Single Hole Research Articles

Comparison of Outcomes and Recurrence Rates in Patients Undergoing Single or Double Burr Hole Surgery for the Treatment of Chronic Subdural Hematoma

Comparison of Outcomes and Recurrence Rates in Patients Undergoing Single or Double Burr Hole Surgery for the Treatment of Chronic Subdural Hematoma

Application of an Optimized Mechanism of Primary Reference Fuel to Single Hole Sprays

Application of an Optimized Mechanism of Primary Reference Fuel to Single Hole Sprays

Optimization of hole spacing for cut-top blasting based on new hole-sealing technology

In order to solve the problem of stress concentration on the roof of the mining trench, reduce the risk of sudden collapse of the roof overburden and disturbance, improve the control effect of the surrounding rock of the roof cutting and retaining roadway, and reduce the construction cost of mining tunnels, a new type of pouch sealing technology has been developed. By using on-site testing methods, the optimal sealing material ratio was optimized, and the crack propagation law and roof cutting effect of the 11503 W working face in Zhaizhen Coal Mine, Shandong Province were studied under hole spacing of 0.7, 1.0, and 1.1 meters and different sealing methods. The results show that using 1.5 m single pouch sealing technology in the blasting test, when the water cement ratio of the sealing material is 1:1, the required sealing strength and sealing temperature can be achieved, and there will be no punching phenomenon. When the spacing between holes is 1 m, the blasting effect is optimal, with a single hole effectively reaching a cutting seam length of about 0.5 m. There are obvious through cracks in the cave, with a total length of about 7 meters. After using the new pouch sealing technology for blasting, the displacement and bottom drum volume on both sides of the tunnel are lower than those of the traditional yellow mud sealing method, and the bottom drum volume is reduced by 37% and 53%, respectively. Based on comprehensive theoretical analysis and on-site experiments, the optimal hole spacing is determined to be 1 m, and the pouch sealing effect is good.

Rapid Manufacturing of Glass‐Based Digital Nucleic Acid Amplification Chips by Ultrafast Bessel Pulses

Advanced nucleic acid amplification techniques require separating test samples into numerous units (digitalization), which enables higher sensitivity and accuracy than traditional methods. Reagent partition tools are commercially available, but are usually complex and expensive, hindering mass adoption. Herein, the fabrication of a large‐scale micro‐through‐hole array on glass substrates for an advanced digital nucleic acid amplification technique (NAAT) is demonstrated. To meet the requirement of hole quantities (over tens of thousands) for valid nucleic acid statistics, ultrafast Bessel pulses with continuous translation of the glass substrate are applied. A single‐shot Bessel pulse can lead to a single hole, and 100 holes can be produced per second (scalable to thousands per second). Experiments using the fabricated chips show that the performance meets the NAAT requirements. This work provides a highly efficient and low‐cost scheme for reagent partitioning that promotes the wide accessibility of advanced digital NAATs as well as a variety of other applications.

Effect of CeO2 doping on structural, electrical and mechanical properties of basalt fibers

Developing basalt fibers with low dielectric properties and excellent water resistance is still very challenging. To overcome this problem, basalt glass and basalt fibers with different CeO2 content were prepared in this paper by using the conventional melt cooling method and single hole drawing process. The relationship between CeO2 content (0 wt%-4 wt%), the structural, electrical and mechanical properties of basalt fibers was investigated by using XRD, Raman, dielectric properties tester and fiber strength and elongation meter. The results showed that when the weight content of CeO2 was 2 wt%, the glass had the most stable network structure with the largest degree of linkage, resulting in a 75 % increase in water resistance, the lowest values of dielectric constant (6.25) and dielectric loss (4.38 × 10−3), and a 33 % increase in tensile strength.

