Nitrogen Release Characteristics Research Articles

Evaluation of Nitrogen Release Characteristics and Enhanced Efficiency of a Novel Synthetic Slow-Release Nitrogen Fertilizer

Evaluation of Nitrogen Release Characteristics and Enhanced Efficiency of a Novel Synthetic Slow-Release Nitrogen Fertilizer

Effect of Potassium Ferrate as a Dewatering Conditioner on Sludge Pyrolysis Characteristics and the Releasing Characteristics of Nitrogen, Sulfur, and Chlorine during Sewage Sludge Pyrolysis

Sludge pyrolysis is a promising method for treating excess sludge as a by-product of municipal sewage plants, allowing for energy self-sufficiency and resource recovery. Before sludge pyrolysis begins, a few conditioning agents are added to the sludge that promote sludge dewatering. Potassium ferrate (K2FeO4) is applied as a conditioning agent with both cracking and flocculation effects, but the effects of K2FeO4 on the release characteristics of nitrogen, sulfur, and chlorine during sludge pyrolysis have not been elucidated. In this study, we analyzed the sludge pyrolysis characteristics and chemical state changes of N, S, and Cl contaminants in the dewatered sludge after K2FeO4 conditioning before and after pyrolysis. Further, the release characteristics of condensable/noncondensable gases during pyrolysis were assessed using thermogravimetric mass spectrometry (TG-MS) and pyrolysis–gas chromatography/mass spectrometry (Py-GC/MS) analyses before and after conditioning. We found that potassium pertechnetate reduced the activation energy required for the sludge in the pyrolysis process. Noticeably this process made the sludge more susceptible to thermal decomposition leading to volatile production and also influenced the release of different contaminants generated by the pyrolysis process. Moreover, K2FeO4 promoted the release of C/H/O gases and reduced the release of N/S/Cl pollutant gases from the sludge. Overall, this study provides a theoretical basis for the selection of conditioning agents for the sludge conditioning and dewatering steps during the sludge pyrolysis process.

Release of nitrogen during thermochemical conversion of Shenhua bituminous coal under Ar, CO2, and air atmospheres

AbstractCoal thermochemical conversion processes unavoidably generate gaseous pollutants, endangering the environment or influencing synthetic processes downstream. In order to display the differences in release behaviours of nitrogen among different coal thermochemical conversion stages, the nitrogen release characteristics of Shenhua bituminous coal under Ar, CO2, and air atmospheres were investigated using X‐ray photoelectron spectrum (XPS) and thermogravimetry‐mass spectrometry (TG‐MS). Results indicate that the reaction atmosphere has an important influence on nitrogen release. The total released mass of nitrogen when using 100 g raw coal in the whole experiment under Ar, CO2, and air atmospheres is 0.54, 0.64, and 0.75 g, respectively. The organic forms of nitrogen in raw coal and coal char are pyridine nitrogen (N‐6), pyrrole nitrogen (N‐5), quaternary nitrogen (N‐Q), and nitrogen oxide (N‐X). While in the coal ash, the sub‐peaks of N‐Q and N‐X disappear entirely, leaving only N‐5 and N‐6 sub‐peaks. The released nitrogen‐containing gas consists of NH3, HCN, NO, and NO2 during experiments in CO2 and air atmospheres. However, only NH3 and HCN are detected during experiments in the Ar atmosphere. The revolution characteristics of NH3 and HCN under Ar and CO2 atmospheres are similar.

Pollution and Release Characteristics of Nitrogen, Phosphorus and Organic Carbon in Pond Sediments in a Typical Polder Area of the Lake Taihu Basin

