Rhodamine B Dye Research Articles

An efficient novel NiCu@INA/rGO MOF hollow microsphere Z-scheme heterojunction catalyst for the photocatalytic degradation of tetracycline and simultaneous degradation of cationic and anionic Dyes

Bimetallic metal-organic framework materials have captivated considerable attention in photocatalysis because of their colossal properties like semiconducting, large surface area, and potent visible light harnessing ability. Self-aggregation and rapid recombination rates have greatly hindered their applications in photocatalysis. A novel reduced graphene oxide-incorporated bimetallic nickel copper metal-organic framework (NiCu@INA/rGO MOF) is fabricated using isonicotinic acid as an organic linker. A synergistic effect between the two metals increased the photocatalytic performance. Introducing reduced graphene oxide to nickel-copper MOF increased charge carrier retention transfer and enhanced the catalyst’s water dispersibility. The efficiency of the photocatalyst for the removal of tetracycline (TCn) and a mixture of Rhodamine B (RhB) and Orange G (OrG) dyes was investigated under visible light. A degradation efficiency of up to 89 % for TCn and close to ∼97.8 % and 93.5 % degradation in the case of RhB and OrG dyes was observed. The studies on the photocatalytic degradation mechanism were explored by conducting radical scavenger experiments, Electron spin resonance (ESR) studies, and Mott-Schottky analysis. TCn and RhB degradation pathways were explored by mass spectral analysis of the intermediates during the photocatalytic degradation of TCn and RhB. This work provides new paradigms for the functional modification of MOF for designing efficient photocatalysis.

Development of a novel lightweight brick-activated carbon based BiVO4 photocatalyst and its adsorption-photocatalytic behavior for toxic dye removal in wastewater

The purpose of this research was to develop a novel photocatalyst by loading BiVO4 (BVO) particles on lightweight brick-activated carbon (LWB-AC). The characterizations of as-prepare samples were studied using X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV–VIS –NIR spectrophotometer (UV-VIS-NIR) techniques. The adsorption-photocatalytic methylene blue (MB) removal, methyl orange (MO) removal and rhodamine B (RhB) removal of the as-prepared LWB-AC based BVO photocatalyst were tested by irradiating visible light. The results showed that the LWB-AC based BVO photocatalyst exhibited the highest adsorption-photocatalytic efficiency for the removal of MB, MO and RhB dyes under visible light irradiation as compared to the other samples. This might be due to the synergistic effect between AC and BVO on the surface of LWB. Moreover, the presence of both AC and BVO on the surface of LWB helped in preventing the electron-hole recombination, resulting in the enhanced adsorption-photocatalytic activity. For reusability tests, the LWB-AC based BVO photocatalyst did not show the loss of adsorption-photodegradation ability of MB, MO and RhB dyes after five runs. A probable adsorption-photodegradation mechanism of LWB-AC based BVO photocatalyst was also proposed.

Nanostructured hexagonal S-doped CeO2 for effective Rh-B and MB dye degradation

The photocatalytic efficiency of CeO2−xSx (x = 0.05, 0.1, 0.2, 0.3, 0.5) hexagonal nanoparticles (HNPs) prepared through the hydrothermal method were tested by performing the degradation of Rhodamine-B and Methylene blue dyes under UV light irradiation. These compounds were thoroughly characterised using XRD, FESEM, EDX, HRTEM, XPS, ESR, FTIR, Raman, UV–vis DRS, BET and PL techniques. XRD analysis verified the cubic crystal structure of S-doped and pure CeO2 HNPs. HRTEM images clearly affirmed that S-doped CeO2 is made from HNPs. Over 94 % of Rh-B and 72 % of MB dyes were degraded by S-doped CeO2 for 180 min under UV light exposure, demonstrating its efficacy towards the photocatalytic activity (PCA). S-doped CeO2 HNPs have enhanced the PCA due to the reduction in the recombination rate of photo-generated electron-hole pairs, the rise in oxygen vacancy (Ov) and the narrowed optical band-gap. The photoluminescence findings clearly validated the increased PCA of S-doped CeO2. The scavenger tests confirmed the OH• and •O2− radicals participation in the quick degradation of both Rh-B and MB dyes.

