Separation Of Particles Research Articles

Results and Perspectives of Timepix Detectors in Space—From Radiation Monitoring in Low Earth Orbit to Astroparticle Physics

In space application, hybrid pixel detectors of the Timepix family have been considered mainly for the measurement of radiation levels and dosimetry in low earth orbits. Using the example of the Space Application of Timepix Radiation Monitor (SATRAM), we demonstrate the unique capabilities of Timepix-based miniaturized radiation detectors for particle separation. We present the incident proton energy spectrum in the geographic location of SAA obtained by using Bayesian unfolding of the stopping power spectrum measured with a single-layer Timepix. We assess the measurement stability and the resiliency of the detector to the space environment, thereby demonstrating that even though degradation is observed, data quality has not been affected significantly over more than 10 years. Based on the SATRAM heritage and the capabilities of the latest-generation Timepix series chips, we discuss their applicability for use in a compact magnetic spectrometer for a deep space mission or in the Jupiter radiation belts, as well as their capability for use as single-layer X- and γ-ray polarimeters. The latter was supported by the measurement of the polarization of scattered radiation in a laboratory experiment, where a modulation of 80% was found.

Occupation-Dependent Particle Separation in One-Dimensional Non-Hermitian Lattices.

We unveil an exotic phenomenon arising from the intricate interplay between non-Hermiticity and many-body physics, namely, an occupation-dependent particle separation for hardcore bosons in a one-dimensional lattice driven by unidirectional non-Hermitian pumping. Taking hardcore bosons as an example, we find that a pair of particles occupying the same unit cell exhibit an opposite non-Hermitian pumping direction to that of unpaired ones occupying different unit cells. By turning on an intracell interaction, many-body eigenstates split in their real energies, forming separable clusters in the complex energy plane with either left-, right-, or bipolar-types of non-Hermitian skin effect (NHSE). The dependency of skin accumulating directions on particle occupation is further justified with local sublattice correlation and entanglement entropy of many-body eigenstates. Dynamically, this occupation-dependent NHSE manifests as uni- or bidirectional pumping for many-body initial states, allowing for spatially separating paired and unpaired particles. Our results unveil the possibility of designing and exploring novel non-Hermitian phases originated from particle nonconservation in subsystems (e.g., orbitals, sublattices, or spin species) and their spatial configurations.

Microplastic separation and enrichment in microchannels under derivative electric field gradient by bipolar electrode reactions

The decomposed plastic products in the natural environment evolve into tiny plastic particles with characteristics such as small size, lightweight, and difficulty in removal, resulting in a significant pollution issue in aquatic environments. Significant progress has been made in microplastic separation technology benefiting from microfluidic chips in recent years. Based on the mechanisms of microfluidic control technology, this study investigates the enrichment and separation mechanisms of polystyrene particles in an unbuffered solution. The Faraday reaction caused by the bipolar electrodes changes the electric field gradient and improves the separation efficiency. We also propose an evaluation scheme to measure the separation efficiency. Finite element simulations are conducted to parametrically analyze the influence of applied voltages, channel geometry, and size of electrodes on plastic particle separation. The numerical cases indicate that the electrode-installed microfluidic channels separate microplastic particles effectively and precisely. The electrodes play an important role in local electric field distribution and trigger violent chemical reactions. By optimizing the microchannel structure, applied voltages, and separation channel angle, an optimal solution for separating microplastic particles can be found. This study could supply some references to control microplastic pollution in the future.

Particulate filtration by cryogenic condensation using a high efficiency Stairmand cyclone separator

This paper describes the synergy of a high-efficiency Stairmand cyclonic separator and the phenomenon of condensation generated by the low temperatures of the mixture of liquid nitrogen and ethanol, to increase the separation efficiency on particles with diameters of 1 μm, 45 μm, 75 μm, 150 μm and 250 μm. The cyclone separator adds the phenomenon of condensation, generating a film of liquid water on its internal walls. The film of liquid water causes a loss of kinetic energy in the particles, reducing their speed and becoming stuck. Al2O3 particles and pozzolana rock particles are used to perform the particle separation experimental tests. A computational fluid dynamics analysis using the second order RSM model is incorporated to describe the fluid dynamic behavior of the particles within the separator cyclone. The results in computational fluid dynamics show the agglomeration of larger diameter particles near the internal walls. Using condensation as a phase change generated by cryogenic mixing results in an overall particle separation efficiency of 76.00 %, standing for an increment of 70.14 % in comparison to a conventional high-efficiency Stairmand separator cyclone.Technological innovation: Particles, filtration, separation, condensation, cryogenic.

