Single-cylinder Research Engine Research Articles

The criteria for qualifying fuels as a replacement fuels for internal combustion engines

The article presents the classification of motor fuels into conventional and unconventional. The concept of replacement fuels is formalized as fuels that can replace conventional petroleum fuels for spark ignition and self-ignition engines without any structural or regulatory changes. The criteria for qualification unconventional fuels as replacement fuels are presented. This article also introduces the results of empirical research conducted on a single-cylinder research engine powered by diesel fuel and rapeseed methyl esters (RME) in summer version and winter version. The engine was tested and the combustion phenomenon in the cylinder was analyzed. Very similar engine properties were observed for diesel fuel and rapeseed methyl esters (RME) in the summer version, while greater differences were found for rapeseed methyl esters (RME) with winter additives. In light of the empirical research and the physicochemical properties of the fuels, it is concluded that RME warrants consideration as replacement fuel for engines with self-ignition, especially in the case of biofuel in the summer version.

Numerical and experimental analysis of the combustion in a Single-Cylinder research engine with passive TJI pre-chamber operating with hydrated ethanol

Advanced ignition systems, such as turbulent jet ignition, have the capacity to improve the combustion process of internal combustion engines, increasing fuel conversion efficiency and reducing emissions, especially when applied with ethanol biofuel. Technologies that take advantage of the local energy potential, taking into account the geographic, demographic and social characteristics of each country, increase the diversity of solutions for the sustainable future of the transport sector. The present work aims to develop a system with a passive pre-chamber operating in turbulent jet ignition mode, applied to a single-cylinder research engine with a stoichiometric air–fuel mixture of ethanol. Numerical simulations were carried out and experimentally validated applying the commercial software CONVERGE CFD. The results showed that the optimized configuration presented higher fuel conversion efficiency, when compared to conventional spark ignition, thus producing greater savings per kilometer driven and lessing the dependence on fossil fuels. The pre-chambers with both lateral holes and a central hole showed a maximum NOx reduction of 5.9 g/kWh, reducing the second half of combustion by 6.2 crank angle degrees and the first half of combustion by up to 1.8 crank angle degrees compared to SI. This indicates a potential for increasing the compression ratio for pre-chamber configurations without the occurrence of knock. Furthermore, there is a direct relationship between the quenching of the jets after exiting the pre-chamber holes and turbulence, with quenching occurring when turbulent kinetic energy was greater than 15000 m2/s2.

Optical study on a heavy-duty natural gas dual-fuel engine applying POMDME as pilot fuel

In this study, a fully optically accessible single-cylinder research engine is the basis for the visualization and generation of extensive knowledge about the in-cylinder processes of mixture formation, ignition, and combustion of alternative fuels for the dual-fuel combustion process. POMDME substitutes the fossil pilot fuel as a drop-in, non-sooting alternative to widely eliminate the NOx-PM tradeoff. Furthermore, an optimized ignition behavior, increased degrees of freedom in combustion phasing, and the pilot’s energy content are expected. The flame luminosity transmitted via an optical piston was split in the optical path to record the natural flame luminosity simultaneously with an RGB high-speed camera. The second channel consisted of OH chemiluminescence recording, isolated by a bandpass filter via an intensified monochrome high-speed camera. To investigate the combustion process spectrally, spatially, and temporally resolved in more detail, selected operating points were re-recorded via a high-speed imaging spectrograph. POMDME is benchmarked against regular diesel oil, according to EN590. Synthetic natural gas is applied as the primary gaseous fuel. Experimental sweeps along the overall pilot’s energy content (2%, 5%, 10%), injection pressure (500–1600 bar), and start of energizing (5–55 CAD bFTDC) are carried out. The given conditions result in decreased liquid-penetration length between 25% and 30% for the oxygenate, larger for earlier SOE and higher dilution. The lift-off length is nearer the liquid penetration length, increasing for higher rail pressures. The light-based ignition delay for EN590 is enlarged by 0.8 CAD after adding methane, while the oxygenate is not visibly retarded. Without methane, the oxygenate preceded EN590 by 0.6 CAD. The temporal and spatial position and extent of premixed, diffusive, and OH*, change significantly. RCCI operation at practically relevant 18.4 bar IMEP is demonstrated, highlighting the influence of the start of energizing variation with 51% decreased burn duration in the first half of combustion.