Phytofiltration of Rhodamine-B dye using microwave-assisted tartaric acid-treated Trapa natans peels from waste water by biosorption

Phytofiltration of Rhodamine-B dye using microwave-assisted tartaric acid-treated Trapa natans peels from waste water by biosorption

Hydrothermal synthesis of BCQD@g-C3N4 nanocomposites supporting environmental sustainability: Organic dye removal and bacterial inactivation

Various studies are being carried out on the removal of organic dyes and the production of antibacterial agents. In this study, boron-doped carbon quantum dot (BCQD) was synthesized by hydrothermal method, and BCQD@g-C3N4 nanocomposite structure was synthesized using graphitic carbon nitride (g-C3N4) as the support material. The photocatalytic activity of the synthesized nanocomposite against MO, RhB dyes, and Escherichia coli (E. coli) bacteria was investigated. The surface, morphology, molecular, and crystal properties of BCQD@g-C3N4 were investigated using characterization methods such as Transmission electron microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), Fluorescence (FL) spectrophotometer, and X-ray diffraction (XRD). As a result of TEM analysis, it was determined that the average particle size of BCQD was 5.1 ± 1.14 nm and showed a homogeneous distribution on 2D g-C3N4. In the XRD spectrum for BCQDs, the diffraction peak corresponding to the (002) amorphous carbon phase was observed at 21.65° In the PL spectrum of B-CQD@g-C3N4s, the emission value was observed at 458 nm. In the study conducted by taking advantage of the photocatalytic feature of BCQD@g-C3N4 nanocomposite, Rhodamine B (RhB) and Methyl orange (MO) were degraded by 65.58 % and 73.56 %, respectively, at the end of 120 min. Additionally, BCQD@g-C3N4 photocatalyst completely inhibited the growth of E. coli bacteria, which are frequently encountered in wastewater, at 90 minutes under sunlight. Escherichia coli (E. coli), which is frequently encountered in wastewater, BCQD@g-C3N4 completely prevented bacterial growth in the 90th minute under sunlight.

Preparation of ZIF-67 derived Co3O4 composite non-homogeneous catalysts with cerium oxide for the efficient degradation of Rhodamine B

The textile printing and dyeing industry produces a significant amount of wastewater, which is challenging to degrade due to its high organic concentration, complex composition, and high chromaticity. This type of wastewater is considered one of the most difficult to treat. In recent years, advanced catalytic oxidation based on sulfate radicals (SO4−) can efficiently degrade printing and dyeing wastewater. Seeking non-homogeneous catalysts for the activation of the radicals is the key problem to be solved nowadays. In this study, Ce/Co-ZIF precursor was obtained by stirring and precipitation, and the ZIF-67-derived non-homogeneous catalyst of Co3O4 and CeO2 was successfully synthesised by calcination for the efficient catalytic degradation of Rhodamine B (RhB) dye. The morphological structure and elemental distribution of the non-homogeneous catalysts were observed using SEM, TEM, XRD, and XPS. Additionally, the factors that affect the degradation of RhB dye were investigated. These factors were adjusted individually, from CeO₂ loading, pH, material dosing, to persulfate (PS) dosing, and it was determined that the rate of RhB degradation also increased from the initial 92 % to a value of 97.1 %. It was found that under the optimal conditions of a CeO2 loading percentage of 0.44, pH of 7, and composite material and potassium persulfate dosage of 5 mg and 0.4 g/L, respectively, the catalytic system achieved a degradation rate of 97.5 % of RhB dye within 30 min. Then the non-homogeneous catalyst could still maintain the good catalytic degradation effect after 5 cycles of regeneration experiments. Therefore, the ZIF-Co3O4@CeO2 non-homogeneous catalyst has a good potential for wastewater treatment and provides a new way for the application of high performance catalysts in the future.

