Reinforced Concrete Beams Research Articles

Shear behavior of reinforced concrete beams with high-strength reinforcements after high temperatures

This paper investigates the effect of steel reinforcement configured with different strengths after different high temperatures on the shear performance of the test beams, a total of 20 reinforced concrete (RC) beams, through experiments, numerical analyses and theoretical studies, in order to understand the key factors affecting the shear performance of the beams. The test revealed that the mechanical properties of concrete and steel reinforcement showed a trend of increasing and then decreasing after high temperatures. Increasing the stirrup ratio and stirrup strength can significantly improve the crack resistance and shear capacity of the beams, as well as the deformation performance of the beams. The residual shear strengths of test beams with high-strength stirrups after exposure to high temperatures are significantly greater than those of ordinary reinforced concrete beams. Specifically, the shear capacity of beams with high-strength stirrups after exposure to 800°C increased by 23.7 % compared to ordinary beams, and the mid-span deflection performance increased by 28.7 %. The stresses in the shear span region of the test beams after high temperature were more concentrated at the diagonal and the number of cracks was significantly reduced. In this paper, a simplified formula for calculating the residual shear capacity of RC beams after room and high temperatures is proposed, which can well predict the test results.

Strengthening of RC Beam with GFRP Composites in Shear N. B. Bhopale

The rehabilitation, repair and strengthening of existing reinforced concrete (RC) structures is essential due to factors such as aging, steel reinforcement corrosion, construction/design defects, increased service loads demand, seismic events, and advancements in design guidelines. Fiber-reinforced polymers (FRP) are now being recognized as a promising material for the rehabilitation of such structures, through strengthening or repairing. In buildings and bridges, RC sections are commonly found in the form of beams and girders. Shear failure of RC beams is particularly due to its sudden occurrence without warning. Therefore, the utilization of externally bonded (EB) FRP composites for shear strengthening of RC beams has gathered popularity as a structural enhancement technique, primarily due to advantages of FRP composites, such as high strength-to- weight ratio and exceptional corrosion resistance. In addition, FRP repair systems give a cost-saving choice to traditional repair methods and materials. A study was performed to analyse the shear characteristics of RC beams enhanced with continuous glass fiber-reinforced polymer (GFRP) sheets. Reinforced concrete beams externally bonded GFRP sheets subjected to failure using a symmetrical two-point concentrated static loading system. The experimental data obtained included load, deflection, and failure modes of each beam, along with the effect of the number of GFRP layers on the beams The failures observed in strengthened beams typically commence with the debonding of the FRP sheets, followed by brittle shear failure. The shear capacities of these beams were higher than that of the control beam.

Experimental Study on Shear Strengthening of Reinforced Concrete Beams by Fabric-Reinforced Cementitious Matrix.

In this study, an experiment was conducted to investigate the shear performance of reinforced concrete (RC) beams strengthened using fabric-reinforced cementitious matrices (FRCM). Four reinforced concrete beams, including a control specimen, were fabricated, and the shear strengthening effect of the FRCM was investigated on eight shear specimens, with the strengthening type and shear reinforcement as key variables. In particular, the digital image correlation (DIC) technique was applied to closely analyze the deformation of reinforced concrete beams subjected to shear forces. The average shear strain-shear stress curve of each specimen was derived, and the contributions of shear and bending to the vertical deflection and the change in the principal strain angle with increasing shear force were analyzed. The experiment results showed that all specimens failed with diagonal cracks within the shear span. In the specimens without shear reinforcement, the shear strength increased by up to 65% according to the FRCM strengthening, while in the specimens with shear reinforcement, only the sided bond strengthened specimen showed a strength increase of 16% compared to the control specimen. Based on displacement data of the DIC, it was confirmed that FRCM strengthening can control the deformation of the RC beam. To evaluate the shear strength of the FRCM-strengthened RC beams, a shear strength model was proposed by considering the contributions of the concrete section, shear reinforcement, and FRCM. The proposed model was capable of reasonably evaluating the shear strength of RC beams strengthened with FRCM, considering the shear contribution of FRCM and bond capacity between FRCM and concrete substrate, in which the shear strength of specimens was underestimated by 28% to 35%.

