Ringer's Solution Research Articles

In-vitro biocompatibility, antibacterial activity, and corrosion resistance of HA-TiO2/ZnO coating fabricated by plasma electrolytic oxidation on Ti6Al4V

The hydroxyapatite/Zinc Oxide (HA-TiO2/ZnO) coatings were grown on the Ti6Al4V substrate by plasma electrolyte oxidation from the CaP-based electrolyte containing 1, 3, and 6 g/L ZnO nanoparticles. XRD results confirmed the presence of ZnO, HA, and rutile phases in all coatings. According to SEM observations, coatings presented the porous morphology as a result of micro-arc discharges during the PEO process, whereas some of the pores in the composite coatings were filled by ZnO proportional to its content. After 7 days of immersion in SBF solution, accumulations of bone-like clusters were visible on the surface, demonstrating a promising bio-mineralization ability for all coatings, although the higher amount of 6 g/L ZnO had partially an inhibitory effect on the apatite nucleation. In-vitro studies demonstrated a time and concentration-dependent impact of ZnO on the viability of MG-63 osteoblast-like cells so that the concentration of 3 and 6 g/L caused the death of some cells after 7 days. The antibacterial tests also showcased that the presence of ZnO decreased the activity of gram-negative bacteria (E. coli) and gram-positive bacteria (S. aureus), while the higher concentration of ZnO particles led to more antibacterial activity of the coating. Finally, evaluating the corrosion behavior of PEO coatings through a potentiodynamic polarization test in Ringer's solution manifested a better protection against corrosion by increasing the ZnO content in the coating, mainly owing to the blocking of the pores by the ZnO particles, and as a result, the greater difficulty of electrolyte to reach the titanium substrate.

Influence of Zirconium on the Microstructure, Selected Mechanical Properties, and Corrosion Resistance of Ti20Ta20Nb20(HfMo)20-xZrx High-Entropy Alloys.

The presented work considers the influence of the hafnium and molybdenum to zirconium ratio of Ti20Ta20Nb20(HfMo)20-xZrx (where x = 0, 5, 10, 15, 20 at.%) high-entropy alloys in an as-cast state for potential biomedical applications. The current research continues with our previous results of hafnium's and molybdenum's influence on a similar chemical composition. In the presented study, the microstructure, selected mechanical properties, and corrosion resistance were investigated. The phase formation thermodynamical calculations were also applied to predict solid solution formation after solidification. The calculations predicted the presence of multi-phase, body-centred cubic phases, confirmed using X-ray diffraction and scanning electron microscopy. The chemical composition analysis showed the segregation of alloying elements. Microhardness measurements revealed a decrease in microhardness with increased zirconium content in the studied alloys. The corrosion resistance was determined in Ringer's solution to be higher than that of commercially applied biomaterials. The comparison of the obtained results with previously reported data is also presented and discussed in the presented study.

Urinary syndecan-1 in dogs anesthetized with isoflurane or sevoflurane: A randomized, prospective study.

Syndecan-1 (SDC1) is an established marker of endothelial glycocalyx shedding. Most research on SDC1 has focused on plasma or serum concentrations, and little is known about urine concentrations. Measure urinary SDC1 concentrations in dogs undergoing anesthesia with either sevoflurane or isoflurane and assess the effects of anesthesia duration and IV crystalloids on urinary SDC1 concentrations. Thirty-one client-owned dogs undergoing anesthesia for magnetic resonance imaging (MRI) with or without surgery for suspected intervertebral disk disease (IVDD) were used. Dogs with suspected IVDD were randomized to undergo anesthesia with either sevoflurane or isoflurane. Urine was collected before and immediately after anesthesia for the analysis of SDC1. Urinary creatinine concentrations also were measured, and the ratio of urinary SDC1 to urinary creatinine (USCR) was used to account for dilution. Median (range) USCR was significantly higher after anesthesia compared with baseline for all groups combined (P < .05). No significant difference was found between the groups for age, sex, weight, and type of anesthesia. Multiple regression analysis of the effect of the independent variables inhalant type, age, weight, sex, anesthesia time, surgery, and quantity of IV fluids on the dependent variable SDC1 found that only the quantity of IV fluids significantly predicted a change (P < .001). The total volume of lactated Ringer's solution administered to anesthetized dogs may affect USCR. Further investigations are warranted to evaluate the relationship between IV fluids and SDC1.

