Short-circuit Research Articles

Underground Cable Fault Detection

Underground cables play a crucial role in delivering electricity, ensuring a dependable power supply in both urban and industrial regions. However, detecting and resolving faults in these cables can be difficult due to their hidden placement. This project aims to develop an effective underground cable fault detection system that accurately identifies fault locations, reducing downtime. The system will combine electrical principles with modern sensing technologies to detect faults such as short circuits, open circuits, and insulation issues. By injecting a small current into the cable and analyzing the resulting voltage drop, the system will calculate the distance to the fault from the measurement point. Using a microcontroller along with sensors and signal processing units, it will determine and display the fault location in kilometers. Real-time fault detection will significantly decrease maintenance time and costs by quickly locating problem areas, enabling faster repairs and reducing power outages. This project aims to improve the efficiency and reliability of power transmission systems. Additionally, the system can be integrated with communication technologies for remote monitoring, allowing utility companies to detect and manage faults from centralized control centers.

Early Internal Short Circuit Diagnosis for Lithium-Ion Battery Packs Based on Dynamic Time Warping of Incremental Capacity

Timely identification of early internal short circuit faults, commonly referred to as micro short circuits (MSCs), is essential yet poses significant challenges for the safe and reliable operation of lithium-ion battery (LIB) energy storage systems. This paper introduces an innovative diagnostic method for early internal short circuits in LIB packs, utilizing dynamic time warping (DTW) applied to incremental capacity (IC). Initially, the terminal voltages of all cells within the LIB pack are ordered at any moment to determine the median terminal voltage, which is then used to generate the median IC curve. This curve acts as a reference benchmark that represents the condition of healthy cells in the pack. Subsequently, the DTW algorithm is utilized to measure the similarity between each cell’s IC curve and the median IC curve. Cells exhibiting similarity scores that exceed a specified threshold are identified as having MSC faults. Lastly, for the cells diagnosed with MSC conditions, a method for estimating short-circuit resistance (SR) based on variations in maximum charging voltage is devised to quantitatively evaluate the severity and evolution of the MSC. Experimental findings reveal that the proposed method effectively identifies MSC cells in the LIB pack and estimates their SRs without the necessity of a battery model, thereby affirming the method’s validity.

MoS2/porous carbon nanofiber heterostructures for efficient evaporation-driven generators.

Evaporation power generators (EPGs) based on natural water evaporation can directly convert heat energy from the surrounding environment into electrical energy. However, EPGs are difficult to commercialize due to the low charge generation and transport efficiency of single material systems, resulting in unsatisfactory open-circuit voltages and short-circuit currents. Here, we step by step prepared MoS2/porous carbon nanofiber (PCNF) heterogeneous systems by electrospinning and hydrothermal methods. Electron microscope measurements proven the uniform coating of high-crystalline quality MoS2 nanosheets on PCNF fabrics, and the uneven concave-convex surface increased the specific surface area. MoS2 covered PCNF fabrics retained good hydrophilicity, which was suitable for absorbing water and keeping the surface wet during long-term evaporation. Moreover, layered MoS2 with rich surface charge improved the charge transfer of the MoS2/PCNF fabrics. As a result, the open-circuit voltage and short-circuit current of the EPGs prepared with MoS2/PCNF fabrics were improved to 0.25 V and 75 μA, respectively, compared with those based on PCNF fabrics, which demonstrated that the MoS2 coatings improved the interaction area with water and the charge transfer effect of the EPGs. This heterogeneous combination strategy provides ideas for the preparation of high-performance EPG materials.&#xD.