Methods and metrics to assess the accuracy of heat flux data from a spark ignition IC engine

The measurement of in-cylinder heat transfer can be a valuable diagnostic tool for quantifying and improving IC engine performance. Increased heat transfer out of the combustion chamber negatively impacts overall efficiency, while heat transfer from the metal to the charge can increase knock propensity. The heat flux at various locations in an engine cylinder can be measured using heat flux probes consisting of two thermocouples – a surface thermocouple exposed to the changing in-cylinder temperatures, and a far field thermocouple which has a constant temperature at steady state operating conditions. The buildup of carbon deposits on the surface thermocouple can affect the heat flux measurements and lead to errors in the data. Heat flux measurements were performed on a proprietary single-cylinder research engine with instrumented heat flux probes in the cylinder head and cylinder liner. The engine was run rich with a high PMI fuel to expedite the buildup of carbon deposits. A metric was developed based on the output of the surface thermocouple to determine the cleanliness of the heat flux probes non-intrusively. Heat flux calculations were done using the FFT method and validated using the Cook-Felderman method. An uncertainty analysis was conducted on the heat flux data to verify that the negative heat flux observed was not due to errors in the distance between the two thermocouples or the measurement of temperature. Finally, to bolster confidence in the results, heat flux measurements were made for motoring conditions with varying coolant and intake air temperatures to gauge whether the trends in the output were in the expected direction.

Analysis of Hydrogen Combustion in a Spark Ignition Research Engine with a Barrier Discharge Igniter

Hydrogen fuel is gaining particular attention in internal combustion engines. In addition to zero-carbon emissions, major advantages relate to its combustion characteristics, which allow a significant increase in thermal efficiency under ultra-lean operation and with very low NOx levels. The ignition system is one of the main technology enablers, as it determines the capability to control ultra-lean operations, avoid backfire phenomena, and/or reduce the risks of abnormal combustions. The latter results from hydrogen’s low ignition energy and it is associated with factors like high-temperature residuals, hot spots, and irregular spark plug discharge. The ACIS gen 2-Barrier Discharge Igniter excels in accelerating the initial flame growth speed by the generation of non-equilibrium low-temperature plasma, a strong ignition promoter for the combined action of kinetic and thermal effects. Moreover, its volumetric discharge facilitates combustion initiation on a wide region, in contrast to the localized ignition of traditional spark systems. In this work we present for the first time, to the best of our knowledge, experimental results showing the performance of a hydrogen engine with a low-temperature plasma discharge. Tests were conducted on a single-cylinder research engine, achieving ultra-lean conditions with cycle-to-cycle variability results below 2.5%. The analysis indicates that the H2-BDI combined solution is capable of accelerating the evolution of the flame front compared to traditional spark plugs, leading to a significant reduction in the cycle-to-cycle variability. A meticulous adjustment of the BDI control parameters further enhances igniter performance and contributes to a deeper understanding of the innovative approach proposed in this study.

The Synergy between Methanol M100 and Plasma-Assisted Ignition System PAI to Achieve Increasingly Leaner Mixtures in a Single-Cylinder Engine

