Microplastic Retention Research Articles

Microplastic removal in conventional drinking water treatment processes: Performance, mechanism, and potential risk

The effectiveness of traditional drinking water treatment plants for the removal of Microplastics (MPs) in the size range of tens of micrometers is currently uncertain. This study investigated the behavior and removal efficiency of four different sized polystyrene MPs (10−90 μm in diameter) in a simulated cascade of coagulation/sedimentation, sand filtration, and UV-based oxidation over technically relevant time frames. In the coagulation and sand filtration steps, the larger the MP size, the better it was removed. The coagulant type and water characteristics (i.e., pH and the presence of natural organic matter) influenced the coagulation efficiency for MPs. X-ray microcomputed tomography technique and two-site kinetic modeling were used to identify the mechanisms involved in sand filtration. The MPs > 20 μm could be completely retained in sand by straining, while the attachment to the sand surface was likely responsible for the retention of MPs < 20 μm. However, approximately 16% of 10 μm MPs injected passed through the sand, which were further fragmented by UV oxidation. UV/H2O2 treatment promoted the MP fragmentation and chemical leaching more significantly than UV treatment, resulting in a higher toxicity for UV/H2O2-treated water. Our findings pave the way for deeper understanding of how MPs behave and transform in a sequential drinking water treatment process.

Release of microplastic particles to the aquatic environment via wastewater treatment plants: The impact of sand filters as tertiary treatment

Monitoring of microplastics (MP) release into the aquatic environment is an important topic and proposed point sources for microplastics are wastewater treatment plants (WWTPs). Three full-scale WWTPs (A, B, C) were investigated to compare the effect of continuously and discontinuously backwashed sand filters to retain microplastics from secondary treated wastewater effluents. A cascade filtration unit using steel basket filters with mesh sizes of 100 µm, 50 µm and 10 µm was employed for sampling. The subsequent analysis used thermal extraction desorption gas chromatography mass spectrometry (TED-GC–MS). This combined analytical approach offered the benefit of sampling multiple cubic meters of WWTP effluent and using a robust quantification analytical method for microplastic without the need for an additional chemical-based sample preparation step. Due to the different capacities of the three WWTPs, the results were normalized based on population equivalents (P.E.). Four common polymers were targeted in this study (i.e., PE, PS, PP, and PET). PE was the most common polymer detected in secondary effluents, with normalized annual loads ranging between 2.8 mg yr–1P.E.-1 and 8.4 mg yr-1P.E.-1. Results showed that sand filters offered additional efficient MP retention capabilities, with the sand filters offering, on average, an extra 79% ± 11% of MP retention when compared to secondary treatment. Finally, one filter cell with aged and one with restored granular media were compared. The aged cell did not indicate lower retention of microplastic while using granular media that was already in operation for seven years.

Biofilm growth on buoyant microplastics leads to changes in settling rates: Implications for microplastic retention in the Great Lakes

Buoyant microplastic pollution disperses widely from sources via strong wind-driven water currents in lakes and oceans. This ability for dispersal depends critically upon the particle's density, which can change over time due to microbial growth (biofilm). This study quantifies biofilm-induced sinking rates of irregularly-shaped polypropylene granules (~125–2000 μm) via ex-situ experiments emulating a Great Lakes freshwater environment. Biofilm development increases particle density and lowers microplastic rise velocities, eventually causing sinking. We observed sinking for 100% of small and intermediate microplastics, and 95% of large microplastics. Under constant environmental conditions, sinking onset was observed sooner for smaller particles (~125–212 μm, 18 days) than for larger particles (~1000–2000 μm, 50 days). Differences in settling onset would lead to size-fractionation of particle sedimentation, whereby smaller particles are deposited closer to their sources relative to larger particles. Our study demonstrates a novel mechanism by which buoyant microplastics can selectively sink from the lake surface.

Microplastics retention by reeds in freshwater environment

Microplastic pollution has recently gained increasing attention. The accumulation of microplastics in plants has been confirmed in the marine environment. However, the extent of the microplastic retention in freshwater plants is still unknown. In this study, sediment and plant samples from six reed farms in the wetland of East Dongting Lake were collected and analyzed. The abundance of microplastics in the sediment of reed farms varied from 125.7 to 1219.5 items/kg dry weight (dw), with an average of 511.2 ± 295.0 items/kg. Moreover, different levels of microplastic abundance were found in reeds from 0 to 14 items/individual. The abundance of microplastics in sediment samples was moderate compared to that worldwide and higher than that in other regions of Dongting Lake. The microplastic pollution level was significantly higher in the reed vegetation belt than that in other sampling positions. On the basis of the distribution and characteristics of the collected microplastics, lake water and fishery are suggested as important sources of microplastics. Furthermore, the factors influencing microplastic retention in the reeds are discussed. This study, as the first direct evidence demonstrating that freshwater reeds tend to accumulate microplastics, constitutes valuable reference for future research.