There is currently a lack of knowledge on the release characteristics of nutrients from artificial pond sediments in polder areas, resulting in problems in future management of such environments, including converting polders to lakes. In this study, sediment samples were taken from a fish pond and a lotus pond in a typical polder area of the Lake Taihu Basin in China. The total nitrogen (TN, 1760–1810 mg/kg), total phosphorus (TP, 1370–1463 mg/kg) and total organic carbon (TOC, 10.1–21.2 g/kg) contents were significantly higher than those found in sediments from the adjacent aquatic system, which indicates that the legacy of agricultural activities has had an obvious cumulative effect on pond sediment nutrients. The release behavior of TN, TP and TOC varied significantly, not only under disturbed and static conditions, but also from sediments sampled at different ponds and depths. During the disturbing condition, there were continuous releases of carbon and nutrients in the lotus pond sediments, while the fish pond sediments showed a higher release at the beginning. Under static release conditions, the release of TP in the surface and bottom sediments of the fish pond increased first, then decreased and stabilized within 24 h, while the release of the lotus pond showed a slow upward trend. Despite the lower concentration of nutrients and TOC, the lotus pond sediment showed a higher release rate. The results suggested that it is necessary to adopt different strategies for different types of ponds in the project of returning polders to lakes; it is especially important to pay attention to the release of nutrients from the bottom sediments of lotus ponds in the project management.

牲畜排泄物返还对草地土壤氮转化和氧化亚氮(N2O)排放的影响研究进展

牲畜排泄物返还被认为是对草地的一种天然的施肥措施，也是草地养分归还的一种重要途径，对于维持土壤肥力和植被生产力具有十分重要的生态学意义。论述了放牧牲畜粪便和尿液自身降解及其氮素变化、粪尿返还对草地土壤氮转化和氧化亚氮（N₂O）排放的作用机制及影响效应，指出排泄物氮输入使粪尿斑块成为草地土壤氮转化和N₂O排放的活跃点，且不同排泄物类型、土壤理化特性和气候条件等使土壤氮素矿化、固持、硝化及反硝化等关键过程具有复杂性和差异性，进而导致不同类型草地生态系统N₂O排放对牲畜排泄物返还的响应不尽相同。建议未来在全球气候变化背景下，应加强草地牲畜排泄物-植被-土壤体系氮素生物地球化学循环过程的系统研究，进一步加深天然草地关键氮素转化过程和N₂O排放的微生物作用机制方面的认识，从而有助于为优化放牧牲畜排泄物的管理模式、制定科学合理的草地土壤养分调控策略和维持草地生态系统可持续发展提供科学有效的理论指导。;Livestock excreta deposition is considered as a natural fertilization measure in grassland and also an important pathway for the return of grassland nutrients, which may generate greatly ecological significance for the maintenance of soil fertility and vegetation productivity. In this study, we systematically elaborated the variation of nitrogen embedded within grazing livestock dung and urine patches during its natural decomposition, so as to investigate the possible functional mechanisms and influential effects of livestock dung and urine application on soil nitrogen transformation process and nitrous oxide (N₂O) emission. Results showed that livestock excreta nitrogen input made the grassland area covered by dung and urine to become an active point for soil nitrogen transformation and N₂O emission. Generally speaking, the degradation rate of livestock dung was slow and its nitrogen release usually lasts for a long time, which may generate a series of effects on the soil nitrogen transformation and N₂O emission in the natural grassland. On the contrary, livestock urine deposition would rapidly increase soil mineralized nitrogen content in a short period of time, thus may generate a certain of priming effect on nitrogen dynamic and its form transformation in soil profiles, which probably deeply change the soil available nitrogen contents and the microenvironment that related to N₂O emission. It is worth noting that the differences in dung and urine patch shape, physicochemical properties, degradation and nitrogen release characteristics would inevitably alter the soil redox condition, nitrogen content and its form features of grassland soil profiles in different degrees, which may cause the complicated temporal-spatial response of soil nitrogen migration and transformation processes and the microbial functional mechanism differences in N₂O generation and emission. In addition, the differences in excreta types, soil physicochemical properties, and climatic conditions would complicatedly influence the major processes of soil nitrogen mineralization, immobilization, nitrification and denitrification, and therefore resulted in differential response of N₂O emission in different grassland ecosystems. Scientific suggestions were put forward that more attentions should be paid to strengthening the systematic research on the nitrogen biogeochemical cycling in the faecal-vegetation-soil system of grassland under the background of climate change, in order to deeply improve the theoretical understanding of major nitrogen transformation process and microbial mechanism of N₂O production and emission in the natural grassland. The results would provide scientific and theoretical guidance for optimizing livestock excreta management models, and formulating reasonable regulation strategies of grassland soil nutrients, so as to maintain the sustainable development of grassland ecosystems.