Post-fire response of S235 steel plates considering different bolt hole-making processes

PurposeThis study aims at investigating the effect of bolt hole-making processes on the post-fire behavior of S235 steel plates.Design/methodology/approachA total of nine steel plates with a single bolt hole are tested. The single bolt holes are fabricated using three different hole-making processes: drilling, waterjet and plasma. Among the nine steel plates, three fabricated specimens are control specimens and are tested at ambient temperature. The six remaining steel plates with a single bolt hole are subjected to a complete heating-cooling cycle and then monotonically loaded until failure. The six fabricated specimens are first heated up to two different temperatures 800 and 925 °C, and then cooled back to the ambient prior to loading.FindingsThe results show that after being exposed to post-fire temperatures (800 and 925 °C), the maximum decrease in strength of the S235 steel plate was 6% (at 925 °C), 14% (at 925 °C) and 22% (at 800 °C) when compared to the results of ambient specimens for waterjet, drilled and plasma bolt holes, respectively. For post-fire temperature tests, drilled and waterjet bolt hole-making processes result in having approximately the same load-displacement response, and both have larger strength and ductility than those obtained using plasma cutting.Originality/valueThis study provides preliminary data to guide the steel designers and fabricators in choosing the most suitable hole-making process for fire applications and to quantify the post-fire reduction in capacity of S235 plates.

Efficacy of single burr hole with irrigation and sub-dural drain in the evacuation of chronic subdural hematoma

BackgroundChronic subdural hematoma (CSDH) remains one of the most common types of traumatic and spontaneous intracranial hematomas. The optimal method of treatment has not been definitely established. Surgical treatment options includes craniotomy, trephination, burrhole drainage and twist drill perforation. This study aimed at the evaluation of the clinical and radiological outcome after the efficacy of single burr hole with irrigation and sub-dural drain in the aim of successful evacuation of CSDH.ResultsA total of 53 patients were included in this study, the mean age of patients was 61.53 + 13.81 years. Results of the paired t test showed that the Glasgow coma scale has significantly improved by 0.89 points (p < 0.001) and that the average motor power has significantly improved for all individuals by 0.4 points (p = 0.043). We found that older aged patients have significantly less improvements in the postoperative motor power (r = − 0.317, p = 0.02) and require longer hospital stay (r = 0.32, p = 0.0197).ConclusionsA single burr hole with irrigation and leaving a subdural drain is safe procedure in managing subdural hematoma. We did not experience major adverse events related to drain insertion and efficient evacuation of collection and no obvious increase in mortality or morbidity rates.

Cholesteric Spherical Reflectors with Tunable Color from Single-Domain Cellulose Nanocrystal Microshells.

The wavelength- and polarization-selective Bragg reflection of visible light exhibited by films produced by drying cholesteric liquid crystal (CLC) suspensions of cellulose nanocrystals (CNCs) render these biosourced nanoparticles highly potent for many optical applications. While the conventionally produced films are flat, the CLC-derived helical CNC arrangement would acquire new powerful features if given spherical curvature. Drying CNC suspension droplets does not work, because the onset of kinetic arrest in droplets of anisotropic colloids leads to severe buckling and loss of spherical shape. Here, these problems are avoided by confining the CNC suspension in a spherical microshell surrounding an incompressible oil droplet. This prevents buckling, ensures strong helix pitch compression, and produces single-domain cholesteric spherical reflector particles with distinct visible color. Interestingly, the constrained shrinkage leads to spontaneous puncturing, leaving every particle with a single hole through which the inner oil phase can be extracted for recycling. By mixing two different CNC types at varying fractions, the retroreflection color is tuned throughout the visible spectrum. The new approach adds a versatile tool in the quest to utilize bioderived CLCs, enabling spherically curved particles with the same excellent optical quality and smooth surface as previously obtained only in flat films.

Brain Abscess: A Comparison of Surgical Outcomes between Conventional Burr Hole Aspiration and Endoscope-assisted Evacuation.

