Shielded Metal Arc Welding Research Articles

Assessment of Mechanical Strength of A36 Steel with Flux Cored Arc Welding Process

Shielded Metal Arc Welding (SMAW) is a popular welding technology in the construction and industrial sectors due to its ease of use. Flux-cored arc welding (FCAW) has gained popularity in the construction sector and industrial settings. The Welding Procedure Specification (WPS) restricts material compatibility for FCAW due to systematic selection and qualification. Penetrant Testing exposes damage to welded specimens, ensuring they meet the standard. Non-Destructive Testing (NDT) and mechanical tests like tensile and bending tests determine the mechanical strength and weld characteristics of steel using FCAW. The results show the effectiveness of pWPS and satisfy the code and standard. Dye Penetrant Test results show no cracks and acceptable criteria for both side A and side B of the steel plate. Bending test results show expected yield points, but failures occur due to discontinuities in break force and failures in tensile strength.

Evaluating the Health Risks and Safety Protocols for Welders Exposed to Shielded Metal Arc Welding (SMAW) Fumes: A Systematic Literature Review

Evaluating the Health Risks and Safety Protocols for Welders Exposed to Shielded Metal Arc Welding (SMAW) Fumes: A Systematic Literature Review

Mechanical Properties and Microstructure Analysis of Mild Steel Welding Made by GTAW

This work discusses the effect of gas tungsten arc welding (GTAW) variables on the welding transverse tensile strength and hardness of S 235JR at different groove configurations. The welding microstructure and numerical fracture mechanism are also discussed. GTAW is increasingly emerging in the local industry due to its advantages over conventional shielded metal arc welding (SMAW). The properties of steel welding have always concerned manufacturers and researchers. Since steel structures experience forces such as tensile, it’s vital that good welding has increased tensile strength. It was reported that the hardness of welding affects the welding properties and, therefore, the integration of welded structures. The groove shape of the joining ends determines the size of the FZ and affects the dilution; thus, it is important to study the groove shape due to its effect on the final properties of welding. The results showed an increased welding traverse tensile strength (251 MPa) at higher welding speeds (150 mm/min) and V-shaped groove welding. The V-shaped groove welding that obtained higher tensile strength (251 MPa) has shown higher grain boundary ferrite and PF volume friction in the FZ and finer PF in the HAZ due to its higher interpass heat input. Higher traverse tensile strength welding has shown increased bainite and lower bainite volume friction in FZ and a finer grain structure in HAZ. The failure due to tensile force starts at the welding root, according to numerical analysis, and a double V-shaped groove has shown deformation balance at the tensile test.

Improving Dissimilar Metal Joining Quality Through Shielded Metal Arc Welding: A Taguchi Optimization Strategy

The results of an experiment that used an orthogonal Taguchi method to improve shielded metal arc welding (SMAW) were given. The SMAW method was used to join dissimilar metal of SPHC and St. 30. SPHC material has a low carbon steel content, while St. 30C steels contain a medium amount of carbon steel, which is used for tractor shaft axles. Carbon percentages vary slightly between the two substances. This study aimed to achieve the highest possible quality of tensile strength by utilizing the specified SMAW parameters. SPHC material has a low carbon content, whereas St. 30 steel has a moderate carbon content. This study used the Taguchi experimental method with three input variables and three experimental levels. The SNR ratio is used to evaluate the most optimal SMAW performance. ANOVA analysis is used to evaluate the most crucial parameters in determining the response variable. This research has successfully provided input on the combination of SPHC and St. 30C for SMEs. It operates effectively with a welding current of 133 A, a welding voltage of 9 V, and a filler diameter of 2.0 mm. The S/N ratio analysis found that the welding current, voltage, and filler diameter all had a significant impact on the outcome.

