Sensor MAC Protocol Research Articles

솔라셀 작동 모드와 센서 MAC 프로토콜의 Active 및 Sleep 모드를 고려한 전력 생산 및 공급 제어

솔라셀의 동작 상태와 센서 MAC 프로토콜의 Active 및 Sleep 동작 모드를 고려하여 충전배터리와 센서통신장치의 입력 전원을 제어하는 회로를 설계한다. 솔라셀과 재충전 배터리를 단순 조합하는 센서통신장치는 햇빛이 없는 시간이 장기간 지속될 때 배터리 소모가 많아서 작동을 멈추게 된다. 일반적으로 센서 MAC 프로토콜은 전력소모를 줄이기 위하여 짧은 Active모드와 전력 소모가 거의 없는 긴 Sleep모드를 반복한다. 이러한 특성을 고려하여, 햇빛이 충분하고 Sleep모드이면 배터리를 충전하고 햇빛이 불충분하고 Active모드이면 배터리 전력을 사용하도록 설계함으로써 배터리 지속 시간을 크게 향상시켰다. 또한, 센서통신장치는 솔라셀의 출력전력값의 크기에 따라서 솔라셀과 배터리 사이에서 입력 전원을 스위칭 하도록 하였다. 스위칭 도중에 일시적 전원 차단으로 인한 마이크로프로세서의 리셋을 방지하기 위하여 커패시터를 사용하였다. 또한, 커패시터는 Sleep모드에서 전원을 공급한다. 실험을 통하여 본 센서통신장치가 장기간의 햇빛이 없는 경우에도 안정적으로 작동한다는 것을 입증하였다. We design a control circuit that can switch input power between a rechargeable battery and a sensor communication device (mote) depending on the operating state of a solar cell as well as the active and sleep mode of a sensor MAC protocol. A mote that simply combines a solarcell and a rechargeable battery may die if there is not sunlight long. A battery is recharged if sunlight is sufficient and a device is in a sleep mode, and it supplies power if sunlight is low and the mote is in an active mode. A mote can switch its input power between solar cell and battery depending on the output level of a solar cell. During this switching, a mote may lose its state information due to the reset of a microprocessor by the transient power-off. A capacitor is used to cope with this phenomenon and also supplies power to a mote during a sleep mode. Experimental results show that the solar cell based mote operates in a very stable manner against the lack of sunlight long.

Optimal Hop Extended MAC protocol for wireless sensor networks

In wireless sensor MAC protocols, duty cycling has been exploited to put sensor nodes into sleeping state most of the time, thereby saving the limited battery efficiently. In this paper, we present a MAC protocol called Hop Extended MAC (HE-MAC) that enables a source node to transmit a data packet for multiple hops in a single duty cycle. It employs an EXP (Explorer) frame to set up the path for multiple hop transmission, which contains the information about the maximum number of hops that a packet can travel through in a single duty cycle. Using this information and an internal state of Ready-to-Receive (RTR), HE-MAC relays the packet beyond the termination of the data period. Along with our adaptive sleeping method, it additionally reduces power consumption. Then, we analytically obtain the packet latency of HE-MAC and find its optimal wakeup duration with respect to packet latency. Through ns-2 simulations, we observe that HE-MAC achieves 42.2% less power consumption and 23.6% less packet delay on average compared to RMAC [9] for a random topology of 300 nodes. With the allocated optimal wakeup duration, the latency of HE-MAC is reduced by 54.3% at maximum and 41.1% on average, compared to the case of default setting.

Energy Efficient Scheduling Algorithm for S-MAC Protocol in Wireless Sensor Network

In Sensor-MAC (S-MAC) protocol, a node located between two or more virtual clusters is called boarder node that adopts different listen and sleep schedules. These border nodes consume a large amount of energy as they switch to the listening mode often due to diversified scheduling which in turns decreases the lifetime of the wireless sensor network. This paper proposed a new unified scheduling method to solve the diversified scheduling problem of border nodes in S-MAC and evaluated the performance through simulation. It has been observed from the simulated results that the border nodes have consumed less power in case of large network as well as small networks.

Flow-Specific Medium Access for Networked Satellite System

Prior work in modeling the satellite-based detection and tracking components of the ballistic missile defense system as a large-scale, wireless sensor network relies on a medium access scheme that can accommodate the large propagation delays encountered in these networked satellite systems. While existing satellite-based systems typically employ a form of time division multiple access, recent efforts have begun to explore contention-based approaches. In this work, we quantify the effect of the large propagation delays on both contention-based and contention-free solutions and propose a flow-specific medium access solution that provides improved delay performance by dynamically adapting the networked satellite medium access scheme to changes in both individual flow and link characteristics. A comparison with CSMA and TDMA is provided through simulation results using a version of the traffic-adaptive cooperative wireless sensor medium access control protocol that has been modified to accommodate large propagation delays.

