Saturable Process Research Articles

Bias-induced relaxation phenomena in current temporal behaviors of CdZnTe radiation detectors

The bias-induced temporal behavior of the dark current in CdZnTe radiation detectors essentially determines the detector’s performance, but the traditional electric field dependent Schottky barrier height model cannot explain the complicated current transient behavior observed in experiments. In this work, dark current temporal response in CdZnTe detectors as a function of temperature is investigated both experimentally and numerically. After biasing, the transient current increases for detectors with small barrier heights, while decreases for those with large barrier heights before reaching the steady state. This current saturation process is attributed to the de-trapping of deep level defects. The evolution of the electric potential, electric field and trap occupancy in the detector is simulated, which shows an agreement with the measurement results. Schottky barrier height dependent electric potential distribution between bulk material and depletion layer at the blocking contact is responsible for different dark current temporal behavior in CdZnTe detectors.

Dehydrogenation of AlSi7Fe1 Melt during In Situ Composite Production by Oxygen Blowing

The technology of producing a composite material in situ envisages the pre-saturation of an AlSi7Fe1 melt with hydrogen; afterwards, the melt is blown with oxygen until the hydrogen dissolved in the melt is burned out. The hydrogen content was researched during the manufacturing process of the composite material; before oxygen blowing, and at incomplete and complete burning out of the dissolved hydrogen. The interrelation between the absorbed hydrogen content and the aluminum oxide fraction was identified. A mathematical model was proposed which demonstrated that during the saturation process of the melt with oxide particles, hydrogen was absorbed on their surface as a layer close to monoatomic, which does not lead to the realization of the pores’ heterogeneous nucleation mechanism. Due to this, castings produced from the researched composite material are leakless. Incomplete burning out of hydrogen dissolved in the melt leads to the formation of significant hydrogen porosity. The proposed method of prevention of gas porosity in cast composites is an alternative to the conventional one and offers not only the purging of the melt from oxide inclusions but, on the contrary, a significant increase in their specific surface, which allows for the reduction in hydrogen content on the inclusion surface to the monoatomic level.

Ozonation of quinoa seeds (Chenopodium quinoa Willd.): saturation and decomposition kinetics of ozone and physiological quality of seeds

Ozonation has been evaluated as an alternative method for seed treatment. In this context, the goal of this study was to evaluate the saturation process and kinetics of decomposition of ozone in a porous medium composed of quinoa BRS Syetetuba and possible changes in seed quality. Ozone concentration and saturation time in the porous medium and half-life were determined by adopting an inlet ozone concentration of 885 ppm and a flow rate of 5.0 L min-1 at 25 °C. The ozonation periods adopted were 0, 30, 60, 90, and 120 min. Regarding the physiological quality of the seeds, the germination percentage, germination speed index, electrical conductivity, and length of the shoot, root, and normal seedlings were analyzed. At the inlet ozone concentration of 885 ppm and a flow rate of 5.0 L min-1, the saturation concentration and saturation time in the porous medium composed of quinoa were 522.5 ppm and 12.0 min, respectively. The half-life of ozone in the porous medium was 6.08 min at 25 °C. Under these conditions, ozonation did not affect the physiological quality of quinoa BRS Syetetuba seeds for up to 120 min.

Enhanced oil recovery application in low permeability formations by the injections of CO2, N2 and CO2/N2 mixture gases

