Rechargeable Research Articles

Sustainable and efficient recovery of lithium from rubidium raffinate via solvent extraction

In recent years, with the increasing prevalence of rechargeable lithium-ion batteries in the burgeoning markets of electric vehicles and portable electronic devices, the consumption of lithium batteries has significantly surged. Hence, the efficient development and utilization of associated lithium resources bear paramount significance. This study aims to recover lithium from rubidium raffinate via solvent extraction. A systematic investigation was conducted to examine the effects of various parameters such as organic phase concentration, contact time, and phase ratio (O/A) during the separation process. The results indicated that the organic phase composed of 0.1 mol/L 4,4,4-Trifluoro-1-phenyl-1,3-butanedione (HBTA) and 0.1 mol/L Trioctylphosphine oxide (TOPO) could efficiently extract lithium from the rubidium raffinate. The optimal conditions were observed at a temperature of 20℃, O/A=1, and a contact time of 5 min. After three-stage countercurrent extraction, a lithium extraction rate of 99.24 % could be achieved, with over 95 % of the sodium easily scrubbed by 0.1 mol/L HCl at an O/A=10. With the use of 3 mol/L HCl, stripping efficiency exceeding 99 % could be attained at an O/A=10, consequently a successful preparation of battery-grade lithium carbonate product was achieved. Regeneration experiments confirmed the organic phase's excellent reproducibility efficiency. Slope analysis and density function theory (DFT) simulations indicated that optimal lithium extraction is achieved when HBTA and TOPO are at equal molar concentrations. The proposed process is expected to provide a green and sustainable route for the recovery of associated lithium resources.

Cu single atoms regulating nitrogen active-sites of g-C3N4 for sodium ion storage

Nitrogen-rich material of graphitic carbon nitride (g-C3N4) with cost-effectiveness and easy accessibility has been considered as one of the most promising anode materials for sodium ion batteries (SIBs). However, the excessive presence of non-stable nitrogen sites in low crystallinity carbon nitrides would result in significant irreversibility, inadequate ion conductivity and structural instability, thereby limiting its practical application. Herein, a novel low-temperature strategy is proposed to stabilize the g-C3N4 by modulating the nitrogen configuration with single-atoms copper. The formed copper single atoms serving as anchors effectively regulate the coordination environment of nitrogen atoms in carbon nitride, thereby constructing stable nitrogen active sites for Na+ storage and conductive networks for rapid Na+ transport. Therefore, the Cu1.0/NC exhibits superior capacity (350.4 mAh g−1 at 50 mA g−1), exceptional rate performance (252.3 mAh g−1 at 1000 mA g−1), and long-cycle stability (capacity retention rate of 80.3 % after 1000 cycles at 5A g−1). Furthermore, in-situ Raman, ex-situ XANES and XPS technologies jointly reveal that the Cu atoms significantly influence the charge transfer process of Na+ and change the storage mode of sodium through redox effects during the sodiation/desodiation process. This work proves that single-atom engineering is a novel and feasible strategy to optimize the high-performance electrode materials for rechargeable batteries.

Carbon nanotubes as efficient anode current collectors for stationary aqueous Zn–Br2 batteries

Static Zn–Br2 batteries are considered an attractive option for cost-effective and high-capacity systems for large energy storage. Yet, the corrosive nature of the Zn–Br2 electrolytes entails a careful selection of all cells' ingredients to avoid rapid degradation of the batteries upon cycling. Thanks to their high chemical resistance and excellent conductivity, carbonaceous electrodes are typically utilized as current collectors for the cathode side, while thin Zn or Ti foils are most widely used as the anodes' current collectors. However, these metals tend to corrode fast, thus undermining the desirable performance of the cells as durable and stable rechargeable batteries. We demonstrate the effective utilization of carbon nanotubes (CNT) films as highly stable anode current collector for Zn–Br2 batteries. Dispersion of the CNT beforehand in slurries containing anionic, cationic, or neutral surfactants yielded distinct chemical and physical characteristics of these carbonaceous electrodes. This, in turn, led to significant differences in the morphology of the deposited Zn, consequently affecting the electrochemical performance of the Zn anodes. These findings provide insight into the interactions between Zn cations and the surface of CNTs, offering opportunities for further surface modifications of CNTs as effective anodes’ substrates for Zn–Br2 batteries.

