Frequency Rf Research Articles

Study of process parameters and characteristics properties of W coatings deposited by rf plasma sputtering

Tungsten coatings were deposited on silicon substrates by radio frequency (rf) magnetron sputtering from a metallic target in Ar atmosphere. The process parameters during the sputtering process were evaluated by a Langmuir probe, particularly, the electron density and electron temperature were measured by changing the rf power and gas pressure. The morphological and structural properties of the coatings were studied as a function of the pressure. Significant correlations were found between process parameters and characteristics properties of W coatings. The influence of deposition parameters on electrical properties was investigated. The electrical resistivity of the coatings was increased from 1.3 × 10−6 to 3 × 10−5 Ω m as the pressure increased as well.

High-resistivity with PN interface passivation in 22 nm FD-SOI technology for low-loss passives at RF and millimeter-wave frequencies

In this paper, GlobalFoundries’ 22 nm fully depleted (FD) silicon-on-insulator (SOI) process is run on standard and high-resistivity wafers with a specially designed PN junctions interface passivation solution to counteract parasitic surface conduction (PSC) effects. Substrate quality is evaluated at RF and mm-wave frequencies through the on-wafer measurements of a set of passives: coplanar waveguides (CPW) lines, two inductors and a crosstalk structure. The effective resistivity (ρeff), losses and harmonics generated by the substrate are monitored based on CPW lines measurements, fabricated in either bottom or top metal layers. Several PN patterns are examined and they demonstrate effective passivation of the PSC, enabling ρeff values in the kΩ.cm range (up to ∼6 GHz) and > 100 Ω.cm up to ∼60 GHz. Patterns with intrinsic region separating the P- and N- doping regions show better performance, which can further be improved applying a reverse PN bias to widen the depletion regions. 50 Ω CPW line designed with PN interface passivation achieves 0.22 dB/mm lower propagation losses at 50 GHz than 50 Ω thin-film microstrip line in this technology. Impact of substrate quality on two spiral inductors is analyzed by comparing substrates with standard resistivity, high-resistivity with PSC and high-resistivity with PN junction solution. The high-resistivity substrate with PN junction solution shows an up to 62% and 15% increase in quality factor with respect to the standard substrates for the 5–20 GHz and 30–60 GHz inductors, respectively. Finally, measurements of a crosstalk structure show a strong isolation improvement in crosstalk through the substrate with the PN interface passivation solution.

ICRF heating schemes for the HL-2M tokamak

The HL-2M tokamak is a new medium-sized tokamak at SouthWestern Institute of Physics. Two of its key missions are to achieve 10 keV ion temperature and investigate the behavior of energetic particles relevant to burning plasmas. A 6 MW ion cyclotron range of frequencies (ICRF) heating power is embedded in the next upgrade program of HL-2M. In order to facilitate the engineering design of the ICRF system, this paper analyses the main ICRF heating schemes for HL-2M, in terms of ion heating and energetic ion generation in particular. D(H) minority heating and the 2nd harmonic D will act as the main ion heating schemes, for which the optimal RF frequency range 27–33 MHz, antenna parallel wavenumber k // ∼ 8 m−1 are proposed and strong single pass absorption is expected under typical HL-2M plasma parameters. Full wave simulations carried out via TORIC/steady-state Fokker–Planck quasilinear solver and TRANSP codes suggest that by adopting three ion scheme or synergetic heating on neutral beam injection D ions by the 2nd harmonic D, energetic ions with energy at MeV level can be produced. This study shows that ICRF heating could play significant roles in ion heating, energetic ion generation in HL-2M.

Overview of CW electron guns and LCLS-II RF gun performance

Various continuous-wave (CW) electron gun technologies are reviewed, including DC, superconducting radio frequency RF (SRF), hybrid DC-SRF and normal-conducting RF. Also, the SLAC Linac Coherent Light Source II (LCLS-II) normal-conducting RF gun and injector are described, and the performance to date, including the bunch emittance achieved and the dark current observed, is presented.