Effect of using normal concrete or recycled concrete layer on behavior of repaired projectile bullet damaged reinforced concrete beams

AbstractThis study utilized experimental research to investigate the efficiency of using normal aggregate concrete (NAC) or recycled aggregate concrete (RAC) as a new concrete layer for repairing projectile bullet damage to strengthening reinforced concrete (RC) beams. This study comprised the construction and testing of eight RC beams made of RAC and NAC. They are initially subjected to projectile bullets and after that tested with flexure load to evaluate the effect of using RAC and NAC that was investigated. The findings of test results demonstrate that the repaired specimens with RAC or NAC experienced a higher load capacity than the damaged control specimens. As such, this approach could potentially use to restore RAC or NAC beams were previously damaged by projectile bullets. In addition, the findings of this research indicate that the load capacity of the damaged RC beams that were previously repaired using the NAC layer was higher than the load capacity of the damaged RC beams that were repaired using the RAC layer. The load capacity enhanced significantly of (106%–118%) and (104%–113%), respectively, when NAC and RAC are utilized in repairs. Therefore, using either NAC or RAC concrete is more economical, environmentally friendly, and efficient than demolishing.

Effect of Glass Powder as a Partial Replacement of Cement on the Flexural Behavior of Reinforced Concrete Beams Subjected to Elevated Temperature

Effect of Glass Powder as a Partial Replacement of Cement on the Flexural Behavior of Reinforced Concrete Beams Subjected to Elevated Temperature

Finite Element Analysis of Reinforced Concrete Beams Strengthened with Hybrid Fiber Reinforced Polymer Systems using ANSYS

Background: Existing reinforced concrete (RC) structures can deteriorate over time due to aging, poor construction design, natural disasters, etc. In recent years, fiber-reinforced polymer (FRP) composite materials are becoming a preferred choice for concrete construction repair due to their durability, high strength, and corrosion resistance. This study aimed to study and analyze the properties of the constituent materials to identify any weaknesses and potential improvements. Methods: The present study investigated the effectiveness of flexural strengthening of RC beams using a hybrid grouping of glass-FRP (GFRP) and carbon-FRP (CFRP) unidirectional laminates. ANSYS finite element analysis (FE) software was used to investigate the failure modes of the beams and the stress-strain parameters. The impact of adopting two different grades of reinforcing bars in RC beam modeling was also contrasted in the study. Results: Comparisons between the finite element analysis and experimental literature results were made. Based on the test findings, it could be concluded that retrofitted beams perform better than non-retrofitted beams. According to experimental results, the HY14 sheet enhanced beam had a 188.46% higher ultimate load than the unenhanced beams. Conclusion: Comparing experimental findings to the conclusions of the numerical analysis, a maximum difference of ultimate load and deflection at mid-span of 3.40% and 4.91%, respectively, were used to assess the accuracy of the results.

Flexural Behavior of Reinforced Concrete Beams with Steel-Plate Reinforced Vertical Opening

The structural response of simply supported Reinforced Concrete (RC) beams with square vertical openings is investigated in this work. Studies were conducted using seven specimens of RC beams, with the aim of comparing beams with vertical openings to those without. Meanwhile, the other beams featured carefully positioned square openings. Note that one of these beams served as the control and had no openings. Each beam was the same length (1400 mm) with a 180×120 mm cross-section. Two-point loads were applied over a span of 1200 mm throughout the testing method, with a central load placed 300 mm from the ends. The openings were positioned in the middle of the span and came in three different widths: 20, 40, and 60 mm. Openings were made using either 1.5 mm thick square steel tubing or none at all. The major goal of this study was to determine whether the steel tube could compensate for the decrease in beam strength and the impact of decreasing beam cross-section (producing opening). Correspondingly, the beam ultimate load was found to decrease by 15.75%, 24.2%, and 32.5% for opening widths of 20 mm, 40 mm, and 60 mm, respectively, as the opening width increased. On the other hand, the performance gain for beams strengthened with steel plates when steel tubes were used was 11.78%, 12.14%, and 13.28% for the respective opening widths. Doi: 10.28991/CEJ-2024-010-09-04 Full Text: PDF

Finite-Element Model Modification for Investigating the Dynamic Behavior of Fire-Exposed Reinforced Concrete Beams with Corrosion

Finite-Element Model Modification for Investigating the Dynamic Behavior of Fire-Exposed Reinforced Concrete Beams with Corrosion

Flexural Behavior of RC Continuous Beams Strengthened by Cementitious Composite Materials