Application of ANN and RSM for Rhodamine B and Safranine-O Decolorization on Zinc-Carbon Battery Waste Derived Ag/CoFe-LDH/rGO Catalyst.

The present work is first aimed at recovering graphite from carbon rods of waste zinc-carbon (Zn-C) batteries for applications such as wastewater treatment, in order to contribute to the development of a sustainable environment. Then, a composite material, cobalt-iron layered double hydroxide combination with reduced graphene oxide, and with subsequent Ag nanoparticles deposition via NaBH4 reduction method (Ag/CoFe-LDH/rGO) was prepared for the catalytic activity of Rhodamine B (RhB) and Safranine-O (SO) as model contaminants from aquatic media. The catalytic activity of RhB and SO by Ag/CoFe-LDH/rGO in the presence of NaBH4 was studied to model and optimize the process parameters (NaBH4 amount, reaction time, initial dye concentration (Co), and catalyst dosage) via central composite design (CCD)-response surface methodology (RSM). Also, an artificial neural network (ANN) model was developed to estimate the catalytic activity of each dye using an RSM data set. The catalytic activities of 99.54% and 99.96% were obtained for RhB and SO dyes, respectively, under the optimal conditions: NaBH4 amount 12.32 mM, reaction time 3.19 min, Co 33.46 mg/L, and catalyst dosage 1.24 mg/mL for RhB dye; NaBH4 amount 16.76 mM, reaction time 3.06 min, Co 15.10 mg/L, and catalyst dosage 1.46 mg/mL for SO dye. The optimum conditions of process parameters by ANN with gray wolf optimizer (GWO) were in good agreement with the points determined the RSM-CCD. These results demonstrate that RSM and ANN approaches can be applied practically and efficiently to maximize the catalytic activity of RhB and SO by Ag/CoFe-LDH/rGO in the existence of NaBH4. On the other hand, from the kinetic and thermodynamic studies, the positive activation enthalpy, ΔH# and the negative activation entropy, ΔS# values for each dye demonstrated that the catalytic performance was endothermic and less random at the solid/liquid interface.

Facile construction of ZnWO4/g-C3N4 heterojunction for the improved photocatalytic degradation of MB, RhB and mixed dyes

This study presents the construction of binary ZnWO4/g-C3N4 nanocomposite via a facile hydrothermal approach to enhance the photocatalytic performance under the visible light irradiation. The proposed ZnWO4/g-C3N4 nanocomposite photocatalyst shows excellent photodegradation towards organic dyes, such as methylene blue (MB) and rhodamine B (RhB). The optimal loading of ZnWO4 and g-C3N4 leads to the synergistic effect which plays a predominant role in inhibiting the fast electron-hole pairs recombination rate at the interface of ZnWO4/g-C3N4 photocatalyst. The degradation rates of MB and RhB is achieved around 92.9 % and 88.8 % under the visible light irradiation for 120 min. According to our findings, the radical quenching experiments suggested that the ●OH radicals played a positive impact in the photodegradation process. Since, our proposed photocatalyst exhibit superior photocatalytic activity towards the individual MB and RhB degradation. The ZnWO4/g-C3N4 photocatalyst were further applied to demonstrate the degradation of mixed dyes (MB and RhB) at an irradiation time of 180 min. In the mixed dye solution, the ZnWO4/g-C3N4 photocatalyst achieved a highest reaction rate of 0.010 min−1 for MB and 0.012 min−1 for RhB with the degradation rate of 87.8 % and 83.3 % for RhB and MB, respectively. For the mixed dyes, the radical quenching experiments confirmed that the ●OH radicals are responsible for the fast photodegradation. Additionally, the practicality of the proposed ZnWO4/g-C3N4 photocatalyst towards the degradation of MB, RhB and the mixed dyes were examined in the tap water samples. Furthermore, the plausible photodegradation mechanism of ZnWO4/g-C3N4 photocatalyst was proposed in detail. This study provides a new insight for the simultaneous degradation of mixed chemical pollutants using our proposed ZnWO4/g-C3N4 photocatalyst.