Low oil recovery which is very predominant in shale oil reservoirs has stimulated petroleum engineers to investigate the applications of enhanced oil recovery methods in these formations. One such application is the injection of gases into the formation to stimulate increased oil recovery. In many gas flooding projects performed in the field, the miscibility of the gas injected is usually the most desired displacement mechanism, and carbon dioxide (CO2) gas has been recognized to be the best performing gas for injection due to its ability to be miscible with oil in the reservoir at low pressures compared to other gases such as nitrogen. This minimum miscibility pressure (MMP) is of very crucial importance because it is the primary limiting factor in the feasibility of a miscible gas flooding project. However, there are other limiting factors such as cost and availability and, in these instances, nitrogen (N2) and lean gas are the more preferred candidate as opposed to carbon dioxide gas. Mixing carbon dioxide gas with lean gas or with nitrogen in a required ratio can allow us to design an injection gas that will be suitable enough to satisfy both the availability and cost constraints and at the same time allow us to achieve a reachable and reasonable miscibility pressure. The objective of this paper is to investigate the effect of mixing nitrogen gas and carbon dioxide gas in a 50:50 ratio on oil recovery in tight oil formations. The experiment was performed with controlled constraints such as the same core sample, same crude oil and same core cleaning and saturation process which was repeated for each trial. The oil used was live oil from Eagle ford formation, and the gases used were nitrogen (99.9% purity), carbon dioxide and a mixture of nitrogen and carbon dioxide in a 50:50 ratio. The injection pressure ranged from 1000 to 5000 psi with pressure increments of 1000 psi, and the same flooding time was 6 h. The potential of the N2, CO2 and N2–CO2 mixture for improving oil recovery was assessed along with the breakthrough time. The results showed that CO2 gas had the highest recovery followed by the N2–CO2 mixture and N2 gas had the lowest recovery. The gas breakthrough time results showed that the N2–CO2 mixture had the longest breakthrough time, N2 had the shortest breakthrough time, and CO2 had a significantly longer breakthrough time than pure N2 gas. The RF increased with increasing pressure, but the gas breakthrough time decreased with increasing pressure. However, the incremental RF decreased in all three cases when the injection pressure was above 3000 psi.

“Cultural-historical meanings of the Third Rome”

In theoretical and sociopolitical discourses, the semantic construct “The Third Rome" is often used in denotative meaning of imperial ideology. At the same time, it has multivariate connotation, the disclosure of which in the cultural-historical context on the one hand allows deeper understanding of the semantic aspect of the construct, while on the other – more precisely characterizing the culture of different epochs. The object of this research is the historical process of saturation of the semantic construct “The Third Rome" with meaningful content. The subject of this research is the basic cultural- historical connotations the concept “The Third Rome”. The goal of this work is to establish correlation between the basic connotations of the concept under review and the historical cultures by means of culturological attribution. Alongside the general theoretical philosophical-analytical toolset, the author tests the method of culturological attribution in relation to cultural-historical meanings of the concept “The Third Rome" as intangible cultural artifacts. The novelty of this article consists in elucidation of the historical subjectivity of cultural meanings of the concept “The Third Rome”. Attribution of this concept to several historical cultures allows determining its multiple connotation, which at times are antipodal. The most common interpretation (“The Third Rome” as an empire) is applicable only to certain historical cultures.

Twisted intramolecular motion arrested in aggregated state emission and the nonlinear optical properties of pyrene pyrazoline derivatives

Heterocyclic pyrene pyrazoline moieties containing similar structures but with differences in thiophene (PPT), furan (PPF) and pyridine (PPP) substitutions at the terminal molecules were synthesized. Their aggregation behaviour in THF-water mixtures was investigated and results demonstrated that PPT and PPP exhibited aggregation-induced emission (AIE), whereas PPF exhibited aggregation-induced blue-shifted emission (AIBSE). PPT and PPP provided red-shifted emission, while PPF had observed blue-shifted emission at high water fractions of 70-90%, confirming that aggregation effects played a major role in the molecular structure. Two emission peaks from locally excited and twisted intramolecular charge transfer confirmed the twisted nature from the dihedral angle values of the free reorganized molecules that were completely restricted in high water fractions due to molecular aggregation. This was further confirmed from colour Commission Internationale de l'Eclairage values as well as dynamic light scattering analysis. Third-order nonlinear optical properties were studied using a Nd:Yag laser beam Z-scan technique at 532 nm. The open aperture Z-scan revealed that PPT and PPF towards the peak point endured strong saturable absorption, whereas PPP indicated a strong reverse saturable absorption process. The AIE and AIBSE mechanisms from undergoing restricted twisting intramolecular motion in the aggregated luminogens provide great insight into new developments in AIEgen materials for these optoelectronic materials.