Currently, conventional spark–ignition engines face challenges in meeting the ever-growing demands of customers and increasingly stringent regulations regarding pollutant emissions. A combination of innovative strategies and carbon-neutral fuels is deemed necessary in order to further reduce fuel consumption and minimize engine emissions. The present work aims to assess the performance of combustion strategies using low-carbon-content fuel, such as methanol M100, ignited by a plasma-assisted igniter (PAI) under ultra-lean conditions. The experimental campaign is conducted on a single-cylinder research engine at 1000 rpm and low loads, moving up to the engine lean stable limits. The specific purpose of this work is to determine the benefits brought by the proposed strategy, referred to as M100–PAI, which compared market gasoline E5 ignited by the PAI system and conventional spark. The synergy between M100 (methanol) and Plasma-Assisted Ignition (PAI) in internal combustion engines yielded notable benefits. This combination significantly improved combustion stability if compared to the other combinations tested, by extending the lean stable limit to λ = 2.0, reducing cycle-to-cycle variability, and facilitating faster flame front acceleration, resulting in enhanced homogeneity. These enhancements, obtained with the combination M100–PAI, contributed to higher fuel efficiency, showing a 10% efficiency gain over the combination E5–gasoline spark ignition. The findings highlight the potential of innovative combustion strategies using low-carbon fuels and advanced ignition systems to meet stringent emissions regulations while improving engine performance.

Combustion and specific fuel consumption evaluation of a single-cylinder engine fueled with ethanol, gasoline, and a hydrogen-rich mixture

This study evaluates the effects of adding a hydrogen gaseous mixture (HGM) to primary fuel in a single cylinder research engine (SCRE). Storage and transportation of high-purity hydrogen limit the application of this gas. With the development of fuel reforming methods, using hydrogen-enriched mixtures in spark-ignited internal combustion engines is a convenient option to fossil fuels. Ethanol and gasoline were used as primary fuel by direct injection (DI), and gaseous mixture was added by fumigation system (FS). The experimental analysis was developed in Spark Ignition (SI) four-stroke engine 4 valves and 0.45 L of cubic capacity. For each operation condition and primary fuel, spark timing and amount of HGM were adjusted in order to keep air-fuel ratio stochiometric (λ = 1,00). However, the spark timing and the percentage of gas varied, aiming to evaluate the behavior of the air-fuel mixture. It was evaluated the specific fuel consumption and the evolution of the combustion process. The results showed that the addition of reformed gas promotes acceleration of the combustion process ethanol and gasoline. Results were expressive when using ethanol. A reduction in fuel-specific consumption - for this fuel - with combustion centralized, which did not occur when gasoline was employed.

Evaluation of ammonia-gasoline co-combustion in a modern spark ignition research engine

Ammonia (NH3) is emerging as a potential favoured fuel for longer range decarbonised heavy transport, particularly in the marine sector, predominantly due to highly favourable characteristics as an effective hydrogen carrier. This is despite generally unfavourable combustion and toxicity attributes, restricting end use to applications where robust health and safety protocols can always be upheld. In the currently reported work, a spark ignited thermodynamic single cylinder research engine equipped with gasoline direct injection was upgraded to include gaseous ammonia port injection fuelling, with the aim of understanding maximum viable ammonia substitution ratios across the speed-load operating map. The work was conducted at varied effective compression ratios under overall stoichiometric conditions, with the spark timing re-optimised for maximum brake torque at all stable logged sites. The experiments included industry standard measurements of combustion, performance, and engine-out emissions (including NH3 “slip”). With a geometric compression ratio of 11.2:1, it was found possible to run the engine on pure ammonia at low engine speeds (1000-1800 rpm) and loads of 12 bar net IMEP. When progressively dropping down below this load limit an increasing amount of gasoline co-firing was required to avoid engine misfire. When operating at 1800 rpm and 12 bar net IMEP, all emissions of carbon (CO2, CO, unburned hydrocarbons) and NOx decreased considerably when switching to higher NH3 substitution ratios, with NOx reduced by ~ 45% at 1800 rpm/12 bar when switching from pure gasoline to pure NH3 (associated with longer and cooler combustion). By further increasing the geometric compression ratio to 12.4 and reducing the intake camshaft duration for maximum effective compression ratio, it was possible to operate the engine on pure ammonia at much lower loads in a fully warmed up state (e.g., linear low load limit line from 1000 rpm/6 bar net IMEP to 1800 rpm/9 bar net IMEP). Under all conditions, the indicated thermal efficiency of the engine was either equivalent to or slightly higher than that obtained using gasoline-only due to the favourable anti-knock rating of NH3. Ongoing work is concerned with detailed breakdown of individual NOx species together with measuring the impact of hydrogen enrichment across the operating map.