From the ocean to jellies forth and back? Microplastics along the commercial life cycle of red algae

Red algae are increasingly exploited for direct consumption and for production of gelling agents like agar and carrageenan, widely employed in food and personal care products. In this article we identify knowledge gaps about microplastics in the whole commercial life cycle of gelling red algae, from their marine production to the final wastewater treatment. Recommendations for new research include studies of microplastics deposition on red algae at sea, during the industrial process of production of gelling agents, and indeed about improvements of microplastics retention in wastewater treatment plants.

Rivers and Wastewater-Treatment Plants as Microplastic Pathways to Eastern Mediterranean Waters: First Records for the Aegean Sea, Greece

The present work provides the first records on microplastic (MP) amounts and types in rivers and wastewater effluents entering the Aegean Sea, eastern Mediterranean. Two rivers were sampled using a manta net (mesh size, 0.33 mm): a small urban and a medium-sized river with a rural, semiurban catchment. MPs in wastewater samples were collected at two wastewater treatment plants (WWTPs) within the Athens metropolitan area after secondary treatment and from a pilot biological membrane unit (MBR), using a series of sieves. MPs in the samples were identified using stereoscopic image analysis and spectroscopic techniques. MP concentrations in the rivers were found to be variable, with as high as 27.73 items m−3 in the urban river. Differences in MP shape types, sizes, and polymer types reflect catchment size and usage. MP concentration in wastewater effluents was found to be 100 times higher in the secondary treatment (213 items m−3) than that in the pilot MBR (2.29 items m−3), with filaments and polymers indicative of synthetic textiles and household use. Further research is needed in order to accurately determine variability in MP concentrations and fluxes from these two pathways in the eastern Mediterranean Sea and elucidate the role of rivers in MP retention.

The influence of weirs on microplastic fate in the riverine environment (case study: Jeneberang River, Makassar City, Indonesia)

The riverine environment is known as the main pathway of microplastic entering the ocean. Recent studies show that the barricading of water flow in the riverine environment can influence the microplastic load to the ocean. The Jeneberang River, which is located in Makassar City, is prone to microplastic pollution. There are three weirs located in this river as water barricades. The aim of this study was to measure the microplastic abundance upstream and downstream of each weir flow. Microplastics in the water compartment were measured using the volume-reduce towing method and were measured in the sediment compartment using a density separator method. The results show that microplastic abundance in the water prior to passing each weir was higher (1.43 – 3.19 item/m3) compared by the flow after each weir (1.20 – 2.10 item/m3). The same pattern was also apparent in the sediment compartment where the microplastic abundance prior to the weirs tended to be higher (28.33 – 56.67 item/kg DW) compared to the compartment after the weir (30.00 – 53.33 item/kg DW). Based on microplastic shape, there is no evidence that weirs in the Jeneberang River are blocking any specific shape of microplastic. In conclusion, weirs that are commonly found in the riverine environment could act as microplastic retention devices in the riverine environment.

The seasonal distribution characteristics of microplastics on bathing beaches along the coast of Qingdao, China

