Single-mode Power Research Articles

Enhancing distance relay performance using wide-area protection for detecting symmetrical/unsymmetrical faults during power swings

The distance protection in transmission networks is vulnerable to malfunction during a power swing. Distance relays have a power swing blocking (PSB) function that prevents the relay from operating during a power swing. However, during a power swing, the relay will be able to identify and clear any fault. This paper offers a scheme for detecting symmetrical/unsymmetrical faults through power swing by estimating the maximum rate of change of a (ΔI-ΔV) ellipse circumference. The ellipse circumference of each phase is constructed at each power frequency cycle to consistently tracking the distinction in the measured current and voltage differences between the line's two ends. The main feature of the suggested work compared to previous works is the ability to detect numerous high impedance faults (HIFs) during single mode (slow/fast) power swing or multi-mode power swing in addition to the opportunity to detect faults during asymmetrical power swing. The suggested scheme is tested in a two-area, four-machine power system and tested also in the standard three-machine, nine-bus system using ATP software. The results reveal that the improved protective scheme performs well in fault conditions with and without power swing, and they confirm the scheme's suitability for interconnected networks.

High-power operations of single-mode surface grating long oxide aperture VCSELs

A high-power single-mode vertical cavity surface emitting laser (VCSEL) based on a slow light mode (SLM) concept is demonstrated. Shallow surface gratings were implemented to select a single slow light mode in mm long oxide aperture VCSELs. The vertical structure and well-established fabrication processes are unchanged from those of conventional 850 nm VCSELs. An electron-beam lithography is used to form a 1st-order shallow grating on the surface. Thanks to the low effective index and the intensity penetration of the SLM to the surface, the grating fabrication process is much easier than conventional guided mode distributed feedback lasers. A stable single mode with a high side suppression ration of more than 30 dB is obtained for the entire current range under CW operations. A narrow divergence of 0.038° in far field patterns is achieved for a 6 mm long device. A record single-mode power of more than 5 W is realized before saturation under 50 ns pulse operations. Unlike long cavity in-plane edge emitting lasers, a SLM-based VCSEL can provide higher output powers without limitation of catastrophic optical mirror damage. The high power, superior mode stability, and good beam quality of our unique design paves a way for VCSELs to be used for wide ranges of high-power applications.

High spectral purity GaSb-based blazed grating external cavity laser with tunable single-mode operation around 1940nm.

In this article, we present a tunable GaSb-based blazed grating external cavity laser (BG-ECL) with high spectral purity and high output power single-mode operation around 1940nm. The drastic increase in spectral selectivity and optical power results from the employment of a single-transverse-mode operating narrow ridge waveguide laser diode with an optimized AR coating on the front facet. The stable fundamental spatial mode output beam from the laser diode enables efficient collimation and high coupling efficiency with the blazed grating, leading to stronger wavelength-selective feedback. The AR coating with proper low reflectivity on the straight waveguide effectively suppresses the internal cavity mode lasing without causing extra optical loss. As a result, the BG-ECL device exhibits excellent comprehensive performance with a side mode suppression ratio (SMSR) over 50 dB with optical power exceeding 30 mW within a 70 nm tuning range. A maximum SMSR of 56.26 dB with 35.12 mW output power was observed in continuous-wave operation. By increasing the working temperature of the diode laser, the tuning range can be further extended to over 100 nm without noticeable degradation in spectral and output power performance.

KW-level monolithic single-mode narrow-linewidth all-solid photonic bandgap fiber amplifier.

Further power scaling of narrow-linewidth fiber lasers is critical for beam combining. Using all-solid photonic bandgap fibers with large effective mode areas and strong higher-order-mode suppression is an interesting approach. Previously, we demonstrated ∼400W single-frequency single-mode power at 1064 nm from a 50/400 photonic bandgap fiber amplifier, limited only by transverse mode instability (TMI). In this work, we demonstrate a TMI-limited single-mode power of 1.37 kW from a monolithic fiber amplifier with a 25/400 photonic bandgap fiber, the highest output power from a photonic bandgap fiber demonstrated to date, to the best of our knowledge. The spectral linewidth is broadened to ∼8GHz to suppress stimulated Brillouin scattering.

