Secondary Grain Research Articles

One‐Stone‐For‐Three‐Birds Strategy Using a Fullerene Modifier for Efficient and Stable Inverted Perovskite Solar Cells

AbstractThe electron extraction from perovskite/C60 interface plays a crucial role in influencing the photovoltaic performance of inverted perovskite solar cells (PSCs). Here, we develop a one‐stone‐for‐three‐birds strategy via employing a novel fullerene derivative bearing triple methyl acrylate groups (denoted as C60‐TMA) as a multifunctional interfacial layer to optimize electron extraction at the perovskite/C60 interface. It is found that the C60‐TMA not only passivates surface defects of perovskite via coordination interactions between C=O groups and Pb2+ cations but also bridge electron transfer between perovskite and C60. Moreover, it effectively induces the secondary grain growth of the perovskite film through strong bonding effect, and this phenomenon has never been observed in prior art reports on fullerene related studies. The combination of the above three upgrades enables improved perovskite film quality with increased grain size and enhanced crystallinity. With these advantages, C60‐TMA treated PSC devices exhibit a much higher power conversion efficiency (PCE) of 24.89 % than the control devices (23.66 %). Besides, C60‐TMA benefits improved thermal stability of PSC devices, retaining over 90 % of its initial efficiency after aging at 85 °C for 1200 h, primarily due to the reinforced interfacial interactions and improved perovskite film quality.

One-Stone-For-Three-Birds Strategy Using a Fullerene Modifier for Efficient and Stable Inverted Perovskite Solar Cells.

The electron extraction from perovskite/C60 interface plays a crucial role in influencing the photovoltaic performance of inverted perovskite solar cells (PSCs). Here, we develop a one-stone-for-three-birds strategy via employing a novel fullerene derivative bearing triple methyl acrylate groups (denoted as C60-TMA) as a multifunctional interfacial layer to optimize electron extraction at the perovskite/C60 interface. It is found that the C60-TMA not only passivates surface defects of perovskite via coordination interactions between C=O groups and Pb2+ cations but also bridge electron transfer between perovskite and C60. Moreover, it effectively induces the secondary grain growth of the perovskite film through strong bonding effect, and this phenomenon has never been observed in prior art reports on fullerene related studies. The combination of the above three upgrades enables improved perovskite film quality with increased grain size and enhanced crystallinity. With these advantages, C60-TMA treated PSC devices exhibit a much higher power conversion efficiency (PCE) of 24.89 % than the control devices (23.66 %). Besides, C60-TMA benefits improved thermal stability of PSC devices, retaining over 90 % of its initial efficiency after aging at 85 °C for 1200 h, primarily due to the reinforced interfacial interactions and improved perovskite film quality.

Impacts of T6 heat treatment on the microstructural, mechanical, and corrosion properties of thixoformed AA7075 alloy produced by cooling slope casting

Abstract Research into semi-solid metal forming techniques has been ongoing for an extended period with the aim of producing near-net shape products from aluminum alloys. The primary focus has traditionally been on casting alloys seeking to offer an alternative to the other processes such as high pressure die casting. Over the past twenty years, wrought aluminum alloys have also been explored for thixoforming operations as an alternative to traditional plastic deformation techniques. This research investigated the impacts of T6 heat treatment on the microstructural, mechanical, and corrosion properties of AA7075 alloy samples produced through cooling slope casting and subsequent thixoforming with different reheating durations. The selected alloy was chosen due to its widespread use in various industries, attributed to its excellent strength-to-density ratio achieved after T6 heat treatment. Building on optimized cooling slope casting parameters from a prior study, the standard solution treatment procedure following thixoforming with extended reheating times was found to be inadequate. Hardness and tensile tests revealed that specimens reheated for 120 min exhibited significantly reduced response to T6 treatment. Despite achieving the targeted hardness value of 154 HB with samples reheated for 20 min prior to thixoforming and T6 heat treatment, especially the elongation at break values were unsatisfactory. Potentiodynamic polarization tests indicated that corrosion primarily involved grain dissolution, with longer reheating times decreasing corrosion resistance due to increased amount of secondary phases and grain isolation. These findings highlight that while AA7075 alloy can be processed into semi-solid formable materials via cooling slope casting, issues such as hot tearing, micro-shrinkage, and physical defects post-thixoforming hinder the achievement of desired tensile properties.