Effect of Welding Process on Microstructure and Mechanical Properties of Boron Containing Modified 9Cr-1Mo Steel

The influence of Shielded Metal Arc (SMA) welding and Activated Tungsten Inert Gas (A-TIG) welding on the microstructure and mechanical properties of boron containing Modified 9Cr-1Mo steel has been investigated. The tensile strengths of SMA weld joints at room temperature and 550℃ (730, 710 MPa) are higher than those of A-TIG weld joints (520, 465 MPa); whereas A-TIG welds (66, 18J) show better impact energies at room temperature and 0℃ than SMA welds (53, 12J). Creep resistances of both the weld metals, as estimated by impression creep technique are comparable; while, the A-TIG heat affected zone (HAZ) possesses higher creep resistance than the SMA HAZ. The fracture toughness of the A-TIG weld metal is inferior (64 kJ.m-2) to that of SMA weld metal (181 kJ.m-2) and brittle fracture is seen. It has been observed that the multiple passes of SMA process are advantageous in modifying the delta ferrite present in the weld metal although they cause severe damage to the HAZ microstructure.

Effect of welding parameters on microstructure and mechanical properties of dissimilar AISI 304/ductile cast iron fusion welded joints

Problems associated with dissimilar fusion welding are mainly originated from the differences in melting points, coefficients of thermal conductivity and thermal expansion, …etc., and carbon content when welding dissimilar ferrous materials. In this study, the problems associated with dissimilar fusion welding of stainless steel AISI304 with ductile cast iron DCI grade A536 were investigated. Using shielded metal arc welding (SMAW) process, various welding parameters were studied to investigate the successful/accepted dissimilar welded joint(s). Welding electrodes and welding techniques were the main studied parameters. Microstructural and mechanical investigations were carried out for welded joints under different welding parameters. Tensile, impact and hardness tests coupled with optical and scanning electron microscopic examinations with EDX analysis were made for metallurgical and mechanical evaluations of welded joints. This extensive study could solve the problem of dissimilar welding between ductile cast iron and 304 stainless steel. The main results showed that joints welded by ENiCrFe-3 electrode in root pass and ENiFe-CI in filling passes were the successful dissimilar welded joints with 422 MPa tensile strength which represents 104% of annealed DCI base metal and without any changes in toughness properties, where toughness at HAZ of DCI was 18 J. High Ni content in weld metal increased the strength, ductility and reduced the weld metal dilution.

COMPARATIVE STUDIES ON MICROSTRUCTURE AND TOUGHNESS OF 9 % Ni STEEL JOINTS WELDED BY SMAW AND GTAW

The microstructure and impact toughness of 9 % Ni steel joints welded by shielded metal arc welding (SMAW) and gas tungsten arc welding (GTAW) were investigated. The two kinds of weld metal were mainly composed of cellular dendrites and a granular precipitated phase. The grains and cellular dendrites of the GTAW weld metal were smaller than those of the SMAW weld metal. The precipitates in the SMAW weld metal were stripe-shaped while those in the GTAW weld metal were rod-shaped; the number of precipitates in the GTAW weld metal was lower than in the SMAW weld metal. The low-temperature impact toughness of the GTAW weld metal was better than that of the SMAW weld melt.

Hardness and Microstructure Characterization of Hardfacing Alloys Deposited by The Shielded Metal Arc Welding (SMAW) on AISI 1045 Medium Carbon Steel

A ring frame is a machine used for yarn production in the textile industry. Continuous use of the machine results in wear on the shaft timing pulley on the ring frame machine. To improve this condition, repairs are needed, one of which uses the hardfacing method. This study aims to determine the effect of hardfacing on the microstructure and hardness of the shaft timing pulley made from AISI 1045. The hardfacing process used the shielded metal arc welding (SMAW) method with welding current variations of 115 A, 125 A, 135 A, 145 A, and 155 A. In this study, the electrode used was AWS A5.1 E7018 with a diameter of 3.2 mm. The hardfacing product obtained was then finished with a lathe to produce a shaft with a final diameter of 30 mm. In this study, microstructure and hardness tests were carried out on specimens before and after finishing. The results of this study showed that an increase in current caused an increase in the number of pearlite phases in the weld metal and HAZ (heat-affected zone) areas. While in the base metal, the increase in current increased the number of ferrite phases. The highest hardness value was found in specimens that were hardfaced with a current of 145 A. However, the hardness of the hardfacing layer will decrease with the use of currents greater than 145 A. The hardness of the specimens with hardfacing treatment at a current of 145 A resulted in hardness in the weld metal, HAZ, and base metal of 225 HV, 209 HV, and 203 HV, respectively. After the finishing process, the weld metal, HAZ, and base metal in this specimen produced a hardness of 225 HV, 217 HV, and 208 HV, respectively.