Seasonal charge distributions of submicron atmospheric particles in Yokohama, Japan

Charge distribution measurements are required to understand the spatiotemporal distribution of the number concentrations of submicron atmospheric particles that affect radiative forcing and particle deposition in human airways. The number concentrations of non-charged and charged particles within the 0.3–0.5 μm diameter (D) range were measured at Keio University in Yokohama, Japan, from June 2022 to January 2023 by combining a parallel-pate particle separator and optical particle counters to investigate critical parameters controlling the charging state of submicron atmospheric particles. The measurement uncertainties in the average charge number per particle (pave) and the standard deviation (1σ), derived from the charge distribution of the submicron particles, were within 15%. The monthly median values of 1σ increased in summer and decreased in winter and correlated with the water vapor amount and wind speed. The 1σ values in summer and winter, derived from the seasonally averaged charge distributions of particles, were close to those from the theoretically calculated charge distribution of particles within 0.387–0.5 μm D range and with D = 0.3 μm, respectively, suggesting that the observed particle charge distributions approached the stationary charge distribution for the effective D. In summer, the frequent transport of water molecules and ions from the Pacific Ocean causes efficient collisions between multiple ions and submicron particles with a larger effective D, which may expand the charge distribution of particles. The polarity ratio, the concentration of positively charged particles relative to that of negatively charged particles, was almost unity, indicating the well-balanced charge polarity of the submicron atmospheric particles. The polarity ratio and pave changed significantly during lightning events, indicating that the atmospheric particle charge balance broke. Our findings show that the charge distribution of submicron atmospheric particles can be partly controlled by meteorological parameters (e.g., absolute humidity) and the microphysical properties of the particles.

Evaluation of Fe-Ni Composite Oxygen Carrier in Coal Chemical Looping Gasification

Although coal chemical looping gasification (CCLG) is a promising technology for the efficient utilization of coal, limited studies concerned about the industrial application of oxygen carrier in CCLG system owing to its performance requirements including high reactivity with solid fuel, high carbon conversion, and good mechanical property. To meet the requirements of oxygen carriers in CCLG system, novel Fe-Ni composite oxygen carrier (OC) samples were successfully prepared. The performances of these OCs were evaluated in a fixed bed reactor, where they were reduced by solid fuel and then fully oxidized by air. Both fixed bed tests and thermodynamic analysis showed that the prepare OCs exhibited high reactivity with coal and syngas selectivity, making them suitable for the CCLG process. Specifically, when the loading amount of NiO was 20 wt%, the Fe-Ni composite OCs achieved the highest carbon conversion (93.03%) and synthesis gas selectivity (73.29%). Additionally, the thermogravimetric data revealed that the Curie temperature of the OCs was higher than 550°C, making them suitable for magnetic separation of the OC particles and carbon residue in the CCLG system.

On-chip label-free sorting and enrichment of microplastic particles by using deterministic lateral displacement

A novel deterministic lateral displacement (DLD) method employing a pressure-driven flow for the continuous size-based separation of microplastic particles is presented in this paper. To induce the DLD effect, arrays of triangular posts were designed to enhance the sorting resolution and reduce the particles clogging. For the particles with a diameter larger than the critical diameter (Dc) in the DLD device, they move in bump mode with collision to microposts. While, the particles flow in zigzag mode if their sizes are below the Dc value. The DLD microfluidic chip enables simplified fabrication process and shows property of label-free and high throughput. Numerical studies were conducted to discuss the Dc values in the microchannel with horizontally symmetrical and asymmetrical posts, where Dc was found smaller in the asymmetric horizontal flow, enabling higher separation sensitivity and resolution. Experiments were conducted to demonstrate the separation of 10 μm and 15 μm polystyrene microplastic particles, and different types of polystyrene and polyethylene microplastic particles by adjusting the flow rates. In order to achieve successful separation, the flow rates between the sheath flow and the sample solution were well matched. In this way, the proposed DLD microfluidic chip with horizontally asymmetrical triangular posts shows property of label-free, high throughput, capability to analyze microplastic particle selectively and sensitively, possibility of sorting nanoplastic particles.