Photonics-Assisted Analog Wideband Self-Interference Cancellation for In-Band Full-Duplex MIMO Systems With Adaptive Digital Amplitude and Delay Pre-Matching

A photonics-assisted analog wideband RF self-interference (SI) cancellation and frequency downconversion approach for in-band full-duplex (IBFD) multiple-input multiple-output (MIMO) systems with adaptive digital amplitude and delay pre-matching is proposed based on a dual-parallel Mach–Zehnder modulator (DP-MZM). In each MIMO receiving antenna, the received signal, including different SI signals from different transmitting antennas and the signal of interest, is applied to one arm of the upper dual-drive Mach–Zehnder modulator (DD-MZM) of the DP-MZM, the reference signal is applied to the other arm of the upper DD-MZM, and the local oscillator signal is applied to one arm of the lower DD-MZM. The SI signals are canceled in the optical domain in the upper DD-MZM and the frequency downconversion is achieved after photodetection. To cancel the SI signals, the analog reference signal is constructed in the digital domain, while the amplitude and delay of the constructed reference are adjusted digitally by upsampling with high accuracy. Experiments are performed when two different SI signals are employed. The genetic algorithm or least squares algorithm is combined with segmented search respectively for the SI signal reconstruction and amplitude and delay pre-matching. A cancellation depth of around 20 dB is achieved for the 1-Gbaud 16 quadrature-amplitude modulation orthogonal frequency-division multiplexing signal.

Development of a linear ion trap mass spectrometer capable of analyzing megadalton MALDI ions

Detecting megadalton matrix-assisted laser desorption/ionization (MALDI) ions in an ion trap mass spectrometer is a technical challenge. In this study, megadalton protein and polymer ions were successfully measured by MALDI linear ion trap mass spectrometer (LIT-MS) for the first time. The LIT-MS is comprised of a Thermo linear ion trap mass analyzer and a highly sensitive charge-sensing particle detector (CSPD). A newly designed radio frequency (rf) scan mode with dipolar resonance ejection techniques is proposed to extend the mass range of LIT-MS up to one million Thomson (Th). We analyze high mass ions with mass-to charge (m/z) ratios ranging from 100 kTh to 1 MTh, including thyroglobulin, alpha-2-macroglobulin, immunoglobulins (e.g., IgG and IgM), and polymer (∼ 940 kTh) ions. Besides, it is also very challenging for ion trap mass spectrometry to detect megadalton ions at low concentrations. By adopting high affinity carboxylated/oxidized detonation nanodiamonds (oxDNDs) to enrich IgM molecules and form antibody-nanodiamond conjugates, we have successfully reached ∼ 5 nM (5 μg/mL) concentration which is better than that by the other techniques.

Frequency Switchable Global RFID Tag Antennae with Metal Compatibility for Worldwide Vehicle Transportation.

This paper presents an effective way to design an RFID tag antenna to operate at three different frequencies by incorporating a switching technique. PIN diode has been used to switch the RF frequency because of its good efficiency and simplicity. The conventional dipole-based RFID tag has been improvised with added co-planar ground and PIN diode. The layout of the antenna is designed with a size of 0.083 λ0 × 0.094 λ0 at UHF (80-960) MHz, where λ0 is the free-space wavelength corresponding to the mid-point of the targeted UHF range. The RFID microchip is connected to the modified ground and dipole structures. Bending and meandering techniques on the dipole length help to match the complex chip impedance with the dipole impedance. Additionally, it scales down the total structure of the antenna. Two PIN diodes are placed along the dipole length at appropriate distances with proper biasing. The ON-OFF switching states of the PIN diodes enable the RFID tag antenna to switch over the frequency ranges (840-845) MHz (India), 902-928 MHz (North America), and 950-955 MHz (Japan).

RF design and frequency sensitivity analysis of a 1500 MHz passive third harmonic superconducting cavity for the SILF

To reduce Touschek scattering in the beam and extend the lifetime of the beam in the Shenzhen Innovation Light-source Facility (a fourth-generation light source), a 1500 MHz passive third harmonic system will be used. The present work is devoted to the RF design and frequency sensitivity analysis of the 1500 MHz passive third harmonic superconducting cavity, optimizing the RF parameters of the cavity, and giving a frequency scheme for the cavity in fabrication. The reliability of the cavity during operation is taken as the main goal for the optimization of the geometrical parameters, and its structural and RF parameters are obtained with E peak/E acc of 2.17, B peak/E acc of 5.12 mT/(MV/m) and G · R/Q of 25052 at 2 K. A pair of fluted beam pipes are used to propagate the higher order modes (HOMs) of the harmonic cavity, allowing a smooth transition of the first dipole mode to the absorber located at room temperature area. For the frequency sensitivity analysis, the frequency variations of the cavity in fabrication are obtained by multi-physics coupling simulation in the paper, which gives the target frequency of the cavity between welding and preloading. After electron beam welding (EBW), the resonant frequency of the cavity should be maintained at 1500.096 MHz, and the pre-tuning target frequency is 1497.456 MHz. The slow tuning range is ±400 kHz, the fast-tuning range is 600 Hz, and the maximum allowable tuning force is 15 kN.