Microplastics pollution in nearshore marine environment has become increasingly prominent and has received widespread attention. As a major leisure and entertainment place in coastal cities, bathing beaches not only provide an environment for microplastics to enter the ocean, but also provide a place for the retention of microplastics. In this paper, the distribution, composition and seasonal variation of microplastics in seawater and sediments of six bathing beaches along the coast of Qingdao were studied. The results showed that the average abundance of microplastics in the sediments of the Qingdao bathing beach was 91.11 ± 26.76 items/m2 (13.77 ± 4.39 items/kg) in the winter and 147.78 ± 34.80 items/m2 (21.98 ± 5.97 items/kg) in the summer. The microplastic abundance in the seawater in the summer (average: 567.50 ± 101.06 items/m3) was significantly higher than that in the winter (average: 326.11 ± 49.03 items/m3, p < 0.05). The abundance of microplastics at the six bathing beaches increased from east to west, consistent with the transport direction of coastal currents. The microplastic abundance in the sediment of non-swimming zone of the bathing beach was significantly higher than that in swimming zone (p < 0.05), and the microplastic abundance in the seawater of the swimming zone was slightly higher than that of the non-swimming zone but with no significant difference (p > 0.05). To an extent, it can reflect the correlation between the abundance of microplastics and human recreational activities. The microplastics detected at the bathing beaches were mainly lines (80.5%) and fragments (7.9%) with a size range of 100 to 1000 μm. Rayon (41.8%) and polyethylene terephthalate (PET, 16.9%) were the main polymer types. The microplastic characteristics showed significant seasonal differences, more diversity in summer than in winter. These results emphasized that the distribution and movement of microplastics in bathing beaches were affected by seasons, human activities and coastal currents.

Combined Approaches to Predict Microplastic Emissions Within an Urbanized Estuary (Warnow, Southwestern Baltic Sea)

Microplastic river emissions are known to be one of the major sources for marine microplastic pollution. Especially urbanized estuaries localized at the land-sea interface and subjected to microplastic emissions from various sources exhibit a high microplastic discharge potential to adjacent coasts. To adapt effective measures against microplastic emissions a more detailed knowledge on the importance of various microplastic sources is necessary. As field data is scarce we combined different approaches to assess microplastic emissions into the Warnow estuary, southwestern Baltic Sea. Resulting microplastic emission estimates are based on in-situ measurements for the catchment emissions, whereas for the remaining microplastic sources within the estuary literature data on microplastic abundances, and various parameters were used (e.g. demographical, hydrological, geographical). The evaluation of the different emission scenarios revealed that the majority of microplastic is likely discharged by the Warnow river catchment (49.4%) and the separated city stormwater system (43.1%) into the estuary, followed by combined sewer discharges (6.1%). Wastewater treatment plant emissions exhibit the lowest percentage (1.4%). Our approach to estimate anti-fouling paint particles emissions from leisure and commercial shipping activities was associated with highest uncertainties. However, our results indicate the importance of this source highlighting the necessity for future research on the topic. Based on our assumptions for microplastic retention within the estuary, we estimate a potential annual emission of 152–291 billion microplastics (majority within the size class 10–100 µm) to the Baltic Sea. Considering all uncertainties of the different applied approaches, we could assess the importance of various microplastic sources which can be used by authorities to prioritize and establish emission reduction measures. Additionally, the study provides parameters for microplastic emission estimates that can be transferred from our model system to other urbanized Baltic estuaries.

The sea cucumber Holothuria tubulosa does not reduce the size of microplastics but enhances their resuspension in the water column

Microplastic pollution is increasingly recognized as a prominent threat to marine life. Understanding the role of bioturbators is crucial to determine to what extent marine sediments can act as a microplastic sink. The presence of microplastics has been documented in holothurians, but no study has investigated how the ingestion-egestion process influences their bioavailability. Using the Mediterranean deposit-feeder, Holothuria tubulosa, as a model system, we assessed if, upon ingestion, plastic particles are accumulated in pseudofeces and if the passage through the digestive tract reduces their size. To this end, the number, shape and colour of plastic particles was compared between pseudofeces and surrounding surficial sediments collected along the edges of a seagrass meadow. Pseudofeces were enriched in plastic fragments with respect to surficial sediments, suggesting a selective ingestion of fragments over fibres. By contrast, there was no difference in the size or colour of plastic particles between pseudofeces and sediments. In addition, by means of a laboratory experiment, we evaluated how microplastic resuspension rates from pseudofeces compares with those from surficial sediments. Under standard water movement conditions, the resuspension of labelled microplastics from pseudofeces was much greater than that from sediments (i.e., about 92% and 26% at the end of the experimental trial). Greater relative abundance of fine material (i.e., pelite) in pseudofeces than sediments could explain their physical instability and, hence, their lower microplastic retention. Our results suggest that pseudofeces of H. tubulosa not only represent a hotspot for plastic fragment concentration, but, due to their surficial deposition and rapid dissolution, they could also promote their transfer to the water column. Ingestion and egestion of microplastics by this sea cucumber, although not altering their size, may thus enhance their bioavailability.

Microplastic ingestion in reared aquaculture fish: Biological responses to low-density polyethylene controlled diets in Sparus aurata.