Due to their great strain capacity, high tensile strength, and ability to localize cracks, cementitious composite materials are beneficial for strengthening reinforced concrete (RC) members. This paper illustrates the application of cementitious composite materials in the form of precast thin layers to strengthen a double-spanned, full-scale RC beam. Both positive and negative zones were strengthened by the precast layer embedded into the concrete cover. The precast layers have a dimension of 20 mm in thickness and 150 mm in width as that of the substrate beam and were applied by two configurations: plain and reinforced layers. A ductile smooth steel sheet with 2 mm in thickness and 100 mm in width was used inside the reinforced precast layer. The composite action of the precast layer has mutual benefits; the embedded steel sheet localizes the cracks, while the surrounding cementitious composite materials protect the steel sheet from environmental impact. The experimental results showed that the strengthening system has a significant contribution to improve the failure mode and load-carrying capacity. The use of a plain precast layer caused a 6% increase in the ultimate load and a 33% enhancement in the moment redistribution ratio compared to the control beam (CB). Applying the strengthening system with reinforced precast layer shifted the failure mode from rupture failure in the precast layer to delamination without slippage in the embedded steel sheet and matrix, leading to the full tensile capacity of the precast layer. Besides, the yielded and ultimate loads increased by 34% and 41%, respectively, and maximum deflection increased by 36%. In addition, the beam's ductility increased by 36%, and the moment redistribution ratio was enhanced by 49% compared to the CB. Doi: 10.28991/CEJ-2024-010-09-05 Full Text: PDF

Flexural performance of narrow RC beams hybrid strengthened by TRECC plate

This paper proposes a novel hybrid strengthening method for narrow reinforced concrete (RC) beams that combines fiber-reinforced polymer (FRP) textile-reinforced engineered-cementitious composites (TRECC) plates along with a self-locking anchorage system. To evaluate the effectiveness of the proposed system, a series of four-point bending tests were conducted. These tests were designed to understand the effects of different strengthening methods, number of FRP grid layers, and TRECC bond lengths. The results showed that the hybrid strengthening system could effectively prevent the end debonding failure and impede the development of the intermediate debonding in the TRECC plate. Consequently, the TRECC plate can continue to carry the force, leading to a significant increase in strengthening efficiency, quantified as the increased ratio of the peak load of the strengthened beams to that of the reference beam. Furthermore, increasing the number of FRP grid layers can also improve the strengthening efficiency. However, longer TRECC bond length in hybrid strengthened beams will reduce the strengthening efficiency since the intermediate debonding will be more susceptible to occur; the design for appropriate bond length is necessary. Finally, an analytical model to predict the flexural capacity was derived and verified against the experimental results.

Strengthening and repair of RC beams using natural sisal Fabric-Reinforced Cementitious Matrix composite

The present work reports the results of an experimental program on the mechanical characterization of Reinforced Concrete (RC) beams externally strengthened/repaired by natural sisal Fabric-Reinforced Cementitious Matrix (FRCM) composite. For such, undamaged and pre-cracked RC beams were U-wrapped with a sisal FRCM composite and then tested under bending load. The results showed significant increases in shear strength, up to 25 % for beams with stirrups and 75 % for beams without them. The strengthened/repaired beams also presented stirrups yielding delay during the tests. When compared with other synthetic FRCM strengthening systems from the literature, the enhanced mechanical results of the present work were mechanically equivalent. The cracking pattern and debonding of the sisal FRCM wrap system were measured by the Digital Image Correlation (DIC) technique. The wrap application reduced the crack propagation and debonding behavior was not detected. Finally, the experimental results were confronted with an analytical approach guided by ACI 549.4R-20 and considered sufficiently accurate.

Performance of Steel Spliced Reinforced Concrete Beams Having Construction Joints

Performance of Steel Spliced Reinforced Concrete Beams Having Construction Joints

Shear Retrofitting Effect of Self-prestressed Iron-based Shape Memory Alloy for Reinforced Concrete Beams

Shear Retrofitting Effect of Self-prestressed Iron-based Shape Memory Alloy for Reinforced Concrete Beams

Experimental Investigation of the Behavior of Loaded Fiber Reinforced Concrete Beam Exposed to Fire

Experimental Investigation of the Behavior of Loaded Fiber Reinforced Concrete Beam Exposed to Fire

Flexural behavior of reinforced concrete beams externally strengthened with ECC and FRP grid reinforcement