Pitting behavior of austenitic stainless-steel welded joints with dense inclusions and methods to enhance pitting resistance

PurposeThis study aims to assess the pitting resistance of austenitic stainless steel welded joints fusion zone (FZ) with high density of inclusions before and after surface treatment, including potentiostatic pulse technique (PPT) and pickling.Design/methodology/approachThe potentiodynamic polarization tests and critical pitting temperature tests were carried out for estimating pitting resistance. The PPT and pickling were performed as surface treatment. Scanning electron microscope (SEM) and energy dispersive spectrometer were used for characterize the microstructure and elemental distribution. Electron back-scattered diffraction (EBSD) was used to assess the portion of phases and morphology of grains.FindingsThe weld metal exhibits a higher degree of alloying compared to the base metal, and it contains d-phase and sulfur-containing inclusions. Sulfur-containing inclusions serve as initiation sites for pitting, and they diminish the pitting resistance of weld metal. Both PPT and pickling can remove sulfur-containing inclusions, but PPT causes localized dissolution of the weld metal matrix around the inclusions, while pickling does not. Because of the high density of inclusions, certain pits initiated by PPT are significantly deeper, which makes the formation of stable pitting easier. Because of the high density of inclusions, certain pits initiated by the PPT are deeper. This characteristic facilitates the progression of these initial defects into fully developed, stable pits.Originality/valueAnalysis of pitting initiation in shielded metal arc welding FZ with PPT and ex situ SEM tracking observation. Explanation of why the PPT surface treatment is not able to enhance the pitting resistance of stainless steel with a high inclusion density.

Analysis of Dye-Penetrant Test, Tensile Test, and Bending Test Results of Shielded Metal Arc Welding (SMAW) on Carbon Steel ASTM A106 Grade B Pipes in 6G Welding Position at PPSDM Migas Cepu

Analysis of Dye-Penetrant Test, Tensile Test, and Bending Test Results of Shielded Metal Arc Welding (SMAW) on Carbon Steel ASTM A106 Grade B Pipes in 6G Welding Position at PPSDM Migas Cepu

Comparative study of electrogas and shielded metal arc welding processes on steel A537 welded joints

In this research, the electro-gas welding process was compared with a shielded metal arc welding process for welding steel A573 from a mechanical properties point of view. Visual and radiographic inspections confirmed the soundness of weldments produced by electro-gas welding and shielded metal arc welding techniques. Various assessments were performed, including hardness, tensile strength, V-notch impact toughness, macrostructure, microstructure, and electrochemical tests. The mechanical properties of the two welding processes were closely matched, with an average tensile strength of 590 MPa for electro-gas welding and 585 MPa for shielded metal arc welding. Furthermore, the influence of welding variables, such as groove design and heat input, on the welded joints’ quality, mechanical properties, and electrochemical behavior was thoroughly examined. Dilution estimates, particularly for the electro-gas welding process, were around 35%, and a significant similarity was observed between the chemical composition determined through dilution calculations and that obtained from chemical analysis using an arc spark emission spectrometer. Notably, the electro-gas welding process demonstrated exceptional productivity, surpassing the shielded metal arc welding process by more than elevenfold. The optimum welding parameters for the electro-gas welding process were identified to achieve superior mechanical properties, low corrosion rates, and reduced consumption of the welding electrodes. This included adopting a single V type and groove angle of 30° instead of 60°, resulting in a 23% reduction in economic costs. Selecting an appropriate heat input within the range of 12 to 14 kJ/mm further contributed to enhancing overall welding efficiency.