#1887 Comparison of the efficacy of preservation at 22°C versus 4°C in warm ischemic kidneys from MHC-inbred CLAWN miniature swine

Abstract Background and Aims Static cold preservation, the standard in transplantation, is primarily aimed at reducing metabolic and oxygen demand. Kidney transplantation from donors after cardiac death (DCD) addresses the shortage of donor organs, but these kidneys are susceptible to cold preservation. A previous study using small animal models demonstrated the potential benefits of preserving DCD kidneys at a warmer temperature of 22°C using extracellular-type solutions (Iwai S., PLoS One 2012). Based on this foundational research, our study aimed to evaluate the efficacy of preserving warm ischemic kidneys at temperatures of either 4°C or 22°C using preclinical large animal miniature swine models. Method After 2 hours of warm ischemia, the pig kidneys were preserved for 60 minutes at either 4°C or 22°C with extracellular-type solutions (ETK®). In Experiment 1, these preserved kidneys underwent ex-vivo perfusion for 120 minutes at 37°C with a mean arterial pressure of 85 mmHg. This perfusion used a Ringer's solution supplemented with red blood cells, aiming to determine the early functionality of kidneys subjected to 2-hour warm ischemia in transplantation and to assess whether preservation at 4°C or 22°C could maintain renal function during the acute postoperative period (n = 3 in each group). During this period, both physiological parameters (renal blood flow, intrarenal resistance, and urine output) and metabolic parameters (oxygen consumption) were evaluated. In Experiment 2, kidneys that underwent similar warm ischemia and preservation procedures were transplanted into MHC-matched recipients. These recipients received continuous tacrolimus treatment for 12 days to minimize rejection due to minor antigen differences. After transplantation, renal function was monitored and assessed by serum creatinine levels and renal biopsies for 14 days (n = 3 in each group). Results Experiment 1 demonstrated that kidneys subjected to 2 hours of warm ischemia and then preserved at 22°C had better physiological and metabolic indices during a subsequent 2-hour ex-vivo perfusion compared to those preserved at 4°C. The results were as follows: 22°C vs. 4°C—mean renal blood flow (27 ± 5 vs. 10 ± 0 ml/min), intrarenal resistance (3.5 ± 0.5 vs. 8.7 ± 0.1 mmHg/ml/min), total urine volume (14 ± 5 vs. 5 ± 4 ml), and oxygen consumption (224 ± 39 vs. 93 ± 16 ml/min/g). Importantly, there was no complete cessation of blood flow in either group, indicating the potential for long-term evaluation using a transplantation model. In Experiment 2, kidneys preserved at 22°C resulted in significantly lower peak post-transplant serum creatinine levels compared to those preserved at 4°C (3.9 ± 0.6 mg/dl vs 8.9 ± 0.3 mg/dl, p = 0.0015). There was a marked decrease in the area under the curve of creatinine from day 0 to day 14, with a 36% reduction from 61 mg/dL per day in the 4°C group to 39 mg/dL per day in the 22°C group. Renal biopsies performed on post-operative day 4 revealed extensive necrosis in the renal tubules of kidneys stored at 4°C. In contrast, kidneys preserved at 22°C showed more localized damage. In addition, PCNA staining indicated accelerated regeneration of the tubular epithelium in kidneys preserved at 22°C. Conclusion This study demonstrates that kidneys subjected to 2 hours of warm ischemia from MHC-inbred miniature swine are more effectively preserved at 22°C than at 4°C when using an extracellular-type solution. To our knowledge, this is the first report demonstrating the efficacy of organ preservation at 22°C in clinically relevant, large animal models. From the evaluation of ex-vivo perfusion of preserved kidneys, it was suggested that kidneys preserved at 22°C maintain better blood perfusion to severely ischemic kidneys immediately after transplantation, which leads to the rapid recovery of renal function of acute kidney injury. Future research will focus on elucidating the mechanisms underlying the superior outcomes associated with 22°C preservation. In addition, investigations will be conducted to determine whether similar benefits can be achieved using intracellular-type solutions, which are more commonly used in renal transplantation.