Cooling rate effects on microstructure and diffusion behaviour in Ti65 alloy: Insights from a modified diffusion model

In the continuous cooling process, the growth of the equiaxed α-phase grains in near-α high-temperature titanium alloys is controlled by the diffusion of alloying elements. Establishing a specific connection between the cooling rate and the diffusion behaviour of alloying elements aids in the precise prediction of the evolution of equiaxed α-phase grain size. This study meticulously controlled the cooling rate during the two-phase region annealing treatment of the Ti65 alloy. Using EPMA technology, the diffusion behaviour of solute elements during cooling was accurately characterized. The study found that slowing the cooling rate promotes the coarsening of the lamellar secondary α-phase grains and the growth of the primary equiaxed α-phase grains. At higher annealing temperatures, the growth of equiaxed α-phase grains can occur at faster cooling rates, while coarse lamellar secondary α-phase grains can be retained at slower cooling rates. The diffusion behaviour of solute elements Al, Ta, Mo, and W between the α-phase and transformed β-phase matrix is significantly influenced by the cooling rate, thus they are considered as the controlling elements for the growth of the equiaxed α-phase grains. Based on the diffusion behaviours of these controlling elements, their single-element diffusion models were categorized and integrated for predicting the grain size of the equiaxed α-phase. The predictions from the revised diffusion model show an excellent agreement with the actual results, with an error margin of about 5%.

Foliar application of melatonin improve the number of secondary branches and secondary branch grains quality of rice.

Melatonin plays an important role in plant growth and development. However, little information is available about melatonin regulating rice panicle structure and yield. This study explored the regulatory effects and mechanisms of melatonin spraying before the panicle differentiation stage on rice panicle structure and grain quality. The results showed that spraying melatonin before panicle differentiation increased rice yield, which was mainly reflected in the increase in spikelets per panicle and the percentage of filled grains. In addition, melatonin treatment significantly increased the panicle length. The results of panicle structure analysis showed that the increase in spikelets per panicle caused by melatonin was attributed to the significant increase in the number of secondary branches, total number of secondary branch spikelets, and number of spikelets per secondary branch. The results showed that melatonin can increase the content of zeatin, auxin, and gibberellin, and reduce the content of abscisic acid. These results showed that melatonin affected panicle structure by regulating hormone content, thereby improving yield. In addition, melatonin improves the processing quality, appearance quality, and nutritional quality of secondary branch grains. The above results indicate that application of melatonin improves the number of secondary branches and the quality of grainss on secondary branches.

Inhibition of interfacial cracks in 304L-Inconel718 bimetal fabricated via laser powder bed fusion

Multi-material additive manufacturing is crucial for intricate component fabrication, yet challenges, such as interfacial cracks and weak bonding, persist. This work investigated the laser powder bed fusion (L-PBF) of bimetallic components (stainless steel 304L-nickel-based alloy Inconel718) crucial in aerospace and nuclear applications. It is found that the interfacial cracks predominantly occur within the compositional transition zone where the proportion of 304L is between 45wt.% and 75wt.%, characterized by brittle Laves phases along grain boundaries. Experimental and finite element simulations of melt pool reveal that a higher ratio of temperature gradient (G̅) to the grain growth rate (R̅) (G̅/R̅) results in straight grain boundaries with underdeveloped secondary dendrites. This leads to the formation of continuous liquid film and strip-like Laves phase at grain boundaries, causing interfacial cracks during L-PBF. To suppress these cracks, this work proposes manipulating grain boundaries into a tortuous morphology through promoting the growth of secondary dendrites. By controlling the G̅/R̅ ratios below the critical value (<147.9×106K∙s/m2) and combining with a high cooling rate (G̅×R̅) during L-PBF, a well-developed secondary dendritic structure and grain refinement are achieved, significantly enhancing grain boundary tortuosity and forming discretely distributed Laves phases. As a result, interfacial cracks are completely suppressed, enabling the successful manufacturing of crack-free 304L-Inconel718 bimetallic components. The approach of tailoring the distribution of brittle precipitates through manipulating grain boundary morphology proposed in this work provides a novel and practical pathway for inhibiting cracks in multi-material additive manufacturing.