The canopy layer, a biogeochemical actor in the forest N-cycle

Atmospheric nitrogen (N) depositions have increased sharply since the industrial revolution. Numerous authors forecasted severe impacts on forest ecosystem services and functioning when new N input exceeds both biotic and abiotic holding capacity, in what is known as the N saturation process. However, most of the studies performed so far to quantify these impacts have largely neglected the potential role of the canopy and associated biota in biogeochemical processes. The present review collects and summarizes the existing literature about all the interactions of atmospheric N deposition and the canopy, evidencing different processes that may interfere with them. By summarizing the research of the last three decades, we found that a share of both wet and dry N deposition can be retained within the canopy, partially absorbed by the leaves or other aerial parts and utilized for plant metabolism, substantially changing the fate of N in the ecosystem. Focusing on canopy-associated biota, we analyzed how this compartment can represent a highly reactive layer and have an active role in different processes involved in the N cycle such as nitrification, fixation and volatilization. It emerges clearly that the canopy hosts a complex network of processes; however, despite this, most of the manipulative experiments failed to include the canopy into the studies. The documented manipulative experiments which included the canopy are mainly short-term and represent very few forest types. Moreover, we highlighted a lack of research concerning the interaction between the complex network of canopy processes, atmospheric N deposition and other global change factors, such as increasing atmospheric CO2 concentration, increasing temperature and drought events.

Third‐Order Nonlinear Optical Response of Few‐Layer MXene Nb2C and Applications for Square‐Wave Laser Pulse Generation

AbstractNiobium carbide (Nb2C), a newly developed 2D MXene material, has attracted much attention due to its outstanding electronic and optical properties. In this work, few‐layer 2D Nb2C nanosheets are synthesized by magnetron sputtering deposition method. Z‐scan measurements with pump source operating at 1.0 µm are performed to study the third‐order nonlinear optical response, revealing excellent light modulation capabilities of 2D Nb2C. The effective nonlinear absorption coefficient (βeff ≈ –105 cm GW–1) caused by saturable absorption effect is determined to be two orders of magnitude larger than that induced by reverse saturable absorption processes (two‐photon absorption, etc.). The positive nonlinear refractive index n2 is determined to be ≈10–13 m2 W–1 for the first time. Moreover, by decorating 2D Nb2C onto microfiber, microfiber‐based 2D Nb2C saturable absorber is fabricated and applied for compact square‐wave pulse mode‐locking ytterbium‐fiber laser. The pulse duration of SWP increases from 0.652 to 1.616 ns with the pulse energy increasing linearly up to 0.89 nJ while the peak power remains a constant. The results not only verify the capability of 2D Nb2C as an optical modulator, but also pave a new way for exploring SWP laser sources.

Chloride migration in cement mortars with ultra-low water to binder ratio

This paper investigates the influences of supplementary cementitious materials (SCMs) on the compressive strength and chloride ion permeability of cement mortar with ultra-low water to binder ratio. The applicable of rapid chloride migration (RCM) test on the evaluation of chloride penetration resistance is studied. Test results show that with the decreased specimen thickness and extended standing time during water saturation process, the chloride migration coefficient of cement mortars with ultra-low water to binder ratio can be measured with sufficient testing duration. Within a specific range of replacement level, the replacement of cement with SCMs such as slag, fly ash and silica fume significantly densifies the pore structure and increase the compressive strength and chloride penetration resistance of cement mortar, especially for the cement mortar with silica fume. When more than one type of SCMs are incorporated, the cement mortars with silica fume and slag or fly ash show superior performance than other mixtures.A good linear relationship exists between compressive strength and porosity of cement mortars. Compared to the total porosity, the chloride migration coefficient is more affected by the volume of pores with diameter larger than 20 nm within cement mortars.

Field-induced phase transitions of tetramer-singlet states in synthetic SU(4) magnets

Phase transitions of quantum dimer magnets can be explained in terms of Bose-Einstein condensation of magnons. Here we consider a natural extension of the dimer magnets to SU(4)-symmetric tetramer systems, which could be created with four nuclear-spin components (named “u,” “d,” “c,” and “s”) of 173Yb atoms in optical superlattices. We apply the cluster mean-field approximation to the SU(4) Heisenberg model on a tetramerized square lattice, and study the phase transition phenomena in the presence of the field that creates a population imbalance between the two components u,d and the other two c,s. When the population of the four components is balanced, the ground state is approximately given by the direct product of local SU(4)-singlet states. When the field is applied, the population ratio of the components u and d is increased and the system eventually reaches a “saturated” state, which is a SU(2) system with only u and d. We show that in the saturation process, the system exhibits two successive step-like transitions, in contrast to the standard dimer magnets with continuous transition process associated with Bose-Einstein condensation of magnons. The intermediate phase in between the two step-like transitions is a nontrivial solid phase with alternating arrangement of the SU(4)-singlet and four-site resonating-valence-bond states.