Geochemical Fractions and Release Characteristics of Nitrogen in Sediments Along Deep-Water Cascade Reservoirs of the Lancang River

The effect of dams on the longitudinal variability, characteristics, and release mechanism of different nitrogen fractions is unknown along with canyon cascade reservoirs. In this study, we analyze...

Release Mechanisms of Carbon Source and Dissolved Organic Matter of Six Agricultural Wastes in the Initial Stage

As carbon sources for the denitrification process, agricultural wastes have some problems, such as excess release of organic carbon; unclear release characteristics of nitrogen, phosphorus, and colorimetric substances; and unclear components, release mechanisms, and potential effects of the released dissolved organic matter (DOM) in the start-up period. To resolve those problems, rice straw, wheat straw, corn stalk, corncob, soybean stalk, and soybean hull were selected as denitrification carbon sources to investigate the release mechanisms and potential influences of the organic matter, secondary pollutants, and DOM. The results showed that the six agricultural wastes could be used as the denitrification carbon source. The carbon content in the wheat straw was the highest and the secondary pollution risk from the corncob was the lowest. For the six carbon sources, the second-order kinetic equation and Ritger-Peppas equation were followed during the 1-120 h carbon release process. The fitting results demonstrated that corncob was more suitable for use as the denitrification carbon source because of its moderate cm value and longer t1/2 value, and the release mechanisms of the six types of carbon sources were mainly controlled by the diffusion process. The NH4+-N, TN, and TP contents in the immersion water of the rice straw were higher than those of the five other agricultural wastes, and there was heavy chromaticity in the immersion water of the wheat straw and corn stalk. The amounts of nitrogen, phosphorus, and chromatic substances released from the corncob were the lowest. The leachates of the corncob and soybean hull had higher biodegradability and lower risks of secondary pollution than those of the other sources. The aromaticity and molecular weight of DOM increased as the reaction time increased, and the humification of DOM was low. Five components were identified by PARAFAC. The main component was protein-like matter, which was mainly composed of tyrosine-like and tryptophan-like substances. There was less humic acid-like matter in the immersion water. The component characteristics of DOM might have had an adverse effect on the subsequent water treatment process. These results could provide theoretical support for the impact on effluent water quality and risk assessment when the agricultural wastes are used as an additional denitrification carbon source at the start-up stage.

Twice-split application of controlled-release nitrogen fertilizer met the nitrogen demand of winter wheat

As a new long-acting fertilizer, controlled-release nitrogen fertilizer (CRNF) has been shown to increase crop yield and improve nitrogen use efficiency (NUE) of fertilizer in many production systems. However, due to the limitation of nutrient release longevity of CRNF and the nitrogen demand characteristics of winter wheat (Triticum aestivum L.), further study is needed on the appropriate application technology of CRNF. In the present study, using polymer-coated urea (PCU) and sulfur-coated urea (SCU) as materials, the characteristics of nitrogen release from one-time or twice-split application of CRNF and its effect on the nitrogen uptake and growth of wheat were investigated in a two-year field experiment. The results indicated that nitrogen release from the twice-split application of PCU and SCU was synchronized with the nitrogen demand of wheat at different stages. Compared with urea multiple-split application (CK) and CRNF one-time application (PCU1 and SCU1), CRNF applied twice, at pre-sowing and re-greening (PCU2 and SCU2), maintained a high level of soil inorganic nitrogen after jointing, which met the second peak demand for nitrogen and improved the nitrogen uptake of wheat. Both PCU2 and SCU2 were found to be beneficial in delaying the senescence of leaves and the decline of photosynthetic performance after anthesis, which significantly increased the accumulation of post-anthesis dry matter and significantly affected the grain yield, with an increase of 9.96–15.11 % compared with multiple-split application of urea. PCU2 and SCU2 also improved NUE by 6.71–10.33 %. The results of this study demonstrate that CRNF applied twice was a good fertilization method for synchronizing nitrogen release from fertilizer and the nitrogen demand of wheat, thus improving wheat yield and NUE and decreasing the labor required for fertilizer application.

Release Mechanism, Secondary Pollutants and Denitrification Performance Comparison of Six Kinds of Agricultural Wastes as Solid Carbon Sources for Nitrate Removal.

