Respirable Mass Research Articles

Characterization of airborne dust emissions from three types of crushed multi-walled carbon nanotube-enhanced concretes

Dispersing Multi-Walled Carbon Nanotubes (MWCNTs) into concrete at low (<1 wt% in cement) concentrations may improve concrete performance and properties and provide enhanced functionalities. When MWCNT-enhanced concrete is fragmented during remodelling or demolition, the stiff, fibrous and carcinogenic MWCNTs will, however, also be part of the respirable particulate matter released in the process. Consequently, systematic aerosolizing of crushed MWCNT-enhanced concretes in a controlled environment and measuring the properties of this aerosol can give valuable insights into the characteristics of the emissions such as concentrations, size range and morphology. These properties impact to which extent the emissions can be inhaled as well as where they are expected to deposit in the lung, which is critical to assess whether these materials might constitute a future health risk for construction and demolition workers. In this work, the impact from MWCNTs on aerosol characteristics was assessed for samples of three concrete types with various amounts of MWCNT, using a novel methodology based on the continuous drop method. MWCNT-enhanced concretes were crushed, aerosolized and the emitted particles were characterized with online and offline techniques. For light-weight porous concrete, the addition of MWCNT significantly reduced the respirable mass fraction (RESP) and particle number concentrations (PNC) across all size ranges (7 nm – 20 μm), indicating that MWCNTs dampened the fragmentation process by possibly reinforcing the microstructure of brittle concrete. For normal concrete, the opposite could be seen, where MWCNTs resulted in drastic increases in RESP and PNC, suggesting that the MWCNTs may be acting as defects in the concrete matrix, thus enhancing the fragmentation process. For the high strength concrete, the fragmentation decreased at the lowest MWCNT concentration, but increased again for the highest MWCNT concentration. All tested concrete types emitted <100 nm particles, regardless of CNT content. SEM imaging displayed CNTs protruding from concrete fragments, but no free fibres were detected.

Use of the dustiness index in combination with the handling energy factor for exposure modelling of nanomaterials

The use of modelling tools in the occupational hygiene community has increased in the last years to comply with the different existing regulations. However, limitations still exist mainly due to the difficulty to obtain certain key parameters such as the emission rate, which in the case of powder handling can be estimated using the dustiness index (DI). The goal of this work is to explore the applicability and usability of the DI for emission source characterization and occupational exposure prediction to particles during nanomaterial powder handling. Modelling of occupational exposure concentrations of 13 case scenarios was performed using a two-box model as well as three nano-specific tools (Stoffenmanager nano, NanoSafer and GUIDEnano). The improvement of modelling performance by using a derived handling energy factor (H) was explored. Results show the usability of the DI for emission source characterization and respirable mass exposure modelling of powder handling scenarios of nanomaterials. A clear improvement in modelling outcome was obtained when using derived quartile-3 H factors with, 1) Pearson correlations of 0.88 vs. 0.52 (not using H), and 2) ratio of modelled/measured concentrations ranging from 0.9 to 10 in 75% cases vs. 16.7% of the cases when not using H. Particle number concentrations were generally underpredicted. Using the most conservative H values, predictions with ratios modelled/measured concentrations of 0.4–3.6 were obtained.

6 Characterization of Aerosolized Particles Generated During Cutting of Carbon Nanotubes-Embedded Concrete

Abstract Engineered nanomaterials are revolutionizing many industries, but little is known about potential exposures during the life cycle of nano-enabled composites. This study was conducted to characterize aerosolized particles using direct-reading instruments and integrated air samplers during cutting multi-walled carbon nanotubes (MWCNT)-embedded concrete cylinder blocks. Three types of blocks, 0% (reference), low%, and high% MWCNT, were tested in a specially designed enclosure housing an apparatus for the cutting of a block with an automated computer-controlled process. The highest particle number concentration (163,821 particles/cm3) was measured for the reference cylinder, while others showed similar concentrations (131,689 particles/cm3 and 140,954 particles/cm3 for the low% and high% blocks, respectively). Regardless of the cylinder type, the size-selected particle number concentrations revealed one main mode with a peak at 0.72 µm indicating no shift in the size distribution from addition(s) of MWCNT. Respirable mass concentrations were 342 mg/m3, 405 mg/m3, and 432 mg/m3 for the reference, low%, and high% blocks, respectively. The mass median aerodynamic diameters were similar, 5.23 µm for the reference and 5.05 µm for both low% and high% blocks, indicating a predominant respirable fraction. Respirable particles (quartz, feldspar, paste, etc.) often appeared to be agglomerated materials that included both paste and aggregate minerals. No free MWCNT were observed by electron microscopy from low% and high% samples. These initial studies found no evidence of free MWCNT by cutting concrete test blocks and only minor differences in the particulate aerosol generated, which included a general increase in respirable mass with increasing % CNT.