Enhancing the Photovoltaic Efficiency of In0.2Ga0.8N/GaN Quantum Well Intermediate Band Solar Cells Using Combined Electric and Magnetic Fields

This study presents a theoretical investigation into the photovoltaic efficiency of InGaN/GaN quantum well-based intermediate band solar cells (IBSCs) under the simultaneous influence of electric and magnetic fields. The finite element method is employed to numerically solve the one-dimensional Schrödinger equation within the framework of the effective-mass approximation. Our findings reveal that electric and magnetic fields significantly influence the energy levels of electrons and holes, optical transition energies, open-circuit voltages, short-circuit currents, and overall photovoltaic conversion performances of IBSCs. Furthermore, this research indicates that applying a magnetic field positively influences conversion efficiency. Through the optimization of IBSC parameters, an efficiency of approximately 50% is achievable, surpassing the conventional Shockley–Queisser limit. This theoretical study demonstrates the potential for next-generation photovoltaic technology advancements.

Bidirectional enhancement of output performance of nanogenerators by M-COFs materials

The emergence of nanogenerators, which have the ability to capture mechanical energy from the environment and to collect and transmit tiny energy, is rapidly becoming a hot research topic. The performance of electrode materials is the key to the efficiency of nanogenerators. Covalent organic skeletons (COFs), a class of crystalline organic porous materials with the advantages of large specific surface area, high porosity, tunable structure, and flexible tailorability, have very significant advantages in being used as nanogenerator materials. In this paper, we synthesised two COF materials to investigate the effect of the introduction of active metals on the friction power generation performance of COFs without changing their topology, COF-2 containing zinc ions is capable of generating a short-circuit current of 107.5 µA during friction. The porous structure increases the effective contact area to form a larger charge density, and the introduction of metal ions can accelerate the charge separation and transport. The two bidirectional synergistic effects of the materials significantly improve the output performance of the nanogenerator, and a simple and efficient method is explored for the enhancement of the output performance of COF-based triboelectric nanogenerators.

High-Performance Triboelectric Nanogenerator with Double-Side Patterned Surfaces Prepared by CO2 Laser for Human Motion Energy Harvesting

The triboelectric nanogenerator (TENG) has demonstrated exceptional efficiency in harvesting diverse forms of mechanical energy and converting it into electrical energy. This technology is particularly valuable for powering low-energy electronic devices and self-powered sensors. Most traditional TENGs use single-sided patterned friction pairs, which restrict their effective contact area and overall performance. Here, we propose a novel TENG that incorporates microwave patterned aluminum (MC-Al) foil and microcone structured polydimethylsiloxane (MC-PDMS). This innovative design utilizes two PMMA molds featuring identical micro-hole arrays ablated by a CO2 laser, making it both cost-effective and easy to fabricate. A novel room imprinting technique has been employed to create the micromorphology of aluminum (Al) foil using the PMMA mold with shallower micro-hole arrays. Compared to TENGs with flat friction layers and single-side-patterned friction layers, the double-side-patterned MW-MC-TENG demonstrates superior output performance due to increased cone deformation and contact area. The open-circuit voltage of the MW-MC-TENG can reach 141 V, while the short-circuit current can attain 71.5 μA, corresponding to a current density of 2.86 µA/cm2. The power density reaches 1.4 mW/cm2 when the resistance is 15 MΩ, and it can charge a 0.1 μF capacitor to 2.01 V in 2.28 s. In addition, the MW-MC-TENG can function as an insole device to harvest walking energy, power 11 LED bulbs, monitor step speed, and power a timer device. Therefore, the MW-MC-TENG has significant application potential in micro-wearable devices.

Influence of Ti Layers on the Efficiency of Solar Cells and the Reduction of Heat Transfer in Building-Integrated Photovoltaics

This study examined the potential application of metallic coatings to mitigate the adverse effects of ultraviolet (UV) and infrared (IR) light on photovoltaic modules. Titanium coatings were applied on low-iron glass surfaces using magnetron sputtering at powers of 1000, 1250, 1500, 1750, 2000, and 2500 W. The module with uncoated glass served as a reference. The Ti layer thickness varied from 7 nm to 20 nm. Transmittance and reflectance spectra were used to calculate visible light transmittance Lt, UV light transmittance Ltuv, solar transmittance g, and visible light reflectance Lr. The obtained parameters indicated that the thinnest Ti layer (1000 W) coating did not significantly affect light transmittance, but thicker layers did, altering the Lt, g, and Lr factors. However, every sample noticeably changed Ltuv, probably due to the natural formation of a UV-reflective thin TiO2 layer. The differences in fill factor (FF) were minimal, but thicker coatings resulted in lower open-circuit voltages (Uoc) and short-circuit currents (Isc), leading to a reduction in power conversion efficiency (PCE). Notably, a Ti coating deposited at 2500 W reduced the power of the photovoltaic module by 78% compared to the uncoated sample but may protect modules against the unwanted effects of overheating.

