Single Cylinder Diesel Engine Research Articles

Analysis of the Influence of Fuel Dose on the Electrical Parameters of the Starting Process of a Single-Cylinder Diesel Engine

Analysis of the Influence of Fuel Dose on the Electrical Parameters of the Starting Process of a Single-Cylinder Diesel Engine

Effect on polytropic index, performance and emission of diesel engine using hydrogen as gaseous fuel with additive di-tert butyl peroxide

Diesel engines are commonly used due to its higher reliability and better fuel conversion efficiency. However, it produces exhaust emissions like carbon dioxide (CO2) and particulate matter (PM). Hydrogen gas is regarded as a clean fuel as it is free from carbon. The addition of hydrogen fuel enhances the burning rates and extends the flammability limits of fossil fuels, and therefore has the potential of reduced exhaust emission in diesel engines operating on dual fuel mode. This paper has investigated the effect of hydrogen addition to the performance and emissions of a single-cylinder diesel engine, working in dual fuel mode with additive di-tert butyl peroxide (DTBP). About 25% hydrogen was introduced into the cylinder on a mass basis via the engine intake manifold with the addition of additive di-tert butyl peroxide up to 5% in diesel fuel. In this experimental study, mean gas temperature, indicated mean effective pressure (IMEP), brake mean effective pressure (BMEP), polytropic index, and exhaust emissions were studied at medium (53%) and high (69%) load conditions. The indicated mean effective and brake mean effective pressure was 9.79 bar with a 3% addition of additive and 4.15 bar with the 5% addition of additive as compared with 8.71 bar and 4.11 bar diesel fuel operation. 16% hydrogen addition with 1% di-tert butyl peroxide, IMEP, and BMEP are 10.92 bar, and 4.14 bar respectively.

Modeling the impact of plastic oil obtained from xlpe cable wastes on diesel engine performance and combustion parameters with the response surface method

The world's expanding population requires alternative energy sources to meet its energy needs. One such alternative is the efficient recovery of plastic waste through pyrolysis. The liquid produced from waste plastics via pyrolysis is a valuable commodity that may serve as fuel substituted for internal combustion engines. In this study, waste plastic oil (WPO) and diesel fuel (D100) blends (10%, 20%, 30%, 40% and 50% by volume) obtained by pyrolysis of waste XLPE cables were experimentally investigated and analyzed using response surface methodology (RSM) to determine their effects on the combustion parameters of a four-stroke, single cylinder diesel engine at different engine loads (750, 1500, 2250, 3000, 3750 and 4500 W). A response surface model was constructed using a two-factor central composite complete design and analysis of variance based on the experimental results obtained. The model determined the optimum values of WPO ratio and engine load that correspond to one of the finest brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), hydrocarbon (HC), carbon monoxide (CO), nitrogen oxides (NOx), and smoke emission levels. The study's optimization findings indicated that the optimal WPO ratio is 19.6%, and the optimal engine load is 2600 W. The BTE, BSFC, CO, HC, NOx, and smoke were found to be 22.3%, 332.3 g/kWh, 0.033%, 31.5 ppm, 397.9 ppm, and 1.63%, respectively, at the optimal WPO ratio and engine load. The R2 (correlation coefficient) values for BTE, BSFC, CO, HC, NOx, and smoke emissions were determined to be 99.95%, 97.76%, 98.10%, 99.74%, 99.74%, 99.79%, and 95.67%, respectively. The mean error rates, ranging from 0.64% to 4.27%, were deemed satisfactory when comparing the replies to the experimental data. The findings of this study demonstrated that the response surface method is a very efficient approach for forecasting and enhancing a diesel engine's performance and emission characteristics by using waste plastic oil.

