Reversed-phase Liquid Chromatography Column Research Articles

Comparison of ion-pair and amide-based column reversed-phase liquid chromatography for the separation of thiamine-related compounds

Two reversed-phase chromatographic methods for the separation of thiamine and related compounds are compared. The first procedure is based on the ion-pair technique using an octadecylsilica column, while the second uses a new amide-based stationary phase, which avoids the need to form ion-pairs, leading to narrower peaks and a simpler mobile phase. Analyses were performed by gradient elution and a photo-diode array was used for detection. Specificity was demonstrated by the retention characteristics, UV spectra and by comparing the peak purity index with commercial standards. The procedures were applied to the determination of thiamine-related compounds in pharmaceutical preparations and urine. No preliminary sample treatment was required.

Repeatability and reproducibility of retention data and band profiles on reversed-phase liquid chromatography columns: V. Results obtained with Vydac 218TP C 18 columns

The general goal of this work is to investigate the precision of chromatographic data and to determine which properties of chromatographic columns influence this factor. Chromatographic data were acquired under five different sets of experimental conditions for 30 neutral, acidic and basic test compounds on columns packed with Vydac 218TP C 18, a polymeric, wide-pore silica-based stationary phase. Five columns packed with samples from the same batch of this packing material were used to measure the column-to-column reproducibility and six columns packed with material from six different batches to measure the batch-to-batch reproducibility. The parameters studied were the retention time, the retention and separation factors, the hydrophobic and the steric selectivities, the column efficiency, and the tailing factor.

Proteomics of glycoproteins based on affinity selection of glycopeptides from tryptic digests

Identification of glycoproteins in complex mixtures derived from either human blood serum or a cancer cell line was achieved in a process involving the steps of (1) reduction and alkylation, (2) proteolysis of all proteins in the mixture with trypsin, (3) affinity chromatographic selection of the glycopeptides with an immobilized lectin, (4) direct transfer of the glycopeptide fraction to a reversed-phase liquid chromatography (RPLC) column and further fractionation by gradient elution, (5) matrix-assisted laser desorption ionization mass spectrometry of individual fractions collected from the RPLC column, and (6) peptide identification based on a database search. The types of glycoproteins analyzed were; (1) N-type glycoproteins of known primary structure, (2) N-type glycoproteins of unknown structure, and (3) O-type glycoproteins glycosylated with a single N-acetylglucosamine. Identification of peptides from complex mixtures was greatly facilitated by either C-terminal sequencing with a carboxypeptidase mixture or by comparing chromatographic behavior and mass to standards, as in the case of a known protein. In addition, deglycosylation of peptides with N glycosidase F was necessary to identify N-type glycoproteins of unknown structure. The strength of this approach is that it is fast and targets specific molecular species or classes of glycoproteins for identification. The weakness is that it does not discriminate between glycoforms.

Quantitative Proteomic Analysis Using a MALDI Quadrupole Time-of-Flight Mass Spectrometer

We describe an approach to the quantitative analysis of complex protein mixtures using a MALDI quadrupole time-of-flight (MALDI QqTOF) mass spectrometer and isotope coded affinity tag reagents (Gygi, S. P.; et al. Nat. Biotechnol. 1999, 17, 994-9.). Proteins in mixtures are first labeled on cysteinyl residues using an isotope coded affinity tag reagent, the proteins are enzymatically digested, and the labeled peptides are purified using a multidimensional separation procedure, with the last step being the elution of the labeled peptides from a microcapillary reversed-phase liquid chromatography column directly onto a MALDI sample target. After addition of matrix, the sample spots are analyzed using a MALDI QqTOF mass spectrometer, by first obtaining a mass spectrum of the peptides in each sample spot in order to quantify the ratio of abundance of pairs of isotopically tagged peptides, followed by tandem mass spectrometric analysis to ascertain the sequence of selected peptides for protein identification. The effectiveness of this approach is demonstrated in the quantification and identification of peptides from a control mixture of proteins of known relative concentrations and also in the comparative analysis of protein expression in Saccharomyces cerevisiae grown on two different carbon sources.