Simple precipitation synthesis and solar light-driven photocatalytic degradation of Ag3PO4 floating photocatalysts

Abstract A highly efficient and stable photocatalyst, Ag3PO4, was prepared using a simple co-precipitation method at room temperature. The precursors used in this process were AgNO3 and K2HPO4. The resulting Ag3PO4 photocatalyst forms irregularly-shaped spheres with diameters ranging from 300 to 1 μm. The shape of the Ag3PO4 photocatalyst slightly changes when different surfactants (PVA, PVP, PEG) are used. The powdered Ag3PO4 photocatalyst exhibits excellent visible light-driven photocatalytic performance. It is capable of decomposing rhodamine B (RhB) as a model pollutant in just 5 min under visible light irradiation. This performance is quite remarkable. Interestingly, Ag3PO4 floating composite sheets have been achieved using polystyrene (PS) and fumed silica Aerosil 200. After three cycles, the decolorization of RhB dyes remains at 87% with the 30% Ag3PO4@PS/Aerosil 200 sheet. This indicates that the Ag3PO4@PS/Aerosil 200 photocatalyst is highly reusable and stable.

A highly efficient Co-based catalyst for peroxymonosulfate activation for rapid degradation of RhB over a wide pH range

Cobalt-based materials have been demonstrated to be effective heterogeneous catalysts for peroxymonosulfate activation in degrading many refractory organic pollutants. In this study, a new cobalt-based catalyst was prepared using cobalt chloride hexahydrate (CoCl2·6H2O) as the Co2+ source, 2,3-pyrazine dicarboxylic acid and 3,6-DI-4-pyridyl-1,2,4,5-tetrazine (4-PYTZ) as ligands. This catalyst was employed as a peroxymonosulfate activator for the degradation of Rhodamine B(RhB). The results indicated that the prepared Co-based catalyst can effectively degrade RhB dye in aqueous solution by activating peroxymonosulfate (PMS). Specifically, when the initial concentration of RhB was 20 mg/L, its degradation rate exceeded 98 % within merely 9 min. The factors influencing the activation of PMS by the Co-based catalyst were examined, including PMS concentration, reaction temperature, solution pH, and the concentration of organic pollutants. Stability and reusability tests demonstrated that the prepared catalyst exhibited good stability, with the degradation rate of RhB remaining above 97 % after four repetitive experiments. Free radical quenching experiments and electron paramagnetic resonance (EPR) analyses revealed that sulfate radicals (SO4−) and hydroxyl radicals (OH) are the primary reactive radicals accountable for the degradation process. Additionally, it displayed excellent adaptability over a wide pH range, particularly within the pH levels ranging from 5 to 9. This study demonstrates that the prepared Co-based catalyst can serve as a stable and effective option for degrading organic dyes in wastewater treatment applications.

Infiltrated electroless deposition of gold nanoparticles on porous Prussian blue-Fe2O3 hetero-microstructures for environmental remediation applications: A novel infiltration strategy to form 3-D nano-catalytic networks