Brain abscess is a major health problem with a significant morbidity and mortality rate. The objective of this study was to compare the surgical efficacy between endoscope-assisted evacuations of brain abscess with a single burr hole aspiration procedure in a tertiary health care center. This single center non-randomized clinical study was conducted in our Department of Neurosurgery during the period of July 2020 to December 2021. Patients under 30 years of age of both genders presented with brain abscess were enrolled in this study. Patients were treated with two different techniques and divided into 2 groups: conventional burr hole aspiration group and endoscope-assisted evacuation group. Thirty patients were enrolled for this study. The mean age was 13.0 ± 6.3 years in burr hole group and is 13.1 ± 6.4 years in endoscope-assisted group. This study showed ≥75.0% evacuation of brain abscess at 1st post-operative day in 13 (92.9%) patients in endoscope-assisted group and 5 (33.3%) patients in burr hole group. This study showed mortality rate of 6.7% in both the groups. Mean residual volume at 30th post-operative day was 0.75 ml in endoscope-assisted group and 1.75 ml in burr hole aspiration group. No patients treated with required endoscope-assisted evacuation required a repeated surgery, whereas 5 patients (33.3%) of patients treated with conventional burr hole required it. This study showed that endoscope-assisted procedure has better rate of abscess evacuation, less chance of residual and repeated surgeries than conventional burr hole.

Spray Momentum Flux Novel Estimation Procedure through the Fuel Rate of Injection Using Hydrogenated Fuels with Single Hole Nozzle Diesel Injector.

Sustainable means of transport require the innovation or development of propulsive systems more respectful of the environment. Despite current criticism, modern compression-ignition engines are efficient alternatives also in light aviation and surveillance drones (such as small helicopters), as means of air transport. Currently, the improvement of the injection, air-fuel mixture formation, and combustion processes using sustainable synthetic fuels, produced from renewable raw materials or by carbon dioxide capture, is a reality. For improving the air-fuel mixture formation inside the combustion chamber, one of the key parameters is knowledge of the spray momentum flux because of its effect on the air entrainement. To measure this parameter is complex. However, the experimental determination of the fuel mass flow rate is a common procedure. The objective of this work is the proposal of a novel but robust methodology for the momentum flux estimation of fuel sprays from measurement of the rate of injection. In this work, single-hole nozzles of 115, 130, and 150 μm in diameter are studied. The implemented methodology is applied to three fuels: a diesel fuel without biodiesel, used as reference, and two sustainable synthetic fuels: a gas to liquid fuel and a hydrotreated vegetable oil. With the fuel injection rates and the simple model proposed, the spray momentum flux is estimated under different operating conditions of a common-rail injection system. The results of the spray momentum flux show a very good precision compared with those experimentally and previously obtained with similar fuels but with multihole nozzle. With the method proposed in this work, an adequate forecast of spray momentum flux is obtained in the case of not having an experimental setup that allows direct measurement of the momentum flux. This study can help investigators for fuel spray modeling with novel and renewable fuels in modern propulsive systems.

Modified orbitozygomatic craniotomy with a single burr hole in the alternative sphenoid ridge keyhole

BackgroundOne-piece modified orbitozygomatic approach (OZA) is an extended version of the pterional approach that also includes orbital walls and frontal process of the zygomatic bone. For this craniotomy one burr hole must be placed in MacCarty keyhole and another - in the temporal region. ObjectiveTo develop a technique of the one-piece modified OZA with single a burr hole in the alternative sphenoid ridge keyhole that allows access to orbit, anterior cranial fossa and middle cranial fossa and apply it intraoperatively. MethodsA single human head specimen was used. The dissection was performed using standard surgical instruments high-speed Stryker drill. Every stage of the approach was photographed. We also report a surgical case of a patient with orbital cavernous hemangioma that was resected using the described technique. ResultsThe technique of the one-piece modified OZA with a single burr hole in the alternative sphenoid ridge keyhole is described, and its advantages and limitations are analyzed. The technique is used to totally resect an orbital cavernous hemangioma with good functional and cosmetic result. ConclusionModified OZA with a single burr hole in the sphenoid ridge keyhole is possible and may be an alternative to the classic technique. The advantages of this variation are the placement of just one burr hole and the preservation of a larger portion of the orbital roof. The latter facilitates better bone reconstruction and better cosmetic outcome. Disadvantages are the difficulty of identifying the location of the sphenoid ridge keyhole and risk of damaging the dura.

Neuroendoscopic transventricular transchoroidal approach for access to the posterior zone of the third ventricle or pineal region.