Selenium-induced anion vacancy and active site migration stimulating remarkable sulfide Na-Ion storage

Heterojunctions and controllable anionic vacancies are perceived to be powerful means of ameliorating the performance of sodium-ion batteries assignable to their unique physical and chemical properties. However, the mechanism by which heterojunction and vacancy structures affect sodium-ion battery storage remains to be systemically explored. In this study, the Se doped CoS2@CoS1.035@Carbon (Se-CoS2@CoS1.035@C) heterostructure with anion vacancy was synthesized by a one-step calcination. These heterostructures with lower metal oxidation states and anionic vacancies exhibit exceptional Na+ storage performance (554.3 mA h g−1 after 1500 cycles at 5.0 A g−1). Both electrochemical tests and theoretical calculations demonstrate excellent pseudocapacitive behavior and enhanced Na+ adsorption during discharge because of anionic vacancies and Se doping. Additionally, introducing weaker Co-Se bonds and extending Co-S and Co-Se bonds reduce binding energies, which effectively accelerates the conversion reaction. Our findings provide a feasible way to rationally design and facilely prepare heterostructured anode materials with rich anionic vacancies for sodium-ion batteries.

ClBES1/BZR1-1, a brassinosteroid-responsive transcription factor, negatively regulates lignin deposition during secondary xylem formation in Cunninghamia lanceolata

Cunninghamia lanceolata (Chinese fir) is an important industrial coniferous timber tree in southern China with high yield and excellent wood traits. Brassinosteroids (BRs), a class of polyhydroxylated steroidal hormones, play critical roles in the formation of wood, which is the most abundant biomass produced by plants. However, the molecular regulatory network of BR-mediated wood formation remains largely uncharacterized in coniferous trees, especially in Chinese fir. To this end, systematic identification and characterization of the BES1/BZR1 transcription factor (TF), the specific BR-responsive TF, were performed. Seven ClBES1/BZR1 members were screened and distributed on four chromosomes. ClBES1/BZR1s showed various expression profiles in different tissues and growth stages. ClBES1/BZR1-1, a hub gene in BR-mediated xylem development, repressed the transcription activity of ClCCoAOMT and ClMYB3 by directly binding to their promotors. Furthermore, ClBES1/BZR1-1 overexpression significantly decreased the lignin biosynthesis and xylem differentiation compared to wild-type. In contrast, ClBES1/BZR1-1 dominant repression greatly promoted lignin deposition during secondary cell wall (SCW) development. Consequently, by repressing the lignin-related genes’ expression, ClBES1/BZR1-1 negatively regulated the SCW deposition and xylem development in Chinese fir. These findings shed light on the regulatory role of BR modulating lignin accumulation during wood formation.

Multi-objective sizing and dispatch for building thermal and battery storage towards economic and environmental synergy

The role of building thermal and battery storage is pivotal in advancing smart cities and achieving sustainability goals through effective energy management. Despite their significance, there are several limitations in the sizing approach and value stream analysis with various objectives for their widespread adoption in buildings. This work proposes a flexible and scalable multi-objective optimization framework for optimal sizing and dispatch of building thermal and battery storage, addressing multiple objectives simultaneously using mixed-integer linear programming. The weighted-sum method is adapted, combining multiple objectives into a single function. The two-stage procedure iterates over different weights, generates optimal solutions, and forms the Pareto front. Case studies are performed to assess the energy, economic, and environmental benefits of building energy storage systems for a large office building in three climate locations. The results demonstrate that the proposed framework efficiently determines optimal sizing and dispatch strategies, addressing the balance between economic viability and emission reduction. The dynamic relationship between time-of-use energy charges and emission factors leads to diverse strategies based on whether economic or environmental concerns are prioritized. This research enhances our understanding of the benefits of thermal and battery storage systems in buildings, providing valuable guidance to stakeholders.

Performance enhancement of rechargeable zinc-air battery through synergistic ex-solution of multi-component Pt/CoWO4-x catalysts

Advancing zinc-air battery (ZAB) technology necessitates the development of air cathode electrocatalyst systems that demonstrate high reactivity and stability. We introduce a novel method to fabricate a robust catalyst-support hybrid. This hybrid comprises Co-doped Pt nanoparticles (NPs) anchored on metal oxide (Ex-PtCoWO) nanofibers (NFs), synthesized via electrospinning followed by selective metal ex-solution. Controlling the ex-solution of metal NPs leads to a highly active and stable oxygen reduction reaction (ORR). Moreover, the three-dimensional CoWO4-x NFs network enhances the surface exposure of ex-solved metal NPs, thereby aiding both selective ex-solution and the provision of active sites for the oxygen evolution reaction (OER) during ZAB recharge. The Ex-PtCoWO NF exhibits an ORR half-wave potential of 0.89 V and an OER potential of 1.69 V at 10 mA cm−2 in alkaline media. ZABs utilizing Ex-PtCoWO NF show an extended cycle life of over 240 h with reduced charge-discharge polarization, compared to commercial catalysts.