Toward improving efficiency and mitigating emissions in a natural gas/diesel direct injection dual fuel engine using EGR

As emissions regulations become more and more stringent and conventional fuel sources rarefaction, new alternatives are emerging to address this situation. Dual fuel engines are among the promising solutions, offering both ecological and economic advantages. However, these engines often confront constraints linked to high levels of unburnt hydrocarbons (HC) at low loads and NOx emissions at high loads. To overcome these problems and guarantee high-efficiency overall operating loads, exhaust gas recirculation (EGR) is a potential solution. In the present experimental study, appropriate modifications have been carried out to a single-cylinder diesel engine to ensure dual fuel operation with EGR. Natural gas and diesel are used as the primary and pilot fuel, respectively. At low load operations, the EGR rate is increased up to 35% until the reduction of unburnt hydrocarbons. However, at high loads, the EGR rate is carefully adjusted, as the combustion efficiency easily deteriorates due to oxygen amount lack in the combustion chamber. Also, minimizing NOx emissions is prioritized in all load conditions while keeping thermal efficiency in sight. In addition, the variation in the amount of pilot fuel is studied for improving the combination of dual fuel engine operation with the EGR technique. This made it possible to determine the influence of load, EGR rate, and pilot fuel quantity on the engine in response to the triple challenges of reducing NOx and HC and improving thermal efficiency. The results show that an adequate EGR rate of 30%, depending on the operating conditions, can reduce HC emissions by >25% while increasing thermal efficiency by around 20%. This result is accompanied by a significant reduction, over 90%, in NOx emissions.

Assessing the impact of sargassum algae biodiesel blends on energy conversion in a modified single-cylinder diesel engine with a silica-incorporated diamond-like coated piston

ABSTRACT As coal and oil reserves deplete, the world is shifting to alternative fuels and renewable energy. Researchers are exploring a cleaner alternative to fossil fuels for powering automobiles. In this investigation, biodiesel was synthesized from brown marine algae (Sargassum algae) using transesterification process. Silica-incorporated diamond-like coating (DLC) was done on the engine piston by using the chemical vapor deposition (CVD) process with flow rate of 7sccm of C2H2. Three different coating thicknesses, such as 50,100, and 150 µm, were employed on the CI engine piston. Mechanical properties such as hardness, wear, and microstructure analysis were investigated. Analysis of mechanical characteristics reveals that pistons with a 100 μm coating have enhanced characteristics compared to those with other pistons. Using a 100 μm silicon coated piston on a single-cylinder Kirloskar engine, four blends (B10, B20, B30, and B40) were compared to neat diesel. At maximum engine load conditions, the B40 blends produced 42 ppm of HC whereas neat diesel with 19 ppm which is 57% higher than diesel and CO emission concentration increased by 4.9% than diesel. Similarly, brake-specific fuel consumption was observed at maximum load conditions for diesel with 0.18 kg/kWh and 0.20 kg/kWh for B10D90 which is 9.54% higher than diesel. As a result, it is critical to recognize the importance of sargassum’s potential for producing sustainable energy toward green globalization.

Investigation into the Impact of Piston Bowl Size on Diesel Engine Characteristics with Changes in Fuel Injection Pressure and Boost Pressure

This study presents the effects of piston bowl size on the characteristics of a four-stroke single-cylinder diesel engine, which is considered in relation to changes in factors such as fuel injection pressure and turbocharger pressure. The study was carried out by 3D modeling using AVL Fire with an omega combustion chamber size and dimensions determined by the ratio between the diameter and depth of the piston bowl, which varies from 3.4 to 10.0. Additionally, the turbocharger pressure varies from 0.15 to 0.45 MPa at an engine speed of 1400 rpm and fuel injection pressure up to 300 MPa. The results show that the engine reaches the best values of indicated power, fuel efficiency, and a substantial decrease in emissions of nitrogen oxides at a turbocharger pressure from 0.25 to 0.35 MPa and with a ratio of the diameter to the depth from 7.8 to 10. However, the injection angle changes slightly, and the penetration depth and the tip velocity decrease with increasing boost pressure. While the piston bowl parameters only impact significantly on the tip velocity, the penetration and the spray angle are almost unchanged. In addition, the variation in the diameter of the combustion chamber has an influence on the fluctuation of the spray tip velocity and penetration.