Agricultural wastes used as denitrification carbon sources have some drawbacks such as excessive organic carbon release and unclear release characteristics of nitrogen, phosphorus, and chromatic substances, which can cause adverse effects on the effluent quality during the denitrification process. The composition and surface characteristics, carbon release mechanisms, and secondary pollutant release properties of six kinds of agricultural wastes, i.e., rice straw (RS), wheat straw (WS), corn stalk (CS), corncob (CC), soybean stalk (SS), and soybean hull (SH) were studied and analyzed in this research. The denitrification performance of these agricultural wastes was also investigated extensively by batch experiments. The results showed that the carbon release basically followed the second-order reaction kinetic equation and Ritger–Peppas equation in the 120 h reaction, and it was mainly controlled by the diffusion process. The kinetic equation fitting results and bioavailability test suggested that the potential risk of excessive effluent COD of CC was the lowest due to the appropriate amount and degradability of its released carbon. The NH4+-N, TN, and TP in the leachate of RS were higher than those of the other five agriculture wastes, and the chroma in the leachate of WS and CS was heavier than that of the others. CC released the lowest pollutants, which resulted in slight fluctuations of effluent quality in the start-up period (1–11 d), and it had the best nitrogen removal capacity in the denitrification experiment. The average NO3−-N removal of CC was 5.12 mg for each batch in the stable period (11–27 d), which was higher than that of others, and less NO2−-N, NH4+-N, and COD were accumulated in the CC effluent during the whole denitrification process.

Preparation of biochar as a coating material for biochar-coated urea

Biochar was used as a coating material for slow release urea. However, influence of biochar performance on preparing biochar-coated urea (BCU) and nitrogen release characteristics is rarely reported. In this study, total of 24 biochars were prepared and characterized from six biomass residues (rice straw, chicken manure, vinasse, Phyllostachys pubescens, Arundo donax and sugarcane bagasse) at four pyrolysis temperatures (400–700 °C). Grey correlation analysis (GCA) was used to select biochar as a coating material for BCU based on biochar performance indicators. The feasibility (BCU formability) for preparing BCU and characteristics of nitrogen release in BCU based on hydrostatic dissolution test and soil column leaching experiment were evaluated. Biochar prepared at low pyrolysis temperature was not suitable as a coating material for BCU due to low specific surface area. Biochars derived from pyrolysis of Phyllostachys pubescens (BP6), vinasse (BV6) and rice straw (BR6) at 600 °C were selected as coating materials for BCU based on grey correlation analysis (GCA). The adhesion of biochar to urea surface was related to biomass type that preparing biochar. BV6 was recommended for use as coating material for BCU because the feasibility of the biochars followed the order BR6 > BV6 > BP6, and the practicality of the biochars followed the order BP6 > BV6 > BR6. The findings suggest that biochar with a high specific surface area, hydrophilic oxygen-containing functional groups and low pH is a suitable material for BCU.

Nitrogen Release Characteristics of a Bag Controlled Release Fertilizer

Slow release fertilizers are designed to enhance crop yield and minimizing the loss of nitrogen (N) to environment. However, N release in leaching and loss in ammonia emission from bag controlled release fertilizers have not been previously evaluated under the standardized conditions in soil. Accordingly, a laboratory study was conducted to evaluate the characteristics of N release from a bag controlled fertilizer with 1, 3, 5 and 7 rows of hole (B-1, B-3, B-5, B-7) and a kraft bag without hole (B-W). The results showed that the amount of N leaching of B-1, B-3, B-5, B-7 and B-W were significantly lower than urea fertilizer without bag (U). The maximum N release from the fertilizers followed the order: U (83.16%) > B-7 (54.61%) > B-5 (54.02%) > B-W (51.51%) > B-3 (48.87%) > B-1 (38.60%) during the experimentation. Compared with U treatment, ammonia volatilization losses were significantly decreased by B-1, B-3, B-5, B-7 and B-W treatments. Based on N release and loss, a suitable bag with holes should be considered in practice when using the bag controlled fertilizer to meet an environment good objective. The evaluation method merits further study combined with field experiment.