Performance enhancement of rechargeable zinc-air battery through synergistic ex-solution of multi-component Pt/CoWO4-x catalysts

Advancing zinc-air battery (ZAB) technology necessitates the development of air cathode electrocatalyst systems that demonstrate high reactivity and stability. We introduce a novel method to fabricate a robust catalyst-support hybrid. This hybrid comprises Co-doped Pt nanoparticles (NPs) anchored on metal oxide (Ex-PtCoWO) nanofibers (NFs), synthesized via electrospinning followed by selective metal ex-solution. Controlling the ex-solution of metal NPs leads to a highly active and stable oxygen reduction reaction (ORR). Moreover, the three-dimensional CoWO4-x NFs network enhances the surface exposure of ex-solved metal NPs, thereby aiding both selective ex-solution and the provision of active sites for the oxygen evolution reaction (OER) during ZAB recharge. The Ex-PtCoWO NF exhibits an ORR half-wave potential of 0.89 V and an OER potential of 1.69 V at 10 mA cm−2 in alkaline media. ZABs utilizing Ex-PtCoWO NF show an extended cycle life of over 240 h with reduced charge-discharge polarization, compared to commercial catalysts.

Islanded micro-grid under variable load conditions for local distribution network using artificial neural network

ABSTRACT This research proposes an intelligent artificial neural network (ANN) controller designed for a micro-grid featuring solar photovoltaic, wind, and Battery Energy Storage (BES) systems, integrated with a shunt voltage source converter. The primary goal of this proposed method is to minimize Total Harmonic Distortion (THD) and ensure a stable Distribution Line Commutation Voltage (DLCV) amidst load variations, achieving a rapid settling period. The STF not only facilitates phase synchronization but also effectively separates harmonic and fundamental components. This research contributes to advancing micro-grid control strategies, particularly in enhancing stability and reducing distortion during variable operating conditions. Based on an analysis of the four test cases, it is evident that the proposed strategy lowered the THDs to 4.63%, 3.45%, 3.05%, and 4.70% for each test case, as well as the PF to a level that was similar. The proposed controller shows better results compared with other controllers like Sliding Mode Controller (SMC) and the Proportional-Integral Controller (PIC).

Islanded micro-grid under variable load conditions for local distribution network using artificial neural network

ABSTRACT This research proposes an intelligent artificial neural network (ANN) controller designed for a micro-grid featuring solar photovoltaic, wind, and Battery Energy Storage (BES) systems, integrated with a shunt voltage source converter. The primary goal of this proposed method is to minimize Total Harmonic Distortion (THD) and ensure a stable Distribution Line Commutation Voltage (DLCV) amidst load variations, achieving a rapid settling period. The STF not only facilitates phase synchronization but also effectively separates harmonic and fundamental components. This research contributes to advancing micro-grid control strategies, particularly in enhancing stability and reducing distortion during variable operating conditions. Based on an analysis of the four test cases, it is evident that the proposed strategy lowered the THDs to 4.63%, 3.45%, 3.05%, and 4.70% for each test case, as well as the PF to a level that was similar. The proposed controller shows better results compared with other controllers like Sliding Mode Controller (SMC) and the Proportional-Integral Controller (PIC).

Neonatal microbiota colonization drives maturation of primary and secondary goblet cell mediated protection in the pre-weaning colon.

In the distal colon, mucus secreting goblet cells primarily confer protection from luminal microorganisms via generation of a sterile inner mucus layer barrier structure. Bacteria-sensing sentinel goblet cells provide a secondary defensive mechanism that orchestrates mucus secretion in response to microbes that breach the mucus barrier. Previous reports have identified mucus barrier deficiencies in adult germ-free mice, thus implicating a fundamental role for the microbiota in programming mucus barrier generation. In this study, we have investigated the natural neonatal development of the mucus barrier and sentinel goblet cell-dependent secretory responses upon postnatal colonization. Combined in vivo and ex vivo analyses of pre- and post-weaning colonic mucus barrier and sentinel goblet cell maturation demonstrated a sequential microbiota-dependent development of these primary and secondary goblet cell-intrinsic protective functions, with dynamic changes in mucus processing dependent on innate immune signalling via MyD88, and development of functional sentinel goblet cells dependent on the NADPH/Dual oxidase family member Duox2. Our findings therefore identify new mechanisms of microbiota-goblet cell regulatory interaction and highlight the critical importance of the pre-weaning period for the normal development of colonic barrier function.