Medium reservation based sensor MAC protocol for low latency and high energy efficiency

In this paper, we present a new MAC protocol satisfying with both high energy efficiency and low transmission latency at the same time over wireless sensor network, named as medium reservation preamble based MAC (MRPM). Unlike other synchronized duty cycle MACs, MRPM does not have separate time frames for SYNC and data traffics. Both traffics are integrated in a short listen period. Also, the channel contention is excluded from listen period and transferred to new period called contention period. The contention period precedes the listen period, and only transmitters wake up in this contention period and contend for medium reservation, whereas non-transmitters bypass it. These approaches enable MRPM to achieve adaptive duty cycle and quite short listen period. Moreover, MRPM uses carrier sensing information for advanced adaptive listening which makes packets to travel multiple hops away in a single sleep/listen cycle. The simulation results verify that MRPM has features of high energy efficiency and low latency.

EMS-MAC: Energy Efficient Contention-Based Medium Access Control Protocol for Mobile Sensor Networks

Energy efficiency is a key characteristic of modern wireless sensors. Assuming that the transceiver is the most power-consuming component of a typical sensor node, then a large advantage can be achieved at the data link layer where the medium access control (MAC) protocol controls the usage of the radio unit. Many MAC protocols have been developed for traditional wireless networks. Given that the sensor network is different from the traditional wireless network in many places, researchers are looking for a MAC protocol that is specifically designed and adapted to the sensor network. Moreover, most of the contributions in the wireless sensor network have assumed static nodes. However, some applications in the area of medical care and disaster response make use of the mobile sensor network. Thus, the present paper studies and simulates the sensor MAC (S-MAC), timeout MAC and mobility-aware S-MAC (MS-MAC) protocols in terms of their energy efficiency in different mobility situations. Furthermore, an enhancement of the MS-MAC protocol, named as enhanced MS-MAC, is introduced and simulated. The results show that this enhancement can significantly improve the energy efficiency when there is a reasonable packet delivery rate.

Adaptive Duty Cycling MAC Protocols Using Closed-Loop Control for Wireless Sensor Networks

The fundamental design goal of wireless sensor MAC protocols is to minimize unnecessary power consumption of the sensor nodes, because of its stringent resource constraints and ultra-power limitation. In existing MAC protocols in wireless sensor networks (WSNs), duty cycling, in which each node periodically cycles between the active and sleep states, has been introduced to reduce unnecessary energy consumption. Existing MAC schemes, however, use a fixed duty cycling regardless of multi-hop communication and traffic fluctuations. On the other hand, there is a tradeoff between energy efficiency and delay caused by duty cycling mechanism in multi-hop communication and existing MAC approaches only tend to improve energy efficiency with sacrificing data delivery delay. In this paper, we propose two different MAC schemes (ADS-MAC and ELA-MAC) using closed-loop control in order to achieve both energy savings and minimal delay in wireless sensor networks. The two proposed MAC schemes, which are synchronous and asynchronous approaches, respectively, utilize an adaptive timer and a successive preload frame with closed-loop control for adaptive duty cycling. As a result, the analysis and the simulation results show that our schemes outperform existing schemes in terms of energy efficiency and delivery delay.

Lifetime extension for surveillance wireless sensor networks with intelligent redeployment

For wireless sensor networks (WSNs), uneven energy consumption is a major problem. A direct consequence of this is the energy hole problem, formation of sensing voids within the network field due to battery depleted sensors in the corresponding region. Hole formations are inherent in the network topology, yet it is possible to develop strategies to delay the hole formations to later stages of the network operation and essentially extend the network lifetime without sensing quality loss. In this work, we initially propose and analyze an approach that can be used to mitigate the hole problem. The approach is presented in detail and the effects on the sustained surveillance quality are presented. The results are based on simulations with different network configurations with realistic sensor models, MAC and routing protocols. By using the proposed approach, sustaining a sensing quality above a given threshold and more than doubling the network lifetime are possible. The results clearly indicate the suitability of the approach for especially demanding WSNs such as the ones used for border surveillance tasks.

Energy efficient MAC protocol for delay‐sensitive data transmission over wireless sensor network

AbstractThis paper presents an energy efficient medium access control (MAC) protocol for delay‐sensitive data transmission over wireless sensor network. In general, energy consumption and delay depend on channel monitoring interval (CMI) and data sensing period at each sensor node. Based on this fact, we propose a new preamble structure to effectively advertise CMI and avoid the overhearing problem. In order to pursue an effective tradeoff between energy consumption and delay, we also develop a CMI determining algorithm that searches for a sub‐optimal solution with a low computational complexity in a distributive way. Finally, experimental results are provided to compare the proposed MAC protocol with existing sensor MAC protocols. Copyright © 2010 John Wiley & Sons, Ltd.