Carbonaceous microsphere‐based superabsorbent polymer as filler for coating of NPK fertilizer: Fabrication, properties, swelling, and nitrogen release characteristics

ABSTRACTRecently, the use of controlled release fertilizers in agriculture has resulted in huge benefits in plant growth and cultivation. Superabsorbent polymer (SAP)‐coated fertilizers have the added advantage in retaining water in soil after irrigation and also reduce the nutrient release rate from soil in a controlled manner. This study aimed to produce a nitrogen–phosphorus–potassium (NPK) fertilizer coated with superabsorbent carbonaceous microspheres polymer (SPC) by inverse suspension polymerization method with water‐retention and controlled release properties. Two sets of experiments were conducted: (1) three different weight percentages and (2) different materials. NPK coated with SPC showed increasing water‐retention ability with respect to carbon microsphere percentages and retains >80% water at the 30th day of experiment compared with pure NPK and NPK coated with SAP. The slow release behavior of all samples was investigated by induced coupled plasma mass spectrometry spectrometry and results showed that NPK coated with SAP and SPC has a low release rate with <50% nutrient release compared with uncoated NPK at the 30th day. The release mechanism kinetics of NPK coated with SAP and SPC were studied based on the Kosmeyer–Peppas model. The mechanisms approached Fickian diffusion‐controlled release as the n value for both samples was less than 0.5. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48396.

Decomposition of Myriophyllum aquaticum and the Associated Release of Nitrogen and Phosphorus

Decomposition of wetland plants could release pollutants, which may affect the removal efficiency and effluent quality of constructed wetlands. The experimental decomposition test of Myriophyllum aquaticum was carried out for 60 d using nylon bags, and release characteristics of nitrogen and phosphorus during the decomposition process were studied. The results showed that the decomposition rate of M. aquaticum was fastest during the first 0-4 d, with a weight loss of 30%, while the degradation rate slowed gradually during the period 4-60 d, with weight loss of 31%. The fitting first-order kinetic decomposition rate constant was 0.0142 d-1, and the calculated time to degrade 50% of dry matter was 48.8 d. The water pH decreased rapidly from 7.60 to 5.63 during 0-4 d, stabilized during 4-32 d, and finally increased to 7.03 (which was close to the control sample without M. aquaticum). The dissolved oxygen concentration decreased rapidly from 6.30 mg·L-1 to 0.61 mg·L-1 during 0-4 d, and remained in an anaerobic state. The total nitrogen concentration in the water increased rapidly to 12.7 mg·L-1 within 2 h, gradually decreased to 5.80 mg·L-1 during 2 h-32 d, and then finally increased slightly. The phosphorus concentration increased rapidly to 18.4 mg·L-1 at the beginning of the experiment, and then gradually stabilized. The main forms of nitrogen and phosphorus released by M. aquaticum were organic nitrogen (accounting for 65.7%-94.7% of total nitrogen) and inorganic phosphorus (accounting for 61%-89% of total phosphorus), respectively. The total nitrogen content of M. aquaticum increased from 24.3 mg·g-1 to 60.5 mg·g-1 with increasing degradation time; the total phosphorus decreased initially from 6.09 mg·g-1 to 2.94 mg·g-1 and then remained constant. These trends may have been related to the fixation of nitrogen by attached microorganisms. Therefore, suitable harvesting and management strategies should be adopted for wetland plants to reduce secondary pollution.

The characteristics of decomposition and nutrient release of Vicia villosa under different fertilization treatments.

The effects of three fertilization treatments (no fertilizer, nitrogen fertilizer, and lime) on the characteristics of Vicia villosa decomposition and nutrient release were studied using the nylon bag method in the fields. The results showed that the cumulative decomposition rate of V. villosa was 65.3%-72.5% across the three fertilization treatments. V. villosa decomposed rapidly during 0-11 d, then slowed down and tended to be stable. The nutrient release rates across the three treatments were potassium > phosphorus > carbon > nitrogen. At the end of the experiment (148 d), the cumulative release rates of carbon, nitrogen, phosphorus and potassium were 83.6%-84.6%, 78.2%-81.2%, 89.8%-91.4% and 96.3%-97.0%, respectively. During the whole decomposition period, the characteristics of nitrogen release and decomposition of V. villosa were similar. Compared with no fertilizer treatment, lime application promoted decomposition and release of nitrogen, phosphorus and potassium. Nitrogen fertilizer application promoted phosphorus release but inhibited potassium release. Both nitrogen application and lime application had no significant effect on carbon release. The application of nitrogen fertilizer promoted the decomposition of V. villosa and nitrogen release in 0-11 d, but inhibited those processes in 11-148 d. The first-order kinetic reaction equation and logarithmic function equation well fitted the characteristics of V. villosa decomposition and the release of carbon, nitrogen, phosphorus and potassium in the rice fields of South Henan. The characteristic parameters of the equation were significantly correlated with the decomposition rate and nutrient release rate of V. villosa. In summary, lime application was better than nitrogen fertili-zer in promoting decomposition and nutrient release of V. villosa. Moreover, the parameters of the first-order kinetic equation and logarithmic function equation showed a good description of decomposition and nutrient release of V. villosa.