On‐line solvent evaporator for coupled normal phase‐reversed phase high‐performance liquid chromatography systems: Heavy polycyclic aromatic hydrocarbons analysis

AbstractAn on‐line system for coupling a normal phase liquid chromatography (LC) column to a reversed‐phase LC column is described. The interface consists of an on‐line solvent evaporator working on the principles of concurrent eluent evaporation and vapor overflow, and two additional 10 port valves. Optimization of the on‐line procedure as well as recoveries, repeatability and linearity characteristics were tested in a simplified system simulating determination of heavy polycyclic aromatic hydrocarbons in edible oils. An application on a real extra virgin olive oil sample is also reported. © 2001 John Wiley & Sons, Inc. J Micro Sep 13: 13–18, 2001

Determination of retinoids in galenicals by column liquid chromatography with fluorescence and diode-array detection

Simple and rapid reversed-phase gradient column liquid chromatography (LC) with fluorescence detection at different wavelengths was developed for the simultaneous analysis of all- trans, 13- cis, 9- cis retinoic acids, vitamin A palmitate and β-carotene in galenicals. The assay results agreed with those obtained by an LC method with diode-array UV detection. A post-column on-line photochemical reactor (irradiation at 254 and 366 nm) was inserted between the LC column and the fluorescence detector to enhance the performance of the method. Two fluorescence spectra (photoreactor on and off) were obtained for each analyte which proved useful for the unambiguous identification of the various analytes.

Determination of cis and trans isomers of monocrotophos in technical products by reversed-phase column liquid chromatography

A simple reversed-phase column liquid chromatographic method for the determination of cis and trans isomers of monocrotophos (MCP) using a C 18 column, aqueous acetonitrile as eluent and UV detection at 218 nm was developed. The method was used for quality assurance and to study the relative stabilities of cis and trans isomers in technical products of MCP.

Liquid Chromatographic Method with Immunoaffinity Column Cleanup for Determination of Ochratoxin A in Barley: Collaborative Study

A collaborative study was conducted to evaluate a liquid chromatographic (LC) method with immunoaffinity column cleanup for determination of ochratoxin A. The method was tested at 3 concentration levels of ochratoxin A in barley, which represent possible future European regulatory limits. The test portion was extracted with acetonitrile-water by blending at high speed. The extract was filtered, diluted with phosphate-buffered saline (PBS), and applied to an ochratoxin A immunoaffinity column. The column was washed with water and the ochratoxin A eluted with methanol. The solvent was then evaporated and the residue redissolved in injection solvent. After injection of this solution onto reversed-phase LC column, ochratoxin A was measured by fluorescence detection. Eight samples of low level naturally contaminated barley and 2 samples of blank barley (ochratoxin A not found at the limit of detection of 0.2 microg/kg at the signal-to-noise ratio of 3 to 1) were sent, along with ampules of ochratoxin A, calibrant, and spiking solutions, to 15 laboratories in 13 different European countries. Test portions were spiked with ochratoxin A at levels of 4 ng/g, and recoveries ranged from 65 to 113%. Based on results for spiked samples (blind duplicates) and naturally contaminated samples (blind duplicates at 3 levels), the relative standard deviation for repeatability (RSDr) ranged from 4 to 24%, and the relative standard deviation for reproducibility (RSDR) ranged from 12 to 33%. The method showed acceptable within- and between-laboratory precision, as evidenced by HORRAT values, at the low level of determination for ochratoxin A in barley.

Surface-enhanced resonance Raman spectroscopy as an identification tool in column liquid chromatography.