Traditional vs. modified Ringer lactate-based del Nido cardioplegia impacts on clinical outcomes in patients undergoing coronary artery bypass grafting: results from a clinical trial

Introduction: myocardial protection with cardioplegia solution is one of the precautions during coronary bypass grafting surgery (CABG) with cardiopulmonary bypass (CPB) to reduce myocardial damage and ischemia/reperfusion injuries. Unfortunately, the major component of the del Nido cardioplegia solution, Plasma-Lyte A, is unreachable in Iran due to high cost. Therefore, we have utilized lactate Ringer's solution as the base solution for our modified del Nido solution (LR DN). Study design and methods: the present clinical trial was performed on 18-75 year old patients (EF&gt;35%) undergoing CABG with CPB in Imam Hossein hospital Tehran-Iran in 2021. Patients were randomly allocated to LR DN (modified del Nido cardioplegia) and PL DN (standard del Nido cardioplegia solution) groups. Serum level of cardiac troponin I (cTnI) at baseline, declamp, ICU admission, and 24 hours after admission, the type and dosage of inotrope agents, EF, rate of arrhythmia after clamp removal and lactate level were measured and compared between groups. Results: 109 patients were recruited. There were no statistically significant differences between the PL DN cardioplegia and LR DN groups for cardiopulmonary bypass times, cardiac enzymes, transfusion requirements, and arterial blood gases. However, postoperative serum levels of cTnI among patients in the LR DN group was significantly higher than patients of the PL DN group after ICU admission and 24 hours postoperatively. Also, more patients needed epinephrine administration in the operating room in the LR DN group (29.8% vs. 11.5%; p: 0.019 vs. PL DN group). Conclusion: we concluded that standard del Nido cardioplegia solution offers better myocardial protection compared with Ringer's lactate-based del Nido cardioplegia in adult patients undergoing CABG with CPB. We recommend using standard del Nido cardioplegia with a base of Plasma-Lyte A for patients presenting for CABG surgery.

Wear Rate, Tribo-Corrosion, and Plastic Deformation Values of Co-Cr-Mo Alloy in Ringer Lactate Solution.

This study investigates the tribocorrosion performance of a cast Co-Cr-Mo alloy prepared using casting and electromagnetic stirring (EMS) at specific frequencies. The tribocorrosion behaviour of the alloy was evaluated when exposed to Ringer's lactate solution to optimize the EMS parameters and improve its properties. The research focuses on biomedical implant applications and explores how EMS affects alloy wear and corrosion resistance. As did the friction coefficient and wear volume, the wear rate of samples produced with EMS frequencies of 75 Hz and 150 Hz decreased. These improvements are attributed to the ability of EMS to refine grain size and homogenize the microstructure, thereby increasing the resistance to tribocorrosion. Techniques such as scanning electron microscopy (SEM) and profilometry were used for surface and wear analysis, while mechanical properties were evaluated through instrumented indentation tests. The findings confirm that EMS improves the alloy's durability and tribocorrosion resistance, making it highly suitable for demanding biomedical applications such as joint replacements. This highlights the importance of advanced manufacturing techniques in optimizing biomedical alloys for simulated body conditions.

The influence of laser texturing on the tribological behavior of titanium alloy Ti6Al4V in medical applications

This paper analyzes the tribological behavior of the Ti6Al4V ELI alloy subjected to laser texturization for medical purposes. Laser texturing enables one to observe specific patterns of the material surface at established depths. Microtexturing of the samples was performed using a 355 nm picosecond laser. The influence of the microtexturing process (depending on the process parameters) on the geometric parameters of the proposed laser texturing pattern was evaluated. Selected samples were subjected to tribological testing using the ball-on-plate technique in dry and lubricant-sliding methods (in Ringer solution). The wear properties were evaluated by comparing the coefficient friction, wear volumes, and wear ratio. A scanning electron microscope characterized the morphologies of the wear scar and the wear mechanism. The experimental results show that the surface texturing and the changes in microgrooves can reduce wear. The results indicate, that samples after laser texturing were characterized by 15% higher microhardness, compared to those in the initial state. It was found, a 26% reduction in friction coefficient and 29% in the wear volume compared to the smooth, untextured surface samples under lubricated conditions. The decrease in value of the coefficient friction and wear volume for the samples after the laser texturing process is an effect of synergistic of entrapped wear debris in micro-grooves and increased hardness for samples after laser textured.

Reduced congestion and improved response to a fluid/sodium challenge in chronic heart failure patients after initiation of sacubitril/valsartan: The NATRIUM-HF study.