Frictional Losses of Ring Pack in SI and HCCI Engine

The vast majority of research dedicated to enhancing the homogenous charge compression ignition (HCCI) low-temperature combustion system is focused on improving controllability, efficiency and emissions. This article aims to assess the impact of HCCI combustion on the operation of the piston ring system. Utilizing the measured pressures in the combustion chamber of a single-cylinder research engine operating in spark ignition (SI) and HCCI modes at various loads, simulations were carried out using an advanced ring pack model. This model integrates the gas flow, ring dynamics and ring mixed lubrication models. Simulations revealed that differences in the pressure above the piston between the HCCI and SI combustion significantly influence ring pack performance. The predicted energy losses due to the friction of piston rings against the cylinder liner are up to 5% higher in the HCCI engine than in the SI engine. This identified drawback diminishes the advantages of the HCCI engine resulting from higher thermal efficiency, and efforts should be made to minimize this negative impact.

Impact of thermal swing piston top land coatings on gasoline engine performance and raw emissions

Upcoming legislations aim to significantly reduce carbon dioxide and hydrocarbon emissions compared to current regulations. Accordingly, options have to be evaluated to not only convert the raw emissions in a catalytic converter, but also to reduce the raw emissions from the combustion process in the first place. Therefore, thermal piston top land coatings, which lead to an oscillating piston surface temperature were investigated on a single cylinder research engine using a gasoline RON95E10 fuel. Measurements were conducted at a compression ratio of 12.2 and a long Miller intake event. In this manuscript the results achieved with yttria stabilized zirconia in comparison to an uncoated piston are displayed. Significant effects of the coatings on the indicated efficiency could be observed mainly at low engine speeds and loads due to the high share of fuel energy in the wall heat losses and incomplete combustion. At these operating points, the reduction of wall heat losses can almost be fully transferred into indicated efficiency, leading to an increase in indicated efficiency of 6.3% by the yttria stabilized zirconia coating. At higher engine speeds and loads, the advantage in indicated efficiency vanishes and a decrease of 0.5% can be observed. Near full load operation the indicated efficiency slightly lower. However, the effects of a thermal swing coating on combustion efficiency and wall heat losses strongly depend on the operation conditions.

Analysis of the Vibrational Behavior of dual-fuel RCCI combustion in a Heavy-Duty Compression Ignited Engine fueled with Diesel-NG at Low Load

In the field of internal combustion engines, the Low Temperature Combustions (LTC) appear to have the potential to reduce the formation of both soot and nitrogen oxides. One of the most promising LTC is Reactivity Controlled Compression Ignition (RCCI) which is based on the combustion of a lean low reactivity fuel-air mixture generated in the intake manifold and autoignited by small injections of high reactivity fuel introduced at high pressure in the combustion chamber. By the combination of net-zero natural gas and biodiesel, such LTC methodology might represent a suitable solution moving toward zero-emissions in transportation sector.Despite the potential to reduce pollutant emissions, Low Temperature Combustion strategies face a challenge in controlling the angular position where the combustion takes place which can be overcome by a proper management of the high-pressure injections.One potentially interesting application is related to trucks, mainly because they have long periods of idling, since emissions can be drastically reduced by means LTC. A single cylinder research engine for heavy duty application is operated under steady state conditions at low load and speed to analyze the possibility of controlling the engine behavior in dual fuel RCCI mode. The results indicate that the combustion mode switches from the dual-stage to gaussian within a narrow angular range. A further advance of the start of injection can generate misfires and significant variations in typical combustion indexes, while a delayed start of injection can cause impulsive combustion that rises the cylinder temperature and results in high-frequency pressure oscillations inside the combustion chamber. These oscillations are related to the combustion chamber typical resonance frequency, and if relevant in amplitude and persist for a long time, they might generate a potential source of failures.