Solution-Induced surface modification and secondary grains growth for high-performance and stable perovskite solar cells

Enhancing the quality of perovskite layer and refining the interface between the perovskite layer and the hole transport layer (HTL) represent pivotal strategies for optimizing the efficiency and stability of perovskite solar cells (PSCs). We accomplished this by employing a solution isopropanol (IPA), capable of selectively dissolving residual unreacted methylammonium and formamidine salts on the perovskite surface while preserving the integrity of lead iodide. Through control of the immersion time, we facilitated secondary crystal growth on the top of perovskite film. The resultant treated film exhibited a markedly suitable bandgap position and a diminished presence of residual trips. The IPA-treated sample led to a noteworthy photovoltaic conversion efficiency (PCE) of 23.34 %, compared to 21.46 % efficiency for untreated control sample. Furthermore, under sustained illumination at AM 1.5G with 25 % relative humidity, the uncovered IPA-treated sample retained an impressive 92 % of their initial efficiency after 1000 h. Further scrutiny revealed that this solution-based treatment effectively passivated trips, enhanced perovskite film quality, established novel built-in electric fields, and mitigated charge carrier recombination. This work provides a simple perovskite film treatment approach that does not require complex molecular engineering and can be applied not only to PSCs but also to other perovskite optoelectronic devices.

Development of V2O3 Nanostructures for Alkali Metal Ion Batteries: A Novel Approach through Mild Metal Vapor Reduction and Interface Engineering.

V2O3 has been extensively researched as a battery electrode material due to its ample reserves and high theoretical capacity. However, the synthesis of valence-sensitive V2O3 presents technical challenges as it requires a strict combination of high-temperature treatment and a narrow range of oxygen partial pressures. This study proposes a gentle Li vapor-assisted thermal reduction method to synthesize pure-phase V2O3 at a relatively low temperature of 480 °C without any hazardous gases. It has been discovered that reducing the temperature also improves the specific surface area of the nanoto-mesoscale hierarchical structures and enhances the reactive sites between their secondary grains. These advantages enable the V2O3 micronano particles to store higher levels of Li+, Na+, and K+, increase ionic transport, and tolerate volume expansion. It demonstrates a significant capacity of 767 mA h g-1 in lithium-ion batteries, 393 mA h g-1 in sodium-ion batteries, and 209 mA h g-1 in potassium-ion batteries. It has also been discovered that the crystal structure of V2O3 is easily adjustable by varying the synthesis temperature, which significantly affects the electrochemical storage mechanism. The V2O3 synthesized at 480 °C with low crystallinity exhibits a notable intercalation reaction, facilitating the electrochemical kinetics of reversible insertion/extraction of Li+, Na+, and K+. In contrast, the highly crystalline sample synthesized at 580 °C displays pseudocapacitance behavior instead of an intercalation reaction. The highly crystalline sample synthesized at 680 °C exhibits a thorough pseudocapacitance reaction possessing the capacitive functionality for the electrochemical storage of Na+ or K+ with larger ion radii. This study describes a new synthesis strategy and rational modification of vanadium-based electrodes for alkali metal ion batteries, leading to the development of reasonably priced rechargeable battery systems with applications extending beyond lithium-ion batteries.