A new integrated modelling and control of ternary pumped storage hydro power generation for small signal stability studies

Pumped storage hydro power generation (PSHPG), a reliable renewable energy source with an energy storage feature, can impart efficient damping torque to power system oscillations to improve small signal stability with appropriate modelling and additional compensation through the governor. But ternary PSHPG (T-PSHPG) has the unique feature of hydraulic short circuit (HSC) mode, where both pumping and generating modes operate simultaneously. This study presents a novel fourth-order modified Heffron Phillips (MHP) model of T-PSHPG in coordination with a multi-band Power system stabilizer (MB-PSS) employing 2-way penstock, where primary penstock circulates water from the upper reservoir to the lower reservoir through the turbine and secondary penstock divides primary penstock, thereby creating short-circuit path through the pump. Also, this model includes additional reactive power droop control to maintain the voltage profile. A new state space matrix has been developed for coordinating T-PSHPG in HSC mode with MB-PSS. The control parameters of the proposed coordinated model are set by a new multi-objective differential evolution-improved particle swam optimization (DE-IPSO) algorithm. With variable load, random solar and wind source penetrations, it has been found that the proposed model can provide adequate damping actions. The sensitivity of the proposed model has been observed by varying critical model parameters by ±50 %. For all conditions, the settling time of speed variation is within 2.672 s to 5.951 s and the minimum damping ratio lies within 0.105 to 0.455. The minimum damping ratio is 0.32 and the settling time is found to be 3.1 s for system response subject to sudden solar power variation, which has been observed by shifting system eigenvalues toward the left half of the complex plane. Time and frequency domain parameters with sensitivity analysis predict system oscillations being damped effectively with consistency for the proposed modelling and control strategy. The results are verified in real-time with OPAL-RT real-time digital simulator. It has been justified by the present study that appropriate modelling of T-PSHPG along with coordinated control action provided by MB-PSS can handle critical power system oscillations efficiently and effective damping torque can be imparted in HSC mode.

Triboelectric nanogenerator based on silane-coupled LTA/PDMS for physiological monitoring and biomechanical energy harvesting

Energy harvesting from ambient sources present in the environment is essential to replace traditional energy sources. These strategies can diversify the energy sources, reduce maintenance, lower costs, and provide near-perpetual operation of the devices. In this work, a triboelectric nanogenerator (TENG) based on silane-coupled Linde type A/polydimethylsiloxane (LTA/PDMS) is developed for harsh environmental conditions. The silane-coupled LTA/PDMS-based TENG can produce a high output power density of 42.6 µW/cm2 at a load resistance of 10 MΩ and operates at an open-circuit voltage of 120 V and a short-circuit current of 15 µA under a damping frequency of 14 Hz. Furthermore, the device shows ultra-robust and stable cyclic repeatability for more than 30 k cycles. The fabricated TENG is used for the physiological monitoring and charging of commercial capacitors to drive low-power electronic devices. Hence, these results suggest that the silane-coupled LTA/PDMS approach can be used to fabricate ultra-robust TENGs for harsh environmental conditions and also provides an effective path toward wearable self-powered microelectronic devices.