Experimental and chemical-kinetic evaluation of a heavy-duty methanol PFI engine with direct water injection

Internal combustion engines are still widely used for propulsion in modern vehicles. Upcoming emission legislation imposes stricter limits on exhaust emissions. One method to achieve emission compliance is by using a three-way catalyst (TWC), which offers excellent emission reduction if the mixture is stoichiometric. However, stoichiometric mixtures in spark-ignited engines have the drawback of increased knock propensity. Knock can be mitigated by using water injection, which serves as both a diluent and utilizes latent heat to reduce the temperature, thereby reducing the reactivity of the unburned mixture. Methanol as a fuel has received more attention thanks to its high research octane number (RON) and its potential to contribute to decarbonization when produced as e- or bio-methanol. In the current study, Direct Water Injection (DWI) was evaluated on a Heavy-Duty (HD) single-cylinder research engine fueled by methanol. This work aims to fill a research gap on methanol-fueled engines with water injection. A direct injection system of water was chosen as it offers the freedom to inject during the closed cycle. Furthermore, a chemical kinetic study on the oxidation of stoichiometric methanol–water mixtures was conducted based on findings in the literature suggesting that, under certain conditions, water mixed with alcohol (in this case, ethanol) can reduce the ignition delay. The experimental results demonstrate that DWI effectively suppresses knock and reduced Nitrogen Oxides (NOx), albeit with deteriorated combustion efficiency. The chemical kinetic study suggested that at lower to intermediate temperatures, water acts as an efficient third-body collider, which lowers the ignition delay. However, this effect is not significant for the typical timescales encountered in HD engines.

Effect of flexible camshaft technology on dual-fuel engine performance using phenomenological combustion model

AbstractThe objective of the current study is to investigate the effect of tunable valve timings on the performance and emissions of a dual-fuel marine engine. A simulation model was developed in MATLAB to simulate the valvetrain mechanism. The model generates different valve lift curves depending on the input conditions, and after that, it tests them against any possible collision with the piston. The valid valve lift curves were exported to a two-zone combustion model in AVL CRUISE-M platform. The combustion model depends on the fractal principle and aims to predict the in-cylinder parameters. In addition, it contains sub-models to calculate the ignition delay and emissions formation. Model results were compared against experimental data, as the latter were obtained from a heavy-duty, medium-speed, single-cylinder research engine, which employs natural gas as a main fuel. The results showed good agreement and the model was used for further investigations with other cam pairs. It has been found that the fractal combustion model can effectively represent the combustion behavior in the dual-fuel engine. Furthermore, valve timing has a significant influence on the engine performance and exhaust emissions. Results also revealed that applying Miller cycle can reduce the nitrogen oxides emissions, while the higher valve overlap period had a negative effect on methane slip.

Supercritical water injection in a single cylinder research engine: a PIV study

This work presents the experimental results of a fluid dynamic investigation to characterize the injection of supercritical water in the combustion chamber of an internal combustion engine. Particle Image Velocimetry (PIV) analysis is carried out in an optically accessible 2-stroke Diesel engine. A prechamber, equipped with two optical accesses is connected to the main cylinder through a tangential duct so that the piston stroke induces a swirled motion field with angular velocities typical of light duty engines for automotive application. The engine is equipped with an injection system for the production and injection of supercritical water, with the possibility to independently regulate the injection pressure, temperature, duration, and timing. Tests have then been carried out under different operating conditions to evaluate the impact of the fluid dynamics in the combustion chamber on the water spray. First, the airflow velocity field has been characterized at different engine crank train angles. The water spray has been macroscopically characterized for an injection temperature of 300°C and pressure of 30Mpa. Then, the supercritical water/air interaction has been explored, at different injection pressure, temperature, and Start of Injection (SOI) to provide global information in terms of spray morphology, tip penetration, and velocity vector distribution of the water droplets within the combustion chamber for different injection strategies.