Effect of the solar radiation pressure on the motion of satellites in almost circular Earth orbits

This paper considers the effect of the solar radiation pressure on the motion of a satellite in an almostcircular low-Earth orbit. The formulation of the problem is due to the need to determine the effect of solar radiation pressure forces on the motion of light commercial Earth remote sensing (ERS) satellites with large surface areas (solar batteries and antennas). The goal is to determine the main regularities of this effect, construct reasonably simple and accurate estimates of changes in orbital parameters for the orbits under consideration, and clarify their physics (cause-and-effect relations) The novelty of this study also lies in the use of variables specially introduced to describe a motion in almost circular orbits. The study assumes that the solar radiation pressure force is constant throughout the entire orbit, and it is concerned with dawn-dusk orbits, which are often used for ERS satellites with radar observation systems. The paper presents simple analytical expressions that describe the main regularities of short-term (several days) changes in orbital parameters. It is shown that the change in the orientation of the orbital plane is determined by the action of the gyroscopic moment. This moment balances the effect of the moment of external forces aimed at changing the orientation and the change in the orientation perpendicular to the direction of the applied moment of the external forces. The main effect of the solar radiation pressure is the excitation of forced oscillations of the orbital radius, whose amplitude linearly increases with time. The maximums of these oscillations (apogee) are at the point where the light pressure forces maximally slow down the motion of the satellite (directed oppositely to the velocity), and the minimums (perigee) are at the point of the maximum motion acceleration. It is shown that the annual movement of the Sun can qualitatively change the picture of the evolution of orbital parameters. For sun-synchronous dawn-dusk orbits, compact analytical solutions for changes in orbital parameters are constructed, and it is shown that the annual movement of the Sun’s declination reverses the direction of evolution of the orbital shape. The calculations showed a reasonably high accuracy of the analytical solutions at the initial stage. The obtained numerical estimates make it possible to evaluate the effect of the solar pressure on changes in orbital parameters.

Advancements in Rechargeable Zn-Air Batteries with Transition-Metal Dichalcogenides as Bifunctional Electrocatalyst.

Zinc-air batteries are promising energy storage devices owing to their high energy density, low cost, and environmental friendliness. However, the development of durable and efficient bifunctional electrocatalysts is a major concern for Zn-air batteries. In this review, we summarize the recent progress on transition metal dichalcogenides (TMDs) as bifunctional electrocatalysts for Zn-air batteries. We discuss the advantages of TMDs, such as high activity, good stability, and tunable electronic structure, as well as the challenges, such as low conductivity, poor durability, and limited active sites. We also highlight the strategies for fine-tuning the properties of TMDs, such as defect engineering, doping, hybridization, and structural engineering, to enhance their catalytic performance and stability. We provide a comprehensive and in-depth analysis of the applications of TMDs in Zn-air batteries, demonstrating their potential as low-cost, abundant, and environmentally friendly alternatives to noble metal catalysts. We also suggest future directions like exploring new TMDs materials and compositions, developing novel synthesis and modification techniques, investigating the interfacial interactions and charge transfer processes, and integrating TMDs with other functional materials. This review aims to illuminate the path forward for the development of efficient and durable Zn-air batteries, aligning with the broader objectives of sustainable energy solutions.

Sodium layered oxide cathodes: properties, practicality and prospects.

Rechargeable sodium-ion batteries (SIBs) have emerged as an advanced electrochemical energy storage technology with potential to alleviate the dependence on lithium resources. Similar to Li-ion batteries, the cathode materials play a decisive role in the cost and energy output of SIBs. Among various cathode materials, Na layered transition-metal (TM) oxides have become an appealing choice owing to their facile synthesis, high Na storage capacity/voltage that are suitable for use in high-energy SIBs, and high adaptivity to the large-scale manufacture of Li layered oxide analogues. However, going from the lab to the market, the practical use of Na layered oxide cathodes is limited by the ambiguous understanding of the fundamental structure-performance correlation of cathode materials and lack of customized material design strategies to meet the diverse demands in practical storage applications. In this review, we attempt to clarify the fundamental misunderstandings by elaborating the correlations between the electron configuration of the critical capacity-contributing elements (e.g., TM cations and oxygen anion) in oxides and their influence on the Na (de)intercalation (electro)chemistry and storage properties of the cathode. Subsequently, we discuss the issues that hinder the practical use of layered oxide cathodes, their origins and the corresponding strategies to address their issues and accelerate the target-oriented research and development of cathode materials. Finally, we discuss several new Na layered cathode materials that show prospects for next-generation SIBs, including layered oxides with anion redox and high entropy and highlight the use of layered oxides as cathodes for solid-state SIBs with higher energy and safety. In summary, we aim to offer insights into the rational design of high-performance Na layered oxide cathode materials towards the practical realization of sustainable electrochemical energy storage at a low cost.