Effect of fluidized bed shapes on gas-solid fluidization characters and flow regime transition

The technology of gas-solid dense-phase fluidized bed separation is applied in the separation of fine particles in minerals due to its stable and reliable characteristics. The experiment collected time-domain distribution signals of pressure drop from fluidized beds with different shapes, systematically analyzed the spatiotemporal distribution characteristics of bed density, and studied the effects of bed shape and fluidization number N on the fluidization and flow transition of the bed layer. The results indicate significant differences in Umf among fluidized beds with different shapes, and the tapered bed requires the highest energy for fluidization. When N=1.3, the cylindrical bed layer is the most stable, maintaining an average density of 1.8 g/cm3, with a density fluctuation variance of 0.02 g/cm3. Additionally, when N<1.0, almost no bubbles inside the bed layer. With an increase in gas velocity, the time-domain distribution of pressure drop signals shows different degrees of fluctuation. When N=1.1, Conspicuous non-uniform particle flow is evident in the tapered bed, with a bubble main frequency of 8 Hz, an amplitude of 27.1, and the highest pressure drop energy signal, indicating that the tapered bed enters the bubbling state prematurely. Finally, fine coal separation experiments were conducted, and the results showed that the minimum E value for the cylindrical bed is 0.08 g/cm3, while the maximum E value for the tapered bed is 0.17 g/cm3.

Rapid separation of MOFs particles with the aid of PVDF hollow fiber membrane

Metal-organic frameworks (MOFs) have been widely investigated due to their fascinating structures and properties. However, the time-cost synthetic process and the difficult separation from liquid phase hinder their practical application. In this study, a self-made automatic apparatus containing commercial poly(vinylidene fluoride) (PVDF) hollow fiber membranes was used to separate MOFs from large-volume suspension. Taking MIL-88A(Fe) synthesized with industrial-grade chemicals as an example, the investment cost, operation cost, human cost, time duration during separation process, and unit cost price of MIL-88A(Fe) were significantly reduced by 62%, 82%, 100%, 90%, and 36%, respectively, compared to those of centrifugation. More importantly, MIL-88A(Fe) powders that were separated and purified by the apparatus were easy to be removed from membrane surface by slight vibration, which displayed good morphology, crystallinity, as well as high degradation efficiency toward organic contaminants via photo-Fenton reaction. Meanwhile, the membrane can be reused instantly without any rinse. More encouragingly, this method is applicable to other MOFs’ separation, like ZIF-8 and ZIF-67. This study further confirmed the potential and prospective of high-throughput production and facile separation of MOFs for practical applications.

Nanocellulose-based membranes with pH- and temperature-responsive pore size for selective separation

Smart gating membranes have drawn much attention due to the controllable pore structure. Herein, a smart gating membrane with dual responsiveness was prepared from bacteria cellulose (BC) grafted with pH- and temperature-responsive polymers. By external stimulation, the average pore size of the membrane can be controlled from 33.75 nm to 144.81 nm, and the pure water flux can be regulated from 342 to 2118 L·m−2·h−1 with remarkable variation in the pH range of 1–11 and temperature range of 20–60 °C. The adjustability of pore size is able to achieve the gradient selective separation of particles and polymers with different sizes. In addition, owing to the underwater superoleophobicity and the nanoscale pore structure, the membrane separation efficiencies of emulsified oils are higher than 99 %. Moreover, the controllable pore size endows the membrane with good self-cleaning performance. This nanocellulose-based smart gating membrane has potential applications in the fields of controllable permeation, selective separation, fluid transport, and drug/chemical controlled release systems.