The compatibility of ion-pair reversed-phase column liquid chromatography and surface-enhanced resonance Raman spectroscopy (SERRS) for separation and identification of anionic dyes has been investigated, with emphasis on the at-line coupling via a thin-layer chromatography (TLC) plate. SERR spectra using silver sols were recorded both for aqueous solutions and for samples deposited on aluminum oxide and silica TLC plates at 514.5- and 457.9-nm laser excitation. For some dyes, the shorter wavelength was needed to diminish the fluorescence background. For aqueous solutions and for samples deposited on aluminum oxide, clear SERR spectra were obtained upon addition of poly(L-lysine); for the silica plates, the addition of nitric acid was required. Upon drying the plates, the SERRS signals decreased in intensity; simply adding a drop of water could largely restore them. At-line coupling of LC and SERRS was successfully achieved when using silica, but not aluminum oxide, plates. The application of a gradient, a high water content, and the presence of ion-pair reagents needed for the separation did not adversely affect the deposition and the recording of SERR spectra. The identification limits were 10-20 ng of deposited material, depending on the dye selected, which corresponded to injected concentrations of 5-10 microg mL(-1).

Selectivity differences for C 18 and C 8 reversed-phase columns as a function of temperature and gradient steepness : I. Optimizing selectivity and resolution

Four experimental runs where temperature T and gradient time t G are varied allow the computer-prediction of reversed-phase liquid chromatographic (RPLC) separation for different combinations of temperature and gradient time. This in turn can provide significant changes in selectivity and a resulting optimization of separation. If this procedure is repeated for different columns, additional control over selectivity and resolution becomes possible. The simultaneous variation of T and t G for columns from different sources was studied for two samples, as a means of evaluating the general advantage of this approach for RPLC method development. Changes in relative retention with T were found to be approximately constant for different values of t G and for different RPLC columns; similarly, changes in relative retention with t G were roughly independent of changes in temperature or the column. The latter relationships can be useful in matching (“tracking”) peaks between runs during method development based on the present approach, as well as for other applications discussed in here and in Part II.

Reversed-phase capillary liquid chromatography coupled on-line to capillary electrophoresis immunoassays.

Capillary reversed-phase liquid chromatography (RPLC) was coupled on-line to competitive capillary electrophoresis immunoassay (CEIA) to improve concentration sensitivity of the competitive CEIA and to provide a means for detecting multiple species that cross-react with antibody. A competitive CEIA for glucagon was used for demonstration of this technique. Five-microliter samples were injected onto a 4-cm-long by 50-micron-i.d. RPLC column. Sample was desorbed by gradient elution, mixed on-line with fluorescently labeled glucagon and anti-glucagon, incubated in a continuous-flow reaction capillary, and analyzed by capillary electrophoresis with flow-gated injection and laser-induced fluorescence detection. Electrophoretic analysis of the reactor stream was performed every 1.5 s, allowing nearly continuous monitoring of the RPLC separation. Preconcentration achieved by RPLC allowed improvement in the detection limit from 760 to 20 pM. Addition of the RPLC column also allowed multiple cross-reactive species to be differentiated by first separating them chromatographically and then detecting them with the immunoassay. The technique was used to measure glucagon secretion from single islets of Langerhans and to differentiate cross-reactive forms of glucagon with one assay.

Determination of Carbendazim in Water, Soil and Sediment Samples by RPLC with and Without Column Switching and Various Spectrometric Detection Modes