Release characteristics of nitrogen and phosphorus from sediments formed under different supplemental water sources in Xi'an moat, China.

The endogenous release of nutrients from sediments contributes to the eutrophication of landscape water to a certain degree, which depends on the characteristics of sediments. The study explored the characteristics of nitrogen (N) and phosphorus (P) released from two different sediments, which were deposited from reclaimed water (SRW) or surface water (SSW) respectively in Xi'an moat. This paper aimed to compare the effects of nutrient release from SRW and SSW on the water quality. Results showed that the maximum increase rates reached 1.21mg TN/(L·day) and 0.11mg TP/(L·day), respectively, in the overlying water of SRW, which were 1.6 and 2.8 times those of SSW. The released amounts of SRW were 0.192mg TN/g and 0.038mg TP/g, which were 4.1 and 12.7 times those of SSW. Meanwhile, the densities of benthic algae in SRW and SSW were 5.605 × 109 and 2.846 × 108 cells/L, respectively. Moreover, the species number and individual sizes of benthic algae in SRW were also larger than those in SSW, which played an important role in the nitrogen circulation. Unexpectedly, oxidation reduction potential (ORP) level of SRW was lower than that of SSW, although SRW has a higher dissolved oxygen level. Therefore, the N and P concentrations in the overlying water of SRW were considerably higher than those of SSW, which was mainly attributed to the higher nutrient contents and lower ORP in SRW.

Influence of Nitzschia sp. on release of nitrogen and phosphorus from sediment in pond breeding sea cucumbers

Due to the tonic and nutritive virtues of sea cucumbers, increased commercial aquaculture has resulted in the expansion of breeding ponds, a primary form of sea cucumber production. Expansion of such production methods has led to increased settling of organic wastes onto the seabed, resulting in enriched sediments. Nitzschia sp. serves as an edible sea cucumber feed. Release characteristics of nitrogen (N) and phosphorus (P) from sediments in the presence of different biomass densities of Nitzschia sp. were studied via laboratory static cultures. pH and dissolved oxygen (DO) in the overlying water and biochemical components (i.e., protein, chlorophyll a) of Nitzschia sp. were assessed. When the biomass of Nitzschia sp. was more than (2–5) × 104 ind/cm2, the release of N and P nutrients was significantly promoted; additionally, the DO content of the overlying water was relatively high and the pH was relatively stable, which favoured the accumulation of proteins and chlorophyll a in Nitzschia sp. The results indicated that Nitzschia sp. promotes the release of N and P in sediments while absorbing them to maintain their own growth and promote the accumulation of nutrients, such as proteins, for the sea cucumbers. At the same time, the algae release oxygen, increasing the DO of the overlying water, providing a healthy breeding environment for the sea cucumbers. Application of Nitzschia sp. has the potential to reduce environmental harm caused by sea cucumber cultivation and thus achieve sustainable aquaculture.

Bio-based elastic polyurethane for controlled-release urea fertilizer: Fabrication, properties, swelling and nitrogen release characteristics

A novel bio-based elastic polyurethane coated urea fertilizer (ECU) was successfully developed using low-cost, biodegradable, and renewable waste palm oil. The process utilized acrylonitrile modification to grant the ECU with excellent swollen capacity. The modified green bio-based polyurethane (PU) coating efficiently delayed the nutrient release. Herein coating shell's swollen capacity and nutrient controlled-release behaviors of the normal bio-based PU-coated urea fertilizer (PCU) and ECU in water were investigated. The results showed acrylonitrile modified bio-based polyurethane successfully transformed it into coated controlled-release urea fertilizer with excellent agricultural properties. Nutrient released longevity of ECU reached more than 80 days while that of PCU was only about 50 days. The novel synthesis and innovative application of bio-based elastic material in this study will provide not only theoretical bases but also practical guidelines for research and development of high-efficiency and environmentally friendly controlled-release fertilizer.