High power surface grating slow-light VCSEL

We report on a novel high power vertical cavity surface emitting laser (VCSEL) with high order shallow surface grating, which enables a single mode operation even for 6 mm long devices. A high single mode power of over 3 W is obtained under pulsed operations for a 6 mm long oxide aperture. A fan-shape beam with sub-degree narrow divergence is obtained up to high injection currents of 5 A. Thanks to the low effective index of slow-light modes in a VCSEL structure, the grating pitch is over 2.5 μm, which can be made by using a standard photo-lithography. The simple fabrication process and potentials of high power and high beam quality could make the proposed laser to be a good candidate for 3D optical sensing and imaging applications.

Fabrication and Characterization of Low-Threshold Single Fundamental Mode VCSELs With Dielectric DBR Mirror

The SiO <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> /SiN <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">x</sub> dielectric film stacks deposited by inductively coupled plasma chemical vapor deposition (ICP-CVD) are employed on the top of the oxide-confined vertical-cavity surface-emitting lasers (VCSELs). The reflecting mirror characteristics of the dielectric films are measured with varying numbers of pairs from 4 to 12. The prepared devices have low threshold current of 0.3 mA, single-mode peak power of 1.4 mW at room temperature. The thermal resistance of the device depending on ambient temperature is estimated according to the relationship of wavelength shift and dissipated power, allowing us to extract the actual temperature in active region and the temperature dependence of the output characteristics of the VCSEL. The beam property of the device is characterized by the far field pattern (FFP). Depending on the drive current, the average divergence angles of the output beam estimated from the full-width-half-maximum (FWHM) of the FFP varies between 20.4° and 21.2°. Furthermore, polarization-controlled single mode emission is achieved by introducing a built-in grating into the VCSEL with orthogonal polarization suppression ratio (OPSR) around 19 dB.

Surface grating VCSEL-integrated amplifier/beam scanner with high power and single mode operation

We propose and demonstrate a novel surface-grating vertical cavity surface emitting laser (VCSEL)-integrated amplifier/beam scanner. When the surface of the VCSEL section is periodically etched, a single slow-light mode which travels laterally into the amplifier section is selected due to the wavelength selectivity of the grating. The coupled slow light can be amplified with pumping the amplifier above the threshold. The far field angle of the amplified slow light can be continuously tuned through changing the pumping current at the VCSEL. We fabricated the integrated device with a 400 μm long VCSEL section and 1 mm long amplifier section, realizing in a single mode coupling power of over 7 mW and high output power of over 500 mW under pulsed operations of the amplifier. The continuous fan beam steering of 1.5° and a diffraction-limited narrow beam divergence of 0.06° are also achieved. We also fabricated device with extending the amplifier section length to 2 mm. A high single mode power of 1 W under pulsed operations is achieved, which is the record high power operation for single-mode VCSELs. With the performance of both high power and good beam quality, our new device shows great potential to be used as light source for LiDAR and other sensing applications.

Surface grating loaded VCSEL with single mode power of over 80 mW

Surface grating loaded VCSEL with single mode power of over 80 mW

Research on modelling and simulation of single-mode power split hybrid system

Aiming at an optimised single-mode compound power split hybrid system, the main operating mode of the hybrid system and the torque control strategy were developed in this paper. LMS/AMESim was used to establish the plant model of the vehicle as well as the key components of the hybrid system, while the vehicle control model was established in Matlab/Simulink. In addition, the fuel economy of a certain SUV under the NEDC road spectrum was simulated by the co-simulation model, and the simulation results were compared with the experimental results on the auto chassis dynamometer. The results demonstrated that the established simulation model is an accurate reflection of the physical reality under different road spectrum conditions. Application of the model can greatly reduce the difficulty of control strategy design and improve the efficiency of vehicle development.

Research on modelling and simulation of singlemode power split hybrid system

Aiming at an optimised single-mode compound power split hybrid system, the main operating mode of the hybrid system and the torque control strategy were developed in this paper. LMS/AMESim was used...