This study presents the developed and applied methods for the determination of carbendazim in environmental samples originating from several field studies. For water samples sample pretreatment consisted of a solid phase extraction (SPE) on cartridges packed with 200 mg SDB-1. In case of solid samples the performance of microwave assisted solvent extraction (MASE) and classical ultrasonic extraction with acetone-ethyl acetate were studied. The latter technique was selected because of the reduced time of manual operations. Instrumental analysis of extracts of water samples was performed on-line with coupled column reversed phase liquid chromatography (LC/LC) and UV detection (280 nm) allowing to assay carbendazim to a level of at least 0.1 μg/l. Improved column life time was obtained by performing the favorable LC separation of carbendazim at high pH on newly developed 5 μm Extend-pH bidentate C18 material. The combination of a short column packed with 5 μm Inertsil ODS-5 and a mobile phase at low pH material was most adequate as the regards the robust and fast processing of extracts of solid samples and allowed in most cases the screening of carbendazim in soils and sediments to a level of 10μg/kg. The developed procedures yield overall recoveries for carbendazim of 101, 80 and 71 % in water (levels, 0.1—1.2 μg/l: n=12), soil (levels, 10 and 100 μg/kg; n=22) and sediments (levels, 10 and 100 μg/kg; n=11), respectively, with a repeatability and reproducibility below 7 % for all method/matrix combinations. Soil samples with aged residues (level, 100 μg/kg; n=10) provided an overall recovery of 71% and no significant decrease of carbendazim was observed during nine weeks of storage in the refrigerator.

Determination of Sulfamethazine in Swine and Cattle Feed by Reversed-Phase Liquid Chromatography with Post-Column Derivatization: Collaborative Study

A liquid chromatographic (LC) method for the analysis of sulfamethazine (SMT) in complete swine and cattle feed was collaboratively studied. The method uses post-column derivatization with dimethylaminobenzaldehyde and detection at 450 nm. To 5g finely ground feed, extractant (0.2N HCl + 1.5% diethylamine in 25% methanol), and internal standard solutions are added, and the SMT is extracted by shaking for 1 h. Clarified extract (high-level sample extract diluted to a target concentration of ca 5.5 microg/mL) is chromatographed on a Cla reversed-phase LC column with acetonitrile-2% acetic acid (17 + 83) mobile phase. Sulfamerazine is used as an internal, or surrogate standard to correct for variable recovery of sulfamethazine from a variety of feed matrixes. Six Youden matched-pair samples were sent to 10 collaborators in Korea, Canada, and the United States. Label claims on the commercial feeds ranged from 0.0077 to 0.22% SMT. The SMT mean recovery as determined from the 5 samples with known analyte content was 99.8%. The within-laboratory relative standard deviation (repeatability) ranged from 0.28 to 4.72%. Among-laboratory (including within-laboratory) relative standard deviation (reproducibility) ranged from 1.26 to 4.87%. The authors recommend the method for AOAC INTERNATIONAL Official First Action status.

Repeatability and reproducibility of retention data and band profiles on reversed-phase liquid chromatography columns: IV. Results obtained with Luna C 18 (2) columns

The reproducibility of retention data and band profile characteristics was investigated for a series of columns packed with Luna C 18 (2), a silica-based, reversed-phase adsorbent. High precision data were obtained and statistically compared among five columns from the same batch (column-to-column reproducibility) and nine columns from as many different batches (batch-to-batch reproducibility). These data were acquired under five different sets of chromatographic conditions, for a group of 30 neutral, acidic, and basic compounds selected as probes following an experimental protocol previously described. This work is part of a study on the precision of chromatographic analyses. Its purpose is to illustrate the contribution of the stationary phase reproducibility to this precision.

Reversed-phase liquid chromatographic column switching for the determination of N-methylcarbamates and some of their main metabolites in urine

A column switching system for the determination of some polar pesticides and their main metabolites, such as aldicarb, aldicarb sulphoxide, aldicarb sulphone, carbofuran and 3-hydroxicarbofuran, in human urine has been developed. The limits of detection were between 0.3 and 1 μg/l. We used a simple solid-phase extraction with graphite carbon and a RPLC–LC analysis with UV detection yielding average recoveries between 84 and 110% ( N=5) with RSD between 4 and 8%.