109 Inter- and Intra-Laboratory Comparison of 6 Dustiness Testing Methods: Towards the Development of an OECD Testing Guideline

Abstract Dustiness is a key parameter describing the ability of powder materials to generate dust during agitation. The main goal of this work was to generate and assess the scientific basis for the validation and applicability of 6 dustiness methods to nanomaterials, and development of a subsequent OECD testing guideline. Six dustiness methods (rotating drum, small rotating drum, continuous drop, vortex shaker, fluidizer and venturi) were subjected to an intra- and inter-laboratory comparison (ILC) in which 15 international laboratories participated. ILC tests were conducted for 6 materials (3 TiO2 and 3 SiO2) of different chemical natures and dustiness levels. Each participating laboratory conducted at least 3 replicates per material. Harmonization of procedures, methods and data treatment took place prior to testing. Results from the ILC were assessed considering the different reported metrics such as respirable mass and particle number dustiness index. Overall, the intralaboratory variability for the different methods and metrics was under 30%. Variation between laboratories was generally higher for respirable mass than particle number dustiness index. These variations were mostly attributed to differences in setups such as tubing length or instrumentation. All methods except the venturi, which was characteristic for presenting low differences between materials and opposed classification to the rest of the methods, showed relatively similar material ranking. For all methods and laboratories the calculated z-score (measure of the deviation of each laboratory from the true value) was &amp;lt;2 as based on ISO 13528, which indicates gratifying results. Funding: EU H2020 Research and Innovation Programme under Grant Agreement 814401.

7 Construction and Characterization of a Thermal Spray Coating Aerosol Generator

Abstract Thermal spray coating (TSC) is a surface treatment process whereby feedstock material is sprayed onto surfaces under pressure where it solidifies and forms a solid coating. In metal TSC processes, large quantities of aerosols, including fine and ultrafine metal particles are generated. However, exposure assessment for TSC is lacking. The goal of this study was to construct a TSC aerosol generation system and to characterize the physicochemical properties of aerosols generated during coating processes. A computer-controlled, automated electric arc wire-TSC aerosol generator system was built in an enclosed room, where a rotary motor rotates a metal feedstock pipe in circular and up-and-down directions to allow even deposition of coating material on the pipe surface. The characteristics of aerosolized particles during spray coating using a stainless-steel wire (PMET 720) showed that: 1) respirable mass concentrations ranged from 142–218 mg/m3 (3 spray shots with each shot of 1-sec during 20-min sampling), 2) diameter of peak particle number concentrations was between 360 nm and 400 nm, 3) mass median aerodynamic diameter determined by an impactor ranged from 290–370 nm, 4) particle morphology was observed to be diverse including chain-like agglomerates and spherical and cylinder-like shapes, and 5) metal composition was 80% iron, 17% chromium, and 3% manganese with trace amounts of nickel and copper. These findings are limited to one wire type and suggests the need for further investigations evaluating various parameters (e.g., wire/powder types, high/low energy, ventilation on/off) to obtain emission rates and recommend control measures.

