Resonance Quality Research Articles

Inducing exceptional points, enhancing plasmon quality and creating correlated plasmon states with modulated Floquet parametric driving.

The control of low frequency collective modes in solids by light presents important challenges and opportunities for condensed matter physics. We propose a method to parametricallydrive low THz range collective modes in an interacting many body system using Floquet driving at optical frequencies with a modulated amplitude. We demonstrate that it can be used to design plasmonic time-varying media with singular dispersions. Plasmons near resonance with half the modulation frequency exhibit two lines of exceptional points connected by dispersionless states. Above a critical driving strength, resonant plasmon modes become unstable and undergo a continuous transition towards a crystal-like structure stabilized by interactions and nonlinearities. This new state breaks the discrete time translational symmetry of the drive as well as the translational and rotational spatial symmetries of the system and exhibits soft, Goldstone-like phononic excitations. Below the instability threshold, our method can be used to enhance the quality of plasmon resonances.

Association between temporomandibular joint dysfunction signs and symptoms, mental health indices, and MRI diagnoses: should we scan patients?

Temporomandibular joint dysfunction (TMD) is a common condition; yet multifactorial in nature. Our understanding of the interplay between clinical symptoms in relation to Magnetic resonance imaging (MRI) findings and quality of life is limited. Our primary objective was to identify features of TMD contributing to anxiety and depression. Our secondary objective was to determine whether clinical symptoms, baseline characteristics, and mental health outcomes are associated with underlying disease severity, as determined by MRI. A retrospective analysis of 202 TMD patients was performed. Mental health outcomes were quantified using the IMPARTS psychometric questionnaire (Visual Analog Score, VAS; Generalised Anxiety Disorder Assessment, GAD7;, Patient Health Questionnaire, PHQ-9), and patients were categorised based on temporomandibular joint pathology severity (normal, anterior disc displacement with reduction, anterior disc displacement without reduction and severe degeneration). On multivariable analyses, both higher anxiety (p<0.001) and depression (p<0.001) scores on IMPARTS assessment were associated with worst perceived pain (on VAS). Unilateral joint involvement (OR2.48[95%CI 1.20;5.46],p=0.018), locking (OR4.28[95%CI 1.63;13.63],p=0.006) , and clicking (OR2.14[95%CI1.05;4.60],p=0.006) were significantly associated with increased odds of an abnormal TMJ on MRI, whereas higher anxiety scores (OR0.93[95%CI 0.88;0.99],p=0.006) and male gender (OR0.35[95%CI 0.15;0.79],p=0.012) were significantly predictive of a normal joint morphology on MRI. Our findings support a complex interplay between patient symptomology, mental health outcomes and objective radiologically-defined joint pathology in the TMD patient population.

A microsystem for in vivo wireless monitoring of plastic biliary stents using magnetoelastic sensors.

With an interest in monitoring the patency of stents that are used to treat strictures in the bile duct, this paper reports the investigation of a wireless sensing system to interrogate a microsensor integrated into the stent. The microsensor is comprised of a 28-μm-thick magnetoelastic foil with 8.25-mm length and 1-mm width. Magnetic biasing is provided by permanent magnets attached to the foil. These elements are incorporated into a customized 3D polymeric package. The system electromagnetically excites the magnetoelastic resonant sensor and measures the resulting signal. Through shifts in resonant frequency and quality factor, the sensor is intended to provide an early indication of sludge accumulation in the stent. This work focuses on challenges associated with sensor miniaturization and placement, wireless range, drive signal feedthrough, and clinical use. A swine specimen in vivo experiment is described. Following endoscopic implantation of the sensor enabled plastic stent into the bile duct, at a range of approximately 17 cm, the signal-to-noise ratio of ~106 was observed with an interrogation time of 336 s. These are the first reported signals from a passive wireless magnetoelastic sensor implanted in a live animal.