Impacts of pine oil and hydrogen induction with hemp oil methyl ester on dual fuel reactivity controlled compression ignition combustion in diesel engine

AbstractThe current research focuses on the impacts of pine oil injection and hydrogen induction separately with hemp oil methyl ester (HOME) in the single cylinder diesel engine in dual fuel‐reactivity controlled compression ignition (DF‐RCCI) combustion mode. The engine was tested under a DF‐RCCI mode for the different energy shares of 10% pine oil with HOME (10P‐HOME), 30% pine oil with HOME (30P‐HOME), 3‐lpm hydrogen with HOME (3‐lpmH2‐HOME), and 6‐lpm hydrogen with HOME (6‐lpmH2‐HOME) separately at 345 °CA bTDC of low reactivity fuel (pine oil and hydrogen) and 23°C bTDC injection timing of high reactivity fuel (HOME). The results showed a higher Brake Thermal Efficiency (BTE) of 7.44%, 5.32%, 5.72%, and 2.46% for 6‐lpmH2‐HOME, 3‐lpmH2‐HOME, 30P‐HOME, and 10P‐HOME fuel shares, respectively, over the conventional diesel combustion (CDC) at full load. 30P‐HOME, 3‐lpmH2‐HOME, and 6‐lpmH2‐HOME fuel combinations recorded 4.08% 4.42%, and 5.69% lower brake specific fuel consumption (BSFC), respectively, at full load. When comparing DF‐RCCI combustion to CDC, an increase in the heat release rate (HRR) of 2.89%–26.50% and a rise in peak cylinder pressure of 0.77%–12.99% were observed. The 30P‐HOME, 3‐lpmH2‐HOME, and 6‐lpmH2‐HOME emit less smoke in DF‐RCCI combustion mode by 13.06%, 4.84%, and 7.26%, respectively at full load condition. When using 30P‐HOME the exhaust gas temperature (EGT) decreased by 3.50% at full load condition. At part and full load conditions, the 30P‐HOME fuel share reduced oxides of nitrogen (NOX) emissions by 3.93% and 5.26%, respectively.

Mathematical modelling for predicting performance and emissions of a diesel engine fuelled with palm kernel biodiesel–diesel-diethyl carbonate fuel blends

The search for environmentally friendly and sustainable alternatives to conventional diesel fuels has prompted investigations into blends of biodiesel and oxygenated additives like diethyl carbonate. This study focuses on developing mathematical models to predict the performance and emissions of a single-cylinder diesel engine running on palm kernel biodiesel blended with varying proportions of diethyl carbonate. Response Surface Methodology with a general factorial design was employed to create mathematical models for brake thermal efficiency, brake-specific fuel consumption, hydrocarbon, carbon monoxide, and oxides of nitrogen emissions. The two input variables were engine load (five levels) and diethyl carbonate percentage in the fuel blend (five levels). Second-order models were developed, and model fit was evaluated using analysis of variance (ANOVA) at 95% confidence. The developed RSM models showed excellent fit with high R-squared values close to unity, satisfying the model adequacy criteria. ANOVA revealed the models to be statistically significant predictors of the response variables based on load and diethyl carbonate percentage. The optimum operating condition for best performance and emissions balance was found to be 71% load and 10% diethyl carbonate inclusion. The study emphasises the importance of alternative fuels in mitigating environmental pollution and reducing dependence on fossil fuels.

Ammonia-enriched biogas as an alternative fuel in diesel engines: Combustion, performance and emission analysis

This study investigates the potential of ammonia as a secondary fuel in diesel engines, amidst the rising interest in alternative fuels and the growth of electric vehicles. Unlike hydrogen, with its higher flammability and safety concerns, ammonia offers a viable, sustainable fuel source. A single-cylinder diesel engine was utilized to assess engine performance and combustion characteristics using ammonia gaseous blends. Ammonia was combined with biogas to mitigate its corrosive effects and compensate for its lower heating value. Th entire best conducted with constant ammonia flow rate of 30 LPM. Diesel was mixed with biogas in compositions of 10 LPM, 20 LPM and 30 LPM, and tested under engine loads of 25%, 50%, 75%, and 100%. The blend with the highest ammonia concentration (B30B3) exhibited the largest heat release rate, highlighting a strong correlation between ammonia content and heat release levels. This is attributed to the premixed combustion phase and the accelerated flame speed associated with ammonia. An increase in ammonia content resulted in higher brake thermal efficiency and reduced brake specific fuel consumption. All ammonia-inclusive blends showed a decrease in hydrocarbon and carbon monoxide emissions, with the lowest emissions observed in the B30B3 blend. However, the high flammability of biogas in the B30B3 blend, compared to diesel, and enhanced fuel atomization, led to increased nitrogen Oxides formation. The results clearly indicate that combination of ammonia along with the biogas enhances the combustion and reduces greenhouse gas emissions. Findings of this study provides valuable insights into the use of ammonia as a sustainable alternative in diesel engines, offering a improved balance between combustion efficiency and environmental impact.