129 A task-Based Approach to Nanomaterials Exposure Assessment in the Construction Trades

Abstract While the critical task of evaluating the hazards of nanomaterials continues, exposure assessments can provide additional information to safeguard workers. The frequent exposure of construction workers to inhalation hazards underscores a pressing need to characterize and quantify nanomaterials in aerosols generated during construction activities. Research was conducted in partnership with affected building trades unions and in collaboration with NIOSH toxicologists to obtain occupationally relevant exposure data. Initial studies took place in a test chamber, in which a skilled tradesperson sprayed or sanded paints and coatings containing ZnO, TiO2, or Ag nanoparticles. The current study, conducted outdoors, investigated exposure to graphene nanoplatelets during cutting, grinding, and tuckpointing of cementitious composites. Personal breathing zone samples were analyzed for elemental carbon (EC) respirable mass concentration and by transmission electron microscopy (TEM) with energy-dispersive x-ray spectroscopy. Wet methods and local exhaust ventilation effectively reduced exposure to graphene; respirable EC was non-detectable when using exposure controls versus up to 3 mg m-3 without. A high proportion of graphene particles observed by TEM were free and not bound to the cement matrix. Compared to the unincorporated graphene, the dimensions of graphene particles observed in air samples were smaller, suggesting a potential physical transformation prior to release from the matrix. Given the dustiness of construction environments, analysis of filter loading prior to collection of TEM samples proved methodologically valuable. These results provide actionable information about exposure risks and controls and support further investigation of the extent to which graphene may alter the toxicity of cement dust.

Efficacy of dental evacuation systems for aerosol exposure mitigation in dental clinic settings

Dental personnel are ranked among the highest risk occupations for exposure to SARS-CoV-2 due to their close proximity to the patient’s mouth and many aerosol generating procedures encountered in dental practice. One method to reduce aerosols in dental settings is the use of intraoral evacuation systems. Intraoral evacuation systems are placed directly into a patient’s mouth and maintain a dry field during procedures by capturing liquid and aerosols. Although multiple intraoral dental evacuation systems are commercially available, the efficacy of these systems is not well understood. The objectives of this study were to evaluate the efficacy of four dental evacuation systems at mitigating aerosol exposures during simulated ultrasonic scaling and crown preparation procedures. We conducted real-time respirable (PM4) and thoracic (PM10) aerosol sampling during ultrasonic scaling and crown preparation procedures while using four commercially available evacuation systems: a high-volume evacuator (HVE) and three alternative intraoral systems (A, B, C). Four trials were conducted for each system. Respirable and thoracic mass concentrations were measured during procedures at three locations including (1) near the breathing zone (BZ) of the dentist, (2) edge of the dental operatory room approximately 0.9 m away from the mannequin mouth, and (3) hallway supply cabinet located approximately 1.5 m away from the mannequin mouth. Respirable and thoracic mass concentrations measured during each procedure were compared with background concentrations measured in each respective location. Use of System A or HVE reduced thoracic (System A) and respirable (HVE) mass concentrations near the dentist’s BZ to median background concentrations most often during the ultrasonic scaling procedure. During the crown preparation, use of System B or HVE reduced thoracic (System B) and respirable (HVE or System B) near the dentist’s BZ to median background concentrations most often. Although some differences in efficacy were noted during each procedure and aerosol size fraction, the difference in median mass concentrations among evacuation systems was minimal, ranging from 0.01 to 1.48 µg/m3 across both procedures and aerosol size fractions.

Evaluation of One- and Two-Box Models as Particle Exposure Prediction Tools at Industrial Scale.

One- and two-box models have been pointed out as useful tools for modelling indoor particle exposure. However, model performance still needs further testing if they are to be implemented as trustworthy tools for exposure assessment. The objective of this work is to evaluate the performance, applicability and reproducibility of one- and two-box models on real-world industrial scenarios. A study on filling of seven materials in three filling lines with different levels of energy and mitigation strategies was used. Inhalable and respirable mass concentrations were calculated with one- and two-box models. The continuous drop and rotating drum methods were used for emission rate calculation, and ranges from a one-at-a-time methodology were applied for local exhaust ventilation efficiency and inter-zonal air flows. When using both dustiness methods, large differences were observed for modelled inhalable concentrations but not for respirable, which showed the importance to study the linkage between dustiness and processes. Higher model accuracy (ratio modelled vs. measured concentrations 0.5–5) was obtained for the two- (87%) than the one-box model (53%). Large effects on modelled concentrations were seen when local exhausts ventilation and inter-zonal variations where parametrized in the models. However, a certain degree of variation (10–20%) seems acceptable, as similar conclusions are reached.

Characterizing and Comparing Emissions of Dust, Respirable Crystalline Silica, and Volatile Organic Compounds from Natural and Artificial Stones.