Влияние латерального оптического ограничения на характеристики вертикально-излучающих лазеров cпектрального диапазона 1.55 &amp;mu;m с заращенным туннельным переходом

The impact of transverse optical confinement on the static and spectral characteristics of 1.55 µm vertical-cavity surface-emitting lasers (WF-VCSEL) with a buried tunnel junction (BTJ) n++-InGaAs/р++-InAs/р++-InAlGaAs, implemented using molecular-beam epitaxy and wafer fusion. For lasers with a tunnel junction (TJ) etching depth of ~ 15 nm, it was found that the single-mode lasing occurs up to 8 μm BTJ mesa size due to a relatively weak lateral optical confinement, while the effect of a saturable absorber (SA) appears when the BTJ mesa size is less than 7 µm. Enhancing lateral optical confinement by increasing the BTJ etching depth up to ~ 20 nm leads to suppression of the SA effect at the BTJ mesa size of 5–6 µm, but at the same time limits the maximum single-mode optical power. According to the results of the analysis, an increase in the spectral mismatch between the maximum of the gain spectrum of the active region and the resonance wavelength of the WF-VCSEL up to ~35-50 nm will make it possible to suppress the undesirable SA effect in a wide range of the BTJ mesa sizes maintaining the single-mode lasing.

High-power, quasi-single-mode vertical-cavity surface-emitting laser with near-diffraction-limited and low-divergence beam

We report on a new type of high-power, single-mode vertical-cavity surface-emitting laser (VCSEL) based on the lasing of a slow-light mode laterally propagating in a long-apertured VCSEL structure. A VCSEL length of 500 μm produces high single-mode power with narrow beam divergence for sensing and 3D imaging applications. Slow-light modes show a lower threshold current and better beam quality. We found the optical resonance in the oxidized region at the end of a mesa helps when selecting a transverse mode. We obtained a quasi-single-mode power of 22 mW under continuous-wave operation. This result shows the possibility to achieve high single-mode power and high beam quality by introducing a mode selection mechanism.

Phase-locked pair of terahertz quantum cascade lasers through evanescent-wave coupling

A phase-locked laser pair containing two terahertz distributed feedback (DFB) quantum cascade lasers (QCLs) has been realized via evanescent-wave coupling. The mode selection in the laser pair is dominated by the waveguide loss which can be controlled mainly by the ridge width, as well as the width of the gap between the two ridges. A judicious design enables the laser pair to stably operate on the out-of-phase supermode with a side mode suppression ratio (SMSR) of 34 dB, a peak output power of 8.06 mW, and an amplification factor of about 1.72. Due to the significant overlap of the electromagnetic fields caused by the two laser elements, the laser pair is phase-locked even when the two elements are differently biased, confirmed by the measured emission spectra and far-field beam patterns. This work represents a crucial step towards phase-locked arrays for high power single-mode terahertz radiation.

302 W single-mode power from an Er/Yb fiber MOPA

There has been very little progress in the power scaling of Er/Yb fiber lasers in over a decade, reflecting the difficulties involved. Here we report, to the best of our knowledge, a new record of 302 W single-mode power from an Er/Yb fiber master oscillator power amplifier (MOPA) with a record optical efficiency of 56%, near the quantum limit. This is made possible by new fiber development from Nufern and off-resonant pumping of the Er/Yb fiber. We also show that further power scaling is no longer limited by ytterbium parasitic lasing but by fiber fuse in the Er/Yb fiber.

High power continuous wave operation of single mode quantum cascade lasers up to 5 W spanning λ∼3.8-8.3 µm.

In this work, we report high power continuous wave room-temperature operation single mode quantum cascade lasers in the mid-infrared spectral range from 3.8 to 8.3 µm. Single mode robustness and dynamic range are enhanced by optimizing the distributed feedback grating coupling design and the facet coatings. High power single mode operation is secured by circumventing the over-coupling issue and spatial hole burning effect. Maximum single-facet continuous-wave output power of 5.1 W and wall plug efficiency of 16.6% is achieved at room temperature. Single mode operation with a side mode suppression ratio of 30 dB and single-lobed far field with negligible beam steering is observed. The significantly increased power for single mode emission will boost the QCL applications in long-range free-space communication and remote sensing of hazardous chemicals.

Highly Efficient High-Brightness 970-nm Ridge Waveguide Lasers

In this letter we present new results on high power 970 nm ridge waveguide lasers based on an extreme double asymmetric epitaxial design. Due to an improved lateral-longitudinal design an M2-value below 1.1 and efficiency over 60% could be maintained at power levels slightly above 2 W. The lasers consist of a narrow mode-filter section at the back facet, a relatively broad section at the front facet for high power capability, and a tapered section in between with a very small taper-angle. We achieved the highest reported conversion efficiency for 1 W single lateral mode power to date of 67%, as well as the highest lateral (linear) brightness of 7.5 W/mm $\bullet$ mrad with 55% efficiency at 2.5 W. Results of first life time tests are presented which show the potential for commercial use.