Effect of cladding speed on the microstructure and hardness of high-hardness B-bearing Cr17Ni2 coating

The B-bearing iron-based coating produced by laser cladding exhibits super-high hardness. However, the strengthening mechanism of B-bearing Cr17Ni2 coating and non-equilibrium phase transformation during the cooling stage require further investigation. The study focused on the B-bearing Cr17Ni2 coatings produced by laser cladding at four speeds ranging from 10 mm/s to 200 mm/s. The results show that the thickness of the single layer in the coatings gradually decrease as the increase of scanning speed. The secondary dendrite arms spacing and grain size also decrease with increasing scanning speed. The microstructure of the coating consists of a martensitic phase and a eutectic phase consisting of Cr2B compounds and austenite. Combined with G\\R diagram and finite element analysis, the microstructure refining mechanism of the coating has been concluded. The effect of fine grain strengthening, solid solution strengthening, precipitation strengthening, and dislocation strengthening on hardness is investigated. It has been observed that the coating hardness increases with increasing scanning speed. This change in the hardness of the coatings is mainly because of the grain and precipitate refining.

Biodegradable PMMA coated Zn–Mg alloy with bimodal grain structure for orthopedic applications - A promising alternative

The study examines the impact of microstructure and polymethyl methacrylate (PMMA) grafting on the degradability of Zn–Mg alloys. The mechanical properties of a Zn alloy containing 0.68 wt% Mg and extruded at 200 °C are enhanced for degradable load-bearing applications, addressing a crucial need in the field. The material exhibits a bimodal grain size distribution that is random texture, consisting of secondary phases, grains, and sub-grains. With an elongation to failure of 16 %, the yield and ultimate tensile strengths are 325.9 and 414.5 MPa, respectively, and the compressive yield strength is 450.5 MPa.The “grafting-from” method was used to coat a few micrometers thick of PMMA on both bulk and scaffold Zn alloys to mitigate the corrosion rate. The last one is a porous structure, with a porosity of 65.8 %, considered as in the first approach of an orthopedic implant. After being immersed for 720 h, the PMMA-grafted bulk alloy's corrosion rate decreased from 0.43 to 0.25 mm/y. Similarly, the scaffold alloy's corrosion rate reduced from 1.24 to 0.49 mm/y. These results indicate that the method employed could be used for future orthopedic applications.

Thermo-mechanical fatigue crack growth in a nickel-based powder metallurgy superalloy

Fatigue crack growth is studied in a nickel-based powder metallurgy (PM) superalloy (FGH4099) subjected to in-phase (IP) and out-of-phase (OP) thermo-mechanical fatigue (TMF), as well as isothermal fatigue (IF) at peak temperature. The crack growth rate and path are evaluated for both coarse grain (CG) and fine grain (FG) FGH4099, especially the effects of phase angle and polycrystalline microstructure. The results show that the TMF crack propagation is mainly transgranular in OP condition; while in IP condition, fatigue crack propagates intergranularly at low ΔK and transforms to transgranular after passing the transition region. The crack propagation resistance for FG microstructure is lower than that for CG microstructure at elevated temperature, as a result of secondary cracks and grain boundary weakening effect. Crystallographic slip controls the crack propagation process, while the twin boundaries (TB) and special grain boundaries also exert a significant influence on crack deflection. The formation of secondary cracks is closely related to local misorientation and crystallographic deformation during TMF crack propagation. The crack deflection in a single grain reveals a competition mechanism between crystallographic slip and grain boundary effect, which explains the lower crack growth rate for OP when compared to IP or IF.

Implementing multi-trait genomic selection to improve grain milling quality in oats (Avena sativa L.).

Oats (Avena sativa L.) provide unique nutritional benefits and contribute to sustainable agricultural systems. Breeding high-value oat varieties that meet milling industry standards is crucial for satisfying the demand for oat-based food products. Test weight, thins, and groat percentage are primary traits that define oat milling quality and the final price of food-grade oats. Conventional selection for milling quality is costly and burdensome. Multi-trait genomic selection (MTGS) combines information from genome-wide markers and secondary traits genetically correlated with primary traits to predict breeding values of primary traits on candidate breeding lines. MTGS can improve prediction accuracy and significantly accelerate the rate of genetic gain. In this study, we evaluated different MTGS models that used morphometric grain traits to improve prediction accuracy for primary grain quality traits within the constraints of a breeding program. We evaluated 558 breeding lines from the University of Illinois Oat Breeding Program across 2 years for primary milling traits, test weight, thins, and groat percentage, and secondary grain morphometric traits derived from kernel and groat images. Kernel morphometric traits were genetically correlated with test weight and thins percentage but were uncorrelated with groat percentage. For test weight and thins percentage, the MTGS model that included the kernel morphometric traits in both training and candidate sets outperformed single-trait models by 52% and 59%, respectively. In contrast, MTGS models for groat percentage were not significantly better than the single-trait model. We found that incorporating kernel morphometric traits can improve the genomic selection for test weight and thins percentage.