Laboratory Tests of Electrical Parameters of the Start-Up Process of Single-Cylinder Diesel Engines

Despite continuous work on new power systems for vehicles, machines, and devices, the combustion engine is still the dominant system. The operation of the combustion engine is initiated during the starting process using starting devices. The most common starting system used is the electric starter. The starting process of an internal combustion engine depends on the following factors: the technical condition of the starting system, technical condition of the engine, battery charge level, lubricating properties, engine standstill time, engine and ambient temperature, type of fuel, etc. This article presents the results of laboratory tests of the electrical parameters of the starting process of a single-cylinder compression–ignition engine with variable fuel injection parameters and ambient temperature conditions. It was confirmed that for the increased fuel dose FD2, higher values of the measured electrical parameters (Imax, Pmax, and Pmed) were obtained compared to the series of tests with the nominal fuel dose. Knowledge of the values of the electrical parameters of the starting process is important not only for the user (vehicle driver, agricultural machinery operator, etc.), but above all for designers of modern starting systems for combustion engines and service personnel. The obtained results of testing the electrical parameters of the combustion engine during start-up may be helpful in designing new drive systems supported by a compression–ignition combustion engine.

Assessment of performance, combustion, and emission characteristics of single cylinder diesel engine fuelled by pyrolysis oil + CeO2 nanoparticles and 1-butanol blends

This experimental work focused on trials on diesel engines using Pyrolysis blends. The novelty in this work is the addition of cerium oxide additives with 1-butanol as an ignitor. The blends used were D100, 90D7WPO3B + 25 ppm CeO2, 85D10WPO5B + 50 ppm CeO2, 80D13WPO7 + 75 ppm CeO2 and 100WPO + 100 ppm CeO2. The results were outstanding as BTE is good for the fuel 90D7WPO3B + 25 ppm CeO2 by 36.2%, which is 12.25% greater than diesel, BSFC is better for the blend 90D7WPO3B + 25 ppm CeO2 by 0.22 kg/kWh, and maximum in-cylinder pressure obtained for 90D7WPO3B + 25 ppm CeO2 blend rated as 66.45bar; and maximum HRR is obtained for 85D10WPO5B + 50 ppm CeO2 blends by 84 J/ deg CA, BSEC of 85D10WPO5B + 50 ppm CeO2 blend is lower next only to diesel by 12.5 KJ/kWh, NOX emission minimum for 100WPO + 100 ppm CeO2 blends rate of 12 g/kWh, 14.2% lower than diesel, and lowest CO is attained for blend 80D13WPO7 + 75 ppm CeO2 blends at a rate of 0.8 g/kWh, 27.7% less than diesel, CO2 is minimum for blend 80D13WPO7 + 75 ppm CeO2 rate of 5 g/kWh; 18.03% less than diesel and HC is minimum for blend 100WPO + 100 ppm CeO2 blend rate of 0.18 kg/kWh; Which is 40% lower than diesel.

Investigation of the performance and emissions of a diesel engine fuelled with bio-oil generated through microwave-assisted pyrolysis of a blend of hazelnut, walnut, and polyethylene terephthalate waste

New and renewable energy sources are the most important issue nowadays. Bio-oil which can replace fossil fuel is an alternative source of energy. In this study, the performance effects and emissions of bio-oil produced by microwave-assisted pyrolysis system (MAP) from the walnut shell (WS), hazelnut shell (HS), and polyethylene terephthalate (PET) waste mixtures on a single-cylinder diesel engine were investigated. For this purpose, WS, HS, and PET wastes were mixed in two different proportions and converted into pyrolytic oil in the MAP system at 700 watts of microwave power and a 30-minute retention time. Produced pyrolytic oils were converted into bio-oil as S1 (46.25% WS + 46.25% HS + 2.5% PET) and S2 (43.75% WS + 43.75% HS + 7.5% PET) through a 3-stage basic upgrading steps. Experimental results showed that MAP of mixed WS, HS, and PET resulted in high hydrocarbon content bio-oil. In the engine experiments, bio-oil was mixed with diesel at 10%, 20%, and 30% ratios by volume and used in a diesel engine at different Brake Mean Effective Pressure (BMEP) (1.4, 2, 2.7, and 3.4 bar). Engine performance has been found to be comparable to diesel at low blend percentages. At 3.4 bar BMEP, while the brake-specific fuel consumption (BSFC) of diesel was 712 g/kWh, it was obtained as 832 and 804 g/kWh at S1 and S2, respectively. However, when the emissions were evaluated in general, it was determined that the emission values increased with increasing bio-oil/diesel blend ratios due to the high viscosity, higher density, and low cetane number of bio-oil compared to diesel.