To prevent premature delamination of FRP sheets in strengthened concrete structures, this study explores a novel method of laying a composite layer of fiber reinforced polymer (FRP) grid reinforced with engineering cementitious composite (ECC), designated as FGRE, and applied at the soffit of reinforced concrete (RC) beams to improve its flexural performance. Experimental studies were conducted on RC beams with different strengthening configurations to validate the effectiveness of the proposed strengthening method. In addition, analysis on the working mechanism and a parametric analysis were performed for the composite strengthened beam using nonlinear finite element modeling. The experimental results showed that FGRE composite layers can significantly improve the bearing capacity of RC beams. Compared with the control RC beam, the FGRE composite strengthening technique significantly increased the cracking load, yield load, and ultimate load of the beam specimens up to 28, 11, and 12 %, respectively. The ECC grout layer maintained a good bonding performance with the concrete substrate until beam failure. The flexural capacity of RC beams with the proposed FGRE strengthening systems is determined by the thickness of the ECC layer. In addition, the effect of strengthening on the flexural capacity was more significant when the yield and tensile strength of the steel reinforcement were lower. Moreover, the prediction deviation from the experimental data of the FE models and analytical models for the ultimate load-bearing capacity were less than 2 and 7 %, respectively. It can be concluded that the proposed FGRE system is a viable solution to enhance the flexural capacity of RC beams.

Flexural behavior of corroded RC beams repaired with high performance cementitious mortar under cyclic loading

AbstractThe understanding of the cyclic performance of reinforced concrete (RC) elements is of vital importance in relation to the extent of the service life of buildings and infrastructures. Steel rebar corrosion plays a major role in this regard because it significantly affects the overall structural integrity, especially under cyclic loads, leading to reduced stiffness and load‐bearing capacity of structural elements. Cyclic condition has the potential to accelerate the corrosion‐induced cracking and spalling, the effectiveness of the bond strength between rebar and concrete, and also the ductility and energy dissipation characteristics of the structure. The primary objective of this study is to investigate the effectiveness of a high‐performance thixotropic repairing cementitious mortar in improving the fatigue behavior of RC elements through a multiscale experimental approach. First, at the material scale of concrete specimens, two different concrete classes together with the repairing one‐component, pre‐blended, thixotropic cementitious mortar, were tested under incremental cyclic condition. Based on the results obtained from material scale, four reinforced concrete beams were exposed to different levels of accelerated corrosion by means of the impressed current technique and, subsequently, repaired by bonding a layer of the thixotropic high‐performance mortar onto the tension side. Finally, beams were tested under incremental cyclic four‐point bending test to investigate the fatigue behavior in terms of crack onset, propagation and energy dissipation. The resulting cyclic properties and cracking behavior of the structural elements were related to the level of corrosion achieved through the accelerated test and the effectiveness of the structural repair mortar was proven. In terms of code compliance, the repairing mortar was able to fulfill the requirements of frequent and quasi‐permanent combination of loads, remaining below all the threshold values provided by the Italian NTC2018 and Eurocode.

Seismic performance of the ST-RC columns to RC beams exterior joint with assembled connection details

An innovative composite column type, the steel tube-reinforced concrete column (ST-RC), consists of a core of concrete-filled steel tube (CFST) and reinforced concrete (RC) encasement. This study aims to validate the reliability of two convenient and rapid assembly methods between RC beams and ST-RC columns. Four full-scale beam-column joint specimens were tested, comprising two prefabricated assembly joints of ST-RC column-RC beam frames, one integrally cast joint of ST-RC column-RC beam frames, and one traditional integrally cast joint of RC column-RC beam frames for comparison. The experiments were conducted based on the principles of a self-balanced system, and quasi-static tests under constant axial compression on the ST-RC columns were performed. Hysteresis curves, skeleton curves, failure modes, strength degradation, energy dissipation capacity, stiffness degradation, deformation capacity and the influence of connection method and joint form on mechanical performance were analyzed and obtained based on the test results. The results indicate that, compared to integral casting, the assembly surrounding method with steel sleeves reduces specimen energy dissipation by 19.8 % and damping ratio by 21 % at 4 % drift, with minimal impact on other mechanical properties. In contrast, reinforcement surrounded and connected by steel plates reduces initial stiffness and peak load-carrying capacity by 1.0 %, along with decreasing negative ductility. It also lowers total energy dissipation by 37.4 % and damping ratio by 45.4 % due to compressive effects from bottom steel plate connections. Despite these effects, its impact on negative ductility and load-carrying capacity remains minimal. Additionally, experimental observations and rebar strain data indicate higher stress on rebars at the base of steel plate connection beams, suggesting a need to strengthen transverse rebars at the beam’s base. The study confirms the feasibility of two convenient and rapid assembly methods for the joints of ST-RC column. Both methods meet current Chinese standards for MCE, with failure modes characterized by “strong columns and weak beams” in both cases.