Parametric study of tumbling fluidized bed to evaluate nitrogen release characteristics of biopolymer-coated controlled release urea

ABSTRACTTo impede nitrogen loss due to leaching and NH3 volatilization, pristine urea particles are coated with synthetic polymers such as poly(acrylic acid) and polyethylene for the controlled release of nitrogen. However, due to nonbiodegradability and environmental and economic issues, these synthetic polymers are replaced with cheap, biodegradable, and green coating materials. In this study, borax-modified starch biopolymer is used to produce controlled release urea (CRU) in a tumbling fluidized bed. Central composite rotatable design is used to study the interactive effect of process parameters on time and kinetics of nitrogen release. Nitrogen release in distilled water is monitored by the UV–Vis spectrophotometer and soil burial test is used to observe release in soil. The optimum values of process parameters and response objectives generated by the analysis of variance are validated by triplicates of confirmation runs and the % error is reported as a precision indicator. A mathematical model is used to determine the diffusion coefficient of nitrogen release. Biopolymer-coated urea results in much better release performance when compared with starch-based CRU reported in the literature. The most influential process parameter both for time and kinetics of nitrogen release appears to be the coating time. Release time increases linearly with coating time and the diffusion coefficient decreases with increase in coating time. The kinetic study reveals that some of the samples followed non-Fickian diffusion and others followed Case-II transport during the release of nitrogen.

Characteristics of Nitrogen Release at the Sediment-Water Interface in the Typical Tributaries of the Three Gorges Reservoir During the Sensitive Period in Spring

Overlying water and sediment interstitial water samples were acquired to study the nitrogen release between sediments and water interfaces in Xiangxi Bay in April 2016 during the Sensitive Period in spring. The spatial distribution of different forms of nitrogen in the sediment was analyzed, the diffusion fluxes of different forms of nitrogen in the sediments and water systems were also measured, and a correlation analysis with environmental factors was conducted. The results show that overlying water and sediment interstitial water ρ(TN) ranges from 1.10 to 6.90 mg·L-1 and 6.19 to 32.57 mg·L-1 respectively; indicating the nitrogen concentrations in the overlying and interstitial water of sediments have a certain variation along the process and vertically. The interstitial water nitrogen concentrations in the upstream area are higher than those in the downstream area. The interstitial water ρ(NH4+-N) in the sediment is significantly larger than that in the overlying water, but the interstitial water ρ(NO3--N) in the sediment is slightly smaller than that in the overlying water. Xiangxi Bay sediment acts as a source of NH4+-N; however, for NO3--N it is a sink. The diffusive fluxes of NH4+-N range from 2.70 to 4.72 mg·(m2·d)-1; and the diffusive fluxes of NO3--N range from -1.61 to -0.62 mg·(m2·d)-1. Nitrogen is mainly present in the form of ammonium nitrogen in the sediment of Xiangxi Bay. The ρ(NH4+-N) in the sediment ranges from 69.97-1185.97 mg·kg-1, ρ(NO3--N) ranges from 2.78-38.17 mg·kg-1, and the ρ(NH4+-N) in sediments in the surface at 0-8 cm changes with the same trend.

Application of Graphene-Oxide-Modified Polyacrylate Polymer for Controlled-Release Coated Urea

Polyacrylate polymer (PA) was modified with graphene oxide (GO) and the obtained composites were applied as coatings for controlled-release coated urea (CRU). The physicochemical properties of the different PA/GO coatings were characterized in detail and the nitrogen-release characteristics of the obtained CRU samples were determined in water at 25 °C. The experimental results revealed that addition of GO to PA reduced the swelling degree from 83.01% to 46.35% and improved its mechanical properties (the Young’s modulus was improved from 31.52 to 34.97 MPa and the glass transition temperature was increased from 4.21 to 6.11 °C), thus dramatically slowing down the cumulative nutrient release from the CRU fertilizer from 87.25% to 59.71%. These results suggest that GO enhances the properties of PA for CRU applications, which shows that GO-modified PA is a good coating material.