The effects of initiating sacubitril/valsartan in patients with stable heart failure with reduced ejection fraction (HFrEF) on response to fluid and sodium expansion are unknown. We have explored changes in natriuresis, diuresis, and congestion in response to the administration of intravenous fluid/sodium load in patients with HFrEF before as compared to after the initiation of sacubitril/valsartan. At baseline (before sacubitril/valsartan initiation) and 2 and 3 months after the initiation, patients underwent an evaluation that consisted of three phases of 3 h: the rest phase (0-3 h), the load phase (3-6 h) in which 1 L of intravenous Ringer solution was administered, and the diuretic phase (6-9 h) at the beginning of which furosemide was administered. Overall, 216 patients completed the study. In comparison to baseline values, at 2 and 3 months after sacubitril/valsartan initiation, patients' diuresis and natriuresis in response to Ringer administration significantly increased (mean difference: 38.8 [17.38] ml, p = 0.0040, and 9.6 [2.02] mmol, p < 0.0001, respectively). Symptoms and signs of congestion after the fluid/sodium challenge were significantly decreased at months 2 and 3 compared to baseline. Compared to baseline, there was also an increment of natriuresis after furosemide administration on sacubitril/valsartan (9.8 [5.13] mmol, p = 0.0167). There was a significant decrease in body weight in subsequent visits when compared to baseline values (-0.50 [-12.7, 7.4] kg at 2 months, and -0.75 [-15.9, 7.5] kg at 3 months; both p < 0.0001). The initiation of sacubitril/valsartan in HFrEF patients was associated with improvements in natriuresis, diuresis, and weight loss and better clinical adaptation to potentially decongestive stressors.

Effect of Fluid Intake on Acute Changes in Plasma Volume: A Randomized Controlled Crossover Pilot Trial.

Plasma volume (PV) undergoes constant and dynamic changes, leading to a large intra-day variability in healthy individuals. Hydration is known to induce PV changes; however, the response to the intake of osmotically different fluids is still not fully understood. In a randomized controlled crossover trial, 18 healthy individuals (10 females) orally received an individual amount of an isotonic sodium-chloride (ISO), Ringer (RIN), or glucose (GLU) solution. Hemoglobin mass (Hbmass) was determined with the optimized carbon monoxide re-breathing method. Fluid-induced changes in PV were subsequently calculated based on capillary hemoglobin concentration ([Hb]) and hematocrit (Hct) before and then every 10 minutes until 120 min (t0-120) after the fluid intake and compared to a control trial arm (CON), where no fluid was administered. Within GLU and CON trial arms, no statistically significant differences from baseline until t120 were found (p > 0.05). In the ISO trial arm, PV was significantly increased at t70 (+138 mL, p = 0.01), t80 (+191 mL, p < 0.01), and t110 (+182 mL, p = 0.01) when compared to t0. Moreover, PV in the ISO trial arm was significantly higher at t70 (p = 0.02), t110 (p = 0.04), and t120 (p = 0.01) when compared to the same time points in the CON trial arm. Within the RIN trial arm, PV was significantly higher between t70 and t90 (+183 mL, p = 0.01) and between t110 (+194 mL, p = 0.03) and t120 (+186 mL, p < 0.01) when compared to t0. These results demonstrated that fluids with a higher content of osmotically active particles lead to acute hemodilution, which is associated with a decrease in [Hb] and Hct. These findings underpin the importance of the hydration state on PV and especially on PV constituent levels in healthy individuals.

Comparison of shelf-stable and conventional resuscitation products in a canine model of hemorrhagic shock.