During the last years, ingestion of microplastics (MPs) has been quantified in marine species both with an ecological and commercial interest at sea and under experimental conditions, highlighting the importance to assess MP ingestion in commercially and aquaculture important species such as gilthead seabream (Sparus aurata) fish. In order to study the ingestion of MPs in a commercially valuable species, gilthead seabreams were exposed to an enriched diet with virgin and weathered low-density polyethylene (LDPE) pellets for three months followed by a detoxification period of one month of no exposure to MP enriched diets. Our results indicate that MP ingestion in these fishes increased with exposure time, and differences were found between treatments, showing the highest ingestion values after three months of exposure to MP enriched diets and in the weathered treatment. However, after one month of detoxification, no MPs were found in the gastrointestinal tracts of fish, reflecting no long-term retention of MPs in Sparus aurata digestive system. According to results from this study, exposure of fish to MP enriched diets does not affect fish size neither the Fulton's condition index as both parameters increased with time in all treatments (control, virgin and weathered). Both carbon and nitrogen isotopic signatures decreased with fish size in all treatments which could be related to an increase of nitrogen deposition efficiency in fish muscle with a high protein assimilation during the first months of Sparus aurata.

Transport and fate of microplastics in constructed wetlands: A microcosm study

Constructed wetlands (CWs) are commonly used for the treatment of wastewater. However, the removal of microplastics in CWs are poorly understood. In this work, the fate and behavior of microplastics of different shapes (film, fragment, and fiber) and sizes (0.5–1 mm and 2–4 mm) were studied. Results showed that the microplastic removal rate was 81.63% in surface flow constructed wetlands (SF-CWs) and 100% in horizontal subsurface flow constructed wetlands (HSF-CWs). Fragments and fibers with 2–4 mm sizes flowed out preferentially from SF-CWs. Retained microplastics accumulated dominantly near the inlet area. Biofilm attachment and physical filtration played an important role in the retention of microplastics. The microplastics’ morphological features and the apertures of the substrate related to the transport of microplastics in the substrate. We observed the formation of holes, cracks, and weeny fibers on the surface of the microplastics extracted from the microcosms with a scanning electron microscope (SEM), but we detected no oxidation based on the Fourier transform infrared spectra. Our results suggest that CWs, especially HSF-CWs, are efficient for the removal of microplastic pollution. However, microplastics are persistent in CWs. The potential impacts of microplastics on the function of CWs should be further assessed.

Assessment of plastic pollution in the Bohai Sea: Abundance, distribution, morphological characteristics and chemical components.

Plastics are globally distributed in oceans and can pose a threat to the environment and organisms. In this study, plastic pollution in surface water and sediments of the Bohai Sea was assessed based on plastic abundance, distribution and characteristics (shape, polymer, size and color). Water and sediment samples were collected across the sea using a plankton net (330μm) and a grab sampler, respectively. The following conclusions were reached. 1) In surface water, large plastics were less abundant (0.14 items/m3) and showed less diverse characteristics than microplastics (0.79 items/m3) but did not significantly differ in spatial distribution. 2) Microplastics in water were more abundant (1.95 items/m3) with more diverse characteristics in Liaodong Bay than in other regions of the sea (0.26-0.59 items/m3). Plastic waste from highly concentrated agricultural, industrial and fishery activities could make large contributions to microplastics in Liaodong Bay. Additionally, low hydrodynamics and long distance to Bohai Strait are unfavorable for diffusion of particles, facilitating the retention of microplastics and increasing the abundance in this bay. 3) Microplastics in sediments were smaller in terms of dominant sizes (<0.5mm) with less diverse characteristics than particles in water (0.5-1.5mm). Specifically, fragments, foams and lines dominated among the microplastics in water, whereas fibers and fragments were dominant particles in sediments; alkyd resin, polyethylene, polystyrene and polypropylene (PP) predominated among the particles in water, but rayon, cellulose and PP were dominant particles in sediments. 4) Neither abundance nor size of microplastics in the two media was proportionally correlated and showed low similarity indexes of polymer (0.16), shape (0.29) or color (0.38). This could be related to mismatch in spatiotemporal distributions and variations in the characteristics, fate and behavior of microplastics in the two media. The findings provide knowledge for tracing the sources of plastics in the Bohai Sea.