Improvement of the magnon-magnon coupling strength in Y3Fe5O12/Py heterostructures

Magnon-quasiparticle couplings perform magnon information transferences and transports, thus controlling the coupling strengths is significant for novel information function devices. Here, we report the modulation of the magnon-magnon (M−M) coupling strength in Y3Fe5O12/permalloy (YIG/Py) heterostructures via ferromagnetic resonance (FMR) technique. The anti-crossing gap gc enhances 80 Hz by changing the radio frequency (rf) microwave power, which could be ascribed to the enhancement of the dipolar interaction and spin pumping effect. Furthermore, the gc decreases with the increasing angle θ between external magnetic field and rf current due to the increase of magnon relaxation. Moreover, the FMR linewidths change with increasing angle θ due to the magnetic anisotropy parameters and the two-magnon relaxation mechanism induced by the more oblique external field.

Technical note: Measurement of the bunch structure of a clinical proton beam using a SiPM coupled to a plastic scintillator with an optical fiber.

Recent proposals of high dose rate plans in protontherapy as well as very short proton bunches may pose problems to current beam monitor systems. There is an increasing demand for real-time proton beam monitoring with high temporal resolution, extended dynamic range and radiation hardness. Plastic scintillators coupled to optical fiber sensors have great potential in this context to become a practical solution towards clinical implementation. In this work, we evaluate the capabilities of a very compact fast plastic scintillator with an optical fiber readout by a SiPM and electronics sensor which has been used to provide information on the time structure at the nanosecond level of a clinical proton beam. A 3×3×3mm3 plastic scintillator (EJ-232Q Eljen Technology) coupled to a 3×3mm2 SiPM (MicroFJ-SMA-30035, Onsemi) has been characterized with a 70 MeV clinical proton beam accelerated in a Proteus One synchrocyclotron. The signal was read out by a high sampling rate oscilloscope (5 GS/s). By exposing the sensor directly to the proton beam, the time beam profile of individual spots was recorded. Measurements of detector signal have been obtained with a time sampling period of 0.8 ns. Proton bunch period (16 ns), spot (10 μs) and interspot (1 ms) time structures could be observed in the time profile of the detector signal amplitude. From this, the RF frequency of the accelerator has been extracted, which is found to be 64 MHz. The proposed system was able to measure the fine time structure of a clinical proton accelerator online and with ns time resolution.

The effects of Ar + N2 plasma power-based attachment of metal nanoparticles on the electron field emission properties of carbon nanotubes

An ideal vacuum-based electron emitter requires a low turn-on field and quick emission processes. Carbon nanotubes (CNTs) have great potential for emission applications, but have some limitations that affect their performance. Consequently, they can benefit from the alteration of their surface morphology upon decoration with plasma-based metal nanoparticles. In this work, we have attached iron nanoparticles on the CNTs surface via a radio frequency (rf) sputtering process using Ar + N2 gas with various plasma power in steps of 50 W. Field emission scanning electron microscopy (FESEM) micrographs have confirmed the attachment of the iron nanoparticles and etching of the nanotubes surface at high plasma power. The Raman spectra strongly confirm the formation of defects in the carbon sheet of the nanotubes. In the plasma treatment process, the increase in the Dband intensity enhanced the degree of disorder and may be beneficial for enhanced emission properties. The field electron emission properties are significantly enhanced after the Fe nanoparticles attached with plasma incorporated in terms of the reduction in Eto (1.64 from 2.02 V/μm) &Eth (1.98 from 2.64 V/μm), and increase in J (391.11–1179.24 μA/cm2) and β (1419–2900), respectively. The field emission parameters of the field emitters are modified due to incorporation of nitrogen species, attached Fe nanoparticles, and reduction in the nanotube density. The as-prepared field emitters also qualified the orthodox field emission hypothesis test by exhibiting fextr values in an acceptable range. Therefore, we can use the Ar + N2 plasma-based Fe nanoparticles decorated CNT field emitters in vacuum electronic device applications.

Correcting aberrations of a transverse-field neutron resonance spin echo instrument.