The frequency of cases of accelerated silicosis associated with exposure to dust from processing artificial stones is rapidly increasing globally. Artificial stones are increasingly popular materials, commonly used to fabricate kitchen and bathroom worktops. Artificial stones can contain very high levels of crystalline silica, hence cutting and polishing them without adequate exposure controls represents a significant health risk. The aim of this research was to determine any differences in the emission profiles of dust generated from artificial and natural stones when cutting and polishing. For artificial stones containing resins, the nature of the volatile organic compounds (VOCs) emitted during processing was also investigated. A selection of stones (two natural, two artificial containing resin, and one artificial sintered) were cut and polished inside a large dust tunnel to characterize the emissions produced. The inhalable, thoracic, and respirable mass concentrations of emissions were measured gravimetrically and the amount of crystalline silica in different size fractions was determined by X-ray diffraction. Emissions were viewed using scanning electron microscopy and the particle size distribution was measured using a wide range aerosol spectrometer. VOCs emitted when cutting resin-artificial stones were also sampled. The mass of dust emitted when cutting stones was higher than that emitted when polishing. For each process, the mass of dust generated was similar whether the stone was artificial or natural. The percentage of crystalline silica in bulk stone is likely to be a reasonable, or conservative, estimate of that in stone dust generated by cutting or polishing. Larger particles were produced when cutting compared with when polishing. For each process, normalized particle size distributions were similar whether the stone was artificial or natural. VOCs were released when cutting resin-artificial stones. The higher the level of silica in the bulk material, the higher the level of silica in any dust emissions produced when processing the stone. When working with new stones containing higher levels of silica, existing control measures may need to be adapted and improved in order to achieve adequate control.

Occupational exposure risk during spraying of biocidal paint containing silver nanoparticles

The study assessed potential to exceed occupational exposure limits while spraying paint with and without a silver nanoparticle biocidal additive. A tradesperson performed the tasks in a sealed chamber with filtered air supply. Integrated air sampling entailed transmission electron microscopy with energy dispersive X-ray analysis, direct-reading of particle number concentrations, and determination of silver mass concentration by NIOSH Method 7300. Silver nanoparticles were primarily embedded in paint spray droplets but also observed as isolated particles. Using an α-level of 0.05, median nanoparticle number concentrations did not differ significantly when spraying conventional vs. biocidal paint, although statistically significant differences were observed at specific particle size ranges <100 nm. The geometric mean concentration of total silver while spraying biocidal paint (n = 6) was 2.1 µg/m3 (95% CI: 1.5–2.8 µg/m3), and no respirable silver was detected (<0.50 µg/m3). The results address a lack of silver nanoparticle exposure data in construction and demonstrate the feasibility of a practical sampling approach. Given similar conditions, the measurements suggest a low probability of exceeding a proposed silver nanoparticle exposure limit of 0.9 µg/m3 as an airborne 8-hr time-weighted average respirable mass concentration. A full workday of exposure to respirable silver at the highest possible level in this study (<0.50 µg/m3) would not exceed the exposure limit, although limitations in comparing short task-based exposures to an 8-hr exposure limit must be noted. There was airflow in the study chamber, whereas exposure levels could increase over time in work environments lacking adequate ventilation. Potential to exceed the exposure limit hinged upon the respirable fraction of the paint mist, which could vary by material and application method. Additional research would improve understanding of silver nanoparticle exposure risks among construction trades, and biological responses to these exposures. Given the potential for exposure variability on construction jobsites, safety and health professionals should be cognizant of methods to assess and control silver nanoparticle exposures.

Exposure characterization and risk assessment of ultrafine particles from the blast furnace process in a steelmaking plant.

ObjectivesThis study aimed to clarify the exposure characteristics and risks of ultrafine particles from the blast furnace process and to provide a reasonable control strategy for protecting the health of workers.MethodsThe blast furnace location of a steelmaking plant was selected as a typical investigation site. A membrane‐based sampling system was used to collect ultrafine particles to analyze their morphology and elemental compositions. A real‐time system was used to monitor the total number concentration (NC), total respirable mass concentration (MC), surface area concentration (SAC), and size distribution by number. The risk level of ultrafine particles was analyzed using the Stoffenmanager‐Nano model.ResultsThe total NC, total MC, and SAC increased significantly relative to background concentrations after slag releasing started and decreased gradually after the activity stopped. The three highest total concentrations during slag releasing were 3‐10 times higher than those of the background or non‐activity period. The ultrafine particles were mainly gathered at 10.4 or 40 nm, and presented as lump‐like agglomerates. The metal elements (Al and Pt) in the ultrafine particles originated from slag and iron ore. The risk level of the ultrafine particles was high, indicating the existing control measures were insufficient.ConclusionsThe blast furnace workers are at high risk due to exposure to high levels of ultrafine particles associated with working activity and with a bimodal size distribution. The existing control strategies, including engineering control, management control, and personal protection equipment need to be improved.