Vertical migration of microplastics along soil profile under different crop root systems

Microplastics are highly accumulated in soils and supposed to migrate vertically due to water infiltration, fauna activities, and root growth. In this study, the vertical migration of microplastics along soil profile under three crop roots (corn, soybean, and ryegrass) was analyzed by a laboratory-scale incubation experiment. When microplastics were initially distributed in the surface layer, crop roots showed little effects on the vertical migration of microplastics. But in terms of homogenous microplastic distribution along soil profile, corn roots could contribute to the upward movement of microplastics in the middle layers (7-12cm). It could be related to more pores and fissures created by primary and secondary corn roots and buoyancy effects once the pores and fissures were filled with water. Additionally, a significant positive correlation between microplastic numbers and tertiary roots of ryegrass has been observed and indicated the microplastic retention ability of fine crop roots. According to the results, in contrast to the downward microplastic migration caused by water infiltration and soil fauna activities, crop roots tended to move microplastics upwards or maintain them in soil layers.

Seasonal characteristics of microplastics ingested by copepods in Jiaozhou Bay, the Yellow Sea

Microplastics (MPs) are a growing threat to marine biota and ecosystems, and zooplankton are at high risk of ingesting MPs. The seasonal changes in MPs in zooplankton and the key environmental factors influencing the retention of MPs in zooplankton are largely unknown. For the first time, the characteristics of MPs in copepods across four seasons in Jiaozhou Bay. The abundance, shape, size, and chemical composition of the MPs in copepods were investigated, and the relationships between the MP/copepod value and key environmental factors were analyzed. The results revealed a significant seasonal difference in MP/copepod values in Jiaozhou Bay. MP/copepod values were 0.26, 0.23, 0.14 and 0.16 in February, May, August and November, respectively. The MP/copepod value was significantly higher in winter and spring than in summer and significantly higher in the estuarine zone than in other zones. Seawater temperature was negatively correlated with the MP/copepod value. No significant seasonal differences were detected in the characteristics of MPs in copepods in Jiaozhou Bay. The size of MPs in copepods ranged from 90 to 2485 μm, with an average of 454 ± 376 μm. Fiber MPs were the most risky to copepods, accounting for 92% of the total ingested MPs. In terms of the chemical composition of the MPs, a total of 11 polymers were detected in copepods in Jiaozhou Bay in the four seasons. The main components were polyester and cellophane (41.9% and 25.7%, respectively). This study provides the key parameters of the MPs in copepods in Jiaozhou Bay and is an important basis for further ecological risk assessments of MPs.The chronic effects of low-level MP retention on copepods, the impact of fibers on copepods, and appropriate assessments of MP risk under different environmental conditions are recommended as research topics for the next step toward developing an environmentally relevant MP risk assessment. The main findingThe seasonal characteristics of microplastics ingested by copepods in Jiaozhou Bay were revealed.

Transport and Retention of Microplastics in Saturated Porous Media with Peanut Shell Biochar (PSB) and MgO-PSB Amendment: Co-Effects of Cation and Humic Acid

Transport and Retention of Microplastics in Saturated Porous Media with Peanut Shell Biochar (PSB) and MgO-PSB Amendment: Co-Effects of Cation and Humic Acid

Механизмы перехвата пластиковых микрочастиц буферными зонами из макрофитов

Environmental pollution by resistant to degradation microparticles of synthetic polymer materials (microplastics) is one of the growing global problems nowadays. At the same time, research on the behavior of plastic microparticles in the environment is only at an early stage, as well as the development of methods for preventing and regulating microplastic contamination of water bodies. For the first time in world scientific practice, the author proposed to use the barrier role of macrophytes for these purposes. А number of mechanisms directly and indirectly leading to the microplastic retention by macrophytes have been identified based on field and laboratory experiments with plastic microparticles with different polymer matrix (polyethylene, polystyrene, polyethylene terephthalate, polyester) and air-water and immersed vegetation, as well as plants with leaves floating on the water surface. According to the predominance of a particular physical process, these mechanisms can be combined into four groups: (1) The appearance of additional resistance to the movement of water and air masses. Change in the kinematic structure of water and air flows promotes slowing down the movement of microparticles, their sedimentation and retention by plants; (2) Decreasing the kinetic energy of wind waves and raindrops by thickets of macrophytes prevents repeated movement of already trapped microparticles; (3) Mechanical retention of plastic microparticles occurs as a result of the existence of irregularities in the structure of plants, sieve-like structures made of interweaving of stems and leaves, the bulk of plant litter, adhesion of plant surfaces and microparticles, which is enhanced by the sticky surfaces of the periphyton; (4) The attraction and adhesion of plastic microparticles to plants and to each other occurs as a result of the interaction of electric fields.