Treatment of severe hemorrhagic shock typically involves hemostatic resuscitation with blood products. However, logistical constraints often hamper the wide distribution of commonly used blood products like whole blood. Shelf-stable blood products and blood substitutes are poised to be able to effectively resuscitate individuals in hemorrhagic shock when more conventional blood products are not readily available. Purpose-bred adult dogs (n = 6) were anesthetized, instrumented, and subjected to hemorrhagic shock (mean arterial pressure <50 mm Hg or 40% blood volume loss). Then each dog was resuscitated with one of five resuscitation products: (1) lactated ringers solution and hetastarch (LRS/Heta), (2) canine chilled whole blood (CWB), (3) fresh frozen plasma (FFP) and packed red blood cells (pRBC), (4) canine freeze-dried plasma (FDP) and hemoglobin-based oxygen carrier (HBOC), or (5) HBOC/FDP and canine lyophilized platelets (LyoPLT). Each dog was allowed to recover after the hemorrhage resuscitation event and was then subjected to another hemorrhage event and resuscitated with a different product until each dog was resuscitated with each product. At the time when animals were determined to be out of shock as defined by a shock index <1, mean arterial pressure (mmHg) values (mean ± standard error) were higher for FFP/pRBC (n = 5, 83.7 ± 4.5) and FDP/HBOC+LyoPLT (n = 4, 87.8 ± 2.1) as compared with WB (n = 4, 66.0 ± 13.1). A transient increase in creatinine was seen in dogs resuscitated with HBOC and FDP. Albumin and base excess increased in dogs resuscitated with HBOC and FDP products compared with LRS/heta and CWB ( p < 0.01). Combinations of shelf-stable blood products compared favorably to canine CWB for resolution of shock. Further research is needed to ascertain the reliability and efficacy of these shelf-stable combinations of products in other models of hemorrhage that include a component of tissue damage as well as naturally occurring trauma.

Electrochemical and Mechanical Properties of Hexagonal Titanium Dioxide Nanotubes Formed by Sonoelectrochemical Anodization.

This study aimed to investigate the fabrication and characterization of hexagonal titanium dioxide nanotubes (hTNTs) compared to compact TiO2 layers, focusing on their structural, electrochemical, corrosion, and mechanical properties. The fabrication process involved the sonoelectrochemical anodization of titanium foil in various electrolytes to obtain titanium oxide layers with different morphologies. Scanning electron microscopy revealed the formation of well-ordered hexagonal TNTs with diagonals in the range of 30-95 nm and heights in the range of 3500-4000 nm (35,000-40,000 Å). The electrochemical measurements performed in 3.5% NaCl and Ringer's solution confirmed a more positive open-circuit potential, a lower impedance, a higher electrical conductivity, and a higher corrosion rate of hTNTs compared to the compact TiO2. The data revealed a major drop in the impedance modulus of hTNTs, with a diagonal of 46 ± 8 nm by 97% in 3.5% NaCl and 96% in Ringer's solution compared to the compact TiO2. Nanoindentation tests revealed that the mechanical properties of the hTNTs were influenced by their diagonal size, with decreasing hardness and Young's modulus observed with an increasing diagonal size of the hTNTs, accompanied by increased plastic deformation. Overall, these findings suggest that hTNTs exhibit promising structural and electrochemical properties, making them potential candidates for various applications, including biosensor platforms.

Electrochemical characteristics of nano-structure TiCN coatings on the tool steel deposited by PACVD in various solutions

This study investigates The electrochemical behavior of various nano-structure TiCN coatings prepared using a plasma-assisted chemical vapor deposition technique in acidic and alkaline solutions. The N2/Ar ratio was varied to explore its effect on the microstructure and electrochemical properties of coatings on the steel cold-work tool. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization (PP) measurements were carried out in various corrosive solutions. Field emission scanning electron microscopy and X-ray diffraction were also utilized to evaluate the microstructure and phase detection. The EIS results showed that the resistance of TiCN coatings increased by about 94.3 % based on the equiaxed structure and small size of the coating cluster in 3.5 % wt NaCl solution after 24 h. The lowest corrosion rate with a value of 5.9 µA cm−2 in Ringer's solution at 37 °C after 24 h was attributed to the TiCN coating with the N2/Ar ratio of 0.4 according to exhibiting the highest Ti content and changes in present phases. The N2/Ar ratio of 0.7 effectively increased the impedance resistance to 97.5 % based on PP test results in 3 M H2SO4 solution. This behavior was related to the lowest value of the C/N ratio and the highest coating thickness.