Metal and metal oxide nanocomposites are promising candidates for heterogeneous catalytic applications. In this regard, most of the metal oxide inner core volume remains as a dead volume, not participating in the catalysis, only the metal/metal oxide hetero-junctions available at the surfaces are involved in the catalysis. Herein, we report a novel strategy for the infiltration of gold nanoparticles into the inner core of 3D-porous Prussian blue/Fe2O3 hetero-microstructures (PBFHM-Au) beyond its outer surface to form an advanced heterogeneous catalyst for the environmental remediation applications. The porosity of the Prussian blue microstructures is thermally tuned for the infiltration of gold ion precursor into the inner core volume of Prussian blue/Fe2O3 hetero-microstructures to facilitate the galvanic displacement reaction between Fe and Au to enlarge the lattice shell and form Au nanoparticle 3D networks throughout the PBFHM. Notably, the resulting PBFHM-Au2 shows enhanced structural stability electron transfer kinetics and catalytic activity in comparison with the only surface-attached Au/Fe2O3 composite. The obtained PBFHM-Au2 catalyst demonstrates remarkable catalytic activity for Rhodamine-B dye degradation with rate constant (k = 3.47 × 10−2 s−1) and p-nitrophenol reduction reactions with rate constant (k = 1.199 × 10−1 s−1).

New recyclable and functionalized chitosan-based polyurethane foams for effective and incessant removal of Orange II (OII) and Rhodamine B (RhB) dyes from water

The development of new efficient materials for the removal of water-soluble toxic organic dyes has been one of the focused research areas in the recent past. There is a strong demand for the new materials as most of the reported techniques/materials suffer from serious limitations. In this regard, a series of flexible chitosan-based task-specific polyurethane foams (PUCS-GP, PUCS-CA-GP, PUCS-TA-GP, and PUCS-GA-GP) associated with naturally available hydroxycarboxylic acids was developed. The basis for the preparation of these task-specific and functionalized PU foams is to possess amine groups for trapping the anionic dyes (example: Orange II denoted as OII) and carboxylic acid groups for attracting the cationic dyes (example: Rhodamine B denoted as RhB) under specified pH conditions. Batch adsorption experiments were conducted to assess and improve various parametric conditions. The experimental results revealed that the adsorption kinetics closely agree with the pseudo-second-order model having a maximum sorption capacity of 38.3 mg/g at pH 3 for OII on PUCS-GP and 48.4 mg/g at pH 6 for RhB on PUCS-CA-GP. Furthermore, the adsorption process was described by isotherms, kinetic equations and thermodynamic parameters (ΔG°, ΔH° and ΔS°). Notably, the regeneration of OII and RhB dyes from the exhausted PUCS-GP and PUCS-CA-GP materials was effectively accomplished. The recovered PUCS-GP shows >90 % OII and PUCS-CA-GP displays >70 % RhB removal efficiency even after twelve adsorption–desorption processes under mild conditions, demonstrating excellent recyclability/durability. The advantages of these functionalized foam materials are facile preparation, high adsorption capacity, good reusability, and very efficient removal of organic dyes from wastewater streams.

Exploring structural and optical properties of iodine-doped TiO2 nanoparticles in Rhodamine-B dye degradation: Experimental and theoretical investigation

Energy conversion and pollutant degradation are critical for advancing sustainable technologies, yet they often encounter challenges related to charge recombination and efficiency limitations. This study explores iodine-doped TiO2 nanoparticles as a potential solution for enhancing both energy conversion and pollutant degradation. The nanoparticles were synthesized via the sol-gel method with varying iodine precursor concentrations (0.025–0.1 M) and were characterized for their structural, compositional, and optical properties, particularly in relation to their photocatalytic performance in Rhodamine-B dye degradation. X-ray diffraction confirmed a tetragonal anatase crystal structure, with the average crystallite size decreasing from 10.06 nm to 8.82 nm with increase in iodine concentration. Selected area electron diffraction patterns verified the polycrystalline nature of the nanoparticles. Dynamic light scattering analysis showed hydrodynamic radii ranging from 95 to 125 nm. Fourier-transform infrared spectroscopy identified metal-oxygen vibrations at 441 cm⁻1, and electron microscopy confirmed the spherical morphology of the nanoparticles. Elemental analysis detected the presence of Ti, O, and I in the samples. Diffuse reflectance spectroscopy indicated the optical absorption edges for the doped samples in the visible region from which the corresponding band gap values were deduced. Photoluminescence spectroscopy revealed that the sample with 0.1 M iodine exhibit the lowest emission intensity, suggesting reduced charge recombination. Notably, 0.1 M iodine doped TiO2 samples demonstrated the highest photocatalytic efficiency, achieving 82.36% degradation of Rhodamine-B dye within 140 min under visible light. Additionally, ab-initio density functional theory calculations were performed to investigate the structural, optical, and adsorption properties of TiO2, iodine-doped TiO2, Rhodamine-B, and their composites, providing further insight into the enhanced photocatalytic activity observed in the experiments.