Application of active piezoresistive cantilevers in high-eigenmode surface imaging

Abstract One of the most important limitations of the atomic force microscopy (AFM) is scanning speed, whose high values are required for contemporary high-resolution, long-range diagnostic applications. The measurement bandwidth of an AFM depends on several factors, but usually results from the time constant of the oscillating cantilever, which is correlated with its resonance frequency and quality factor. We propose a method to overcome this problem by performing the surface measurements when the cantilever is vibrating in higher eigenmodes. In this paper we demonstrate the application of active piezoresistive cantilevers operating in this mode. The active piezoresistive cantilever comprises a piezoresistive deflection sensor, a deflection actuator and a nanotip. It is a complete micro-electro-mechanical system (MEMS), ensuring the highest reliability of cantilever vibration control and detection. Higher eigenmode operations are usually difficult to implement as they usually result in lower deflection and lower sensitivity of the probe vibration deflection. Here we present an experimental modification of the structure of an active piezoresistive cantilever using focused ion beam (FIB) machining that mitigates both weaknesses. This has enabled the cantilever to scan the surface at a scanning rate of 10 lines/s with a maximum speed of 500 μm/s and a data acquisition rate of 10 kS/s, when the probe is vibrating at 380 kHz in the second eigenmode. We also describe a traceable calibration routine (based on analysis of the response of the piezoresistive detector, the output of the HeNe interferometer and precise control of the deflection actuator), together with the cantilever modification process and the development of the measurement setup. We show measurement results of dedicated calibration samples and silicon carbide crystal lattice references.&amp;#xD;

Design and analysis of flexible antenna sensor for non-invasive detection of pregnancy in bovine

This research article presents a monopole antenna-based sensor for detecting cow pregnancy through urine analysis. The proposed flexible antenna sensor is printed on denim fabric with a permittivity of 1.7 and a loss tangent of 0.002. The flexible antenna resonates at 2.4 GHz and the gain of the proposed antenna sensor is 2.016 dBi, with a corresponding efficiency of 96.8%. The antenna's dimensions are 30 × 44 × 1 mm3. The substrate region behind the inner area of the radiator ring acts as a sensing area. This substrate can absorb liquids through the sensing area, causing the dielectric properties of the substrate to change according to the dielectric constant of the fluid under test. Urea concentration in pregnant cow urine is 11.06 mg/dL and 1.39 mg/dL in non-pregnant cow urine. The proposed antenna sensor uses microwave signals to detect pregnancy in cows. The deviation in resonance frequency and quality factor are used as key parameters for detecting cow pregnancy.

Versatile Metamaterial: Exploring the Resonances of Symmetry‐Protected Modes for Multitasking Functionality

AbstractIn this work, an experimental study supported by numerical modeling that demonstrates the possibility of exciting Symmetry Protected‐Bound states In the Continuum (SP‐BICs) in a 1D silicon grating fabricated on a lithium niobate substrate is presented. bBoth transverse electric and magnetic polarization states are investigated, leading to the excitation of four quasi‐ Bound states In the Continuum (quasi‐BIC) resonances, exhibiting distinct behaviors. Under standard illumination conditions (plane of incidence perpendicular to the 1D grating lines), two of these resonances are highly sensitive to illumination conditions, while the other two resonances involving unconventional illumination directions (plane of incidence parallel to the grating lines) are more robust to the angle of incidence, but just as sensitive to external stresses in terms of resonance wavelength and quality factor. Additionally, temperature detection is experimentally demonstrated with a Sensitivity of ST = 0.81∼nm °C−1, a state‐of‐the‐art value achieved due to significant electromagnetic field enhancement inside the lithium niobate substrate at the quasi‐BIC resonance. These findings pave the way for their use in various sensing applications (such as biology, electromagnetic, and temperature sensing), as well as nonlinear applications like second harmonic generation, and electro‐ and acousto‐optic modulation.

Acoustic resonance technology and quality by design approach facilitate the development of the robust tetrandrine nano-delivery system