Influence of Plasmonic Au@Cl/N Co‐doped Carbon Dots on the Performance of Dye‐Sensitized Solar Cells

ABSTRACTThe synergistic influence of the LSPR (localized surface plasmon resonance) of gold nanoparticles (Au NPs) and the effect of nitrogen and chlorine co‐doped carbon dots (Cl/N‐CQDs) on dye‐sensitized solar cells (DSSCs) performance are investigated. The gold NPs are coated with a thin layer of Cl/N‐CQDs to produce the Au@Cl/N‐CQDs structure. DSSCs are fabricated by using Au@Cl/N‐CQDs as co‐sensitizer. The focus of this work is to examine the effects of plasmonic Au NPs and carbon dots in addition to their synergistic effect by capping the Au NPs with Cl/N‐CQDs, and track their influence in DSSCs. N719 as ruthenium‐based dye, and natural dyes including betanin, crocin, carthamin, curcumin, chlorophyll, mallow, and lawsone are selected and applied in the DSSCs co‐sensitized by Au@Cl/N‐CQDs. The power conversion efficiency (PCE) of DSSCs using all of the selected dyes is enhanced upon using the Au@Cl/N‐CQDs. It is due to the improvement in VOC (open circuit voltage) and JSC (short circuit photocurrent densities) relative to the use of dyes alone. Based on computational results, Au@Cl/N‐CQDs cause a red‐shift in comparison with pure dyes. The TD‐DFT (time‐dependent density functional theory) results show that the orbitals from the Au@Cl/N‐CQDs in dye/Au@Cl/N‐CQDs have contribution in most of the absorptions. In other words, electrons from HOMO (highest occupied molecular orbital) of Au@Cl/N‐CQDs is transferred to the LUMO (lowest unoccupied molecular orbital) of dye, in most cases.

Rapid Thermal-Driven Crystal Growth and Defect Suppression in Antimony Selenide Thin Film for Efficient Solar Cells.

Antimony selenide (Sb2Se3) has demonstrated considerable potential and advancement as a light-absorbing material for thin-film solar cells owing to its exceptional optoelectronic characteristics. However, challenges persist in the crystal growth, particularly regarding the nucleation mechanism during pre-selenization process for Sb2Se3. The defects originating from this process significantly impact the quality of the absorber layer, leading to the degradation in the power conversion efficiency (PCE) of the device. Herein, the evolution of pre-selenization using rapid thermal processing (RTP) on the crystallization quality of Sb2Se3 film is systematically investigated. By optimizing the initial nucleation process during pre-selenization, resulting in a reduction of grain boundaries and nucleation centers, the Sb2Se3 thin films demonstrate enhanced crystallinity and pinholes-free morphology. It is found that the improved quality of the grain interior and interfaces of the Sb2Se3 absorber can mitigate intrinsic defects within the bulk layer, and passivate interfacial defect recombination. As a result, the short circuit current density (JSC) is elevated to 28.97mA cm-2, and a competitive efficiency of 9.03% is achieved in Sb2Se3 device. This study provides comprehensive insight into the process of crystal growth and the mechanism for defect suppression, which holds guiding significance for advancing photovoltaic performance.

A low-cost strategy for systematically removing DC short-circuit currents in AC/DC-HDN

For any practically applied AC/DC hybrid distribution network (AC/DC-HDN), the hard issue of removing DC short-circuit currents must be solved by a cost-effective scheme. However, up to now, in the most published achievements of AC/DC-HDN, the systematic scheme to address the above issue is rarely found. This paper proposes a novel strategy with a low cost for solving this problem. The proposed strategy can: (i) greatly decrease the DC short-circuit current components flowing from the AC/DC converters to the fault point, (ii) fast switch off the paths of DC short-circuit current components from DG branches to the fault point, (iii) completely block the DC short-circuit current components that feed into the fault point from the capacitors paralleled on the DC ports of load branches. Also, in this paper, a new topology of DC/DC converter with a controlled zero-current output function is proposed for fast switching off the paths of DC short-circuit current components from DG branches to the fault point. The scheme of relay protection and automatic control matching with the proposed strategy is designed. The principles of the scheme and design are explained in detail. The simulation results verified the effectiveness of the proposed strategy are given.