Eggplant NAC domain transcription factor SmNST1 as an activator promotes secondary cell wall thickening.

NAC-domain transcription factors (TFs) are plant-specific transcriptional regulators playing crucial roles in plant secondary cell wall (SCW) biosynthesis. SCW is important for plant growth and development, maintaining plant morphology, providing rigid support, ensuring material transportation and participating in plant stress responses as a protective barrier. However, the molecular mechanisms underlying SCW in eggplant have not been thoroughly explored. In this study, the NAC domain TFs SmNST1 and SmNST2 were cloned from the eggplant line 'Sanyue qie'. SmNST1 and SmNST2 expression levels were the highest in the roots and stems. Subcellular localization analysis showed that they were localized in the cell membrane and nucleus. Their overexpression in transgenic tobacco showed that SmNST1 promotes SCW thickening. The expression of a set of SCW biosynthetic genes for cellulose, xylan and lignin, which regulate SCW formation, was increased in transgenic tobacco. Bimolecular fluorescence and luciferase complementation assays showed that SmNST1 interacted with SmNST2 in vivo. Yeast one-hybrid, electrophoretic mobility shift assay (EMSA) and Dual-luciferase reporter assays showed that SmMYB26 directly bound to the SmNST1 promoter and acted as an activator. SmNST1 and SmNST2 interact with the SmMYB108 promoter and repress SmMYB108 expression. Altogether, we showed that SmNST1 positively regulates SCW formation, improving our understanding of SCW biosynthesis transcriptional regulation.

Complex Hydride-Based Gel Polymer Electrolytes for Rechargeable Ca-Metal Batteries.

Rechargeable Ca batteries offer the advantages of high energy density, low cost, and earth-abundant constituents, presenting a viable alternative to lithium-ion batteries. However, using polymer electrolytes in practical Ca batteries is not often reported, despite its potential to prevent leakage and preserve battery flexibility. Herein, a Ca(BH4)2-based gel-polymer electrolyte (GPE) is prepared from Ca(BH4)2 and poly(tetrahydrofuran) (pTHF) and tested its performance in Ca batteries. The electrolyte demonstrates excellent stability against Ca-metal anodes and high ionic conductivity. The results of infrared spectroscopy and 1H and 11B NMR indicate that the terminal ─OH groups of pTHF reacted with BH4 - anions to form B─H─(pTHF)3 moieties, achieving cross-linking and solidification. Cyclic voltammetry measurements indicate the occurrence of reversible Ca plating/stripping. To improve the performance at high current densities, the GPE is supplemented with LiBH4 to achieve a lower overpotential in the Ca plating/stripping process. An all-solid-state Ca-metal battery with a dual-cation (Ca2+ and Li+) GPE, a Ca-metal anode, and a Li4Ti5O12 cathode sustained >200 cycles, confirming their feasibility. The results pave the way for further developing lithium salt-free Ca batteries by developing electrolyte salts with high oxidation stability and optimal electrochemical properties.

A Review of Capacity Fade Mechanism and Promotion Strategies for Lithium Iron Phosphate Batteries

Commercialized lithium iron phosphate (LiFePO4) batteries have become mainstream energy storage batteries due to their incomparable advantages in safety, stability, and low cost. However, LiFePO4 (LFP) batteries still have the problems of capacity decline, poor low-temperature performance, etc. The problems are mainly caused by the following reasons: (1) the irreversible phase transition of LiFePO4; (2) the formation of the cathode–electrolyte interface (CEI) layer; (3) the dissolution of the iron elements; (4) the oxidative decomposition of the electrolyte; (5) the repeated growth and thickening of the solid–electrolyte interface (SEI) film on the anode electrode; (6) the structural deterioration of graphite anodes; (7) the growth of lithium dendrites. In order to eliminate the problems, methods such as the modification, doping, and coating of cathode materials, electrolyte design, and anode coating have been studied to effectively improve the electrochemical performance of LFP batteries. This review briefly describes the working principle of the LFP battery, the crystal structure of the LFP cathode material, and its electrochemical performance as a cathode. The performance degradation mechanism of LFP batteries is summarized in three aspects—cathode material, anode material, and electrolyte—and the research status of LFP material modification and electrolyte design is emphatically discussed. Finally, the challenges and future development of LFP batteries are prospected.