Occupational Exposure and Environmental Release: The Case Study of Pouring TiO2 and Filler Materials for Paint Production.

Pulmonary exposure to micro- and nanoscaled particles has been widely linked to adverse health effects and high concentrations of respirable particles are expected to occur within and around many industrial settings. In this study, a field-measurement campaign was performed at an industrial manufacturer, during the production of paints. Spatial and personal measurements were conducted and results were used to estimate the mass flows in the facility and the airborne particle release to the outdoor environment. Airborne particle number concentration (1 × 103–1.0 × 104 cm−3), respirable mass (0.06–0.6 mg m−3), and PM10 (0.3–6.5 mg m−3) were measured during pouring activities. In overall; emissions from pouring activities were found to be dominated by coarser particles >300 nm. Even though the raw materials were not identified as nanomaterials by the manufacturers, handling of TiO2 and clays resulted in release of nanometric particles to both workplace air and outdoor environment, which was confirmed by TEM analysis of indoor and stack emission samples. During the measurement period, none of the existing exposure limits in force were exceeded. Particle release to the outdoor environment varied from 6 to 20 g ton−1 at concentrations between 0.6 and 9.7 mg m−3 of total suspended dust depending on the powder. The estimated release of TiO2 to outdoors was 0.9 kg per year. Particle release to the environment is not expected to cause any major impact due to atmospheric dilution

Nanoparticle Exposure and Workplace Measurements During Processes Related to 3D Printing of a Metal Object.

Metal 3D printing has many potential uses within prototyping and manufacturing. Selective laser melting (SLM) is a process that uses metal powders in the micrometer range as printing material. The particle release from the entire SLM printing process is not well-studied. While the 3D printing itself often occurs in a sealed chamber, activities related to the process can potentially release harmful metal particles to the indoor working environment through resuspension of the printing powder or via incident nanoparticles generated during printing. The objective of this study was to improve the understanding of particle exposure in work processes associated with 3D printing and potential needs for interventions by a case study conducted in a 3D printing facility. In this setting, direct release and dispersion of particles throughout the workspace from processes related to metal 3D printing was investigated. The release from five activities were studied in detail. The activities included post-printing cleaning, object annealing, and preparation of new base substrate for the next printing was. Three of the five measured activities caused particles number concentrations in the working environment to increase above background levels which were found to be 8·102 cm−3. Concentrations during chamber emptying and the open powder removal system (PRS) cleaning processes increased to 104 and 5·103 cm−3, respectively, whereas grinding activity increased number concentrations to 2.5·105 cm−3. Size distributions showed that particles were mainly smaller than 200 nm. Respirable mass concentrations were 50.4 μg m−3, collected on filters. This was corroborated by respirable mass measured with a DustTrak of 58.4 μg m−3. Respirable mass concentrations were below the occupational exposure limits in Denmark for an 8 h time-weighted average.

Direct infrared spectroscopy for the size-independent identification and quantification of respirable particles relative mass in mine dusts