Investigation into Detection Efficiency Deviations in Aviation Soot and Calibration Particles Based on Condensation Particle Counting

Aviation soot constitutes a significant threat to human well-being, underscoring the critical importance of accurate measurements. The condensation particle counter (CPC) is the primary instrument for quantifying aviation soot, with detection efficiency being a crucial parameter. The properties of small particles and the symmetry of their growth pathways are closely related to the detection efficiency of the CPC. In laboratory environments, sodium chloride is conventionally utilized to calibrate the CPC’s detection efficiency. However, aviation soot exhibits distinctive morphological characteristics compared to the calibration particles, leading to detection efficiencies obtained from calibration particles that may not be applicable to aviation soot. To address this issue, a quantitative study was performed to explore the detection efficiency deviations between aviation soot and calibration particles. The experiment initially utilized a differential mobility analyzer to size select the two types of polydisperse particles into monodisperse particles. Subsequently, measurements of the separated particles were performed using the TSI Corporation’s aerosol electrometer and a rigorously validated CPC (BH-CPC). These allowed for determining the detection efficiency deviation in the BH-CPC for the two types of particles at different particle sizes. Furthermore, the influence of the operating temperature of the BH-CPC on this detection efficiency deviation was investigated. The experimental results indicate a significant detection efficiency deviation between aviation soot and sodium chloride. In the range of 10–40 nm, the absolute detection efficiency deviation can reach a maximum of 0.15, and the relative deviation can reach a maximum of 0.75. And this detection efficiency deviation can be reduced by establishing a relevant relationship between the detection efficiency of the operating temperature and the calibration temperature. Compared to the saturated segment calibration temperature of 50 °C, the aviation soot detection efficiency is closer to the sodium chloride detection efficiency at the calibration temperature of 50 °C when the saturated segment operates at a temperature of 45 °C. These studies provide crucial theoretical guidance for enhancing the precision of aviation soot emission detection and establish a foundation for future research in monitoring and controlling soot emissions within the aviation sector.

ПРОГНОЗИРОВАНИЕ ИЗНОСОСТОЙКОСТИ ПАР ТРЕНИЯ СКОЛЬЖЕНИЯ

The necessity to predict optimal wear resistance of sliding couplers at the design stage is grounded. A tribological analysis of the wear of sliding couplers is carried out during the entire period of operation in various modes corresponding to the following stages: start-up, steady-state wear and shutdown. The existing approaches to solving contact problems in the interaction of solids, taking into account physico-mechanical processes in the surface layers of couplers during their wear, are analyzed. A wear model is proposed based on the destruction of the contacting surfaces of a coupler with the separation of particles, which size varies depending on the load characteristics, physico-mechanical and structural parameters, thermal properties, quality of the lubricant, etc. The results of testing prototypes for wear resistance and numerical implementation of the proposed model for predicting the wear resistance of a sliding coupler with similar characteristics are presented. It is found out that the proposed wear model makes it possible to predict (calculate) the wear resistance of a sliding coupler in a certain range by changing the initial data, thereby eliminating the need for rather laborious tests of couplers for wear under the influence of various factors.

Dielectrophoretic Particle Chromatography: From Batch Processing to Semi-Continuous High-Throughput Separation

The development of highly selective separation processes is a focus of current research. In 2016, the German Science Foundation funded a priority program SPP 2045 “MehrDimPart—highly specific multidimensional fractionation of fine particles with technical relevance” that aims to develop new or enhance existing approaches for the separation of nano- and micrometer-sized particles. Dielectrophoretic separators achieve highly selective separations of (bio-)particles in microfluidic devices or can handle large quantities when non-selective separation is sufficient. Recently, separator designs were developed that aim to combine a high throughput and high selectivity. Here, we summarize the development from a microfluidic fast chromatographic separation via frequency modulated dielectrophoretic particle chromatography (DPC) toward a macrofluidic high throughput separation. Further, we provide a starting point for future work by providing new experimental data demonstrating for the first time the trapping of 200 nm polystyrene particles in a dielectrophoretic high-throughput separator that uses printed circuit boards as alternatives for expensive electrode arrays.

Enhancing particle focusing: a comparative experimental study of modified square wave and square wave microchannels in lift and Dean vortex regimes