Metformin as an alternative therapeutic intervention in hemorrhagic shock

Hemorrhagic shock (HS) continues to significantly contribute to civilian and military mortality, underscoring the critical need for new resuscitation strategies. Recent discussions have emphasized the pivotal role of impaired oxygen delivery and cellular metabolism in exacerbating HS-related damage. Metformin, a well-established diabetes medication, exhibits promising potential to enhance cellular metabolism and activate pathways linked to improved oxygen uptake, thereby optimizing cellular energy management. Thus, this study aimed to assess metformin's effcacy in ameliorating outcomes in animals subjected to HS. To achieve this, Wistar rats were surgically prepared with femoral artery and vein catheters. HS was induced by controlled blood withdrawal to maintain a mean arterial pressure (MAP) within the range of 35-40 mmHg for 90 minutes. Throughout the protocol, blood pressure (BP) and heart rate (HR) were assessed. The animals were divided into two groups: Lactated Ringer's solution (LR) and LR treated with Metformin (Met). Metformin was administered in three bolus injections: at the start of resuscitation (10mg), 45 minutes into resuscitation (5mg), and 90 minutes into resuscitation (5mg). After 120 minutes, the animals were euthanized, and blood samples were collected for subsequent analysis, including metabolomic profiling of the tricarboxylic acid (TCA) cycle, amino acids, and lipids. Additionally, trypsin-like enzyme activity in the plasma and markers of brain injury were evaluated. Animals treated with Met showed significantly higher systolic blood pressure after resuscitation (LR: 74±5 mmHg vs. LR+Met: 94±3 mmHg) with no significant changes in HR observed. Brain injury markers such as GFAP (Glial fibrillary acidic protein), S100B (astrocytic protein specific to the central nervous system), Tau (microtubule-associated protein), and NFL (axonal protein neurofilament light) were assessed. Animals reperfused with LR and treated with Met displayed a 22% reduction in GFAP levels compared to those reperfused with LR alone, while other markers remained unchanged. Met treatment also led to a reduction in plasmatic metabolites, including Lactate (30%), Succinate (24%), and Fumarate (22%), along with an increase in Citrate (23%) and α-ketoglutarate (24%)—all constituents of the TCA cycle. Additionally, an increase in amino acid metabolites and a decrease in lipid metabolites were observed. Recent research has suggested that HS results in elevated levels of trypsin-like enzymes in the plasma and that inhibiting these enzymes might improve outcomes during resuscitation. Our study revealed that treatment with Met reduced approximately 60% of trypsin-like enzyme activity in the plasma compared to the LR-only group. In conclusion, our study demonstrates that Met, when administered in conjunction with LR as a resuscitation solution, significantly enhances post-resuscitation BP compared to LR alone. This improved outcome may be associated with alterations in the TCA cycle and the inhibition of trypsin-like enzyme activity. However, further investigations are necessary to elucidate the precise role of these changes in the observed enhancements within this experimental model. This work was supported by National Institutes of Health grant R01HL162120. This is the full abstract presented at the American Physiology Summit 2024 meeting and is only available in HTML format. There are no additional versions or additional content available for this abstract. Physiology was not involved in the peer review process.

Treatment of lidocaine-refractory ventricular tachycardia using procainamide in an anesthetized horse.

To highlight the use of procainamide as a potential alternative treatment modality in cases of ventricular tachycardia that are refractory to lidocaine and magnesium sulfate. 1 adult horse weighing 380 kg. A 25-year-old Arabian gelding presented with severe colic signs. Due to persistent pain, it was elected to carry out an exploratory laparotomy. During the procedure a diagnosis of severe, unstable ventricular tachycardia was made based on the ECG findings, with an initial heart rate of 195 beats per minute and severe hypotension. Initial treatment consisted of discontinuing dobutamine and the administration of a 2 mg/kg IV lidocaine bolus followed by a continuous rate infusion at 50 μg/kg/min. Twenty grams magnesium sulfate (5 mg/kg) was administered IV in 1 L of lactated Ringer solution as a slow bolus over 30 minutes. Ventricular tachycardia persisted with poor peripheral pulses, a severely dampened arterial waveform, and a MAP of 30 to 45 mm Hg. Two milligrams/kg IV procainamide was administered over 3 minutes, 3 separate times, at 5-minute intervals. Immediately following the third dose sinus rhythm was detected on the ECG, the arterial waveform improved, and MAP increased to 85 mm Hg. Ventricular tachycardia is a rare but potentially life-threatening complication in horses undergoing general anesthesia. The potential of this arrhythmia to progress to ventricular fibrillation is of grave concern, as the option to attempt to externally defibrillate horses back to normal sinus rhythm does not exist. This case highlights procainamide as a potential option for cases of ventricular tachycardia that are refractory to more standard treatment modalities.

Harnessing extracellular cold-inducible RNA binding protein by PS-OMe miR130: A promising shield against hemorrhage-induced lung injury.