Experimental Investigation of Optimal Welding Parameters and Mechanical Properties of Shielded Metal Arc Welded Mild Steel Plates

This study focuses on achieving enhanced mechanical properties of the welded joints, which is critical for the applications of mild steel (MS) plates in various industries. In this regard, a systematic approach is used to adjust welding parameters such as welding current and workpiece thickness in shielded metal arc welding (SMAW), with the objective of identifying the optimal combination that maximizes weld quality. The experiments were planned with the help of Taguchi’s L9 orthogonal array method in order to reduce experimental cost and time. The weld quality is optimized by determining the signal-to-noise ratios of weld penetration, tensile strength, impact strength, and microhardness for each experimental sample. As a result, 110 A welding current is obtained as the optimal SMAW parameter for a 5 mm thick MS IS 2062 Grade B plate. This optimized result has also achieved 394.78 N/mm2 tensile strength and 53 J of impact resistance for the respective specimen. Besides, research not only enhances understanding of the SMAW process but also offers practical implications for industries requiring high-performance welded joints in MS structures. Additionally, this study can assist upcoming researchers in optimizing any existing welding procedures.

Effect of cobalt on Microstructure and toughness properties of 9Cr-1.8W-0.4Ni-xCo weld metal

In this research, microstructural characterization and mechanical properties of 9%Cr, 0.4%Ni (including W and Mo) steel weld metal with alloyed cobalt were investigated. Due to their strong creep resistance, oxidation resistance, and low thermal expansion, 9%Cr steels are used in nuclear power plants, petrochemical industries, and fossil fuel-powered power plants that operate in high temperature conditions. In this context, weld metals comprising 0.5 %, 1 % and 1.5 % cobalt and cobalt-free weld metal were produced by SMAW (shielded metal arc welding) technique. Microstructure of the weld metals were characterized with optical microscope (OM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Also, XRD analysis was performed on the bulk samples and precipitated carbide/nitride phases extracted from the weld metals. In addition, differential scanning calorimetry (DSC) was used to determine the phase transformations. Thermo-Calc modeling study was also performed. Hardness, tensile and Charpy-V impact tests were carried out to determine the mechanical properties. The hardness did not change significantly when cobalt up to 1.5 % in the weld metal. However, with the increase of cobalt, the yield and tensile strength increased without affecting the elongation value too much. In the Charpy impact tests performed at different temperatures (−40 °C, −20 °C, +20 °C, +40 °C, +60 °C), the amount of cobalt increased toughness, especially at +40 and + 60oC temperatures. Ductile brittle transformation temperature (DBTT) of the weld metal with 1.5 % Co decreased from 29 °C to 15 °C compared to cobalt free weld metal. It is thought that this may be caused by the further separation of C, Cr and W from the matrix through forming precipitate by the cobalt effect. Besides the mechanical properties, microstructure was also affected by adding Co with inhibition of delta ferrite formation which decrease the toughness. Curie temperature increased with increasing cobalt content detected by DSC.

Pengaruh Perbedaan Ayunan Pengelasan Dengan Metode SMAW Terhadap Kekuatan Tarik Pada Baja ST 37 Strip 5 MM

The purpose of this study was to see the effect of differences in welding swing on the tensile strength of 5 mm strip iron. The number of research samples was 6 pieces divided into two groups, the first group of 3 pieces welded with zig-zag welding swing, the second group of 3 pieces welded with spiral welding swing. The tensile test object used a tensile testing machine to determine the tensile stress value of the welding swing of each test object by slowly applying a load or force until the test object broke. This research method uses quantitative with a comparative experimental approach. The results of the welding tensile stress test of each test object sample welded with zig-zag and spiral welding swing joints showed that there was a similarity in the tensile test data, namely normal distribution, and similarity in variance. Hypothesis testing was obtained from the results of the tensile stress test of SMAW welding results with zig-zag and spiral welding swings showing a Tcount value of -8.021 (dk) = n1 + n2-2 at a significance level of 0.01 or 1%, a Ttable of 4.604 was obtained. So that the magnitude of the tensile stress of SMAW welding results with zig-zag and spiral welding swings has no significant influence.