A two-material thermal barrier coating spatially tailored for high-efficiency GCI combustion

Continued research into thermal barrier coatings (TBCs) for internal combustion engines has generated insights into the design of TBCs that can increase fuel conversion efficiency. In this work, two low thermal inertia TBCs (a commercially available Gen 1 material, Gadolinium Zirconate, and a proprietary Gen 2 material) were experimentally tested in gasoline compression ignition (GCI) on a light-duty single cylinder research engine. Compared to a metal baseline, a 250-micron thick Gen 1 coated piston produced an efficiency benefit of 0.4 percentage points (pp) at 6 and 10 bar net indicated mean effective pressure (IMEPn) and a 0.2 pp penalty at 15 bar IMEPn. The Gen 1 coating also showed an uHC and smoke penalty. An 80-micron thick Gen 2 coated piston showed an efficiency benefit of 0.9 pp at 6 bar IMEPn and 0.4 pp at 10 bar IMEPn, but an efficiency penalty of 0.5 pp at 15 bar IMEPn. The Gen 2 coating, which has a lower thermal inertia than the Gen 1 coating, displayed durability problems while the Gen 1 coating did not. A third piston was coated with a 120-micron thick Gen 2 coating everywhere except the high failure outer bowl region, which was coated with a 120-micron Gen 1 coating. This hybrid coating displayed good durability, an uHC emission penalty, a smoke benefit, an efficiency benefit of 0.1 pp at 6 bar IMEPn, an efficiency benefit of 0.4 pp at 10 bar IMEPn, and no change in efficiency at 15 bar IMEPn. These results indicate that a durable Gen 1/Gen 2 coating can provide an efficiency benefit to GCI combustion, and that further improvements on piston-spray interaction optimization and surface sealing of the TBC, as well as increasing the coated combustion chamber surface area (e.g. head and valves) can add further improve efficiency.

Extended Coherent Flame Model applied to an optical single-cylinder engine fueled with ethanol

One way to achieve a fast track for the decarbonization of the transportation sector is through the usage of biofuels. Among the many biofuels available for transportation, ethanol is one of the most promising, especially when combined with direct-injection spark-ignited engine technologies. The present work aims to validate 3D Computation Fluid Dynamics (CFD) ethanol spray and combustion models with the calibration of specific model parameters using experimental data obtained with optical measurements. Focus is given on the investigation and determination of the Extended Coherent Flame Model parameters for hydrous ethanol turbulent spray combustion. To characterize the spray produced by the injector, measurements obtained with a Phase Doppler Interferometer system are used. Natural luminosity and in-cylinder pressure are acquired on a single-cylinder research engine with optical access. The work also considers results obtained from 1D and 3D CFD models to supplement the acquired experimental setup. From the comparison between experimental and numerical results, it comes out that a correction of the Extended Coherent Flame Model turbulence stretch parameter can be done according to a ratio of flow and combustion length scales obtained at the spark time. In this sense, an expression is proposed to allow the correction of such a parameter in different engine operating conditions. Accordingly, in-cylinder mean effective pressure calculated with 3D CFD simulations show a good agreement with the experimental data for all studied cases.

Reverse engineering as a modern methods of test bed modernization

The main purpose of the work is to present the individual stages of the reverse engineering process on the example of a dynamometer equipped with a single-cylinder research engine AVL 5804. The scope of work includes theoretical and practical aspects of measurements using 3D scanners. The Scantech KSCAN Magic hand-held optical scanner was used to measure the geometry of the dynamometer. The CAD model was created in the Autodesk Inventor program, and the correctness of its execution was checked by basing it on the scan and generating a scale of deviations along with a color representation of their size in the GOM Inspect program. The work was summarized with an example of upgrading the current stand based on a previously made design, which significantly shortened the process of modifying the intake system. <hr> <iframe width="560" height="315" src="https://www.youtube.com/embed/UT3n2IZL5ck?si=O5f0OFr3ThQaWC8Q" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" allowfullscreen></iframe>

An analytical approach to converting vibration signal to combustion characteristics of homogeneous charge compression ignition engines