Water-in-Biodiesel Emulsion with Hydroxy (HHO) Gas Fuel Enrichment for Single-Cylinder Diesel Engine Application

The rising issue of the depletion of fossil fuels opened a new pathway to seek alternative fuels to fulfil World Sustainable Development Goals (SDG). The application of high-blending biodiesel is possible however, it causes the diesel engine to perform poorly due to high viscosity, high fuel consumption, and increased NOx emission. To comply with the strict regulation, the idea of combining alternative fuels of high blending biodiesel, water-in-biodiesel emulsion, and hydrogen is seen as possible to solve the issue of each alternative fuel. Therefore, this study focused on the effect of high blending of biodiesel, water-in-biodiesel emulsion with hydroxy (HHO) enrichment in single-cylinder diesel engines on engine performance and exhaust emission. The fuel tested for this study are B10, B50, and an emulsion of B50 with the addition of HHO known as B50H and tested on engine speeds of 2400rpm under various loading conditions of 1kW, 2kW, 3kW, and 4kW. The result showed the B50H showed improvement in Fuel Consumption (FC) by 4%, 5% for Brake Thermal Efficiency (BTE), and reduced Nitrogen oxide (NOx) by 23% compared to B10 fuel. Thus, the combination of high blending of biodiesel, water-in-biodiesel emulsion, and HHO gas successfully improved diesel engine performance and reduced harmful exhaust emissions to promote clean and renewable energy, without depending on current diesel fuel.

Investigations on a Spark Ignition Engine, Part II: Impact of Hydrogen Addition and Compression Ratio on a Biogas-Fuelled Engine

Performance, emissions and combustion were studied using a spark ignition engine modified from a single-cylinder diesel engine with varying compression ratios and hydrogen addition. When the compression ratio increases, there is a slight increase in brake power and thermal efficiency. There is a small increase in brake power and brake thermal efficiency when the compression ratio is above 13:1. Increased emissions of nitric oxide, hydrocarbon, and carbon monoxide were observed at compression ratios above 13:1. Leaner mixtures, brake power and brake thermal efficiency are lowered. Spark timing is retarded as the compression ratio rises which results in high peak pressure and rate of heat release. At a compression ratio of 13:1, a small amount of hydrogen (15% on an energy basis) was added along with biogas. The lean limit of biogas combustion and the combustion rate are greatly increased by the addition of hydrogen. In addition, there was a rise in brake power and thermal efficiency. The levels of hydrocarbons were significantly reduced. Nitric oxide emissions did not rise as a result of the use of the retarded ignition timing. The effect of two throttle conditions on spark ignition engines using biogas as fuel is presented as Part I of this study.

Utilization of RSM to optimize the performance and emissions of a single cylinder diesel engine using waste hazelnut biodiesel