The endoscopic transventricular transchoroidal approach facilitates entry into the posterior part of the third ventricle, allowing a visualization field from the foramen of Monro to the pineal region through this anatomical corridor. Combined surgery to treat the target lesion and possible endoscopic third ventriculostomy (ETV) can be performed through a single burr hole. A detailed description of this surgical technique is given, and a series of cases from our center is presented. This retrospective study included patients with lesions in the pineal region or posterior zone of the third ventricle who underwent surgery between 2004 and 2022 in our center for tumor biopsy or endoscopic cyst fenestration. In nine cases, the transchoroidal approach was performed. Demographic and clinical variables were collected: sex, age at diagnosis, clinical presentation, characteristics of the lesion, pathological diagnosis, characteristics of the procedure, complications, subsequent treatments, evolution, follow-up time, and degree of success of the endoscopic procedure. The mean and range of the quantitative variables and frequency of the qualitative variables were analyzed, together with the statistical significance (p < 0.05). Surgical planning was carried out by performing a preoperative MRI, calculating the ideal entry point and trajectory for each case. The preoperative planning of the surgical technique is described in detail. Of our sample, 55.6% were women, with a mean age of 35years (7-78). The most common clinical presentation was intracranial hypertension (55.6%), with or without a focus. Eight patients presented hydrocephalus at diagnosis. The most frequent procedure was endoscopic biopsy with ETV (66.7%). The pathological diagnosis varied widely. Procedure-related complications included one case of self-limited bleeding of the choroidal fissure at its opening and one intraventricular hemorrhage due to tumor bleeding in the postoperative period. Non-procedure-related complications comprised two ETV failures and one case of systemic infection, while late complications included one case of disease progression and one case of radionecrosis. Four patients died, one due to poor neurological evolution after post-surgical tumor bleeding and three due to causes unrelated to the procedure. The rest of the patients had a favorable evolution and were asymptomatic or stable. The transchoroidal approach through a single burr hole is a feasible and safe option for access to the posterior part of the third ventricle. Proper planning of each case is necessary to avoid complications.

A new proof of the Riemannian Penrose inequality

We give an overview of our recent new proof of the Riemannian Penrose inequality in the case of a single black hole. The proof is based on a new monotonicity formula, holding along the level sets of the p -capacitary potential of the connected boundary of an asymptotically flat 3 -manifold, with nonnegative scalar curvature.

Astronomically‐Paced Changes in Paleoproductivity, Winnowing, and Mineral Flux Over Broken Ridge (Indian Ocean) Since the Early Miocene

AbstractA significant shift in Earth's climate characterizes the Neogene, transitioning from a single‐ice‐sheet planet to the current bipolar configuration. This climate evolution is closely linked to changing ocean currents, but globally‐distributed continuous high‐resolution sedimentary records are needed to fully capture this interaction. The Ocean Drilling Program (ODP) Site 752, located on Broken Ridge in the Indian Ocean, provides such a Miocene‐to‐recent archive. We use X‐ray fluorescence (XRF) core scanning to build an eccentricity‐tuned age‐depth model and reconstruct paleoceanographic changes since 23 Ma. We find two intervals of enhanced productivity, during the early and middle Miocene (18.5–13.7 Ma) and late Pliocene/early Pleistocene (3–1 Ma). We also report a mixed eccentricity‐obliquity imprint in the XRF‐derived paleoproductivity proxy. In terms of grain size, three coarsening steps occur between 19.2–16 Ma, 10.8–8 Ma, and since 2.6 Ma. The steps respectively indicate stronger current winnowing in response to vigorous Antarctic Intermediate Water flow over Broken Ridge in the early Miocene, the first transient onset of Tasman Leakage in the Late Miocene, and the intensification of global oceanic circulation at the Plio‐Pleistocene transition. High‐resolution iron and manganese series provide a detailed Neogene dust record. This study utilized a single hole from an ODP legacy‐site. Nevertheless, we managed to provide novel perspectives on past Indian Ocean responses to astronomical forcing. We conclude that Neogene sediments from Broken Ridge harbor the potential for even more comprehensive reconstructions. Realizing this potential necessitates re‐drilling of these sedimentary archives utilizing modern drilling strategies.