Homogeneous charge compression ignition (HCCI) is a promising low-temperature combustion technique for low-emission internal combustion engines. Unlike conventional engines, HCCI lacks a direct ignition control mechanism, necessitating closed-loop combustion control. This study proposes a phenomenological-based, cost-effective, and non-intrusive approach using vibration data analysis to determine essential combustion parameters. Experiments were conducted on a single-cylinder research engine with an accelerometer attached to the engine head. The engine operation envelope covered the whole engine’s operating area in naturally aspirated HCCI mode. Wavelet analysis revealed that combustion-related frequencies centered around 500 Hz, independent of operating conditions. The correlation-seeking analysis included peak acceleration amplitude and its crank angle with peak heat release rate (HRR) data. The peak HRR location was accurately identified within one degree when vibration amplitude exceeded the 100 m/s2 threshold. This encompassed 98.5% of the analyzed combustion cycles. The peak HRR prediction accuracy had a maximum error below 21% and was suitable to monitor reaction rates, especially in incomplete combustion and high ringing cycles.

Experimental Study on Spark Assisted and Hot Surface Assisted Compression Ignition (SACI, HSACI) in a Naturally Aspirated Single-Cylinder Gas Engine

Abstract Spark assisted compression ignition (SACI) represents an efficacious technique to extend the operating range and control combustion timing in homogeneous charge compression ignition (HCCI) engines. Recently, a hot surface ignition system (HSI) was demonstrated to enable hot surface assisted compression ignition (HSACI) featuring similar combustion characteristics compared to SACI. This work compares both combustion processes with regard to control and combustion characteristics, the strength of the ignition systems, and cycle-by-cycle variations (CCV). Engine trials were conducted using a single-cylinder research engine fueled with natural gas. The engine operated naturally aspirated at an engine speed of 1400 1/min and steady-state conditions. Experimental conditions cover relative air-fuel ratios λ = 2.1–3.1, intake temperatures Tin = 140–170 °C and intake pressures pin = 993–995 mbar. Results show similar capabilities of SACI and HSACI to control combustion timing by means of spark timing in SACI and hot surface temperature in HSACI. Heat release analyses of individual combustion cycles point out the similarity of both combustion processes. The evaluation of the strength of the ignition systems reveals that HSACI extends the lean limit by Δλ = 0.05–0.10 and advances the earliest applicable combustion timing (MinCA50) by ΔMinCA50 = 1.0–4.5 °CA provided that ringing is not of concern. Comparison of CCV in HCCI, SACI, and HSACI shows highest combustion stability for HCCI, followed by SACI. HSACI evinces highest CCV due to a larger variation at the start of combustion.

Further Development of Gasoline from the bioliq® Process with Focus on Particulate and Hydrocarbon Emissions

The production of CO2-neutral fuels is a key technology to achieve the European Union’s targets of greenhouse gas reduction in the transport sector. For a straightforward application such as drop-in fuel, regenerative gasoline must meet emission requirements without causing significant changes in engine parameters. The objective of this work was to demonstrate the emission reduction potential of fuel from the bioliq® plant by reducing the content of heavy aromatics in the product refinement. For three blends with varying contents of bioliq® fuel, the spray behavior was studied in a pressurized chamber and the particulate and hydrocarbon emissions were investigated using a single-cylinder research engine. With increasing bioliq® fuel content, atomization was degraded by lower flash boiling at low pressure. This effect vanished at higher chamber pressures. Measurements of particulate and hydrocarbon emissions showed significant improvements of 50% to 100% and 10%, respectively, compared to previously investigated bioliq® fuel fractions from 2017. The formation of particulate emissions is virtually unaffected by the blending of bioliq® fuel, due to the absence of heavy aromatics in the refined bioliq® product. Hydrocarbon emissions increased by 20% with higher bioliq® fuel content and late injection timings due to inferior mixture formation as a result of slightly reduced atomization. However, near the optimum injection timing, the hydrocarbon emissions are independent of the bioliq® fuel admixture.