One of the environmentally friendly, biodegradable, and renewable alternative fuels widely used around the world is biodiesel. Among vegetable oils, hazelnut oil has great importance in biodiesel production due to its high content of oleic acid. For this study, it is aimed to determine the optimum mixing ratio of biodiesel, produced from waste hazelnut oil (WHB). The tests were carried out on a diesel engine operated with WHB/diesel mixtures at different loads. By means of the design of experimental method (DOE), three different fuel ratios (WHB0, WHB15 and WHB30) were defined and tests have been performed. The results obtained from the tests were analyzed using the response surface method (RSM). Engine load and mixing ratio were determined as input factors while CO, NOx, smoke, indicated thermal efficiency (ITE), ignition delay (ID) and break specific fuel consumption (BSFC) were determined as output factors. In the mathematical model created, the R2 values were found to be 0.98, 0.95, 0.91, 0.98, 0.99 and 0.90 respectively. The high R2 values indicated a strong correlation between the optimization outputs and the real experiments. By using these performance and emission parameters, optimization was performed to identify the optimum blend ratio and load. Based on the results, the optimum inputs were determined as 8.46 Nm load and 4.86 % blend ratio. As a result, with the optimized fuel blend, BSFC (8.03 %), ID (3.57 %), and NO (2.87 %) increased while ITE (7.7 %), CO (18.37 %), and smoke (26.15 %) decreased comparing to WHB0. Despite the slight increase in consumption, the results showed that this blend could be used in an environmentally efficient manner, thanks to the reduction in pollutant emissions.

Emission and performance investigation of mango seed oil biodiesel supplied with n-pentanol and n-hexanol additives and optimization of fuel blends using modified deep neural network

Abstract In this study, the emission and performance characteristics of single-cylinder diesel engines were tested using various biodiesel blends prepared by mixing diesel with mango seed oil biodiesel (MSOB). Furthermore, the effect of n-amyl and n-hexanol alcohol additions on the performance and emission results of manufactured biodiesel blends is investigated and compared with diesel fuel. On the other hand, a hybrid deep neural network (DNN) based on the manta ray foraging optimization (MRFO) method is developed to forecast ideal biodiesel blends in order to reduce emissions from diesel engines while improving performance. The optimal brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) for this study were 32.3916 % for 75 % diesel + 20 % MSOB + 5 % n-hexanol fuel and 0.0453 kg/kWh for 75 % diesel + 20 % MSOB + 5 % n-amyl fuel, respectively. The optimal emissions from the test engine were 0.1034 % CO from 60 % diesel + 20 % MSOB + 20 % n-hexanol and 28.886 ppm HC from 75 % diesel + 20 % MSOB + 5 % n-hexanol fuel. The optimal smoke and NO x levels are achieved with a blend of 60 % diesel, 20 % MSOB, 5 % n-amyl, and 5 % n-hexane. Moreover, the developed DNN-MRFO achieved 0.9979, 0.9992 and 0.9975 overall regression coefficients during training, validation and testing. The root mean square error (RMSE) of DNN-MRFO also ranges from 0.019 to 0.032.

Combustion performance and emission characteristics of aloevera diesel-emulsified fuel in a DI diesel engine.

Nowadays, mankind is very particular about the usage of energy in the most effective manner by keeping the view of less adulterating the atmosphere, which are the key aspects of many scientists all around the world. In this particular study, the aloevera diesel has been chosen as the primary fuel, and studies have been conducted on emission pollutant characteristics by choosing an appropriate diesel engine. Furthermore, stable emulsions have been produced by using aloevera, and the same was mixed with diesel at the ratio of 5% and 10% as the compound. Moreover, span 80 and tween 80 are used as the surfactant with an HLB balance of 9.95. Similarly, the emulsions are prepared with the help of a mechanical stirrer for exact duration of 30min. In order to carry out the experimental investigation process, a single-cylinder diesel engine was used with a data acquisition system. The entire analyses are carried out with two sets of methods such as no load and full load. The performance and combustion characteristics such as heat release, combustion pressure, thermal efficiency (B5 - 6.303%↑, B10 - 3.789%↑), and specific fuel consumption of the brake (B5 - 4.2%↑, B10 - 5%↑) were measured. Likewise, emission parameters such as CO (B5 - 0.02%↓, B10 - 0.04%↓), HC (B5 - 1 PPM↓, B10 - 5 PPM↓), NOx (B5 - 20 PPM↓, B10 - 89 PPM↓), and CO2 (B5 - 0.3%↑, B10 - 0.4%↑) are measured by using AVL Di-gas analyzer. It was noticed that increased peak cylinder pressure and greater heat release rate were on account of a longer ignition delay period. Additionally, an increase in engine performance and the corresponding reduction in exhaust emission have also been observed upon using aloevera-emulsified diesel fuel.