Thermally stable modification of PEO‐based all‐solid‐state electrolytes via a stretching flow field: Constructing a supportive polymer skeleton

AbstractSince the advent of all‐solid‐state lithium‐ion batteries (ASSLIBs), they have been widely regarded as the ideal high‐temperature‐resistant energy storage devices. The solid‐state electrolyte, a crucial component, should possess high ionic conductivity, excellent flexibility, and significant mechanical strength. Poly(ethylene oxide)‐based all‐solid‐state polymer electrolytes (PEO‐ASSPE) appear to meet these criteria. However, PEO‐ASSPE exhibits poor stability at elevated temperatures, where localized overheating and internal thermal runaway can lead to battery short‐circuit failure. To address these issues, this study employs a ethylene‐methacrylic acid copolymer (EMAA) as a structural support polymer, blended via a eccentric rotor mixer. The homogeneously dispersed EMAA within the PEO matrix forms an interpenetrating network structure and interacts with other components, significantly enhancing the high‐temperature electrochemical stability of the composite polymer electrolytes (CPEs) while maintaining ionic conductivity. Research has demonstrated that when the EMAA content is 40 wt.%, the resulting CPE‐40EMAA exhibit high ionic conductivity (4.07 × 10−4 S cm−1), a high lithium‐ion transference number (0.564), a broad electrochemical stability window (5.1 V), and excellent high‐temperature lithium metal cycling stability (stable cycling for 800 h at current density of 0.1 mA cm−2), which sufficiently meets the electrochemical performance requirements for ASSPEs in high‐temperature energy storage batteries.

High-Performance Bifunctional Electrocatalysts for Flexible and Rechargeable Zn-Air Batteries: Recent Advances.

Flexible rechargeable Zn-air batteries (FZABs) exhibit high energy density, ultra-thin, lightweight, green, and safe features, and are considered as one of the ideal power sources for flexible wearable electronics. However, the slow and high overpotential oxygen reaction at the air cathode has become one of the key factors restricting the development of FZABs. The improvement of activity and stability of bifunctional catalysts has become a top priority. At the same time, FZABs should maintain the battery performance under different bending and twisting conditions, and the design of the overall structure of FZABs is also important. Based on the understanding of the three typical configurations and working principles of FZABs, this work highlights two common strategies for applying bifunctional catalysts to FZABs: 1) powder-based flexible air cathode and 2) flexible self-supported air cathode. It summarizes the recent advances in bifunctional oxygen electrocatalysts and explores the various types of catalyst structures as well as the related mechanistic understanding. Based on the latest catalyst research advances, this paper introduces and discusses various structure modulation strategies and expects to guide the synthesis and preparation of efficient bifunctional catalysts. Finally, the current status and challenges of bifunctional catalyst research in FZABs are summarized.

CNT Composite β-MnO2 with Fiber Cable Shape as Cathode Materials for Aqueous Zinc-Ion Batteries.

Rechargeable aqueous zinc-ion batteries (AZIBs) have developed into one of the most attractive materials for large-scale energy storage owing to their advantages such as high energy density, low cost, and environmental friendliness. Nevertheless, the sluggish diffusion kinetics and inherent impoverished conductivity affect their practical application. Herein, the β-MnO2 composited with carbon nanotubes (CNT@M) is prepared through a simple hydrothermal approach as a high-performance cathode for AZIBs. The CNT@M electrode exhibits excellent cycling stability, in which the maximum specific discharge capacity is 259 mA h g-1 at 3 A g-1, and there is still 220 mA h g-1 after 2000 cycles. The specific capacity is obviously better than that of β-MnO2 (32 mA h g-1 after 2000 cycles). The outstanding electrochemical performance of the battery is inseparable from the structural framework of CNT and inherent high conductivity. Furthermore, CNT@M can form a complex conductive network based on CNTs to provide excellent ion diffusion and charge transfer. Therefore, the active material can maintain a long-term cycle and achieve stable capacity retention. This research provides a reasonable solution for the reliable conception of Mn-based electrodes and indicates its potential application in high-performance AZIB cathode materials.