Comparative Study of Electron Beam Welding and Shielded Metal Arc Welding of 30CrMnSiNi2A Thick Wall Cylinder

Comparative Study of Electron Beam Welding and Shielded Metal Arc Welding of 30CrMnSiNi2A Thick Wall Cylinder

The Effect of Preheating and Current on the Development of Mild Steel Clad Layers via Stick Welding

The Effect of Preheating and Current on the Development of Mild Steel Clad Layers via Stick Welding

Study the Corrosion Behavior of Low Carbon Steel Weldments Immersed in Tap Water

Corrosion is one of the main sources of failure for metals and alloys, thus it is a major engineering problem. Engineers must consider the corrosion of metals in different environments when designing engineering parts. Metals tend to corrode in different media; they show different behaviors due to differences in chemical composition and the severity of the corrosive medium. In tap water, the corrosion of mild steel products is an electrochemical phenomenon that includes two reactions: the dissolving of iron (anodic) and the reduction of oxygen (cathodic). This work observes the corrosion behavior of welded low-carbon steel by Friction Welding (FW), Shielded Metal Arc Welding (SMAW) , and MIG welding techniques using immersion tests in tap water at different periods. The results revealed that while the corrosion rate of Base Metal (BM) increases, it reaches a nearly steady state in the friction-welded and SMAW-welded samples. The difference in the corrosion rate of the welded samples can be attributed to changes in the concentrations of Cl– and CaCO3 ,as well as the pH values of the corrosive mediums. Pits could be observed in the microstructure of the nugget zone for all weldments.

Nichrome Dependency in Welding Layer Using In situ Fabrication on Hardness and Corrosion Properties

The use of shielded metal arc welding (SMAW) equipment to synthesize alloys is one of the most promising methods as it can be used for in-situ fabrication. The hardness and corrosion properties of the deposited layer during the welding process can be enhanced by dilution of nichrome (NiCr) during the process. Therefore, the alloy was synthesized on the surface of the mild steel using SMAW equipment with various NiCr additions. The properties of the alloy were investigated using an X-ray diffraction (XRD), an Optical microscope, a Potentiostat, and a Vickers hardness apparatus. The appearance of martensite overlaps with the ferrite phase could be affected by the addition of NiCr to the alloy. An increase in NiCr content is followed by an increase in the lattice parameter value of the ferrite phase. The presence of a certain amount of nickel (Ni) contributes to the formation of lower transformation phases, including martensite. At the same time, the incorporation of chromium (Cr) also plays a significant role in promoting the formation of acicular ferrite. An increase in NiCr content in NiCr2 and NiCr3 samples results in a quantitative increase in martensite formation. Adding 0.434 g of NiCr to the weld deposited layer could result in the corrosion rate of the alloy being 0.1118 mm/y. Higher hardness is found in the NiCr3 sample, around 742.06 HV.

Towards Improving Welding Skills: Creating Innovative Modules For Teaching SMAW Integrated 3D Animation

This research aims to develop teaching modules on welding techniques in vocational schools using the problem-based learning (PBL) model, a scientific learning approach, and an authentic assessment of welding competency using the manual arc welding or SMAW welding process. The development of teaching modules at vocational schools will improve the quality of the process and the quality of learning outcomes for SMAW welding engineering subjects at vocational schools. This research uses a development research method with a research design using design-based research (DBR), which refers to the instructional design model (IDM) development model design. The participants involved in this research were class XI vocational school students in East Java. The module validity test assessment results have an average score of 3.8 in the very valid category. The SMAW welding technique module that has been prepared can be used to implement SMAW welding technique learning at vocational schools. The teaching module evaluation stage results show an outstanding category, which means that the teaching module developed meets practical requirements. All students' average normalized gain score (<g>) was 0.72, included in the high improvement category. The results of observations of the implementation of the PBL model facilitated by teaching modules from two observers were analyzed using percentages of agreement (PA). The conclusion of the research shows that the teaching module developed is valid, practical, and effective.

Creep cavities and carbide evolution in interrupted creep conditions along P91 steel of dissimilar weld joint

The creep behaviour of dissimilar weld joint of 316LN SS-P91 steel when subjected to lower applied stresses (below 100 MPa) generally fails in a Type-IV pattern. The dissimilar weld joint was welded through shielded metal arc welding (SMAW) process with INCONEL as electrode, a nickel-based superalloy. An interrupted creep test was carried out at creep condition of 80 MPa −600 °C temperature. Interruption was done at two stages of creep, i.e. (a) mid of secondary and (b) start of tertiary. Microstructural evolution with respect to the hardness variation along various regions of P91 steel at interrupted and the failed specimen was done. A coarsening of hierarchical boundaries and M23C6 carbides was observed along HAZ region that has resulted with respect to time and temperature.