Effects of biodiesel injector configuration and its injection timing on performance, combustion and emissions characteristics of liquid ammonia dual direct injection engine

Ammonia is a promising carbon-neutral fuel that can be stored and transported in liquid form, offering a viable alternative to diesel fuel. In addition, it can be used directly in diesel engine in its liquid form in dual fuel mode. Hence, a single-cylinder diesel engine was modified to implement two common rail (CR) injection systems, allowing the direct injection of liquid ammonia with biodiesel. As biodiesel was used for a pilot fuel with lower injected mass, this study aims to investigate the influence of the number of nozzles in the biodiesel injector on the performance, combustion, and emissions characteristics of the liquid ammonia-biodiesel dual direct injection engine. Therefore, the number of holes in the CR injector was closed in various configurations to improve injection parameters. Furthermore, various biodiesel start of injection (SOI) timings were tested, ranging from −24 to −14 CAD, while the SOI of ammonia was kept at −10 CAD with an ammonia mass ratio of 67.2%. The results showed that welding three nozzles from the original six-nozzle injector resulted in a remarkable 29.2% reduction in NH3 and CO emissions. Furthermore, the highest indicated thermal efficiency of 39.7% was obtained for the injector with 3b nozzles. Additionally, late injection of both fuels led to an increase in particulate matter emissions, from 10.5 to 15.2 mg/m3, due to the formation of fuel-rich zones at high temperatures. However, it reduced NOx and CO emissions by 1.4 and 4.4 g/kWh, respectively, compared to the early SOI of biodiesel. Moreover, the lowest N2O emission was measured at 115.0 ppm in the earliest SOI of biodiesel at −24 CAD.

Numerical optimization and experimental investigation of renewable diethyl ether-fueled off-road CI engines for sustainable transportation

Cleaner energy generation on light-duty off-road diesel engines is one of the objectives of this study, which utilizes renewable diethyl ether (DEE) as a replacement for diesel to minimize the reliance on fossil diesel fuel. In an air-cooled single-cylinder diesel engine, various DEE mixes of 5, 10, 15, 20 and 25% were attempted and evaluated under varying loads (0, 25, 50, 75 and 100%) in an effort to enhance the performance and emission characteristics of agriculture diesel engines and lower the environmental effect of harmful emissions. The injection pressure was optimized using computational fluid dynamics (CFD), and performance and emission outcomes were optimized through response surface methodology (RSM) techniques. The experimental results found that brake thermal efficiency and specific fuel consumption were enhanced for a higher proportion of DEE blends under increasing loads. In addition, increasing the engine load decreased CO emissions while increasing carbon dioxide (CO2), hydrocarbon (HC), and nitrogen oxide (NOx) emissions. Reduced CO, NOx, and HC emissions and increased CO2 were realized in the blended fuel samples compared to those of pure diesel fuel at increasing DEE percentages. In summary, the utilization of a 15% DEE blend and the optimization of the injection pressure to 210 bar resulted in a notable improvement of 10% in thermal efficiency and a decrease in emissions by 5% when compared to other parameters.

Effect of ceria–silica-based synthesized catalyst in a CI engine exhaust system operating with plastic oil blend

This study investigates the impact of ceria–silica (Ce–Si)-based catalyst integrated in the catalytic converter (CC) on the compression ignition (CI) engine's exhaust manifold. The synthesis catalyst, Ce–Si was developed with the solvothermal method and aged for 4 h at 55°C. Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscope, thermogravimetric analysis, energy dispersive X-ray spectroscopy and transmission electron microscopy analyses were carried out to conclude the synthesis of the catalyst. The catalyst performance of the CC was tested for the emission behavior of nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbon (HC) and smoke. A custom-built CC was installed on the test engine's exhaust manifold. The synthesis catalyst was installed in the engine exhaust route of the stationary single-cylinder diesel engine to conduct the study. To determine the effect of the synthesis catalyst on the exhaust manifold to test both diesel and DPB (B50) fuel with and without CC. Under maximum load conditions, the presence of CC reduced oxide of nitrogen and carbon monoxide emissions by 23% and 17%, respectively, compared to diesel. The synthesized aerogel catalyst has a low density and a high surface area relative to its volume. Ce–Si aerogel catalyst can be used to improve the conversion efficiency of nitric oxide (NO), unburned hydrocarbon and CO in the three-way CC.