The aim of this study was to develop a sufficiently robust tetrandrine (Tet) nano-delivery system using acoustic resonance (AR) technology and freeze-drying technology. This system can effectively improve the solubility and dissolution properties of Tet, along with high stability and scale-up adaptability. Firstly, 54 stabilizers were screened simultaneously in a high-throughput manner with the help of AR technology to fully explore the optimal prescription space of tetrandrine nanosuspension (Tet-NS). The Plackett-Burman design was used to screen for critical variables severely affecting the quality of Tet-NS. The Box-Behnken design was used to investigate and optimize critical variables to obtain optimal nanosuspensions. The optimal prescription was successfully scaled up by 100 times, which was the initial exploration of its commercial scale production. Solidification studies have shown that formulations with 2.44% fructose as the cryoprotectant have excellent redispersibility. Compared with pure Tet, Tet in Tet-NS showed a significant increase in solubility and dissolution rate in water. Fourier transform infrared (FT-IR) demonstrated that no significant interactions occurred between the drug and excipients in Tet-NS. Powder x-ray diffraction analysis (PXRD) indicated that some of the Tet transformed into amorphous state during the preparation process. In short-term stability study, Tet-NS successfully maintained its physical stability. In summary, under the guidance of the QbD concept, this study rapidly developed Tet-NS using acoustic resonance technology, which can effectively improve the solubility and dissolution properties of Tet. During the development of Tet-NS, AR technology has demonstrated high particle size reduction capability, the ability to process multiple sets of formulations in parallel, and excellent scale-up capability. Meanwhile, the method and concept of this study are not limited to Tet, but also applicable to other poorly water-soluble drugs.

Development of nanocrystallized magnetoelastic sensors with self-biased effect and improved mass sensitivity

The growing demand for cost-effective and wireless sensing technologies requires the development of simple, efficient and optimized sensors able to accurately detecting external agents. Magnetoelastic resonators represent an alternative to the traditional sensing systems, able to combine all the previously cited factors. Several studies have focused on increasing their sensitivity, in order to make it closer to the market. The present study explores thermal treatments as a novel approach to enhance the sensitivity of magnetoelastic resonators, focusing on the positive impact of crystallization processes induced in magnetoelastic platforms. The experimental results confirm an enhancement of resonant frequency and quality factor of the magnetoelastic platforms as treatment temperature increases. Particularly, the sensor annealed at 550 °C shows an increase of the resonant frequency value of 45 % with respect to the as-quenched platform, being that increase of around 1700 % for the quality factor. In addition, the nanocrystallization induction leads to a self-biased resonance, consequence of the intrinsic magnetization resulting from the crystallization in Fe2B and FeCo phases. Further, the study shows the importance of stability in resonant frequency, emphasizing the potential of the 550 °C-annealed platform for mass sensor applications. Gold deposition experiments reveal the enhanced sensitivity of the sensor annealed at 550 °C of 40 % compared to the as-quenched sensor, as well as an increase of 38 % on its accuracy. These findings represent a significant step forward in the development of magnetoelastic-based mass sensors, highlighting the pivotal role of thermal treatments in optimizing sensitivity for practical and efficient external agents detection systems.

Deep subwavelength topological edge state in a hyperbolic medium.

Topological photonics offers the opportunity to control light propagation in a way that is robust from fabrication disorders and imperfections. However, experimental demonstrations have remained on the order of the vacuum wavelength. Theoretical proposals have shown topological edge states that can propagate robustly while embracing deep subwavelength confinement that defies diffraction limits. Here we show the experimental proof of these deep subwavelength topological edge states by implementing periodic modulation of hyperbolic phonon polaritons within a van der Waals heterostructure composed of isotopically pure hexagonal boron nitride flakes on patterned gold films. The topological edge state is confined in a subdiffraction volume of 0.021 µm3, which is four orders of magnitude smaller than the free-space excitation wavelength volume used to probe the system, while maintaining the resonance quality factor above 100. This finding can be directly extended to and hybridized with other van der Waals materials to broadened operational frequency ranges, streamline integration of diverse polaritonic materials, and compatibility with electronic and excitonic systems.

A novel microwave microfluidic sensor for purity detection of Medicines’ raw materials

A novel microwave microfluidic sensor is offered for purity detection of medicine’s raw materials which is composed of two radial components and a PDMS microfluidic holder to apply the test samples. The basis of the sensing method is the shift in the resonance frequency and quality factor of the resonator in the presence of liquids with different complex permittivity. To investigate the performance of the proposed sensor, various solvents, binary mixtures of ethanol–water, and raw materials of 3 different medicines have been checked and a 980 MHz variation of resonance frequency, which provided a very high sensitivity equal to 0.53, was achieved for a complex permittivity range of 1–78.4. The proposed sensor has a small size, simple design, easy fabrication process, and very high sensitivity while it is fabricated on an FR4 substrate which decreases the total cost significantly.