CgSSR marker based trait associations for Sitotroga cerealella (Olivier) resistance in stored paddy rice

Rice is stored for a longer time and many primary and secondary insect pests attack grains, causing both quantitative and qualitative losses. Physicochemical characteristics of grain influence stored grain insect susceptibility and resistance. Identification of gene/Quantitative Trait Loci (QTLs) and introgression in the cultivars would provide the desired solution for varietal resistance against S. cerealella. A group of 80 rice varieties was used for genetic analysis for the identification of candidate genes responsible for Sitotroga cerealella resistance. Heat maps derived from values in the kinship matrix were used to group the varieties into three subpopulations. The largest subpopulation has 34 varieties, while the lowest had 19. The first three principal components (PCs) explained 16, 9, and 6 percent of total variation, respectively, as indicated by the Principal Component Analysis (PCA). The PCA results complemented the heat map results in defining population structure. Genome-wide association mapping can detect marker-trait associations/QTLs in a heterogeneous population of breeding lines, despite population structure and unequal family relatedness. As shown by the Genomic Association and Prediction Integrated Tool (GAPIT) heat map, there are three subpopulations in the association mapping panel. Two cgSSR markers, related to gene SDG725 and FLO2, were linked to the attributes and responsible for conferring resistance against S. cerealella infestation. This is the first report of association and that would help in the development of cultivar with S. cerealella resistance.

Study on the heat treatment of multispectral ZnS for residual stress reduction

Multispectral ZnS (M − ZnS) will inevitably introduce stresses during the chemical vapor deposition (CVD) polycrystalline growth and hot isostatic pressing (HIPping) stages. In this paper, the generation mechanism and elimination method of residual stresses in M − ZnS are analyzed by means of SEM, transmittance, XRD analysis and mechanical property characterization, and the effects of heat treatment temperature, time and material annealing structure on the apparent morphology, optical and mechanical properties of M − ZnS materials are investigated. The results show that the internal stresses of M − ZnS mainly originate from the CVD ZnS growth and HIPping stages, and the most effective method to reduce the stresses is heat treatment. The key factors affecting the effect of heat treatment include temperature, time, and annealing structure. Selecting a GZ(G) annealing structure combined with a suitable cooling rate for heat treatment of M − ZnS materials will significantly improve the heat treatment effect. More annealing time has a significant effect on the transmittance in the 0.38–3 μm band, and insignificant effect on the transmittance in the 3–5 μm and 8–10 μm bands. Heat treatment will bring some degree of structural changes to the material, often manifested including a trace of hexagonal phase structure, which will affect the optical imaging quality of the window material. Heat treatment contributes to secondary grain growth, with an increase in grain size and a decrease in grain boundaries. Excessive heat treatment accelerates the loss of hardness and bending strength, and also leads to the generation of micro-cracks and macro-cracks in the material, reducing the mechanical properties of the material. Heat treatment holding 200 h and 100 h compared to the unannealed, Vickers hardness decreased by 13.518 and 7.96, respectively, bending strength decreased by 4.77 MPa and 1.73 MPa, respectively. Therefore, in actual production, should not be selected excessive heat treatment time.

Mg/Al Double-Pillared LiNiO2 as a Co-Free Ternary Cathode Material Ensuring Stable Cycling at 4.6 V.