Modelling and evaluation of the post-hardness and forming limit diagram in the single point incremental hole flanging (SPIHF) process using ANN, FEM and experimental

In the single point incremental hole flanging (SPIHF) process, a sheet material with pre-cut holes is deformed using the SPIF technique to generate a flange, making it an effective approach for low volume manufacturing and quick prototyping. In the case of the SPIHF technique, the post-forming hardness property, the forming limit diagram (FLD), and spring-back phenomena are not completely evaluated. To this end, this paper employs experimental investigation and numerical validation to analyse the impact of SPIHF process parameters like tool diameter, feed rate, spindle speed, and initial hole diameter on these aspects for the truncated incrementally formed components made from AA1060 aluminium alloy and DC01 carbon steel. The plasticity behaviour of both sheet metals was simulated using the Workbench LS-DYNA model and ANSYS software version 18. Additionally, Cowper Symonds power-law hardening was added to the model to account for material properties. The average post-hardness of AA1060 and DC01 was evaluated using an SPIHF prediction model based on the performance of an artificial neural network (ANN). This ANN model was developed using a feed-forward back-propagation network trained using the Levenberg-Marquardt approach. The ANNs 4-n-1 were created by varying the transfer functions and the number of hidden neurons. Greater spindle speed and bigger pre-cut holes were shown to significantly increase the post-formed hardness of the truncated components, whereas the converse was seen when using a higher feed rate and a larger tool diameter. In addition, the FLD and spring-back improved dramatically with larger hole diameters. Employing correlation coefficient (R) and mean square error (MSE) as validation measures, it was shown that the established ANN models accurately predicted the SPIHF process response. Both the DC01 and AA1060 neural network models with a 4-8-1 network architecture performed very well, with MSE and R values of 0.0000105 and 1 for DC01 and 0.02613 and 0.99982 for AA1061.

Topological and high-performance nonreciprocal extraordinary optical transmission from a guided mode to free-space radiation

Extraordinary optical transmission (EOT) is a hallmark of surface plasmons and a precursor to nanoplasmonics and metamaterials. However, to the best of our knowledge, this effect has never been topologically protected in three dimensions, leaving it vulnerable to structural imperfections, nonlocal effects, and backreflections. We report broadband, three-dimensional unidirectional structures that allow for EOT (normalized transmission > 1) through deep-subdiffractional single holes, immune to these deleterious effects. These structures avoid unnecessary propagation losses and achieve maximum transmission through a single hole, limited only by unavoidable dissipative losses. In the limit of vanishing losses, the transmission through a deep-subdiffractional hole can approach unity, significantly surpassing existing devices, and rivaling the performance of negative-index ‘perfect’ lenses. The topological stability of these structures renders them robust against surface roughness, defects, and nonlocality, without the need for elaborate meta-structures or tapering.

Factors for predicting recurrence after burr hole drainage for chronic subdural hematoma: a retrospective study.

Chronic subdural hematoma (SDH) is a common disease in the neurosurgical field, and hematoma drainage through burr hole trephination has been widely considered the optimal treatment for SDH. Despite numerous investigations aimed at predicting recurrence rates and associated factors, studies have demonstrated inconsistent results. In this study, we aimed to comprehensively determine the predictive factors of chronic SDH recurrence in surgically treated patients. We retrospectively evaluated 578 consecutive patients who underwent single burr hole surgery for chronic SDH at our institute between January 2008 and December 2021. Various clinical and radiological factors in patients with and without recurrence were compared using univariate and multivariate logistic regression analyses. A total of 438 patients (531 hemispheres) were analyzed. Fifty-four (10.17%) of the 531 hemispheres had recurrence of chronic SDH within 6months. Male sex (adjusted odds ratio (aOR) = 3.48; 95% confidence interval (CI), 1.42-8.49), bilateral hematomas (aOR = 2.14; 95% CI, 1.05-4.35), laminar hematoma type (aOR = 2.87; 95% CI, 1.23-6.71), > 30-cm3 volume of postoperative residual hematoma (aOR = 2.99; 95% CI, 1.01-8.83), and preoperative blood glucose level of ≥ 150mg/dL (aOR = 2.11; 95% CI, 1.10-4.05) were identified as independent factors associated with recurrence in multivariate logistic regression analysis. The present study revealed that male patients and those who had bilateral hematomas, laminar hematoma type, a large volume of hematoma after surgery, and a high preoperative blood glucose level had a higher probability of experiencing recurrent chronic SDH. We recommend close monitoring of patients 6months postoperatively to detect subsequent chronic SDH recurrence.

