocomposites at the concentration of 400μgml-1 of PyM in 1.0% of SWCNT was found to be non-toxic and recommended for anticorrosive application whereas the nanocomposites with above 1% of SWCNT was found to be toxic. The nanocomposites with 1.5% of SWCNT delayed the hatching rate of eggs, decreased survival rate and heart beat in zebrafish embryos, and induced the morphological changes in DrG cells. Gene expression studies revealed that PyM-SWCNT with high concentration of SWCNT induced oxidative stress by activating ROS generations in zebrafish embryos and DrG cells. The immersion study of uncoated and coated with recommended concentration of PyM-SWCNT on mild steel (MS) in sea water was studied using FE-SEM and EDS, and the results showed effective corrosion protection without leaching behaviour. The nanocomposites with novel polymer in the present study may be used in the industry for anticorrosive purpose.

Non-noble metal FeMn and single-walled carbon nanotubes nanocomposites as effective bifunctional electrocatalysts in alkaline media for oxygen/hydrogen revolution reactions

Single-walled carbon nanotubes (SWCNTs) are one of electrochemical materials with excellent electrical properties. Herein, we design the new FeMn x /SWCNTs nanocomposites which are synthesized in one step by the direct current (DC) arc discharge method. The overpotentials of oxygen/hydrogen revolution reactions of FeMn 1 /SWCNTs electrodes in alkaline solution are 190 and 317 mV respectively when the current density reaches 10 mA cm −2 . The synergistic effect between FeMn compounds and single-walled carbon nanotubes can not only increase the active sites of the composites, but also optimize the electronic structure of the composites, thereby significantly improving the OER and HER performance of the materials. This work provides an idea that the composites of SWCNTs and bimetallic hybrids have excellent electrocatalytic performance.

An ultrasensitive high-performance baicalin sensor based on C3N4-SWCNTs/reduced graphene oxide/cyclodextrin metal-organic framework nanocomposite

Baicalin (Bn) obtained from natural plants has been found to exhibit significant antiviral activity against Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2). Herein, a novel ultrasensitive Bn electrochemical sensor was proposed based on graphitized carbon-nitride - single-walled carbon nanotube nanocomposites (C3N4-SWCNTs), reduced graphene oxide (rGO) and electrodeposited cyclodextrin-metal organic framework (CD-MOF). The sensing nanomaterials were characterized by X-ray diffraction spectroscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Under optimal conditions, the sensor exhibited sensitive detection of Bn in a wide linear range of 1 × 10-9–5 × 10-7 M with an LOD of 4.6 × 10-10 M and a sensitivity of 220 A/M, and it showed satisfactory stability and accuracy for detecting Bn in real samples (human serum and bear bile scutellaria eye drops). In addition, the electrochemical reaction sites and redox mechanism of Bn were revealed through electrochemical behavior and density functional theory. This work provided an insightful solution for detecting Bn, and extensive potential applications could be further expected.

Chromatic Conductive Polymer Nanocomposites of Poly (p-Phenylene Ethynylene)s and Single-Walled Carbon Nanotubes

We report on dispersions and thin films of chromatic conductive nanocomposites of poly(p-phenylene ethynylene)s (PPEs) and single-walled carbon nanotubes (SWNTs) generated via solution mixing. The linear, conjugated PPEs with dialkyl- and dialkyloxy-side chain groups are shown to debundle and disperse high concentration (up to 2.5 mg/mL) SWNTs in various organic solvents. The solubilization of SWNTs and PPE wrapping is accompanied with the change in the solution color. Ultraviolet visible absorption spectra of nanocomposite solutions demonstrate a new absorption peak at a higher wavelength, supporting the observed chromatism. Fluorescence spectra of nanocomposite solutions display significant quenching of the fluorescence intensity and the Stern–Volmer model is used to analyze fluorescence quenching. Electron microscopy of the chromatic solid films of high mass fraction PPE/SWNT nanocomposites obtained by vacuum filtration reveals the debundled SWNTs in the PPE matrix. The tensile strength and Young’s modulus of these PPE/SWNT nanocomposite films are as high as 150 MPa and 15 GPa, respectively. The composite films exhibit remarkably high conductivities, ranging from ~1000 S/m to ~10,000 S/m for 10 wt% and 60 wt% SWNT nanocomposites, respectively.

Effect of Humidity on the Electrical Properties of Poly (3, 4‐Ethylenedioxythiophene) – Poly (Styrenesulfonate) and its Carbon Nanotube Composites

AbstractWe report the effect of humidity on the electrical properties of different conductivity grades (low and high) of the polymer poly (3, 4‐ethylenedioxythiophene)‐poly (styrenesulfonate) (PEDOT : PSS) and their nanocomposites comprising of single walled carbon nanotubes (SWCNT). Polymer nanocomposites were prepared by using PEDOT : PSS with different weight ratio of chemically treated single walled carbon nanotubes (CT‐SWCNT). Humidity dependent change in resistance of thin films of pure and nanocomposites was measured and analyzed in detail. This basic study on the various conductivity grade PEDOT : PSS polymers and their SWCNT nanocomposites elucidate their response to humidity. It was found that the resistance of low and high conductivity grade pristine PEDOT : PSS films show opposite trends with respect to humidity. Interestingly these trends reverse in their nanocomposites containing CT‐SWCNT. The present study might find useful information for researchers working in the area of polymer nanocomposite based devices and applications.