On a threshold of desorption during the pumping of a nanofluid through porous medium

The results of direct numerical simulation are intended to describe the saturation process of a nanofluid through artificial porous medium. The calculations were fulfilled using the hypothesis, which presumed the adsorptive nature of nanoparticles adhesion to the solid boundaries of pores. Mathematical statement of the problem was based on the modified MIM-model and Darcy – Boussinesq equations. The dependence of the desorption intensity on the value of filtration velocity was taken into account in the course of theoretical investigation. It was shown that this factor for concentration redistribution of the immobile impurity led to the steepening of the wave front as a function of time. Phenomenological realization of novel physical assumptions made the results of numerical modeling closer to the experimental data.

Ultra-high optical nonreciprocity with a coupled triple-resonator structure

Optical transmission nonreciprocity as a widely investigated phenomenon is essential to various applications. Many sophisticated mechanisms have been proposed and tested for achieving the optical nonreciprocity on integrated scale, but the technical barriers still exist to their practical implementation. To have an ultra-high transmission nonreciprocity, we consider a simple physical mechanism of optical gain saturation applied to a structure of three mutually coupled cavities or fiber rings. The gain saturation processes in two of its components creates a significantly enhanced optical nonreciprocity that satisfies the requirements for the realistic applications. The structure enjoys two advantages of its wide working bandwidth and the flexibility in choosing its components. Moreover, it is possible to apply the structure to a faithful and non-reciprocal transmission of broadband pulse signals. The structure may considerably relax the constraints on the integrated photonic circuits based on the current technology.

Impact of compost reactive layer on hydraulic transport and C & N cycles: Biogeochemical modeling of infiltration column experiments

Managed Aquifer Recharge (MAR) is a key strategy to increase freshwater resources in many regions facing water scarcity. MAR issues are related to both quantity and quality of the infiltrating water. In most countries, very high quality of the infiltrating water is required, to limit the impact on the aquifer geochemistry. In this paper, the possibility of injecting water of lower quality in the aquifer and letting the biogeochemical reactions take place in order to enhance its quality is explored. Here, we present the fate of nutrients (C, N) in the biogeochemical system of a reactive barrier formed by mixture of different proportions of sand and compost, supplied with treated wastewater to mimic MAR. An integrated conceptual model involving the nutrient cycles and biomass dynamics (auto- and heterotrophic) was developed, and then tested with a number of solute transport experiments in columns with different compost fraction in the column filling. The model incorporated both saturation and inhibition processes (regarding the nutrients and their byproducts) to provide a comprehensive picture of the nutrient dynamics within the column. The model developed (three if considering the 3 column setups) allowed to discriminate the processes that govern the fate of nutrients in relation with the compost enhancing long-term nutrient degradation, yet hindering hydraulic parameters that affect infiltration rates.

In Vitro Evidence of Potential Interactions between CYP2C8 and Candesartan Acyl-β-D-glucuronide in the Liver.

Growing evidence suggests that certain glucuronides function as potent inhibitors of CYP2C8. We previously reported the possibility of drug-drug interactions between candesartan cilexetil and paclitaxel. In this study, we evaluated the effects of candesartan N2-glucuronide and candesartan acyl-β-D-glucuronide on pathways associated with the elimination of paclitaxel, including those involving organic anion-transporting polypeptide (OATP) 1B1, OATP1B3, CYP2C8, and CYP3A4. UDP-glucuronosyltransferase (UGT) 1A10 and UGT2B7 were found to increase candesartan N2-glucuronide and candesartan acyl-β-D-glucuronide formation in a candesartan concentration-dependent manner. Additionally, the uptake of candesartan N2-glucuronide and candesartan acyl-β-D-glucuronide by cells stably expressing OATPs is a saturable process with K m of 5.11 and 12.1 μM for OATP1B1 and 28.8 and 15.7 μM for OATP1B3, respectively; both glucuronides exhibit moderate inhibition of OATP1B1/1B3. Moreover, the hydroxylation of paclitaxel was evaluated using recombinant CYP3A4 and CYP3A5. Results show that candesartan, candesartan N2-glucuronide, and candesartan acyl-β-D-glucuronide inhibit the CYP2C8-mediated metabolism of paclitaxel, with candesartan acyl-β-D-glucuronide exhibiting the strongest inhibition (IC50 is 18.9 µM for candesartan acyl-β-D-glucuronide, 150 µM for candesartan, and 166 µM for candesartan N2-glucuronide). However, time-dependent inhibition of CYP2C8 by candesartan acyl-β-D-glucuronide was not observed. Conversely, the IC50 values of all the compounds are comparable for CYP3A4. Taken together, these data suggest that candesartan acyl-β-D-glucuronide is actively transported by OATPs into hepatocytes, and drug-drug interactions may occur with coadministration of candesartan and CYP2C8 substrates, including paclitaxel, as a result of the inhibition of CYP2C8 function. SIGNIFICANCE STATEMENT: This study demonstrates that the acyl glucuronidation of candesartan to form candesartan acyl-β-D-glucuronide enhances CYP2C8 inhibition while exerting minimal effects on CYP3A4, organic anion-transporting polypeptide (OATP) 1B1, and OATP1B3. Thus, candesartan acyl-β-D-glucuronide might represent a potential mediator of drug-drug interactions between candesartan and CYP2C8 substrates, such as paclitaxel, in clinical settings. This work adds to the growing knowledge regarding the inhibitory effects of glucuronides on CYP2C8.