Hemorrhagic shock (HS) poses a life-threatening condition with the lungs being one of the most susceptible organs to its deleterious effects. Extracellular cold-inducible RNA binding protein has emerged as a pivotal mediator of inflammation, and its release has been observed as a case of HS-induced tissue injury. Previous studies unveiled a promising engineered microRNA, designated PS-OMe miR130, which inhibits extracellular cold-inducible RNA binding protein, thereby safeguarding vital organs. In this study, we hypothesized that PS-OMe miR130 serves as a protective shield against HS-induced lung injury by curtailing the overzealous inflammatory immune response. Hemorrhagic shock was induced in male C57BL6 mice by withdrawing blood via a femoral artery cannula to a mean arterial pressure of 30 mm Hg for 90 minutes. The mice were resuscitated with twice the shed blood volume with Ringer's lactate solution. They were then treated intravenously with either phosphate-buffered saline (vehicle) or 62.5 nmol PS-OMe miR130. At 4 hours later, blood and lungs were harvested. Following PS-OMe miR130 treatment in HS mice, a substantial decrease was observed in serum injury markers including aspartate aminotransferase, alanine transaminase, lactate dehydrogenase, and blood urea nitrogen. Serum interleukin (IL)-6 exhibited a similar reduction. In lung tissues, PS-OMe miR130 led to a significant decrease in the messenger RNA expressions of pro-inflammatory cytokines (IL-6, IL-1β, and tumor necrosis factor α), chemokines (keratinocyte-derived chemokine and macrophage inflammatory protein 2), and an endothelial injury marker, E-selectin. PS-OMe miR130 also produced substantial inhibition of lung myeloperoxidase activity and resulted in a marked reduction in lung injury as evidenced by histological evaluation. This was further confirmed by the observation that PS-OMe miR130 significantly reduced the presence of lymphocyte antigen 6 family member G-positive neutrophils and terminal deoxynucleotidyl transferase dUTP nick end labeling-positive apoptotic cells. PS-OMe miR130 emerges as a potent safeguard against HS-induced lung injury by effectively inhibiting pro-inflammation and injuries, offering a promising therapeutic strategy in such critical clinical condition.

Construction of a Triboelectrochemical Setup with Controlled Environment for Biomaterial Testing with a Comparison of Cobalt–Chromium–Molybdenum and Titanium–Aluminium–Niobium Alloys

The present work is focused on the manufacturing of a special self‐developed tribocorrosion setup with a controlled incubated environment. The comparative studies between wrought Co27Cr6Mo and Ti6Al7Nb alloys are performed with the respective tribometer in Ringer's solution at 37 °C. It is found that the CoCrMo alloy demonstrated a noble open circuit potential not only in non‐wear condition but also under wear conditions, in comparison to Ti6Al7Nb. The mass loss rate examined at open circuit potential and at a constant potential of 0.2 V versus Ag|AgCl|3.5 m KCl also suggests a similar superiority of the CoCrMo alloy.

CLI: A new protocol for the isolation of Lactic Acid Bacteria from complex plant samples

Lactic Acid Bacteria (LAB) are predominantly probiotic microorganisms and the most are Generally Recognized As Safe (GRAS). LAB inhabit in the human gut ecosystem and are largely found in fermented foods and silage. In the last decades, LAB have also has been found in plant microbiota as a new class of microbes with probiotic activity to plants. For this reason, today the scientific interest in the study and isolation of LAB for agronomic application has increased. However, isolation protocols from complex samples such as plant tissues are scarce and inefficient.In this study, we developed a new protocol (CLI, Complex samples LAB Isolation) which yields purified LAB from plants. The sensitivity of CLI protocol was sufficient to isolate representative microorganisms of LAB genera (i.e. Leuconostoc, Lactococcus and Enterococcus).CLI protocol consists on five steps: i) sample preparation and pre-incubation in 1% sterile peptone at 30 °C for 24–48 h; ii) Sample homogenization in vortex by 10 min; iii) sample serial dilution in quarter-strength Ringer solution, iv) incubation in MRS agar plates with 0.2% of sorbic acid, with 1% of CaCO3, O2 < 15%, at pH 5.8 and 37 °C for 48 h.; v) Selection of single colonies with LAB morphology and CaCO3-solubilization halo. Our scientific contribution is that CLI protocol could be used for several complex samples and represents a useful method for further studies involving native LAB.