Microplastic retention by marine vegetated canopies: Simulations with seagrass meadows in a hydraulic flume.

Marine canopies formed by seagrass and other coastal vegetated ecosystems could act as sinks of microplastics for being efficient particle traps. Here we investigated for the first time the occurrence of microplastic retention by marine canopies in a hydraulic flume under unidirectional flow velocities from 2 to 30cms-1. We used as model canopy-forming species the seagrass Zostera marina with four canopy shoot density (0, 50, 100, 200 shoots m-2), and we used as microplastic particles industrial pristine pellets with specific densities from 0.90 to 1.34gcm-3 (polypropylene PP; polystyrene PS; polyamide 6PA; and polyethylene terephthalate PET). Overall, microplastics particles transported with the flow were retained in the seagrass canopies but not in bare sand. While seagrass canopies retained floating microplastics (PP) only at low velocities (<12cms-1) due to a barrier created by the canopy touching the water surface, the retention of sinking particles (PS, PA, PET) occurred across a wider range of flow velocities. Our simulations revealed that less dense sinking particles (PS) might escape from the canopy at high velocities, while denser sinking particles can be trapped in scouring areas created by erosive processes around the eelgrass shoots. Our results show that marine canopies might act as potential barriers or sinks for microplastics at certain bio-physical conditions, with the probability of retention generally increasing with the seagrass shoot density and polymer specific density and decreasing with the flow velocity. We conclude that seagrass meadows, and other aquatic canopy-forming ecosystems, should be prioritized habitats in assessment of microplastic exposure and impact on coastal areas since they may accumulate high concentration of microplastic particles that could affect associated fauna.

Systematic identification of microplastics in abyssal and hadal sediments of the Kuril Kamchatka trench.

The occurrence of microplastics throughout marine environments worldwide, from pelagic to benthic habitats, has become serious cause for concern. Hadal zones were recently described as the "trash bins of the oceans" and ultimate sink for marine plastic debris. The Kuril region covers a substantial area of the North Pacific Ocean and is characterised by high biological productivity, intense marine traffic through the Kuril straits, and anthropogenic activity. Moreover, strong tidal currents and eddy activity, as well as the influence of Pacific currents, have the potential for long distance transport and retention of microplastics in this area. To verify the hypothesis that the underlying Kuril Kamchatka Trench might accumulate microplastics from the surrounding environments and act as the final sink for high quantities of microplastics, we analysed eight sediment samples collected in the Kuril Kamchatka Trench at a depth range of 5143-8250m during the Kuril Kamchatka Biodiversity Studies II (KuramBio II) expedition in summer 2016. Microplastics were characterised via Micro Fourier Transform Infrared spectroscopy. All samples were analysed in their entirety to avoid inaccuracies due to extrapolations of microplastic concentrations and polymer diversities, which would otherwise be based on commonly applied representative aliquots. The number of microplastic particles detected ranged from 14 to 209kg-1 sediment (dry weight) with a total of 15 different plastic polymers detected. Polypropylene accounted for the largest proportion (33.2%), followed by acrylates/polyurethane/varnish (19%) and oxidized polypropylene (17.4%). By comparing extrapolated sample aliquots with in toto results, it was shown that aliquot-based extrapolations lead to severe under- or overestimations of microplastic concentrations, and an underestimation of polymer diversity.

Estimation of the uptake and gut retention of microplastics in juvenile marine fish: Mummichogs (Fundulus heteroclitus) and red seabreams (Pagrus major)

We investigated the impact of microplastics (MPs) on marine fish by estimating the uptake and retention by mummichogs (Fundulus heteroclitus) and red seabreams (Pagrus major) of MPs similar in size (≥0.25 mm) and composition (polyethylene) to MPs detected in fish intestines. Results revealed a correlation between MP concentrations in aquarium water and the content of MPs in the gastrointestinal tracts of exposed fish. More than 95% were excreted from both species within 25 h; this retention time is similar to the processing time of food items. The rate of excretion showed little dependence on MP size, but there was some dependence on fish species and MP shape. These results suggest that MPs similar to those we studied have little direct adverse impact on these two marine fish species.