Heterojunction formation between copper(II) oxide nanoparticles and single-walled carbon nanotubes to enhance antibacterial performance.

We delineate the excellent bactericidal efficacy of stable heterojunction nanocomposites composed of single-walled carbon nanotubes (SWCNTs) and copper(II) oxide (CuO) synthesized via facile recrystallization and calcination. The bactericidal effectiveness of the fabricated nanocomposites was examined using the standard broth-dilution method and the growth-inhibition-zone analysis method, in which bacteria cultured in an incubator in tryptic soy broth medium were subjected to the prepared samples. The bactericidal activity of all of the as-synthesized samples is evident in both methods, displaying a substantial decrease in bacterial colonies and resulting in clear inhibition zones, respectively. Among the CuO-SWCNT nanocomposites, the sample subjected to calcination at 500°C for 5h was found to exhibit the best performance against Staphylococcus aureus and Escherichia coli, forming inhibition zones 182% and 162% larger than those formed by pure CuO, respectively.

Pyrene-functionalized tetraphenylethylene polybenzoxazine for dispersing single-walled carbon nanotubes and energy storage

We synthesized the new pyrene-functionalized tetraphenylethylene benzoxazine monomer (TPEP-BZ) through 1,1,2,2-tetra(3-formyl-4-hydroxyphenyl)ethylene with 1-aminopyrene through Schiff base reaction, reduction with NaBH4 and then ring-closing with paraformaldehyde in a mixture of 1,4-dioxane and absolute EtOH. DSC, TGA, and FTIR spectroscopy were performed to understand the ring-opening polymerization and its corresponding thermal stability of this new TPEP-BZ monomer and then blending with different weight ratios of single-walled carbon nanotubes (SWCNT) before and after thermal treatments. More interestingly, the TPEP-BZ/SWCNT nanocomposites display lower curing temperature (262 °C), but significantly higher Td value (475 °C) and char yield (74 wt%) compared with typical Pa type benzoxazine. In addition, the poly (TPEP-BZ)/SWCNT nanocomposites also display high specific capacitance (84 F g−1) at a current density of 0.5 A g−1 and excellent cycling stability (98.3% capacitance retention over 2000 cycles).

Tailoring the electrically conductive network of injection-molded polymer-carbon nanotube composite at low filler content

Abstract Electrically conductive nano-fillers, such as carbon nanotubes (CNT), carbon black (CB) and carbon fibers (CF), have been of great interest to polymer scientists because their reinforcement into polymer matrices gives rise to conductive thermoplastics. However, it is found that their orientation distributions after the injection molding process reduce the interparticle contacts between particles and thus decreases the electrical conductivity. In this study, it is shown that electrically conductive networks can be re-tailored through post-processing annealing at a temperature higher than the glass-rubber transition temperature of the polymer. We demonstrate these results for polycarbonate (PC) composites produced by injection molding using different fillers including single-walled CNT (SWCNT), multi-walled CNT (MWCNT), CB and CF. The annealing-induced increase in the electrical network path is proved by electrical conductivity improvement. It can be explained by a transition from aligned, unconnected particles before annealing to an interconnected network after annealing through the viscoelastic relaxation of the polymer. Compared with CB- and CF-based PC composites, CNT-based PC composites at low contents exhibited outstanding conductivity improvement after isothermal annealing for several minutes. Moreover, the CNT network helps to keep the composite shape and strength after annealing. Especially, SWCNT nanocomposites have potential to rapid the tailoring process of the electrical network without significant size extension and strength reduction. The post-processing annealing may exploit the future applications of injection-molded CNT polymer composites.

Swelling and electrical properties of LLDPE reinforced by SWCNTs nanocomposites for radiation and sensors applications

Linear low-density polyethylene (LLDPE) incorporated with single-walled carbon nanotubes (SWCNTs) by mistreatment casting technique. The result of various weight percentage loadings of SWCNTs on the swelling and electrical properties of LLDPE/SWCNTs nanocomposite also γ-irradiation effects had been investigated. It was found that, at low concentration, it uniformly disperses into an LLDPE matrix and provides LLDPE/SWCNTs nanocomposites with abundant improved electrical properties by nine orders of magnitude. Positive temperature coefficient of conductivity (PTCC)/negative temperature coefficient of conductivity (NTCC) was affected by the SWCNT contents. Transmission electron microscopy and scanning electron microscope techniques were used to investigate the dispersion of SWCNTs in the LLDPE matrix. Linear exceptional modification within direct current electrical conduction of percolative threshold-loaded LLDPE as a perform of γ-irradiation dose will be used as a nontoxic, easy, inexpensive, and sensitive method to evaluate the irradiation dose in range 10 Gy–1 kGy also can be used in fabrication of firing sensors with various ranges of temperatures.