Cold-formed stainless steel beams with single web hole at elevated temperatures

Steel structures are often used in buildings due to their advantage in weight-to-strength ratio. However, their structural capacity deteriorates in fire as the temperature of the structures rises. Investigation of cold-formed stainless steel (CFSS) structures at elevated temperatures is still limited, especially for rectangular hollow section (RHS) beams having a single web hole in the mid-span (perforated web). Therefore, a numerical investigation was conducted to evaluate the current design provisions to calculate the strength of such beams at elevated temperatures ranging from 22 - 900 °C. A total of 400 specimens of stainless steel grades austenitic (EN 1.4301) and lean duplex (EN 1.4162) were considered. The investigation used finite element analysis (FEA) to simulate the behaviour of RHS beams with perforated web under pure bending. The finite element (FE) model was validated against a series of experimental results available in literature. The comparison between flexural strengths obtained from FEA with design values calculated from the current design rules showed that the design rules are conservative. However, they are not always reliable and safe for RHS beams without and with a perforated web for the two material grades at elevated temperatures. In this study, only the design rules specified by Eurocode 3 are shown to be reliable and safe.

Buckling analysis of thin plates with circular cut-outs for sustainable ventilated food packaging design

Thin plates with circular cut-outs are widely used in engineering structures such as bridges, construction, and ventilated corrugated paperboard boxes in food packaging. This study investigates the critical buckling loads of thin elastic plates comprised of a single circular hole at different locations and with different sizes. To determine the critical loads, experimental tests and finite element method simulations are conducted. The vertical location and the diameter of the hole impact the buckling results significantly. The results indicate a significant correlation between the experimental and finite element data. The study develops second and third order polynomial formulas that predict buckling loads. In this study, corrugated paperboard plates were used as samples to gain insights into ventilated food packaging designs, aiming to enhance their buckling strength while reducing packaging material consumption for packaging sustainability purposes. The solution proposed in this study can be applied to predict the buckling of other elastic thin plate structures with a circular hole, relevant to industries such as construction and aerospace.

Gas Evolution Principle during Gas Drainage from a Drill Hole along the Coal Seam and Reasonable Borehole Layout Spacing.

The efficiency of coal seam gas drainage can be further improved by the accurate mastery of the gas evolution principle during gas drainage from the drill hole along the coal seam and reasonable optimization of borehole layout spacing. Based on the actual geological conditions of the no. 2 coal seam in a coal mine in Guizhou, China, and relevant control equations, a fluid-structure interaction model of gas drainage from a drill hole along the coal seam was established in this paper. Besides, numerical simulation research on the gas evolution principle during gas drainage along the coal seam and optimization of the borehole layout spacing was carried out with the COMSOL simulation software; and these were verified in combination with the project site. The results showed that in the early stage of gas drainage the gas pressure in the area near the drill holes decreased significantly. As the gas drainage went on, the degree of influence decreased gradually. During the gas drainage from adjacent drill holes, the gas pressure in the coal body between the holes decreased rapidly, and the migration was obvious. With the increase of the spacing between the drill holes, the drainage superposition effect between these holes gradually decreased until the influence area around a single hole is independently distributed in a circle-like shape, indicating that the optimization and the reasonable spacing of the drill holes are directly related to the effect of the gas drainage. With the increase of drilling spacing, the superposition effect of extraction between the holes gradually decreased until the influence area around a single hole is independently distributed in the shape of a circle, indicating that the optimization of drilling spacing is directly related to the effect of gas drainage. The results of numerical simulation were verified by analyzing the three-dimensional map of the gas pressure during the period of gas drainage at the project site and by comparing and examining the rational borehole layout spacing of the drill hole along the coal seam. The results of this study can be used to determine the spacing of gas extraction boreholes and improve the efficiency of gas extraction in the no. 2 coal seam of a coal mine in Guizhou, China, as well as to provide a reference for the gas pressure evolution, velocity field distribution, the prediction of effective drainage area, and the selection of rational borehole layout spacing during gas drainage.