Neutron resonance spin echo (NRSE) technique has the potential to increase the Fourier time and energy resolution in neutron scattering by using radio frequency (rf) neutron spin-flippers. However, aberrations arising from variations in the neutron path length between the rf flippers reduce the polarization. Here, we develop and test a transverse static-field magnet, a series of which are placed between the rf flippers, to correct for these aberrations. The prototype correction magnet was both simulated in an NRSE beamline using McStas, a Monte Carlo neutron ray-tracing software package, and measured using neutrons. The results from the prototype demonstrate that this static-field design corrects for transverse-field NRSE aberrations.

Smart Vehicle: A Systematic Review

This article gives a summary of the existing state of affairs and potential developments for smart vehicles while taking into consideration social, technological, and transportation aspects. Additionally, it examines the strategies for turning the smart into a generic vehicle, potential future developments, 5G, ADAS, and power source characteristics. This will make it possible for linked automobiles to take center stage in smart cities. Information may be exchanged between vehicles and road infrastructures as well as from one vehicle to another thanks to the vehicle-to-infrastructure (V2I) and vehicle-to-vehicle (V2V) communication systems. It attempts to improve mobility, prevent or lessen auto accidents, and offer additional advantages for road safety. Motivations, open problems, and suggestions from other academics were taken into account to improve the knowledge of many contextual components and characteristics of the industry. All publications about data transfers in the V2I communication system were thoroughly searched. They employ DSRC and 5G, Bluetooth, and WIFI technology in that, however there is a range and data transmission rate issue. I exploited RF frequencies to spontaneously broadcast the data in order to get around that.

Analysis of spurious peaks at series resonance in solidly mounted resonators by combined BVD-Mason modelling

Solidly Mounted Resonators (SMRs) for high frequency RF filters and sensing applications often display spurious resonances that distort their frequency response. In this work, we try to identify the origin of spurious resonances accompanying the main series resonances in AlN-based SMRs with the help of modified Butterworth Van Dyke (BVD) and Mason’s models. By manufacturing SMRs of different sizes and shapes and studying the influence of the position of the electrical probing spot, we have demonstrated both theoretically and experimentally that devices with larger areas are more likely to display these additional peaks. Our updated models accurately simulate the frequency response of the SMRs, revealing that spurious peaks are mostly related to the resistance of the electrodes. Our study clarifies the origin of the spurious resonances and offers solutions for both, the optimal design and measurement method of SMRs.

Virtual-carrier-assisted 12 Gb/s 64QAM millimeter-wave signal transmission at 30 GHz using a 4-bit digital-to-analog converter.

We propose and experimentally demonstrate a radio-frequency digital resolution enhancer (RF-DRE) to mitigate the quantization noise of the RF signal induced by the low-resolution digital-to-analog converter (DAC) in the virtual-carrier-assisted millimeter-wave (mm-wave) signal transmission system. By introducing a bandpass filter (BPF) as the reference for the RF-DRE algorithm, we can design the quantization noise and shape its spectrum inversely to the bandpass filter. By these means, the quantization noise in the target RF frequency range can be effectively mitigated. In the simulation, the bit error rate (BER) of a 4-bit DAC-quantized 16 Gb/s 256QAM signal at 30 GHz is improved from 3.36e-2 to 7.43e-3 by using the RF-DRE. In our experiment, 30 GHz virtual-carrier-assisted mm-wave transmission of 12 Gb/s 64QAM signals over 25 km of standard signal mode fiber (SSMF) is realized. By using the RF-DRE, the BER of a 4-bit DAC-quantized signal can be improved from 6.88e-3 to 1.49e-3, and a 5-bit DAC exhibits a similar performance to an 8-bit DAC without the RF-DRE. Therefore, low-resolution and low-cost DACs can be used for mm-wave signal generation with the help of the proposed RF-DRE.

Buried RF Sensors for Smart Road Infrastructure: Empirical Communication Range Testing, Propagation by Line of Sight, Diffraction and Reflection Model and Technology Comparison for 868 MHz-2.4 GHz.