Cobalt-free (Co-free) and nickel-rich (Ni-rich) cathode materials have attracted significant attention and undergone extensive studies due to their affordability and superior energy density. However, the commercialization of these Co-free materials is hindered by challenges such as cation disorder, irreversible phase changes, and inadequate high-voltage performance. To overcome these challenges, a Co-free ternary cathode material of Mg/Al double-pillared LiNiO2 (NMA) synthesized via a wet-coating and lithiation-sintering technique is proposed. Fundamental studies reveal that Mg and Al have the potential to form a distinctive double-pillar structure within the layered cathode, enhancing its structural stability. To be specific, the strategic placement of Mg and Al in Li and Ni layers, respectively, effectively reduces Li+/Ni2+ disorder and prevents irreversible phase transitions. Additionally, the inclusion of Mg and Al refines the primary grains and compacts the secondary grains in the cathode material, reducing stress from cyclic usage and preventing material cracking, thereby mitigating electrolyte erosion. As a result, NMA demonstrates exceptional electrochemical performance under a high charge cutoff voltage of 4.6 V. It maintains 70% of initial specific capacity after 500 cycles at 1 C and exhibits excellent rate performance, with a capacity of 162 mAh g-1 at 5 C and 149 mAh g-1 at 10 C. As a whole, the produced NMA achieves a high structural stability in cases of excessive delithiation, providing a groundbreaking solution for the development of cost-effective and high-energy-density cathode materials for lithium-ion batteries.

Magnetization reversal and coercivity mechanism in ferrimagnetic M-type hexaferrite by controlling phase evolution

The correlation of phase evolution (annealing at different temperatures) with magnetic properties like magnetization reversal, coercivity mechanism, and energy product in M-type hexaferrite by substituting Sr in place of Ba has been reported in the present article. The Ba1-xSrxFe12O19 (x = 0.0, 0.5, & 1.0) have been prepared by the sol–gel auto-combustion method followed by annealing at different temperatures from 800 °C to 1200 °C. The structural and magnetic properties have been characterized by X-ray diffraction, Field emission scanning electron microscopy, Raman spectroscopy, and Vibrating sample magnetometer. The Rietveld refinement confirms contraction in unit cell parameters by replacing Sr in place of Ba and lattice expansion with increasing annealing temperature. There is no significant effect of substitution on magnetic properties found rather heat treatment affects greatly. The transition from a single domain to multidomain particles and their contribution to initial magnetization curves are analyzed. The differential susceptibility (dM/dH) calculated from room temperature magnetization confirms the existence of a pinning effect during magnetization reversal for samples heat treated below 1200 °C. Secondary phases or grain boundaries are believed to act like pinning centers. This work opens insight into the domain wall motion by microstructure engineering. The coercivity is tuned to 6.09 kOe by controlling the annealing temperature for the Ba1-xSrxFe12O19 (x = 1.0) sample. The maximum energy product (BH)max in the range of 0.94–1.27 MGOe has been achieved.

Maize green leaf area index dynamics: genetic basis of a new secondary trait for grain yield in optimal and drought conditions

Key messageGreen Leaf Area Index dynamics is a promising secondary trait for grain yield and drought tolerance. Multivariate GWAS is particularly well suited to identify the genetic determinants of the green leaf area index dynamics.Improvement of maize grain yield is impeded by important genotype-environment interactions, especially under drought conditions. The use of secondary traits, that are correlated with yield, more heritable and less prone to genotype-environment interactions, can increase breeding efficiency. Here, we studied the genetic basis of a new secondary trait: the green leaf area index (GLAI) dynamics over the maize life cycle. For this, we used an unmanned aerial vehicle to characterize the GLAI dynamics of a diverse panel in well-watered and water-deficient trials in two years. From the dynamics, we derived 24 traits (slopes, durations, areas under the curve), and showed that six of them were heritable traits representative of the panel diversity. To identify the genetic determinants of GLAI, we compared two genome-wide association approaches: a univariate (single-trait) method and a multivariate (multi-trait) method combining GLAI traits, grain yield, and precocity. The explicit modeling of correlation structure between secondary traits and grain yield in the multivariate mixed model led to 2.5 times more associations detected. A total of 475 quantitative trait loci (QTLs) were detected. The genetic architecture of GLAI traits appears less complex than that of yield with stronger-effect QTLs that are more stable between environments. We also showed that a subset of GLAI QTLs explains nearly one fifth of yield variability across a larger environmental network of 11 water-deficient trials. GLAI dynamics is a promising grain yield secondary trait in optimal and drought conditions, and the detected QTLs could help to increase breeding efficiency through a marker-assisted approach.