Potentially self-dopable poly(3-hexylthiophene) block copolymers/carbon nanotube nanocomposites for enhanced processibility and electrical properties

Development of new hole-transport layer (HTL) materials for organic photovoltaic (OPV) applications is one crucial issue to mitigate such limitations of low power efficiency, processibility, and stability derived from poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as a common HTL material. To this end, poly(3-hexylthiophene) (P3HT)-based diblock copolymers including the different ratios between polystyrene (PSty) or/and poly(neopentyl styrene sulfonate) (PNSS) as a second block segment were designed and then used for incorporating with single wall carbon nanotubes (SWCNTs) to form potentially self-dopable nanocomposites. The structure of fabricated P3HT-based diblock copolymer/SWCNT nanocomposites was examined by microscopic and spectroscopic characterizations, exhibiting a charge transfer behavior between P3HT and SWCNT, and growth of the P3HT crystalline phase along the SWCNT surface with a form of the conducting path. The acquired SWCNT nanocomposites exhibited good solubility and dispersion in various organic solvents including toluene, chlorobenzene, THF, chloroform, and DMF, which are good solvents for the PSty or/and PNSS neutral second block. The concept for the neutralized second block by protecting groups can prevent the poisoning ITO substrate by water contamination as shown in the conventional aqueous PEDOT-PSS solution. Notably, the PNSS constituent in the nanocomposite was merely acidified to give in-situ sulfonic acid groups in PSty by simple thermolysis process at 160 °C for 30 min after a solution process for fabrication of a thin film. The thermolysis step provided efficient doping of P3HT by PSS, in which the thiophene groups worked as Brønsted base are protonated by taking protons from sulfonic acid groups and then lead to a form of ionic bonds between cationic thiophene and anionic sulfonate groups. In addition, the formed ionic bonds in the nanocomposites led to an insoluble thin film, which has a good advantage for the further solvent process without substantial damages. The beneficial features of the conducting path along SWCNT and the efficient doping of P3HT by PSS in the acquired nanocomposites led to ca. 5-fold higher electrical conductivity (3.16 S cm−1) and similar work function (5.1 eV) in comparison to water contained commercial PEDOT:PSS (0.6 S cm−1 and 5.0 eV, respectively). As such, the rationally designed potentially self-dopable SWCNT nanocomposites can be one of the promising alternatives beyond the commercial PEDOT: PSS HTL material.

Spinel NiCo2O4 and single walled carbon nanotube nanocomposites for high performance supercapacitor application

In the present work, we report the hydrothermal synthesis of NiCo2O4/Single walled carbon nanotubes (SWNTs) nanocomposites for supercapacitor applications. The SWNTs provided the conductive network and favored the growth of NiCo2O4 nanoparticles on its surface to facilitate the collection and transportation of electrons during the electrochemical charge storage performance. Due to the improved conductivity and higher surface area of the NiCo2O4/SWNTs nanocomposites as compared to pure NiCo2O4 nanorods, it exhibited a specific capacitance of 1623 F/g and 1098 F/g at 1mV/s scan rate and 1A/g current density. Obtained energy density and power density of the NiCo2O4/SWNTs nanocomposites were 56.19 Wh/Kg and 9.824 kW/kg respectively. These results demonstrated that the nanocomposites could be a promising candidate for future high performance energy storage devices.

Micromechanical stick-slip model for characterizing damping responses of single-walled carbon nanotube nanocomposites

A micromechanical stick-slip model was developed to characterize the damping response of single-walled carbon nanotube nanocomposites. Depending on the strength of the interfacial bonding and the extent of applied loading, the single-walled carbon nanotube embedded in the matrix may either completely stick to the matrix or partially slide relative to the matrix. The slippage in the interface, together with the contact friction, may lead to the energy dissipation of single-walled carbon nanotube nanocomposites. The effects of the aspect ratio of single-walled carbon nanotube, interfacial bonding strength, volume fraction of single-walled carbon nanotube, and interfacial friction on the damping behavior of single-walled carbon nanotube nanocomposites were accounted for in the micromechanical stick-slip model. In order to validate the analytical model, the energy dissipation was also evaluated using the finite element method. A cylindrical finite element method, with an embedded single-walled carbon nanotube, was developed where the stick-slip behavior of the interface between the single-walled carbon nanotube and surrounding matrix was characterized using a contact element. It was found that the energy dissipation obtained from the finite element analysis agrees with that derived from the micromechanical stick-slip model. Moreover, the energy dissipation may significantly increase, when the single-walled carbon nanotube slippage takes place. The increment of the energy dissipation could be attributed to the interfacial contact friction between the single-walled carbon nanotube and the surround matrix as well as the viscoelastic properties of the matrix materials.