Due to the global need for energy and resources, many workers are involved in underground and surface mining operations where they can be exposed to potentially hazardous crystalline dust particles. Besides commonly known alpha quartz, a variety of other materials may be inhaled when a worker is exposed to airborne dust. To date, the challenge of rapid in-field monitoring, identification, differentiation, and quantification of those particles has not been solved satisfactorily, in part because conventional analytical techniques require laboratory environments, complex method handling, and tedious sample preparation procedures and are in part limited by the effects of particle size. Using a set of the three most abundant minerals in limestone mine dust (i.e., calcite, dolomite, and quartz) and real-world dust samples, we demonstrate that Fourier transform infrared (FTIR) spectroscopy in combination with appropriate multivariate data analysis strategies provides a versatile tool for the identification and quantification of the mineral composition in relative complex matrices. An innovative analytical method with the potential of in-field application for quantifying the relative mass of crystalline particles in mine dust has been developed using transmission and diffuse reflection infrared Fourier transform spectroscopy (DRIFTS) within a unified multivariate model. This proof-of-principle study shows how direct on-site quantification of crystalline particles in ambient air may be accomplished based on a direct-on-filter measurement, after mine dust particles are collected directly onto PVC filters by the worker using body-mounted devices. Without any further sample preparation, these loaded filters may be analyzed via transmission infrared (IR) spectroscopy and/or DRIFTS, and the mineral content is immediately quantified via a partial least squares regression (PLSR) algorithm that enables the combining of the spectral data of both methods into a single robust model. Furthermore, it was also demonstrated that the size regime of dust particles may be classified into groups of hazardous and less hazardous size regimes. Thus, this technique may provide additional essential information for controlling air quality in surface and underground mining operations.Graphical

Design and performance of UPAS inlets for respirable and thoracic mass sampling

The Ultrasonic Personal Aerosol Sampler (UPAS) is a small, lightweight, and quiet sampler that collects airborne particulate matter on a filter for gravimetric or compositional analysis. The objective of this work was to develop UPAS inlets with collection efficiencies that match criteria for respirable or thoracic mass sampling. The two-stage inlet for respirable mass described here utilizes an impaction stage and a cyclone, whereas the one-stage inlet for thoracic mass sampling utilizes a circular slot impactor. Inlet designs are based on particle collection theory used in conjunction with an optimization algorithm to predict initial inlet dimensions; these predictions were the starting points for experiments that finalized dimensions and operating conditions. Both the respirable mass inlet and the thoracic mass inlet described here are interchangeable with the UPAS, and both have efficiencies that match well with their respective standards. With either inlet, the collected sample should be within ±5% of what the standard specifies for aerosols with reasonably broad size distributions.

Designing inhalable metal organic frameworks for pulmonary tuberculosis treatment and theragnostics via spray drying.

Inhalable metal organic framework (MOF) aerosols have been developed via spray drying as a therapy for multi-drug resistant (MDR) tuberculosis (TB). The CuPOA2 (pyrazinoate acid) MOFs can be tailored to exhibit a respirable mass median aerodynamic diameter (MMAD) of 2.6 μm. This method is repeated to manufacture Gd0.1Cu0.9(POA)2 MOFs for inhalable theragnostics.

Evaluation of patients’ real-world post-dispensing use and storage environments of tiotropium bromide Respimat® soft mist inhaler on its in vitro dose delivery and lung deposition

BackgroundOral inhalation is the main drug delivery route for treating obstructive lung conditions. Thus, many inhaler devices with various design and pharmaceutical formulation have been introduced. The fine particle dose (FPD) and mass median aerodynamic diameter (MMAD ≤ 5 μm) of the aerosol delivered dose (DD) dictate the therapeutically effective peripheral lung deposition. This study evaluated the in vitro aerosol emission performance of tiotropium bromide emitted from Spiriva® Respimat® soft mist inhalers (R) after living under patients’ real-world, post-dispensing handling environments. MethodsThis was a two-stage investigation. In the first clinical stage, research ethical approval was obtained to enrol patients already been using R for at least 3 months. Those who signed consent were given both new R to use and temperature and relative humidity (RH) handheld, portable data loggers to keep in the vicinity of the given R. The participants returned the given R and data loggers after 2 weeks. Patient recruitment took place in Amman, Jordan, during the summer (RS) and winter (RW). Subsequently, in the second laboratory stage, other R were strictly stored at an average of 21.0 °C and 46.9% RH as control (RC). The Next Generation Impactor (NGI) was used to evaluate the RS, RW and RC. The NGI was operated at a flow rate of 30 L/min. ResultsThe RS were exposed to an average (range) 23.6 °C (18.2–37.5 °C) and 43.8% RH (21.4–60.0% RH) that were statistically comparable (p > 0.05) to that of the RW; 17.3 °C (13.2–26.7 °C) and 52.8% RH (26.3–69.1% RH). The RW and RC retention environments were statistically different (p < 0.05), whilst the RS and RC had comparable (p > 0.05) conditions. No significant differences (p > 0.05) were found in the tiotropium bromide DD (2.39 vs 2.43 μg), FPD (0.88 vs 0.90 μg) and MMAD (5.1 vs 4.98 μm) between the RS and RW, respectively. Compared to the RC inhalers, both the RS and RW devices had significantly higher FPD and relatively smaller tiotropium bromide particles. ConclusionsUsing the R under the fluctuating summer and winter environments of our patients would not affect its overall tiotropium bromide emission performance. The significant increase in the respirable mass of the RS and RW might be offset by the increase in particles <1 μm particularly in patients with poor inhaler technique.