Serpentine microchannels are known for their effective particle focusing through Dean flow-induced rotational effects, which are used in compact designs for size-dependent focusing in medical diagnostics. This study explores square serpentine microchannels, a geometry that has recently gained prominence in inertial microfluidics, and presents a modification of square wave microchannels for improved particle separation and focusing. The proposed modification incorporates an additional U-shaped unit to convert the square wave microchannel into a non-axisymmetric structure, which enhances the Dean flow and consequently increases the Dean drag force. Extensive experiments were conducted covering a wide range of Reynolds numbers and particle sizes (2.45 µm to 12 µm). The particle concentration capability and streak position dynamics of the two structures were compared in detail. The results indicate that the modified square-wave microchannel exhibits efficient particle separation in the lower part of the Dean vortex-dominated regime. With increasing Reynolds number, the particles are successively focused into two streaks in the lift force-dominated regime and into a single streak in the Dean vortex-dominated regime, in this modified square wave geometry. These streaks have a low standard deviation around a mean value. In the Dean vortex-dominated regime, the location of the particle stream is highly dependent on the particle size, which allows good particle separation. Particle focusing occurs at lower Reynolds numbers in both the lift-dominated and lift/Dean drag-dominated regions than in the square wave microchannel. The innovative serpentine channel is particularly useful for the Dean drag-dominated regime and introduces a unique asymmetry that affects the particle focusing dynamics. The proposed device offers significant advantages in terms of efficiency, parallelization, footprint, and throughput over existing geometries.

Motility-induced phase separation of soft active Brownian particles

Motility-induced phase separation (MIPS) is the hallmark of non-equilibrium phase transition in active matter. Here, by means of Brownian dynamics simulations, we determine the phase behavior and the critical point for phase separation induced by motility of a two-dimensional system of soft active Brownian particles, whose interaction is modeled by the generalized purely repulsive Weeks–Chandler–Andersen potential. We refer to this model as soft active Brownian particles. We determine and analyze the influence of particle softness on the MIPS and show that the liquid–gas coexistence region is wider, the softer the interparticle interactions becomes. Moreover, the critical value of the self-propulsion velocity at which diluted and dense phases start to coexist also increases; as a consequence, the softer the particle interaction is, the bigger self-propulsion velocities are needed in order to observe a MIPS.

Lab-based Martian analogue experiments investigating electric and magnetic fields of dust devils

Dust devils – rotating vortices of lofted particulates formed by convection from solar heating - are a prevalent aspect of Martian weather.Within a dust devil, particles become charged though triboelectrification, and observations of terrestrial dust devils have revealed electric and magnetic fields. Understanding the behaviour of these aeolian events is vital for mission planning and duration, for example, with the Insight lander as a prime example of a mission cut short due to obscuration of solar panels by lofted dust, which is highly likely to be charged. Charged dust devils on Mars strongly imply the existence of electric discharges due to the low breakdown field. The existence of discharges would in turn imply a global electric circuit on the planet – with implications for organic chemical formation and methane losses.This work presents a laboratory-based experimental set up for investigation into both electric and magnetic fields and the feasibility of using Martian analogue dust as alternative to in-situ measurements. In a dust devil, there are two main driving motions – a vertical separation of small and large particles, and the characteristic tight spiralling motion. The experimental set-up splits these components, allowing investigation into each. It is made up of a carefully designed cylindrical tank into which dusts or powders can be dropped to allow triboelectric charging as they fall under gravity. The base of the tank has a Faraday cup for charge measurement and there is also a field mill looking into the tank from the top. The rotational component is achieved using a paddle arrangement for samples placed in the base of the tank. Electric and magnetic fields have successfully been detected from charged dust with this system.

A two-layer Timepix3 stack for improved charged particle tracking and radiation field decomposition

Abstract We characterize a novel instrument designed for radiation field decomposition and particle trajectory reconstruction for application in harsh radiation environments. The device consists of two Timepix3 assemblies with 500 µm thick silicon sensors in a face-to-face geometry. These detectors are interleaved with a set of neutron converters: 6LiF for thermal neutrons, polyethylene (PE) for fast neutrons above 1 MeV, and PE with an additional aluminum recoil proton filter for neutrons above ∼4 MeV. Application of the coincidence and anticoincidence technique together with pattern recognition allows improved separation of charged and neutral particles, their discrimination against γ-rays and assessment of the overall directionality of the fast neutron field. The instrument's charged particle tracking and separation capabilities were studied at the Danish Center for Particle Therapy (DCPT), the Proton Synchrotron, and Super Proton Synchrotron with protons (50–240 MeV), pions (1–10 GeV/c and 180 GeV/c). After developing temporal and spatial coincidence assignment methodology, we determine the relative amount of coincident detections as a function of the impact angle, present the device's impact angle resolving power (both in coincidence and anticoicidence channels). The detector response to neutrons was studied at the Czech Metrology Institute (CMI), at n_ToF and the Los Alamos Neutron Science Center (LANSCE), covering the entire spectrum from thermal up to 600 MeV. The measured tracks were assigned to their corresponding neutron energy by application of the time of flight technique. We present the achieved neutron detection efficiency as a function of neutron kinetic energy and demonstrate how the ratio of events found below the different converters can be used to assess the hardness of the neutron spectrum. As an application, we determine the neutron content within a PMMA phantom just behind the Bragg-peak during clinical irradiation condition with protons of 160 MeV.