Chemiluminescence determination of catecholamines in human blood plasma using 1,2-bis(3-chlorophenyl)ethylenediamine as pre-column derivatizing reagent for liquid chromatography

A highly sensitive method for the determination of the human blood plasma catecholamines (norepinephrine, epinephrine and dopamine) is described which employs liquid chromatography (LC) with chemiluminescence detection. Solid-phase extraction using cation exchange cartridges was used for selective and quantitative isolation of the catecholamines and isoproterenol (an internal standard) from 20 μl of human plasma containing 0.1 pmol ml −1 isoproterenol. The amines and isoproterenol, derivatized with 1,2-bis(3-chlorophenyl)ethylene diamine, were separated on a reversed-phase LC column with isocratic elution using a mixture of imidazole buffer (120 mM, pH 5.8), methanol, acetonitrile (13 : 4 : 18, v/v/v). The eluate was detected by a post-column chemiluminescence reaction system using bis[4-nitro-2-(3,6,9-trioxadecyloxycarbonyl)phenyl]oxalate and hydrogen peroxide. The detection limits (a signal-to-noise ratio = 3) for each catecholamine are 40–120 amol in a 100 μl injection volume.

Analysis of taxol and major taxoids in Himalayan yew, Taxus wallichiana

A reversed-phase column liquid chromatography method for the analysis of taxol, 10-deacetylbaccatin III, baccatin IV, 1-hydroxybaccatin I, 2-acetoxybrevifoliol, brevifoliol, 2′-deacetoxydecinnamoyltaxinine J and 2′-deacetoxytaxinine J in yew needles has been developed using a Nova-Pak Phenyl column and a binary gradient profile. The various aspects of analysis such as extraction efficiency, detection limits, reproducibility and peak purity were validated using UV–Vis as well as photodiode array detection.

Repeatability and reproducibility of retention data and band profiles on reversed-phase liquid chromatography columns: III. Results obtained with Kromasil C 18 columns

The reproducibility of the retention data and the band profiles was investigated with Kromasil C 18 columns (silica-based monomeric type reversed-phase packing material). High precision data were obtained and statistically compared among five columns from the same batch (column-to-column reproducibility) and six columns, one from each of six different batches (batch-to-batch reproducibility). These data were acquired under five different sets of chromatographic conditions, for a group of 30 neutral, acidic and basic compounds selected as probes following an experimental protocol previously described. Data characterizing the retention time, the retention factor, the separation factor, the column efficiency and the peak asymmetry for the different probe compounds are reported. Factors describing the silica surface interaction with the selected probe compounds, such as the hydrophobic interaction selectivity, the steric selectivity, and the separation factors of basic compounds at different pH values were also determined. The influence of the underlying silica on these data and correlations between the chromatographic and physico–chemical properties of the different batches are discussed.

Rapid, direct determination of polyphenols in tea by reversed-phase column liquid chromatography

Column liquid chromatography on a C 18-bonded silica column with water–methanol–acetic acid as eluent was used to determine polyphenols and caffeine in tea. Without any pretreatment, catechin, epicatechin gallate, epigallocatechin gallate, epigallocatechin, epicatechin and caffeine were separated successfully within 15 min. The detection limits ( S/N=3) of polyphenols studied were 1.8–24 mg/l at a detection wavelength 270 nm. The linear range of the peak area calibration curves for the analytes were over two orders of magnitude with a correlation coefficient of 0.996–0.999. Using this method, some Chinese tea samples were analyzed with a good reproducibility (RSD are below 5%).

Monitoring aged reversed-phase high performance liquid chromatography columns

In this paper, a new approach for the quality assessment of routinely used reversed-phase high performance liquid chromatography columns is presented. A used column is not directly considered deteriorated when changes in retention occur. If attention is paid to the type and magnitude of the changes, columns often can still be used. Therefore, columns have to be monitored at regular time points. This means that, in the first place, a few well chosen measurements have to be done on the used column. With statistical techniques, Hotelling's T 2 statistic in combination with three-way analysis, the type and magnitude of changes in retention then can be detected. The type of changes can be divided in hydrophobicity changes, selectivity changes and both hydrophobicity and selectivity changes. This paper describes the approach in theory, completed with examples. At the end, a strategy for monitoring during routine use is proposed, which is visualized in a monitoring scheme.