Behaviour Of Segmental Lining Research Articles

Effect of Segmental Joint on Internal Forces in Tunnel Lining under Seismic Loading by Numerical Method

Although segmental tunnel linings are often used for seismic areas, the influence of segment joints on the segmental lining behavior under seismic loading has not been thoroughly considered in the literature. This paper presents the results of a numerical study investigating the effects of the rotational, axial, and radial joint stiffness of the longitudinal joints on the structural forces in segmental tunnel lining under seismic loading. A 3D finite element method is adapted to establish elaborate numerical models of the segments. The validity of the numerical model was tested by comparing the results obtained with the well-known analytical methods presented by Wang and Penzien. The results demonstrate that by increasing the rotational stiffness of the segmental joint, the bending moment increases. When the rotational stiffness ratio is less than 0.5, the positive and negative bending moment variations are more. The numerical modeling results show the variations in the bending moment and the difference between the positive and negative bending moment values increased by increasing the acceleration of seismic loading. Moreover, it is significant for the values. By increasing the rotational stiffness ratio of the segmental joint, the axial force ratio decreases. By increasing the axial and shear stiffness ratio of segmental joint, the variations in the bending moment and axial force in segmental lining is not significant and is ignorable in designing segmental lining.

The Effects of Tangential Ground–Lining Interaction on Segmental Lining Behavior Using the Beam-Spring Model

The shield tunneling method is widely used, especially in urban areas, since it is efficient for minimizing disturbances to surroundings. Although segmental lining is commonly used in this method, in both the research and practice of tunnel lining design, the interaction between the ground and lining in the tangential direction remains unclear; that is, the mobilizing shear stress due to load models and the degree of the bond in the tangential direction. Therefore, to clarify the effects and mechanism of the tangential ground–lining interaction on segmental lining behavior, a parameter study was carried out, taking tangential spring stiffness, load models, soil stiffness, and shallow and deep tunnels as parameters. The interaction conditions were based on the existing literature. It was found that (1) the tangential spring has small effects on lining behavior, (2) the load model significantly affects the sectional forces, (3) the initial tangential earth pressure and slip ground–lining boundary provide more safety from a design viewpoint, and (4) in the case of shallow tunnels in soft ground, tensile stress appears in the lining. Therefore, it is important to take the tangential ground–lining interaction conditions into consideration during tunnel lining analysis.

2D numerical investigation of segmental tunnel lining under seismic loading

Segmental tunnel linings are now often used for seismic areas. However, the influence of segment joints on the segmental lining behavior under seismic loading has not been thoroughly considered in the literature. This paper presents a numerical study, which has been performed under seismic circumstance, to investigate the factors that affect segmental tunnel lining behavior. Analyses have been carried out using a two-dimensional finite difference element model. The proposed model allows studying the effect of the rotational joint stiffness, radial stiffness and the axial stiffness of the longitudinal joints. The numerical results show that a segmental lining can perform better than a continuous lining during earthquake. It has been seen that the influence of the joint distribution, the joint rotational stiffness, the joint axial stiffness, Young׳s modulus of the ground surrounding the tunnel, the lateral earth pressure factor and the maximum shear strain should not be neglected. Some important differences of the segmental tunnel lining behavior under static and seismic conditions have been highlighted.

Stress and strain state in the segmental linings during mechanized tunnelling

The application of the mechanized tunnelling has been extended in recent years. There are at present different approaches that are used in the design of segmental tunnel linings supported in mechanized tunnels. Even though segmental lining is utilized for mechanized tunnels, its behaviour is still quite unclear under in situ stress and there is a lack of data regarding the distribution of stresses inside segmental linings. So far no single effective calculation method exists for segmental lining design. The lack of clear solutions makes the use of segmental lining to be more expensive due to the adoption of greater safety factors. Therefore, a particular attention must be given in order to obtain data from monitored tunnels which permits to validate design methods. In this study, strain measurements, which were conducted during the construction of twin tunnels in the Bologna-Florence railway line, have been presented. The behaviour of segmental lining during the excavation and the influence of a new tunnel excavation on an existing tunnel have been shown through the measured data. The data are then compared with the results obtained with Einstein and Schwartz's method and Duddeck and Erdmann's method, which permits to highlight the fact that the two analytical methods underestimate structural forces induced in the segmental lining and then must be used with caution.