Wafer-scale fabrication of InGaP-on-insulator for nonlinear and quantum photonic applications

The development of manufacturable and scalable integrated nonlinear photonic materials is driving key technologies in diverse areas, such as high-speed communications, signal processing, sensing, and quantum information. Here, we demonstrate a nonlinear platform—InGaP-on-insulator—optimized for visible-to-telecommunication wavelength χ(2) nonlinear optical processes. In this work, we detail our 100 mm wafer-scale InGaP-on-insulator fabrication process realized via wafer bonding, optical lithography, and dry-etching techniques. The resulting wafers yield 1000 s of components in each fabrication cycle, with initial designs that include chip-to-fiber couplers, 12.5-cm-long nested spiral waveguides, and arrays of microring resonators with free-spectral ranges spanning 400–900 GHz. We demonstrate intrinsic resonator quality factors as high as 324 000 (440 000) for single-resonance (split-resonance) modes near 1550 nm corresponding to 1.56 dB/cm (1.22 dB/cm) propagation loss. We analyze the loss vs waveguide width and resonator radius to establish the operating regime for optimal 775–1550 nm phase matching. By combining the high χ(2) and χ(3) optical nonlinearity of InGaP with wafer-scale fabrication and low propagation loss, these results open promising possibilities for entangled-photon, multi-photon, and squeezed light generation.

Thin-film dielectric characterization by bound state in the continuum in high contrast grating

Subwavelength high contrast grating (HCG) is renowned for its remarkable ability to produce sharp optical resonance, known as the bound state in the continuum (BIC). Due to the strong surface field enhancement, the resonant wavelength and quality factor (Q factor) are highly sensitive to the dielectric properties of the surrounding medium. We propose utilizing this extraordinary phenomenon for thin-film dielectric characterization based on a film-substrate-grating configuration. By optimizing the geometrical parameters to control the cross-interference between guided modes in the grating and self-interference of propagating wave in the substrate slab, an accidental BIC with a Q factor reaching 104 is excited. Using this BIC, two retrieval methods based on contour mapping of resonant wavelength and Q factor are proposed to extract the complex permittivity (εf) of the film under test. It has been demonstrated that with a film thickness as thin as 10−5 times the grating period, the error in the retrieved Re[εf] is below 2%, and that of Im[εf] is below 10%. The proposed design is a strong candidate for non-destructive dielectric characterization of thin films with thicknesses below one-thousandth of the operating wavelength. This characterization technique can facilitate the development of high-frequency devices for the 6 G high-speed communication.

Electrically tunable metasurface in TN LC configuration with enhanced quality factor and metaatom-induced alignment.

Dynamic metasurface with subwavelength dimensions has emerged as a key optical technology in recent years. Although various active tuning mechanisms are being proposed, liquid crystal-based dynamic metasurface remains attractive due to its large index variation, electrical tunability, reliability, and mass fabricability. In this work, we report a dynamic metasurface for amplitude modulation in reflection, with twisted nematic liquid crystal configuration to reduce broadband reflection in the off state. The metasurface consists of coupled subwavelength grating fingers, which provide alignment for the liquid crystal without the need for an additional alignment material or process. The alignment of liquid crystal materials was examined between crossed polarizers, and the twist of nematic liquid crystal was confirmed. The coupled grating fingers exhibit a resonance quality factor of 27 at telecommunication wavelength and an amplitude modulation depth of 8 times of the minimum at 1630 nm. This work highlights the potential of liquid crystal-based tunable metasurface, combining polarization control via liquid crystal and spectrum control via metasurface. Furthermore, it also shows a way in which the interaction between liquid crystal and metasurface is used for an alignment layer-free cell assembly process.