Crystallization and defects regulation of efficient perovskite solar cells via surface induced secondary grain growth with formamidine iodine treatment

Trap–mediated non–radiative loss is a major efficiency and stability obstale for solution–processed perovskite solar cells (PSCs). To address this issue, defect passivation using organic molecules has been identified as an effective strategy due to the ionic nature of the perovskite lattice. Herein, Ostwald ripening by using formamidine iodine (FAI) is reported to inhibit the carrier trap induced recombination via promoting secondary grain growth at perovskite surface. Based on secondary grain growth with FAI treatment, the graded passivation was presented caused by FA+ and I- from FAI. Moreover, the findings from time resolved photoluminescence and space charge–limited current technology indicate enhancements in the crystal quality. Consequently, this approach yielded a remarkable power conversion efficiency (PCE) of 20.62% for the FAI modified MAPbI3 photovoltaics, with significantly improved open–circuit voltage ratio of 3.10%, short–circuit density ratio of 6.11%, fill factor ratio of 9.46% and PCE ratio of 19.06%. Moreover, the device show the excellent stability. This study introduces simple and reproducible procedures for fabricating PSCs, which can be readily extended to diverse optoelectronic device applications.

Effect of Gradient Heat Conduction on Secondary Recrystallization of Grain-Oriented Silicon Steel

The grain-oriented silicon steels were subjected to gradient heat conduction during high-temperature annealing by using thermal insulation cotton. The macrostructures of samples subjected to circumferential gradient heat conduction showed a “petal-like” morphology with peripheral columnar grains and central equiaxed grains, while samples subjected to transverse gradient heat conduction showed a morphology with approximately 50% columnar grains and 50% equiaxed grains. The grain orientations, magnetic domains as well as magnetic properties in different regions were detected. Results showed that the magnetic induction intensity of cylindrical grains was better than that of equiaxed grains while the iron loss was worse, which indicated that a fast heating rate during high-temperature annealing was conducive to the accuracy of Goss grains. The magnetic domains in columnar grains were wider than the equiaxed grains, which resulted in poorer iron loss. A theory of the competitive growth among secondary Goss grains was proposed. Under the condition of gradient heat conduction, once the Goss grains with the fastest heat conduction grew up abnormally, they would compete with other Goss grains which were supposed to survive in traditional processes and swallow up them until adjacent to the secondary equiaxed grains which were later developed.

Surface passivation for efficient and stable perovskite solar cells in ambient air: The structural effect of amine molecules

Amine-based molecules are frequently utilized for defect passivation in perovskite films. However, the passivation effect can vary considerably depending on the structural differences of the amine molecules. In this study, we selected small-sized formamidine iodide (FAI), long-chain octylammonium iodide (OAI), and aromatic nicotinic acid (NA) to passivate surface defects in perovskite films. The charge transport in perovskite solar cells (PSCs) was inhibited by the excessively long alkyl chain of OAI but was enhanced by the π-conjugated structure of NA. Consequently, the power conversion efficiency (PCE) of OAI and NA-passivated PSCs decreased by 0.91% and increased by 0.23%, respectively. Interestingly, FAI was found to react preferentially with the PbI2 at the grain boundary of perovskite films, promoting secondary grain growth and resulting in a 21% increase in grain size. Due to the reduction in grain boundaries and the combined passivation of MA+ and I− vacancies, the PCE of FAI-passivated PSCs increased from 18.63% to 19.35% in ambient air and maintained 91% of their initial values after 76 days of storage under conditions of 20 ± 5 °C and <5% RH. This study introduces a promising strategy for selecting an appropriate amine molecule for surface passivation in efficient and stable fully-ambient air processed PSCs.