Enhanced impact resistance of RC beams using various types of high-performance fiber-reinforced cementitious composites

This study investigates the impact resistance of reinforced concrete (RC) beams using various types of high-performance fiber-reinforced cementitious composites (HPFRCCs). A total of ten large-sized RC beams were fabricated and tested under static and impact loading conditions. Four different types of HPFRCCs with 2% by volume of steel, polyvinyl alcohol (PVA), and polyethylene (PE) fibers were considered. Ultra-high-performance fiber-reinforced concrete (UHPFRC) based on steel fibers demonstrated superior compressive and tensile strengths, while high-performance strain-hardening cementitious composite (HP-SHCC) based on PE fibers exhibited the highest strain and energy absorption capacities. The steel-bar reinforced (R-) UHPFRC and HP-SHCC beams showed superior flexural load capacity compared to reinforced normal strength concrete (R-NSC) beams. The highest ductility of 8.02 was found in the R-HP-SHCC beam, almost 5 times higher than that of the R-NSC beam. By drop hammer impact with a kinetic energy of 30 kJ, the R-UHPFRC beam completely failed due to its higher reaction load and lower structural ductility, while other RC beams made of NSC and HPFRCCs withstood the identical impact load. The R-HP-SHCC beam exhibited the best impact resistance, with a 29.1% lower maximum deflection compared to the R-NSC beam, and the largest residual load capacity after the impact damages. The R-HP-SHCC beam, despite being damaged, showed no reduction in flexural stiffness, yet it demonstrated an impressive 5.4% increase in load capacity compared to the undamaged beam.

Flexural capacity design model of reinforced concrete beams strengthened with hybrid bonded CFRP

In order to improve the calculation methodology for the flexural capacity of RC (Reinforced Concrete) beams strengthened with HB-CFRP (Hybrid Bonded-Carbon Fiber Reinforced Polymer), three-point bending tests were conducted in this study. The experimental setup involved 9 HB-CFRP strengthened T-shaped beams and 1 unstrengthened beam for comparison. The effects of anchor spacing, anchor pressure, CFRP thickness, and anchor distribution pattern on the flexural performance of strengthened beams were investigated. Additionally, the development of the full range load-deflection curves of the HB-CFRP strengthened specimens was analyzed. Two bond strength models (the Wu model and Liu model) were modified. Six parameters were considered in the modified model, namely, the CFRP elastic modulus, CFRP thickness, number of mechanical fasteners in the shear span, CFRP-concrete width ratio, concrete cylinder compressive strength and normal pressure applied to the mechanical fasteners. The accuracy of the modified models was compared on the basis of three specifications. Results indicated a notable enhancement in the flexural capacity of the strengthened beams, ranging from 61.1 % to 158.1 % compared to the unstrengthened beam. Taking the ACI specification as an example, the mean value and coefficient of variation (COV) of the flexural capacity obtained by directly using the Wu model were 1.187 and 0.169, respectively; the results obtained by using the modified Wu model based on the measured FRP strain were 1.038 and 0.125, respectively; and the results obtained by using the modified Wu model based on the ACI reversed-calculated strain were 1.012 and 0.106, respectively. After the strengthened beam reached the peak load, the load then decreased abruptly to the vicinity of the moment mid-span deflection curve of the reference beam. As the loading continued, the resistance improved by 27.4 %∼79.3 % due to the increase in interface friction in the mechanical fasteners and concrete.

Understanding and phenomenological modeling of the pinching effect of the load–deflection curve of reinforced concrete beams subjected to bending

The reliable prediction of the seismic response of reinforced concrete (RC) structures hinges on accurate modeling of the cyclic behavior of their constituent elements. The load–deflection curve in RC beams exhibits a pinched hysteresis pattern corresponding to energy dissipations. This pinching effect, often observed under seismic loading conditions, reflects a reduction in stiffness and energy dissipation capacity at certain loading stages. Despite its significance, the detailed mechanisms underlying this phenomenon remain underexplored in existing literature. This paper aims to address this gap by presenting simplified models that directly represents the pinching effect at the crack scale. The model is grounded in a comprehensive analysis of shear stress interactions and crack closure dynamics, hypothesized as primary contributors to the pinching phenomenon. Our approach involves a meticulous examination of the hysteresis loops’ area and shape, facilitating the estimation of an equivalent viscous damping ratio to represent energy dissipation in seismic simulations, irrespective of changes in the structure’s damage or ductility levels. The paper unfolds in three key sections: The first section underscores the significance of a nuanced understanding of the pinching effect in seismic analysis. The second section presents an extensive literature review, consolidating crucial insights into the nature of the pinching phenomenon. The third section details the development and application of the proposed mesoscopic model, highlighting the impact of various geometrical and material parameters on the pinching effect.