Geometry for low-inertia aerosol capture: Lessons from fog-basking beetles.

Water in the form of windborne fog droplets supports life in many coastal arid regions, where natural selection has driven nontrivial physical adaptation toward its separation and collection. For two species of Namib desert beetle whose body geometry makes for a poor filter, subtle modifications in shape and texture have been previously associated with improved performance by facilitating water drainage from its collecting surface. However, little is known about the relevance of these modifications to the flow physics that underlies droplets' impaction in the first place. We find, through coupled experiments and simulations, that such alterations can produce large relative gains in water collection by encouraging droplets to "slip" toward targets at the millimetric scale, and by disrupting boundary and lubrication layer effects at the microscopic scale. Our results offer a lesson in biological fog collection and design principles for controlling particle separation beyond the specific case of fog-basking beetles.

Instrument with an ultra-wide dynamic detection range for the optical counting and sizing of individual particles in suspensions.

The characterization of dispersions, suspensions, and emulsions is important in a wide range of scientific applications and industries. Samples can consist of different materials and a wide range of particle sizes and concentrations. A single particle sizing and counting instrument with a dynamic detection range of ≥6 decades has been developed to detect single nano- and microparticles in aqueous suspensions based on light scattering measured in two directions. Hydrodynamic focusing is employed for particle separation and to provide stable conditions for light scattering detection. This gives the advantage of size resolution in the nm range, allowing, e.g., number based size distributions, classification of nanomaterials, determination of particle agglomerates, developments for dispersion stability analysis, or cutoff of filter media. In addition, concentration determination is based on sample volume measurement with <20 nl measurement uncertainty. We present results of particle detection in a size range from approximately above 40 nm for gold nanoparticles to 8μm for polystyrene particles using a prototyped instrument of the LUMiSpoc® series produced by LUM GmbH. The data obtained demonstrate the advantages of single-particle detection, particularly for characterizing polydisperse systems, such as precise particle sizing in the nanometer range through light scattering intensity based on Mie scattering theory. In addition, we present particle concentration data based on the integrated measurement of sample volume, which allows particle concentration to be determined with an uncertainty of 2.5% (95% confidence interval). To achieve such small uncertainties, dilution series measurements must be used to correct for coincidence losses and particle adhesion.

Repeating flaring activity of the blazar AO 0235+164

Context. Blazar AO 0235+164, located at a redshift of z = 0.94, has undergone several sharp multi-spectral-range flaring episodes over recent decades. In particular, the episodes that peaked in 2008 and 2015, which were subject to extensive multi-wavelength coverage, exhibited an interesting behavior. Aims. We study the actual origin of these two observed flares by constraining the properties of the observed photo-polarimetric variability as well as of the broadband spectral energy distribution and the observed time-evolution behavior of the source. We use ultra-high-resolution total-flux and polarimetric very-long-baseline interferometry (VLBI) imaging. Methods. The analysis of VLBI images allowed us to constrain kinematic and geometrical parameters of the 7 mm jet. We used the discrete correlation function to compute the statistical correlation and the delays between emission at different spectral ranges. The multi-epoch modeling of the spectral energy distributions allowed us to propose specific models of the emission; in particular, with the aim to model the unusual spectral features observed in this source in the X-ray region of the spectrum during strong multi spectral-range flares. Results. We find that these X-ray spectral features can be explained by an emission component originating in a separate particle distribution than the one responsible for the two standard blazar bumps. This is in agreement with the results of our correlation analysis, where we did not find a strong correlation between the X-ray and the remaining spectral ranges. We find that both external Compton-dominated and synchrotron self-Compton-dominated models are able to explain the observed spectral energy distributions. However, the synchrotron self-Compton models are strongly favored by the delays and geometrical parameters inferred from the observations.