Theoretical improvement of the energy conversion efficiency of an AZO/CdTe heterojunction solar cell to over 27% by incorporating FeSi2 as a second absorber layer

Abstract This paper presents the numerical analysis of cadmium telluride (CdTe) based solar cells using iron di silicide (FeSi2) as the second absorber layer and aluminum-doped zinc oxide (AZO) as the window layer. The photovoltaic performance of solar cells with Al/AZO/CdTe/FeSi2/Ni structure was analyzed and improved by SCAPS-1D software. When analyzing the influence of thickness and carrier concentration on the photovoltaic performance, it was found that the optimum values for the CdTe layer were 300 nm and 1015 cm-3, for the AZO layer they were 10 nm and 1018 cm-3, while for the FeSi2 layer they were 1 µm and 1018 cm-3. The defect density (Nt) at the AZO/CdTe and CdTe/FeSi2 interfaces was also analyzed, obtaining that the optimum value of Nt is 1010 cm-2 at both interfaces. Device optimization is achieved by obtaining a maximum Power Conversion Efficiency (PCE) of 27.22% with an open circuit voltage (Voc) of 0.63 V, a short circuit current density (Jsc) of 51.43 mA/cm2 and a fill factor (FF) of 83.06%, which makes FeSi2 a potential alternative for the development of CdTe-based solar cells due to its absorption of photons with lower energy wavelengths.

Fabrication of solid-state plasmonic solar cell device using FTO|TiO2|Ag-nanoparticle assembly to generate hot electrons surpassing Schottky barrier

This work presents a detailed investigation into the fabrication and performance evaluation of plasmonic solar cells, where a thin film of silver nanoparticles is deposited onto a TiO₂ layer, with the silver film itself functioning as the active layer for light absorption and energy conversion. The study compares two deposition techniques—DC Magnetron Sputtering and Thermal Vapor Deposition (TVD)—revealing significant differences in the resulting device performance. The device fabricated using TVD demonstrated a significantly higher open circuit voltage of 440.3 mV and short circuit current density of 1.6 mA/cm² compared to the device fabricated via DC Magnetron Sputtering, which recorded an open circuit voltage of 56.92 mV and a short circuit current density of 0.03 mA/cm². These results indicate that TVD offers superior electron-hole separation, reduced recombination losses, and enhanced light absorption efficiency. The main contribution of this work lies in demonstrating that the TVD technique significantly improves the photovoltaic performance of plasmonic solar cells compared to DC Magnetron Sputtering. The study validates the hot-electron mechanism at the TiO2|Ag junction using Kelvin probe force microscopy, contributing valuable insights into the role of plasmonic effects in enhancing solar cell efficiency. Additionally, it underscores the potential of TVD for developing advanced solar cell technologies with higher energy conversion efficiency.

Enhancement effect of biomass-derived Carbon Quantum Dots (CQDs) on the performance of Dye-Sensitized Solar Cells (DSSCs)

Corn stover, an agricultural waste, was used to prepare nitrogen self-doped carbon quantum dots (CQDs) through a simple hydrothermal method with only water at near room temperature for the first time. The surface, electrochemical, and photovoltaic characteristics of CQDs doped TiO2 in dye-sensitized solar cells (DSSCs) were thoroughly and systematically examined. The average diameter of blue-fluorescence CQDs measured by a high-resolution transmission electron microscope (HR-TEM) was 4.63 ± 0.87 nm, which consisted of polar functional groups. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy of the biomass-derived CQDs, determined by the cyclic voltammetry (CV) test, were, −5.48 eV and −3.89 eV, respectively. The negative shift of flat band potential (Vfb) in CQDs incorporated photoanode implies the fermi level shifted upward. Experimental results revealed that the improved performance of DSSCs was due to charge transport enhancement and separation, which resulted in the improved energy level configuration between TiO2, CQDs, and electrolytes. In this regard, the CQDs serve as a mediator that enables charge carrier transport without hindrance. In this study, CQDs added to TiO2 + N719, increased short circuit current density (JSC) and power conversion efficiency (PCE) value by ∼26.00 % (10.13 to 12.69 mA/cm2) and 27.20 % (4.78 % to 6.08 %), respectively.