Non-invasive optoacoustic imaging of glycogen-storage and muscle degeneration in late-onset Pompe disease

Pompe disease (PD) is a rare autosomal recessive glycogen storage disorder that causes proximal muscle weakness and loss of respiratory function. While enzyme replacement therapy (ERT) is the only effective treatment, biomarkers for disease monitoring are scarce. Following ex vivo biomarker validation in phantom studies, we apply multispectral optoacoustic tomography (MSOT), a laser- and ultrasound-based non-invasive imaging approach, in a clinical trial (NCT05083806) to image the biceps muscles of 10 late-onset PD (LOPD) patients and 10 matched healthy controls. MSOT is compared with muscle magnetic resonance imaging (MRI), ultrasound, spirometry, muscle testing and quality of life scores. Next, results are validated in an independent LOPD patient cohort from a second clinical site. Our study demonstrates that MSOT enables imaging of subcellular disease pathology with increases in glycogen/water, collagen and lipid signals, providing higher sensitivity in detecting muscle degeneration than current methods. This translational approach suggests implementation in the complex care of these rare disease patients.

Nonlinear response of very high frequency contour mode resonators

We explore the source of nonlinearities in Aluminum Nitride (AlN) Contour Mode Resonators (CMRs) operating in the Very High Frequency (VHF) range. We demonstrate that the red-shift of the resonance frequency found in VHF CMRs when the input RF power increases is due to nonlinear stiffness appearing from self-heating, and variable damping due to geometric nonlinearities. Moreover, we find a linear relationship between the variable damping coefficient and the resonator quality factor (Q). Such nonlinear mechanisms are modeled using a spring-mass-damper physical system and, in the electrical domain, a modified Butterworth-Van Dyke (MBVD) circuit where the nonlinear stiffness and variable damping are captured by a charge-dependent motional capacitor and a charge-dependent motional resistor, respectively. Detailed guidelines are provided to accurately analyze nonlinear CMRs using full-wave numerical simulations based on a finite-element method. Such simulations allow us to isolate the influence of each independent nonlinear mechanism and establish a relation between variable damping and geometric nonlinearities. Circuit and full-wave numerical simulations are in good agreement with measured data from fabricated 225 MHz CMRs exhibiting different Q. Finally, we exploit nonlinearities in high-Q CMRs to generate frequency combs at the MHz range opening the door to new exciting applications in telecommunication and sensing.

Substrate‐Free Terahertz Metamaterial Sensors With Customizable Configuration and High Performance

AbstractMetamaterials based on quasi‐bound states in the continuum (qBICs) with manipulable resonance quality (Q) factors have provided a standout platform for cutting‐edge terahertz (THz) sensing applications. However, most so far have been implemented as conventional metal patch structures with adjacent substrate layers, incurring the limitation of insufficient light‐matter interaction due to substrate effects. Here, qBIC‐driven metamaterials with substrate‐free metallic aperture structures for tailoring light‐matter interactions and exhibiting near‐ideal sensing performance is introduced. Specifically, it is incorporated ultrafast femtosecond laser processing technology to fabricate H‐type metallic aperture metamaterials with accessible high‐contrast Q factor resonances allowed by in‐plane symmetry breaking. Correspondingly, stronger light field energies are applied to the interactions due to completely eliminating the confinement of the substrate effect, enabling experimental sensitivity of up to 0.86 THz RIU−1 for the qBIC resonance, 1.9 times that of the conventional dipole resonance. Moreover, a high Q qBIC resonance achieved by optimized asymmetry parameter is exploited for detecting ultrathin layers of L‐proline molecules as low as 0.87 nmol. It is envisioned that this approach will deliver insights for real‐time, precise, and high‐performance detection of trace biomolecules, and open new perspectives for realizing ideal performance metadevices.

Second harmonic generation enhancement based on quasi-BICs in centrosymmetric materials