Removal of Rhodamine-B dye from Aqueous Solutions Using Alkaline-Modified Activated Carbon from Cocoa Pod Husk.

Rhodamine-B (RhB) dye in wastewater poses health and environmental risks due to respiratory and eye infections, neurotoxicity, and carcinogenicity, necessitating proper disposal for risk mitigation. This study investigates RhB removal from water using NaOH-modified activated carbon derived from cocoa pod husk (CPHAC). Employing a face-centered central composite design, operational variables were optimized to achieve maximum RhB dye removal efficiency. The study reveals a removal efficiency of 98.87 ± 0.84% under optimized conditions: adsorbent dose of 1.34g, contact time of 71.59min, and an initial RhB concentration of 6.61 ppm. The Freundlich isotherm model demonstrated a good fit, suggesting that RhB removal is governed by heterogeneity and multilayer adsorption. Kinetic experiments revealed that adsorption follows a pseudo-second-order model, indicating likely irreversible adsorption with dye molecules forming chemical bonds on CPHAC's surface. Overall, this study demonstrates the effectiveness of CPHAC as an efficient adsorbent for RhB removal from water.

A highly efficient and stable PtNi bimetallic nanoparticles modified on Mo2C decorated N-doped carbon flowers catalysts for the remediation of environmental pollutants

The unregulated discharge of nitroaromatics (NAs) and organic dye contaminants into aquatic ecosystems is a growing global concern, highlighting the urgent need for the development of effective wastewater treatment technology. In this study, we prepared Mo2C decorated on N- doped carbon flowers supported with PtNi bimetallic (PtxNiy@Mo2C/NCF) nanoparticles using the self-polymerization of dopamine and followed by the chemical reduction methods. These catalysts, with varying Pt:Ni ratios, were designed for the highly efficient catalytic reduction of NAs and rhodamine b (RhB) under the mild reaction conditions. The HR-TEM images confirmed the formation of spherical PtNi bimetallic NPs with an average diameter of 1.68 ± 0.6 nm. The prepared PtxNiy@Mo2C/NCF catalysts exhibited significantly higher catalytic efficiency for 4-nitrophenol (4-NP) reduction compared to their respective monometallic counterparts using NaBH4. Particularly, the Pt0.75Ni0.25@Mo2C/NCF catalyst showed superior catalytic activity with the apparent rate constant (kapp: 0.6703 min−1) and TOF (17.0 × 10−7 mol mg−1 min−1) and high recyclability over eight consecutive recycles. Furthermore, the Pt0.75Ni0.25@Mo2C/NCF catalyst also exhibited high catalytic activity for other NAs and RhB dye reduction with excellent yields. This enhanced catalytic activity of Pt0.75Ni0.25@Mo2C/NCF catalyst could be ascribed to the synergistic effect of the bimetallic systems, leading to more efficient reactions. Additional experiments were conducted on a fixed bed reactor to demonstrate that the Pt0.75Ni0.25@Mo2C/NCF catalyst effectively reduce both 4-NP and RhB dye over 15 successive runs. This work may pave the way for using PtxNiy@Mo2C/NCF catalysts in various wastewater treatment applications.

Photocatalytic degradation of rhodamine B dye pollutants by Fe3O4/SiO2 core-shell magnetic nanocomposite functionalized with TiO2.