Electrochemical investigations of PLA coatings deposited by fused filament fabrication on magnesium alloy in Ringer's solution

In this paper, polylactic acid (PLA) layers were printed on AM60 magnesium alloy through a fused filament fabrication-3D printing manufacturing method, as a low-cost and innovative technology. Then, the effect of coating thickness and anodized layer as a binder on the electrochemical behavior of Mg substrates was investigated in Ringer's solution. Electrochemical impedance spectroscopy, Tafel polarization, and weight loss investigations were performed at various exposure times for 28 days to achieve this purpose. Corroded surfaces were also analyzed through field emission scanning electron microscopy images and Fourier-transform infrared spectroscopy patterns. The obtained results showed that the higher thickness of the layer with a value of 400 µm was not effective in raising the PLA layer impedance without the anodized layer. However, the higher PLA thickness could have a key role in the corrosion rate reduction of PLA layers when printed on the anodized layer. The lowest corrosion rate with a value of 0.3 µA/cm2 was related to the PLA-printed layer with a lower thickness (200 µm) and without an anodized layer. This reduction range in corrosion current density was about 80.2–99.4 % compared to the Mg alloy. The weight loss behavior of PLA layers during a long time of exposure was followed by a logarithmic function. The range of corrosion rate decrease was 9.7–32.2 %. The PLA degradation mechanism was also suggested based on all obtained results.

АНАЛИЗ АССОРТИМЕНТА РАСТВОРИТЕЛЕЙ И РАЗБАВИТЕЛЕЙ ИНЪЕКЦИОННЫХ РАСТВОРОВ ДЛЯ ПЕДИАТРИЧЕСКОЙ ПРАКТИКИ

Introduction. Solvents and diluents for parenteral medicines are widely used in pediatric hospitals and occupy leading positions in terms of the number of packages in purchases. Injectables are prescribed to children in reduced volumes, as compared to adults. In this regard, it is relevant to study the solvents and diluents available for parenteral administration of drugs in terms of packaging types and reduced volumes for use in pediatrics in the domestic pharmaceutical market. Aim of the study is to analyze the available solvents and diluents for parenteral medicines, such as water for injection, isotonic solutions of sodium chloride, Ringer, and Ringer lactate, on the Russian pharmaceutical market and in a multidisciplinary children’s hospital. Material and Methods. Objects of the study were data from the State Register of Medicines of Russia, the requisition slips of Medical Devices and Pharmacy of Tatarstan for medicines shipped from a warehouse to the Republic Clinical Children’s Hospital of the Ministry of Health of the Republic of Tatarstan in 2022, the price lists for medicines of pharmaceutical wholesalers (September 2023), and the data from scientific publications. Results and Discussion. The data obtained indicate that the regional pharmaceutical market has about twice as many options for the supply of medicinal solvents and diluents than in a children’s multidisciplinary hospital, and this allows expanding the range of this group of medicines. It can be assumed that pharmaceutical industrial enterprises do not produce a full range of options for the volume of primary packaging of solvents and diluents registered in the State Register of Medicines. Conclusions. In Russia, reduced volumes (20-30 ml) of 0.9% sodium chloride, 5% glucose, Ringer, and Ringer lactate solutions in vials for intravenous drip administration in pediatric practice are neither registered nor produced. The depth coefficient of the assortment of the studied solvents and diluents for parenteral medicines in relation to the volume of primary packaging in a children’s multidisciplinary hospital is 0.102. This indicates the need for medical organizations to consider the possibilities of the pharmaceutical market when drawing up applications for the supply of medicines.

Enhancement of physiochemical, mechanical, dielectric and antibacterial properties of 10 wt% PVA-Ag/Mg/Zn doped hydroxyapatite

Paper describes the doping of hydroxyapatite (HAp) with three different metal ions Mg2+, Ag+ and Zn2+ for enhancing the biocompatibility of HAp. Samples morphology reveals an increase in grain size and the presence of rod-like structures. Tri dopants cause the crystallite size and cell volume to decrease. The sample was found to become harder. Rate of corrosion improved by 14 % as studied in the Ringer's solution. The dielectric studies confirmed that the samples were conducting in nature due to the presence of PVA in the sample. Lesser number of pores was observed for the composite sample which implied improved hardness of those samples. Clotting behaviour decreased after doping due to the increased conducting behaviour after the doping. To test the antibacterial activity, two strains of the bacteria E. coli and S. aureus were used. 10 wt% PVA-Ag/Mg/Zn-HAp demonstrated higher efficacy against both the strains of the bacteria.