Transmembrane Serine Protease 2 and Proteolytic Activation of the Epithelial Sodium Channel in Mouse Kidney.

The renal epithelial sodium channel (ENaC) is essential for sodium balance and blood pressure control. ENaC undergoes complex proteolytic activation by not yet clearly identified tubular proteases. Here, we examined a potential role of transmembrane serine protease 2 (TMPRSS2). Murine ENaC and TMPRSS2 were (co-)expressed in Xenopus laevis oocytes. ENaC cleavage and function were studied in TMPRSS2-deficient murine cortical collecting duct (mCCDcl1) cells and TMPRSS2-knockout (Tmprss2-/-) mice. Short-circuit currents (ISC) were measured to assess ENaC-mediated transepithelial sodium transport of mCCDcl1 cells. The mCCDcl1 cell transcriptome was studied using RNA sequencing. The effect of low-sodium diet with or without high potassium were compared in Tmprss2-/- and wildtype mice using metabolic cages. ENaC-mediated whole-cell currents were recorded from microdissected tubules of Tmprss2-/- and wildtype mice. In oocytes, co-expression of murine TMPRSS2 and ENaC resulted in fully cleaved γ-ENaC and ∼2-fold stimulation of ENaC currents. High baseline expression of TMPRSS2 was detected in mCCDcl1 cells without a stimulatory effect of aldosterone on its function or transcription. TMPRSS2 knockout in mCCDcl1 cells compromised γ-ENaC cleavage and reduced baseline and aldosterone-stimulated ISC which could be rescued by chymotrypsin. A compensatory transcriptional upregulation of other proteases was not observed. Tmprss2-/- mice kept on standard diet exhibited no apparent phenotype, but renal γ-ENaC cleavage was altered. In response to a low-salt diet, particularly with high potassium intake, Tmprss2-/- mice increased plasma aldosterone significantly more than wildtype mice to achieve a similar reduction of renal sodium excretion. Importantly, the stimulatory effect of trypsin on renal tubular ENaC currents was much more pronounced in Tmprss2-/- mice than that in wildtype mice. This indicated the presence of incompletely cleaved and less active channels at the cell surface of TMPRSS2-deficient tubular epithelial cells. TMPRSS2 contributes to proteolytic ENaC activation in mouse kidney in vivo.

Operation Analysis of Power Systems with HVDC Interconnections Using a Transient Stability Aware OPF Method

High-voltage direct current (HVDC) transmission systems are widely used today due to their several advantages over high-voltage alternative current (HVAC) systems. They are primarily utilized in connecting different large grids or smaller independent networks, especially in submarine interconnections. Many studies have been conducted globally on the optimal planning, operation, and control of these power systems. Understanding the transient stability of these systems during significant disturbances is also of great importance. This paper specifically focuses on power systems with HVDC connections and high penetration of renewable energy sources. Analytical models were developed for power system components like HVDC converters, DC lines, and full converter wind generators. A simulation of a test-case power system was conducted, including various significant disturbances such as HVDC line trips, short circuits, power unit failures, and major changes in load. The voltage and frequency stability of the system under specific operational scenarios was also examined. The results obtained indicate technical limitations and operating guidelines to avoid undesirable conditions and system failure. In conclusion, adopting short-term stability tests the optimal operation point of the system, and the limitations in the penetration by RES units can be decided.

Gulf toadfish (Opsanus beta) urinary bladder ion and water transport is enhanced by acclimation to higher salinity to serve water balance.