Significant efforts have been dedicated to creating recyclable and efficient methods for treating waste dyes, including rhodamine B (RhB). Nevertheless, challenges such as complex operational techniques, high costs, energy consumption, and inefficacy in dye removal persist. Here, the synthesis and application of TiO2/Fe3O4/SiO2 for photocatalytic degradation of RhB dye pollutants have been explored. This research was initiated with magnetite (Fe3O4) synthesis using the coprecipitation method, followed by silica (SiO2) extraction from rice husk waste using the sol-gel process, and a hydrothermal method for synthesizing titanium dioxide (TiO2) and TiO2/Fe3O4/SiO2 nanocomposite. The crystalline structure of TiO2/Fe3O4/SiO2 was obtained with Fe3O4 as the core, while TiO2 and SiO2 as the shell. The particle size analysis showed the nanosize of TiO2/Fe3O4/SiO2 (1.04 ± 0.46nm). TiO2/Fe3O4/SiO2 nanocomposite boasts a high surface area of 48.025 m2/g, 2.2 times higher than unmodified TiO2. This nanocomposite also displayed paramagnetic properties with a saturation magnetization of 9.117emu/g, facilitating easy separation in photocatalytic applications. The photocatalytic activity of TiO2/Fe3O4/SiO2 exhibited effectively degraded RhB, achieving a degradation rate of 53.58% and an excellent rate constant of 0.7303min-1. The RhB photodegradation in this study requires a moderate irradiation time (60min), uses only a tiny amount of photocatalyst (100mg), and does not need additional chemicals. Moreover, this study has another advantage of utilizing rice husk as a silica source, offering an eco-friendly and sustainable approach.

(Ce, Nd) co-doped TiO2 NPs via hydrothermal route:Structural, optical, photocatalytic and thermal behavior

Rare earth (Ce, Nd) doped/co-doped titania (TiO2) nanoparticles were successfully produced by hydrothermal route. Titanium isopropoxide (IV), cerium nitrate hexahydrate and neodymium nitrate hexahydrate were utilized as raw/starting materials. The effect of Ce and Nd doping/co-doping in TiO2 were studied through different complementary tools such as XRD, FTIR, FE-SEM, EDX, XPS, UV–Visible, PL, photocatalytic and thermal analysis. XRD spectra revealed anatase tetragonal phase and cubic phase due to titania and ceria nanoparticles respectively. The crystallite size, lattice constants, volume and no. of unit cell were determined through XRD data. Optical studies revealed the band gap, urbach energy, extinction coefficient, refractive index, optical conductivity and photoluminescence emission wavelength. FTIR spectra investigated the chemical bondings and functional groups present in prepared samples. Optical absorption spectra confirmed that absorption edge is red shifted, indicating a decrease in band gap from 3.5 to 3.0 eV with the incorporation of rare earth ions (Ce, Nd) in TiO2 matrix. The rate of electron-hole pair recombination was reduced through co-doping of (Ce, Nd) in TiO2 lattice as exhibited by reduction in intensity of photo luminescence spectra. The photocatalytic efficiency was enhanced with the integration of rare earth metal ions in TiO2 matrix for different dyes such as rhodamine B (RhB) and malachite green (MG) with visible light irradiation. The degradation efficiency of (Ce, Nd) co-doped TiO2 NPs against RhB and MG dyes was found to be 89 and 95 % respectively. TGA analysis was carried out to find weight loss during different thermodynamic phases such as dehydration, decomposition and combustion, and crystallization. Various thermodynamic parameters such as activation energy, entropy and enthalpy were estimated by thermal analysis.