Adaptive listen for energy-efficient medium access control in wireless sensor networks

Wireless Sensor Networks (WSN) have nodes that are small in size and are powered by small batteries having very limited amount of energy. In most applications of WSN, the nodes in the network remain inactive for long periods of time, and intermittently they become active on sensing any change in the environment. The data sensed by the different nodes are sent to the sink node. In contrast to other infrastructure-based wireless networks, higher throughput, lower latency and per-node fairness in WSN are imperative, but their importance is subdued when compared to energy consumption. In this work, we have regarded the amount of energy consumption in the nodes to be of primary concern, while throughput and latency in the network to be secondary. We have proposed a protocol for energy-efficient adaptive listen for medium access control in WSN. Our protocol adaptively changes the slot-time, which is the time of each slot in the contention window. This correspondingly changes the cycle-time, which is the sum of the listen-time and the sleep-time of the sensors, while keeping the duty-cycle, which is the ratio between the listen-time and the cycle-time, constant. Using simulation experiments, we evaluated the performance of the proposed protocol, compared with the popular Sensor Medium Access Control (SMAC) (Ye et al. IEEE/ACM Trans Netw 12(3):493---506, 39) protocol. The results we obtained show a prominent decrease in the energy consumption at the nodes in the proposed protocol over the existing SMAC protocol, at the cost of decreasing the throughput and increasing the latency in the network. Although such an observation is not perfectly what is ideally desired, given the very limited amount of energy with which the nodes in a WSN operate, we advocate that increasing the energy efficiency of the nodes, thereby increasing the network lifetime in WSN, is a more important concern compared to throughput and latency. Additionally, similar observations relating energy efficiency, network lifetime, throughput and latency exist in many other existing protocols, including the popular SMAC protocol (Ye et al. IEEE/ACM Trans Netw 12(3):493---506, 39).

Performance Evaluation of Sensor Medium Access Control Protocol Using Coloured Petri Nets

Formal modeling techniques can be used for analysis of wireless sensor networks (WSNs). Coloured Petri nets (CPNs) that is an extension of Petri nets is a powerful modeling technique. In this paper, we present a CPN model for modeling and performance evaluation of a medium access control protocol in WSNs named sensor-medium access control protocol (S-MAC). S-MAC is an energy-aware MAC protocol with nodes scheduling. The proposed model for this protocol uses the hierarchical modeling capability of CPNs. By using CPNs in this case study and the proposed method for modeling packet broadcast, we have demonstrated the possibility of modeling and evaluation of any other MAC protocol in WSNs or mobile ad-hoc networks (MANET).

Towards a classification of energy aware MAC protocols for wireless sensor networks

AbstractPower management is an important issue in wireless sensor networks (WSNs) because wireless sensor nodes are usually battery powered, and an efficient use of the available battery power becomes an important concern specially for those applications where the system is expected to operate for long durations. This necessity for energy efficient operation of a WSN has prompted the development of new protocols in all layers of the communication stack. Provided that, the radio transceiver is the most power consuming component of a typical sensor node, large gains can be achieved at the link layer where the medium access control (MAC) protocol controls the usage of the radio transceiver unit.MAC protocols for sensor networks differ greatly from typical wireless networks access protocols in many issues. MAC protocols for sensor networks must have built‐in power conservation, mobility management, and failure recovery strategies. Furthermore, sensor MAC protocols should make performance trade‐off between latency and throughput for a reduction in energy consumption to maximize the lifetime of the network. This is in general achieved through duty cycling the radio transceiver.Many MAC protocols with different objectives were proposed for wireless sensor networks in the literature. Most of these protocols take into account the energy efficiency as a main objective. There is much more innovative work should be done at the MAC layer to address the hard unsolved problems. In this paper, we first outline and discuss the specific requirements and design trade‐offs of a typical wireless sensor MAC protocol by describing the properties of WSN that affect the design of MAC layer protocols. Then, a typical collection of wireless sensor MAC protocols presented in the literature are surveyed, classified, and described emphasizing their advantages and disadvantages whenever possible. Finally, we present research directions and identify open issues for future medium access research. Copyright © 2009 John Wiley & Sons, Ltd.

Energy Consumption Analysis of the S-MAC Protocol with Contending Nodes under Unsaturated Conditions

We analyze the energy consumption of the sensor-medium access control (S-MAC) protocol, where contending nodes exist. Because all nodes running the S-MAC within a virtual cluster always behave with a fixed frame length, the behavior should be analyzed based on its frame. Hence, reflecting the frame architecture, we first present an analytic model for the S-MAC behavior with a discrete-time Markov chain, and then we analyze energy consumption under unsaturated conditions.

Addressing Mobility in Wireless Sensor Media Access Protocol

Handling mobility in wireless sensor networks presents several new challenges. Techniques developed for other mobile networks, such as mobile phone or mobile adhoc networks can not be applicable, as in these networks energy is not a very critical resource. This paper presents a new adaptive Mobility-aware Sensor MAC protocol (MS-MAC) for mobile sensor applications. In MS-MAC protocol, a node detects its neighbor's mobility based on a change in its received signal level from the neighbor, or a loss of connection with this neighbor after a timeout period. By propagating mobility presence information, and distance from the nearest border node, each node learns its relative distance from the nearest mobile node and from the nearest border node. Depending on the mobile node movement direction, the distances from mobile and border nodes, a node may trigger its neighbor search mechanism to quicken the connection setup time. The simulation results show that, the new mobility-aware MAC protocol can work very energy-efficiently when the network is stationary, whereas it performs much better in terms of throughput than the existing sensor MAC (SMAC) protocol in scenarios involving mobile sensors.