In centrosymmetric optical materials, the second-order nonlinear polarization of the bulk electric dipolar contribution is zero. More effective utilization of the contribution of the surface term is one of the key methods to efficiently obtain second-order nonlinear responses on these materials. Herein, a design of densely packed slotted nanopillar arrays based on quasi-bound states in the continuum (quasi-BICs) is proposed. The quasi-BICs are analyzed by using the finite element method as an example of silicon and the second harmonic generation (SHG) process is simulated. In the structure, normal-incidence linearly polarized light excites magnetic dipole-like quasi-BICs with a high quality factor which effectively promotes light-matter interactions. Increasing the nanopillar radius or decreasing the lattice constant within a certain range can cause the distribution of quality factors in k-space of the ky direction to contract toward the Γ point, which leads to a quasi-BIC with higher quality factors at the Γ point. By conjunctively adjusting the nanopillar radius and lattice constant or changing the slot azimuth, the resonance wavelength can be adjusted over a wide range (about several hundred nanometers) or finely (within about one nanometer) while maintaining high quality factors. When the symmetry perturbation introduced by the slot is small, it is calculated that the SHG conversion efficiency is about 10−6∼10−5 at an incident light power density of 1 MW/m2, and the SHG power is about 107∼108 times enhancement compared with the structure without slots. As the slot width decreases, higher SHG conversion efficiency with more significant SHG enhancement can be achieved at a specific slot length. The results provide new insights into the modulation of the resonant wavelength and quality factor of quasi-BICs, as well as the control of second-order nonlinear effects in centrosymmetric materials.

Loss and decoherence in superconducting circuits on silicon: Insights from electron spin resonance

Solid-state devices used for quantum computation and quantum sensing applications are adversely affected by loss and noise caused by spurious, charged two-level systems (TLS) and stray paramagnetic spins. These two sources of noise are interconnected, exacerbating the impact on circuit performance. We use an on-chip electron spin resonance (ESR) technique, with niobium nitride (NbN) superconducting resonators, to study surface spins on silicon and the effect of postfabrication surface treatments. We identify two distinct spin species that are characterized by different spin-relaxation times and respond selectively to various surface treatments (annealing and hydrofluoric acid). Only one of the two spin species has a significant impact on the TLS-limited resonator quality factor at low-power (near-single-photon) excitation. We observe a three- to fivefold reduction in the total density of spins after surface treatments and demonstrate the efficacy of ESR spectroscopy in developing strategies to mitigate loss and decoherence in quantum systems. Published by the American Physical Society 2024

Exploring the relationship between deposition method, microstructure, and performance of Nb/Si-based superconducting coplanar waveguide resonators

Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. In this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.

Super-resolution deep learning reconstruction approach for enhanced visualization in lumbar spine MR bone imaging

ObjectivesThis study aims to assess the effectiveness of super-resolution deep-learning-based reconstruction (SR-DLR), which leverages k-space data, on the image quality of lumbar spine magnetic resonance (MR) bone imaging using a 3D multi-echo in-phase sequence. Materials and methodsIn this retrospective study, 29 patients who underwent lumbar spine MRI, including an MR bone imaging sequence between January and April 2023, were analyzed. Images were reconstructed with and without SR-DLR (Matrix sizes: 960 × 960 and 320 × 320, respectively). The signal-to-noise ratio (SNR) of the vertebral body and spinal canal and the contrast and contrast-to-noise ratio (CNR) between the vertebral body and spinal canal were quantitatively evaluated. Furthermore, the slope at half-peak points of the profile curve drawn across the posterior border of the vertebral body was calculated. Two radiologists independently assessed image noise, contrast, artifacts, sharpness, and overall image quality of both image types using a 4-point scale. Interobserver agreement was evaluated using weighted kappa coefficients, and quantitative and qualitative scores were compared via the Wilcoxon signed-rank test. ResultsSNRs of the vertebral body and spinal canal were notably improved in images with SR-DLR (p < 0.001). Contrast and CNR were significantly enhanced with SR-DLR compared to those without SR-DLR (p = 0.023 and p = 0.022, respectively). The slope of the profile curve at half-peak points across the posterior border of the vertebral body and spinal canal was markedly higher with SR-DLR (p < 0.001). Qualitative scores (noise: p < 0.001, contrast: p < 0.001, artifact p = 0.042, sharpness: p < 0.001, overall image quality: p < 0.001) were superior in images with SR-DLR compared to those without. Kappa analysis indicated moderate to good agreement (noise: κ = 0.56, contrast: κ = 0.51, artifact: κ = 0.46, sharpness: κ = 0.76, overall image quality: κ = 0.44). ConclusionSR-DLR, which is based on k-space data, has the potential to enhance the image quality of lumbar spine MR bone imaging utilizing a 3D gradient echo in-phase sequence.Clinical relevance statement: The application of SR-DLR can lead to improvements in lumbar spine MR bone imaging quality.