Sources of error and variability in particulate matter sensor network measurements

The quality of mass concentration estimates from increasingly popular networks of low-cost particulate matter sensors depends on accurate conversion of sensor output (e.g., voltage) into gravimetric-equivalent mass concentration, typically using a calibration procedure. This study evaluates two important sources of variability that lead to error in estimating gravimetric-equivalent mass concentration: the temporal changes in sensor calibration and the spatial and temporal variability in gravimetric correction factors. A 40-node sensor network was deployed in a heavy vehicle manufacturing facility for 8 months. At a central location in the facility, particulate matter was continuously measured with three sensors of the network and a traditional, higher-cost photometer, determining the calibration slope and intercept needed to translate sensor output to photometric-equivalent mass concentration. Throughout the facility, during three intensive sampling campaigns, respirable mass concentrations were measured with gravimetric samplers and photometers to determine correction factors needed to adjust photometric-equivalent to gravimetric-equivalent mass concentration. Both field-determined sensor calibration slopes and intercepts were statistically different than those estimated in the laboratory (α = 0.05), emphasizing the importance of aerosol properties when converting voltage to photometric-equivalent mass concentration and the need for field calibration to determine slope. Evidence suggested the sensors’ weekly field calibration slope decreased and intercept increased, indicating the sensors were deteriorating over time. The mean correction factor in the cutting and shot blasting area (2.9) was substantially and statistically lower than that in the machining and welding area (4.6; p = 0.01). Therefore, different correction factors should be determined near different occupational processes to accurately estimate particle mass concentrations.

长江中游地区可吸入颗粒物气团输送轨迹的时空差异分析

长江中游地区可吸入颗粒物气团输送轨迹的时空差异分析

On the Relationship between Exposure to Particles and Dustiness during Handling of Powders in Industrial Settings

Exposure to ceramic powders, which is frequent during handling operations, is known to cause adverse health effects. Finding proxy parameters to quantify exposure is useful for efficient and timely exposure assessments. Worker exposure during handling of five materials [a silica sand (SI1), three quartzes (Q1, Q2, and Q3), and a kaolin (K1)] with different particle shape (prismatic and platy) and sizes (3.4-120 µm) was assessed. Materials handling was simulated using a dry pendular mill under two different energy settings (low and high). Three repetitions of two kilos of material were carried out per material and energy conditions with a flow rate of 8-11 kg h-1. The performance of the dustiness index as a predictor of worker exposure was evaluated correlating material's dustiness indexes (with rotating drum and continuous drop) with exposure concentrations. Significant impacts on worker exposure in terms of inhalable and respirable mass fractions were detected for all materials. Mean inhalable mass concentrations during background were always lower than 40 µg m-3 whereas during material handling under high energy settings mean concentrations were 187, 373, 243, 156, and 430 µg m-3 for SI1, Q1, Q2, Q3, and K1, respectively. Impacts were not significant with regard to particle number concentration: background particle number concentrations ranged between 10 620 and 46 421 cm-3 while during handling under high energy settings they were 20 880 - 40 498 cm-3. Mean lung deposited surface area during background ranged between 27 and 101 μm2 cm-3 whereas it ranged between 22 and 42 μm2 cm-3 during materials handling. TEM images evidenced the presence of nanoparticles (≤100 nm) in the form of aggregates (300 nm-1 µm) in the worker area, and a slight reduction on mean particle size during handling was detected. Dustiness and exposure concentrations showed a high degree of correlation (R2 = 0.77-0.97) for the materials and operating conditions assessed, suggesting that dustiness could be considered a relevant predictor for workplace exposure. Nevertheless, the relationship between dustiness and exposure is complex and should be assessed for each process, taking into account not only material behaviour but also energy settings and workplace characteristics.