Intense terahertz generation from photoconductive antennas.

In this paper, we review the past and recent works on generating intense terahertz (THz) pulses from photoconductive antennas (PCAs). We will focus on two types of large-aperture photoconductive antenna (LAPCA) that can generate high-intensity THz pulses (a) those with large-aperture dipoles and (b) those with interdigitated electrodes. We will first describe the principles of THz generation from PCAs. The critical parameters for improving the peak intensity of THz radiation from LAPCAs are summarized. We will then describe the saturation and limitation process of LAPCAs along with the advantages and disadvantages of working with wide-bandgap semiconductor substrates. Then, we will explain the evolution of LAPCA with interdigitated electrodes, which allows one to reduce the photoconductive gap size, and thus obtain higher bias fields while applying lower voltages. We will also describe recent achievements in intense THz pulses generated by interdigitated LAPCAs based on wide-bandgap semiconductors driven by amplified lasers. Finally, we will discuss the future perspectives of THz pulse generation using LAPCAs.

Analysis and experimental application of a dead‐time compensator for input saturated processes with output time‐varying delays

Dead-time compensators (DTCs) are a family of classical controllers derived from the Smith Predictor (SP). Their main characteristic is that they explicitly employ the model of the open-loop process to feedback a predicted value of the non-delayed system, thus obtaining \textit{compensation} of the delay. Such a perfect compensation is not achievable in the case of time-varying delays. In this paper, we address stability analysis of a DTC structure in this situation, in addition to considering saturating actuators and disturbances of limited energy. Specific challenges related to the DTC closed loop are taken into account in the developed theoretical conditions, which are expressed in terms of linear matrix inequalities (LMIs) by using an adequate Lyapunov-Krasovskii functional (LKF) and generalized sector conditions. Furthermore, a new approach for the definition of the set of initial conditions in an augmented space in conjunction with the LKF is presented. Besides theoretical innovations, practical discussion about the relation between the tuning of DTC controllers and robustness for this class of systems is presented through numerical examples. An experimental application on a neonatal incubator prototype is carried out to emphasize the effectiveness of the results.

Structural and Optical Coefficients Investigation of γ-Al2O3 Nanoparticles using Kramers-Kronig Relations and Z–scan Technique

ABSTRACT γ-Al2O3 nanoparticles (NPs) with a mean diameter of 60 nm were prepared through the sol–gel technique and characterized by X-ray diffraction, field emission scanning electron microscopy (FESEM), and ultraviolet–visible (UV-Vis) spectroscopy. The formation of cubic structures with the γ phase for Al2O3 NPs confirms. The average particle size obtained is about 60 nm by the FESEM image. The nonlinear optical properties were examined by a single-beam Z-scan method using a Gaussian visible continuous wave Nd:YAG laser (532 nm). The Z-scan findings indicated a self-focusing nonlinearity and saturable absorption process in order of 10−8 (cm2/W) and 10−4 (cm/W) in the synthesized γ-Al2O3 NPs, respectively. Moreover, Kramers–Kronig relations were applied to determine the complex refractive index and dielectric coefficient of the specimens by Fourier-transform infrared spectroscopy. The transversal and longitudinal optical (TO and LO) modes are the two intersection points in the real and imaginary parts of the complex refractive index. Also, the maximum position of the Im(−1/ ε) plot is related to LO frequency.