Plant-based synthesis of Selenium-doped Silver/Magnesium Oxide/Zinc Oxide nanocomposite using Mentha pulegium to investigate their photocatalytic and biological properties

In this study, the photocatalytic test and biological effects of Selenium-doped Silver/ Magnesium Oxide/ Zinc Oxide nanocomposite (Se-doped Ag/MgO/ZnO) have been studied. The samples were synthesized by a green method with Mentha pulegium plant extract and investigated by different analyses. The outcomes of X-ray and FESEM display crystal nature and flower-like morphology. According to the ICP results, the removal efficiency of Pb+2 ions was equal to 72 %. The photocatalytic test of the nanocomposite investigated to degradation of organic dyes, and the results show that the degradation percentage of RhB (Rhodamine B), EBT (Eriochrome Black T), MO (Methyl Orange), and MB (Methylene Blue) dyes were about 73 %, 96 %, 99 %, and 97 % respectively. Also, the toxicity of the Se-doped Ag/MgO/ZnO) was studied against the cancer B16F0 cell line and the IC50 value was reported as 269.6 μg/mL.

Facile fabrication of carbon nanotubes/zinc oxide decorated poly(vinyl alcohol) electrospun nanofiber membrane and its photocatalytic performance

AbstractThe carbon nanotubes/zinc oxide (CNTs/ZnO) nanocomposites were immobilized on the poly(vinyl alcohol) (PVA) membrane for highly reutilization rate in photocatalytic degradation of RhodamineB (RhB) based on the combination of electrospinning and ultrasonication treatment. The results revealed that the CNTs are successfully compounded with ZnO, and the surface of nanofibers was uniformly covered with CNTs/ZnO nanoparticles. Under visible light irradiation, the CNTs/ZnO@PVA nanocomposites displayed excellent photocatalytic activity with 98.4% of RhB degradation rate within 3 h illumination. In comparison with pure PVA, and CNTs/ZnO with equivalent loading capacity on CNTs/ZnO@PVA film suspended in aqueous solution, the synthesized CNTs/ZnO@PVA film degrades RhB dye more efficiently. Furthermore, the photocatalytic activity of CNTs/ZnO@PVA nanocomposites did not change significantly even after five recycles, indicating a certain degree of reusability. The mechanism of enhanced photocatalytic activity was proposed. The as‐prepared flexible CNTs/ZnO@PVA nanocomposites could be employed as a promising material for the practical photocatalytic degradation of wastewater.

Ag nanoparticle functionalized vertical WS2 nanoflakes as SERS substrate for chemical sensing

Two-dimensional transition metal dichalcogenides (TMDCs) present a unique opportunity as Surface Enhanced Raman Scattering (SERS) substrates due to their superior optical properties. Here, vertically oriented tungsten disulfide (WS₂) flakes were synthesized on a silicon (Si) substrate using the pulsed laser deposition (PLD) technique. The WS₂ flakes were employed as SERS substrates for detecting low concentrations of environmental pollutants, like Rhodamine B (RhB) and Methyl Orange (MO) dyes, achieving promising enhancement factors of approximately 10⁷ with a 532 nm excitation laser. To further enhance the plasmonic activity of the vertical WS₂ flakes, silver nanoparticles (NPs) were decorated on their surface via thermal evaporation. The Ag NP-functionalized WS₂ flakes exhibited superior detection capabilities compared to pristine WS₂ flakes, achieving remarkable sensitivity at ultralow concentrations of 10⁻¹⁶ M for RhB and 10–17 M for MO dye, with enhancement factors of the order of 10⁸. The SERS performance of the WS₂-Ag substrate was also evaluated using a 633 nm laser, successfully detecting Methylene Blue (MB) dye at an ultralow concentration of 10⁻¹³ M. Prolonged exposure to RhB, MO, and MB dyes can cause cancer, neurotoxicity, and respiratory irritation. Thus, sensitive detection of these dyes at ultralow concentrations is highly crucial. A charge transfer mechanism between WS₂ and RhB dye molecules is proposed, along with the contribution of Ag NPs, to explain the enhanced detection capabilities of the nanocomposite SERS substrate.