Updating the road infrastructure requires the potential mass adoption of the road studs currently used in car detection, speed monitoring, and path marking. Road studs commonly include RF transceivers connecting the buried sensors to an offsite base station for centralized data management. Since traffic monitoring experiments through buried sensors are resource expensive and difficult, the literature detailing it is insufficient and inaccessible due to various strategic reasons. Moreover, as the main RF frequencies adopted for stud communication are either 868/915 MHz or 2.4 GHz, the radio coverage differs, and it is not readily predictable due to the low-power communication in the near proximity of the ground. This work delivers a reference study on low-power RF communication ranging for the two above frequencies up to 60 m. The experimental setup employs successive measurements and repositioning of a base station at three different heights of 0.5, 1 and 1.5 m, and is accompanied by an extensive theoretical analysis of propagation, including line of sight, diffraction, and wall reflection. Enhancing the tutorial value of this work, a correlation analysis using Pearson's coefficient and root mean square error is performed between the field test and simulation results.

Dynamics Inside a Dual-Frequency Paul Trap in the Presence of Excess Micromotion

Dynamics inside a dual-frequency Paul trap is theoretically analyzed in the presence of excess micromotion on account of stray electric field and the field due to a mismatch of potential at the electrodes. The fields contributing to the excess micromotion have a strong influence on the kinetic energy of a single-charged particle, however, their influence is not profound when the collective dynamics of many charged particles is considered inside the trap. The collective dynamics is encapsulated by a distribution function whose time average is double-humped with respect to the velocity. The spatial variation of energyis asymmetrical. The temporal fluctuations of the energy are periodic with a period of variation depending upon the ratio of the two applied RF frequencies.

Satellite-transition double cross-polarization HETCOR under fast MAS

Double-cross polarization to the satellite-transitions (STs) of half-integer quadrupolar nuclei is demonstrated using proton-detected heteronuclear correlation (HETCOR) under fast magic-angle spinning (MAS). By placing the rf frequency away from the central-transition (CT) and selective to the STs, average Hamiltonian theory shows a scaled effective rf field with a phase equal to the complex ST spinning sideband being irradiated. Such an effective rf field can excite and spinlock STs but the phase spread usually leads to signal cancellation in one-step excitation or cross polarization experiments. The cancellation does not occur for two-step double cross-polarization (DCP) HETCOR experiments, therefore high efficiencies can be obtained. With careful magic-angle calibration, ST and double-quantum ST (DQST) HETCOR experiments are demonstrated with the 35Cl nuclei in histidine·HCl·H2O. These experiments provide additional information over the commonly observed CT spectra and near isotropic resolution in the case of DQST of spin S = 3/2 quadrupolar nuclei.

Spill ripple mitigation by bunched beam extraction with high frequency synchrotron motion

Slow extraction of bunched beams is widely used for mitigating the formation of temporal microstructures on the extracted beam due to ripples of the accelerator magnets power supplies. That helps in experiments with slow detectors or measurements with low event rates. Additionally, in ion cancer therapy machines, this technique is widely used for avoiding long gaps in the spill measured in ionization chambers which in turn would trigger interlocks. It is also well known that extraction of a bunched beam creates spill structures on time scales defined by the rf frequency which limits its usability for faster detectors. In this report, we show that further macroscopic spill structures of duration up to some hundred milliseconds can be created during bunched beam extraction for a sufficiently large synchrotron tune. The aim of this work is to study the influence of the synchrotron tune and its interplay with slow extraction settings on the slow extraction quality. Further dependencies on transverse emittance and longitudinal bunch area of the circulating beam are discussed.

Remote Control of Electrical Home Appliances Using RF Module based Remote

This study examines the use of an RF-based remote system to manage domestic electrical appliances. The wireless remote control based on an RF technology can toggle the status of equipment to ON or OFF from any site without necessitating a line of sight anywhere around house. The regulating circuit is developed around a 434 MHz operational frequency RF receiver and transmitter module, along with the HT12E encoder and HT12D decoder integrated circuits and a few other passive components. The four distinct channels at the encoder end are used as switches for input signal, and the four channels at the decoder end are used as outputs points, which is connected to the respective electrical devices that are to be controlled; if the appliances are of a higher rating, the relays are used as an intermediary to connect the equipment to the receiving end of the circuit. The transmission method used in this instance is Amplitude Shift Keying (ASK), and the circuit is powered with a 9V DC battery source. The main objective of this task entails creating a closed circuit without any programming knowledge and making it functional without the need for line-of-sight utilizing RF technology. Also, as proposed development to the current working model is stated with a brief description of its functioning, which aims to efficiently control more than four electrical units using the same remote-control technology with the aid of a matrix keypad as input for switching the states of the devices, a matrix encoder & decoder for respective encoding & decoding of signals, and a stable multivibrator for circuit operations.