Railway freight node capacity evaluation: a timetable-saturation approach and its application to the Novara freight terminal

This paper presents a timetable-based approach to assess the capacity of a railway freight node, based on the microscopic simulation and saturation of the timetable. Saturation is done by scheduling additional saturation train paths without introducing any traffic conflict, while respecting the required technical and operational constraints, until no more paths can be added. The approach is applied to analyze the potential effects on capacity of some infrastructure improvements planned by Rete Ferroviaria Italiana (RFI) for the rail freight node of Novara, Italy. The capacity is evaluated by means of two KPIs computed on saturated timetables: the number of daily pairs of saturation freight trains and the infrastructure Occupancy Time Rate (OTR). The first KPI represents an absolute estimation of the capacity (theoretical or practical, depending on the presence of buffer times). Instead, the OTR is computed by the UIC 406R compression method and it is used to identify local bottlenecks. For the analysis, we use SASTRE, an analysis environment for railway systems developed at Politecnico di Torino, which combines a MILP formulation for the timetable saturation problem with a saturation strategy layer. The saturation strategy considers a given set of priorities between the different network areas and the train types to be used during the saturation process. The results reveal that using a microscopic model to schedule traffic flows on a complex railway node allows for a good accuracy of the timetable, but at a high computational cost.

A Ku-Band Compact Disk-Beam Relativistic Klystron Oscillator Operating at Low Guiding Magnetic Field

The disk-beam relativistic klystron oscillator (DB-RKO) with the radial-line high frequency structure is one of the attractive high power microwave (HPM) sources due to its specific virtues of weak space-charge effect, high power handling capacity and strong electron collection ability. However, such a device generally exhibits a bulky volume in the radial direction, retarding its actual applications in some compact occasions. Besides, it usually saturates slowly because of the insufficient beam-wave coupling strength. For this purpose, a compact DB-RKO with a rapid saturation process is proposed and physically designed in this paper. By compressing the axial width of the electron beam drift tube suitably, the beam-wave coupling strength is enhanced clearly and the saturation process is accelerated significantly. The whole beam-wave interaction structure is shortened with a radial length of about 5 cm. Besides, in order to increase the device compactness further, an improved magnetic-excited method is presented to enhance the magnetic field in the diode area by introducing a pair of soft-magnets. Furthermore, with the guiding of a low magnetic field of 0.4 T, the compact DB-RKO is experimentally demonstrated to be capable of generating Ku-band HPM radiations with a peak power of 810 MW, a power conversion efficiency of 28%, a center frequency of 14.19 GHz and a pulse duration of about 27 ns. The proposed DB-RKO is promising for the package of the permanent magnets which are preliminarily designed in this paper.

MEDIUM-TERM OSCILLATIONS OF THE SOLAR ACTIVITY

In addition to the well-known 11-year cycle, longer and shorter characteristic periods can be isolated in variations of the parameters of helio-geophysical activity. Periods of about 36 and 60 years were revealed in variations of the geomagnetic activity and an approximately 60-year periodicity, in the evolution of correlation between the pressure in the lower atmosphere and the solar activity. Similar periods are observed in the cyclonic activity. Such periods in the parameters of the solar activity are difficult to identify because of a limited database available; however, they are clearly visible in variations of the asymmetry of the sunspot activity in the northern and southern solar hemispheres. In geomagnetic variations, one can also isolate oscillations with the characteristic periods of 5-6 years (QSO) and 2-3 years (QBO). We have considered 5-6-year periodicities (about half the main cycle) observed in variations of the sunspot numbers and the intensity of the dipole component of the solar magnetic field. A comparison with different magnetic dynamo models allowed us to determine the possible origin of these oscillations. A similar result can be reproduced in a dynamo model with nonlinear parameter variations. In this case, the activity cycle turns out to be anharmonic and contains other periodicities in addition to the main one. As a result of the study, we conclude that the 5-6-year activity variations are related to the processes of nonlinear saturation of the dynamo in the solar interior. Quasi-biennial oscillations are actually separate pulses related little to each other. Therefore, the methods of the spectral analysis do not reveal them over large time intervals. They are a direct product of local fields, are generated in the near-surface layers, and are reliably recorded only in the epochs of high solar activity.