Representation Of Vibration Signals Research Articles

Visualized Stacked Denoising Auto-Encoder Model for Extracting and Evaluating the State Features of Rolling Bearings

Extracting intuitive operating state features from vibration signals without prior knowledge is a prospective requirement for health monitoring and fault diagnosis in bearings. In this paper, a visualized stacked denoising auto-encoder (VSDAE) model is proposed for the unsupervised extraction and quantitative evaluation of bearings’ state features. First, the stacked denoising auto-encoder (SDAE) was used to reconstruct vibration signals. The intermediate vector of the SDAE, which is a high-information-density representation of vibration signals, was regarded as the pending state feature. Then, the dimension of the intermediate vector was reduced by the t-distributed stochastic neighbor embedding (t-SNE) method to the two-dimensional visualization space. Finally, the silhouette coefficient of feature distribution was calculated to quantitatively evaluate the extracted features. The proposed model was evaluated using experimental bearing signals simulating various operating states. The results proved that the features, extracted and evaluated by the VSDAE, allowed the recognition of the operating states of the examined bearings.

Deep transfer learning-based vehicle classification by asphalt pavement vibration

Deep transfer learning (TL) has great potential for a wide range of applications in civil engineering. This work aims to propose a deep transfer learning-based method for vehicle classification by asphalt pavement vibration. This work first used the pavement vibration IoT monitoring system to collect raw vibration signals and performed the wavelet transform to obtain denoised vibration signals. The vibration signals were then represented in two different ways, including the time-domain graph and the time-frequency graph. Finally, two deep transfer learning-based methods, namely Method Ⅰ (Time-domain & TL) and Method Ⅱ (Time-frequency & TL), were applied for vehicle classification according to the two different representations of vibration signals. The results show that the CNN model had a satisfactory performance in both methods with the accuracy of Method Ⅰ exceeding 0.94 and Method Ⅱ exceeding 0.95. The CNN model in Method Ⅱ performed better in the accuracy metrics with considering label imbalance, but worse in the accuracy metrics without considering label imbalance than that in Method Ⅰ. The differences between these two methods have been investigated and discussed in detail in terms of input types, accuracy metrics, and application prospects. The CNN model with deep transfer learning could be an effective, accurate, and reliable technique for vehicle classification based on asphalt pavement vibration.

Bearing fault diagnosis based on spectrum image sparse representation of vibration signal

Bearings are crucial for industrial production and susceptible to malfunction in rotating machines. Image analysis can give a comprehensive description of vibration signal, thus, it has achieved much more attention recently in fault diagnosis field. However, it brings lots of redundant information from a single spectrum image matrix behind rich fault information, and massive spectrum image samples lead to exacerbation of this situation, which readily results in the accuracy-dropping problem of multiple local defective bearings diagnosis. To solve this issue, a novel feature extraction method based on image sparse representation is proposed. Original spectrum images are acquired through fast Fourier transformation. Sparse coefficient that reveals the underlying structure of spectrum image based on raw signals is extracted as the feature by implementing the orthogonal matching pursuit and K-singular value decomposition algorithm strategically, and then two-dimensional principal component analysis is applied for further processing of these features. Finally, fault types are identified based on a minimum distance strategy. The experimental results are given to demonstrate the effectiveness of the proposed method.

Nonnegative Matrix Factorization of time frequency representation of vibration signal for local damage detection – comparison of algorithms

Local damage detection in rotating machine elements is very important problem widely researched in the literature. One of the most common approaches is the vibration signal analysis. Since time domain processing is often insufficient, other representations are frequently favored. One of the most common one is time-frequency representation hence authors propose to separate internal processes occurring in the vibration signal by spectrogram matrix factorization. In order to achieve this, it is proposed to use the approach of Nonnegative Matrix Factorization (NMF). In this paper three NMF algorithms are tested using real and simulated data describing single-channel vibration signal acquired on damaged rolling bearing operating in drive pulley in belt conveyor driving station. Results are compared with filtration using Spectral Kurtosis, which is currently recognized as classical method for impulsive information extraction, to verify the validity of presented methodology.

Bearings Fault Diagnosis Based on Convolutional Neural Networks with 2-D Representation of Vibration Signals as Input

Periodic vibration signals captured by the accelerometers carry rich information for bearing fault diagnosis. Existing methods mostly rely on hand-crafted time-consuming preprocessing of data to acquire suitable features. In this paper, we use an easy and effective method to transform the 1-D temporal vibration signal into a 2-D image. With the signal image, convolutional Neural Network (CNN) is used to train the raw vibration data. As powerful feature extractor and classifier for image recognition, CNN can learn to acquire features most suitable for the classification task by being trained. With the image format of vibration signals, the neuron in fully-connected layer of CNN can see farther and capture the periodic feature of signals. According to the results of the experiments, when fed in enough training samples, the proposed method outperforms other common methods. The proposed method can also be applied to solve intelligent diagnosis problems of other machine systems.