A High Efficiency Multi-Mode Outphasing RF Power Amplifier With 31.6 dBm Peak Output Power in 45nm CMOS

A high efficiency multi-mode class-E outphasing RF power amplifier (PA) with a passive combining circuit is presented. The multi-mode PA combines multiple class-E amplifier branches and can work in different configurations. The PA improves efficiency at lower power levels by switching ‘on’ and ‘off’ individual branches in a static or dynamic manner and using Efficiency Enhancement Circuit (EEC). The proposed power amplifier is designed in 45nm CMOS technology. The PA delivers 31.6 dBm peak output power at 2.4 GHz with 49.2% drain efficiency in high power single level mode. With 64-QAM long-term evolution (LTE) signal with 10 MHz and 20 MHz bandwidth, −57 dBc and −53 dBc adjacent channel power ratio (ACPR) are obtained in single level outphasing (SLO) mode after digital pre-distortion (DPD). 25% and 33% average drain efficiency are achieved with LTE signal with 6 dB peak-to-average power ratio (PAPR) in single level outphasing and asymmetric multilevel outphasing (AMO) mode, respectively. The PA satisfies the spectral mask requirement of 802.11g WLAN signal with high margin. Error vector magnitude (EVM) of 1.1% (−39.36 dB) is obtained from the PA in single level outphasing high power mode after DPD with 64-QAM LTE signal with 10 MHz bandwidth.

Phase-locked two-color visible frequency comb system based on 1.5-μm all-polarization-maintaining fiber laser

A two-color visible frequency comb system based on a 1.5-μm all-polarization-maintaining (PM) fiber femtosecond laser was developed. This configuration relies on the implementation of three amplifiers, seeded by a single master oscillator. With the repetition rate (fr) of the oscillator locked to a reference frequency of 200 MHz, the output of the first amplifier was used to generate the feedback signal and achieve simultaneous phase lock of the carrier envelop offset frequency (fceo). The remaining two independently configurable amplifiers followed by highly nonlinear fibers and MgO-doped periodically poled lithium niobite crystals were used to produce visible comb lights at 543 and 633 nm (in air), respectively. By referencing to a hydrogen maser, the Allan deviations of fr and fceo at a gate time of 1 s are 438 μHz and 63 mHz, respectively. The spectral bandwidths of the 543- and 633-nm comb lights are 0.157 and 0.174 nm, respectively, and the single-mode powers of these comb lights are higher than 1 μW. The multiple-branch all-PM fiber-based visible frequency comb system exhibiting a narrow spectrum and a high single-mode power will facilitate the development of optical clocks and wavelength standard calibrations.

Single crystal diamond gain mirrors for high performance vertical external cavity surface emitting lasers

We report on the design, fabrication and optical performance of gain mirrors in single crystal diamond substrates for vertical external cavity surface emitting lasers (VECSELs). VECSELs have gained attention recently due to their potential for high emission power in single mode with low beam divergence, yet their maximum output power remains typically limited due to thermal roll-over resulting from insufficient heat dissipation. In order to increase the heat transfer, we exploit the excellent thermal conductivity of single crystal diamond, which is assembled in direct contact with the active structure. The optical cavity is hereby defined by an output coupler and a high reflection grating structure etched into the diamond surface. We here present the design and microfabrication of a diffraction grating that was optimized to reflect light into the 0th order, therefore combining the role of a gain mirror and a heatsink at the same time. Our process involved metal mask deposition onto the diamond surface, e-beam lithography and reactive ion etching. Characterization showed reflection above 95% at a center wavelength of 1550 nm, potentially allowing the integration of the diamond mirror into a vertical external cavity surface emitting laser.

47 W continuous-wave 1726 nm thulium fiber laser core-pumped by an erbium fiber laser.

The high-power, short-wavelength operation of a thulium-doped silica fiber laser at 1726nm has been demonstrated in a core-pumped monolithic (all-fiber) resonator configuration, in-band pumped by a high-power erbium-only fiber laser operating at 1580nm. The thulium fiber laser yielded 47W in a single-spatial-mode output beam for 60-W absorbed pump power. The corresponding slope efficiency, with respect to an absorbed pump power of 80%, compares favorably with the theoretical maximum (Stokes) efficiency of 91.5%. The prospects for further scaling of single-mode power in this wavelength regime to >100 W are considered, as well as the potential applications for high-power lasers operating in this difficult-to-reach wavelength band.