Marine teleosts experience ion gain and water loss in their natural habitats. Among other tissues, the urinary bladder epithelium of marine fishes has been shown to actively transport ions to facilitate water absorption. However, transport properties of the urinary bladder epithelium of marine fishes and its plasticity in altered ambient salinities is relatively under-investigated. We describe urinary bladder epithelium electrophysiology, water flux, and expressions of ion transporters in urinary bladder tissue of Gulf toadfish (Opsanus beta) acclimated to either 35 ppt or 60 ppt seawater. Water absorption in bladder sac preparations increased ~ 350% upon acclimation to 60 ppt. Increases in water transport coincided with a significant ~ 137% increase in urinary bladder tissue mucosal-to-serosal short circuit current (Isc) and a ~ 56% decrease in tissue membrane resistance. Collectively, these metrics indicate that an active electrogenic system facilitates water absorption via Na+ (and Cl-) transport in urinary bladder tissue. Furthermore, pharmacological inhibition of urinary bladder tissue Isc and expression of a suite of ion transporters and channels previously unidentified in this tissue provide mechanistic insights into the transport processes responsible for water flux. Analysis of water transport to overall Gulf toadfish water balance reveals a modest water conservation role for the urinary bladder of ~ 0.5% of total water absorption in 35 ppt and 1.9% in 60 ppt acclimated toadfish. These results emphasize that electrogenic ion transport facilitates water-absorptive properties of the urinary bladder in Gulf toadfish - a process that is regulated to facilitate water homeostasis.

Oscillation Suppression of Grid-Following Converters by Grid-Forming Converters with Adaptive Droop Control

The high penetration of renewable energy sources (RESs) and power electronics devices has led to a continuous decline in power system stability. Due to the instability of grid-following converters (GFLCs) in weak grids, the grid-forming converters (GFMCs) have gained widespread attention featuring their flexible frequency and voltage regulation capabilities, as well as the satisfactory grid-supporting services, such as inertia and damping, et al. Notably, the risk of wideband oscillations in modern power grids is increasingly exacerbated by the reduced number of synchronous generators (SGs). Thus, the wideband oscillation suppression method based on adaptive active power droop control of GFMCs is presented in this paper. First, the stability of the hybrid grid-forming and grid-following system is obtained according to the improved short circuit ratio (ISCR), where the GFMC is in parallel at the point of common coupling (PCC) of the GFLC. Then, an adaptive adjustment strategy of the active power droop control is proposed to enhance the oscillation suppression capability across the full frequency range, thereby mitigating the wideband oscillation caused by phase-locked loop (PLL) synchronization in the GFLCs. Additionally, a first-order inertia control unit is added to the active and reactive power droop controllers to mitigate frequency and voltage variations as well as suppress potential mid-to-high frequency resonance. Finally, the wideband oscillation suppression strategy is validated by the simulation and experimental results.

Enhanced Efficiency of Dye-Sensitized Solar Cells Using Nitrogen-Titanium Dioxide Composites and Optimized Azo Dye Mixtures

In response to the increasing global energy demand, developing cost-effective and reliable renewable energy sources is crucial. Dye-Sensitized Solar Cells (DSSCs) have emerged as a promising alternative due to their low production cost, flexibility, and capability to operate under diffuse sunlight. This study aims to enhance the efficiency of DSSCs by incorporating Nitrogen-Titanium Dioxide (N-TiO2) composites synthesized via the Sol-Gel method [1]. The DSSCs were constructed using N-TiO2 composites in conjunction with VC, RP, and RM azo dyes. Nitrogen in the TiO2 matrix effectively reduced the band gap, leading to improved light absorption. The presence of Nitrogen dopants is expected to introduce additional energy levels within the TiO2 bandgap, enhancing light absorption and charge carrier separation, which are crucial factors for improved DSSC performance [2,3]. The current-voltage (I-V) characteristics of the DSSCs revealed significant variations in key performance metrics, including short circuit current (Isc), fill factor, and power conversion efficiency. Specifically, DSSCs utilizing N-TiO2 with VC-RP dye mixture achieved a higher efficiency of 0.349%, an Isc of 0.85 mA, and a fill factor of 44.59%, with Rs and Rsh values of 328.13Ω and 1637.18Ω, respectively [4]. These results underscore the potential of N-TiO2 composites, particularly when paired with optimized dye mixtures, to significantly enhance the electronic properties and overall efficiency of DSSCs.