Regional Strain Research Articles

Research on the Dynamic Softening Mechanism of Dual‐Phase Structure During Warm Forming of Fe–8.5Mn–1.5Al Medium‐Manganese Steel

In this article, Fe–8.5Mn–1.5Al medium‐manganese steel is taken as the research object, and Gleeble 3500 thermal simulation testing machine is used to conduct isothermal compression at different deformation temperatures, strain rates, and strains in its austenite ferrite two‐phase zone. A constitutive model and a dynamic recrystallization volume fraction model for materials are established, and finite‐element method is used to simulate the temperature, equivalent strain, and dynamic recrystallization volume fraction distribution in different regions of the workpiece under different deformation conditions. By comparing and analyzing the microstructure, finite‐element simulation results, and hot working diagrams obtained from the experiment, the microscopic mechanism of dynamic softening of the material when ferrite and austenite coexist is explained; the transformation of the dynamic softening mechanism of the two phases with the hot deformation process is also explained. Early deformation mainly occurs in softer ferrite, which preferentially undergoes continuous dynamic recrystallization. Austenite has a lower stacking fault energy, and discontinuous dynamic recrystallization (DDRX) occurs when the dislocation density reaches a certain critical value. At the same time, when the strain reaches a certain level, the dynamic softening behavior of ferrite will also transform into DDRX. The optimal deformation conditions for Fe–8.5Mn–1.5Al medium‐manganese steel during warm processing in the two‐phase zone are a temperature of 720 °C, a strain rate of 0.01 s−1, and a large deformation zone.

Damage evolution and ductile fracture of commercially-pure titanium sheets subjected to simple tension and cyclic bending under tension

This paper describes a study into the evolution of damage in commercial-purity titanium (CP–Ti) sheets subjected to cyclic bending under tension (CBT) and uniaxial tension (simple tension, ST). Sections were taken from sheets that were strained to various levels under both methods and were imaged using X-ray computed tomography (XCT) to reveal insights into the size, density, and distribution of microvoids in the sheets. Digital image correlation (DIC) was also used to observe the surface strain of CBT and ST sheets during testing. These results showed that elongation to failure (ETF) for CBT deformation is about 2.5× higher than for ST, local longitudinal strains in the bulk of the CBT sample are around 1.3× higher than the peak strain in the ST necked region, and 1.7× higher in the localized region of CBT failure. It was found that the volume-density of voids in both sheets followed a similar exponential increase with strain, reaching nearly 45× higher in the CBT than the ST sheets before the onset of failure, mainly due to the higher strain levels achieved. A higher volume density of voids developed in the center of sheets at high levels of strain, for both processes, with the density in the sheet center becoming approximately double that found near the edges. Scanning electron microscopy (SEM) was used to examine the fracture surface of CBT and ST sheets after failure. The observations are presented and discussed highlighting the CBT process as effective to delay ductile fracture of the CP-Ti sheets.

Frequency of and sex differences in cancer treatment-related cardiac dysfunction in trastuzumab-treated patients with salivary gland cancer: a retrospective cohort study

BackgroundTrastuzumab treatment for salivary gland, gastric, and breast cancer commonly causes cancer treatment-related cardiac dysfunction (CTRCD). CTRCD incidence by sex has not been well studied.MethodsThis retrospective cohort study investigated frequency of and sex differences in CTRCD in patients with salivary gland cancer treated with trastuzumab at our hospital from April 2017 to March 2022. All patients underwent echocardiography at baseline and after the first, third, and sixth trastuzumab courses. We measured changes in global and regional longitudinal strain (LS) after trastuzumab administration. CTRCD was defined by left ventricular ejection fraction (LVEF) or global LS (GLS). The results were compared by sex.ResultsWe recorded clinical data of 49 patients (median age [IQR], 65 [55–71] years; males [75.5%]). The median follow-up period after the sixth trastuzumab course was 120 (111–128) days. One female patient and no male patient had CTRCD defined by LVEF, and two female patients (16.7%) and seven male patients (18.9%) had CTRCD, defined by GLS. The Kaplan–Meier curves showed no significant difference in CTRCD frequency, defined by GLS (log-rank, p = 0.88), between female and male patients. In the univariate analysis, sex was not associated with CTRCD, defined by GLS. A significant difference in apical LS was observed between baseline and the third follow-up results of male patients.ConclusionsIn this study, CTRCD incidence was not significantly different between male and female patients with salivary gland cancer treated with trastuzumab. Although most previous studies have looked at female patients with breast cancer, a male patient may be found to be at similar risk of myocardial damage.

Echocardiographic assessment of left ventricular mechanics in individuals with mitral valve prolapse: a systematic review and meta-analysis.

During the last decade, a number of echocardiographic studies have employed speckle tracking echocardiography (STE) for assessing myocardial deformation properties in individuals with mitral valve prolapse (MVP), reporting not univocal results. Accordingly, we performed a systematic review and meta-analysis to summarize the main findings of these studies and to examine the overall influence of MVP on left ventricular (LV) global longitudinal strain (GLS). All echocardiographic studies assessing conventional echoDoppler parameters and myocardial strain indices in MVP individuals vs. controls without MVP, selected from PubMed and EMBASE databases, were included. The risk of bias was assessed by using the National Institutes of Health (NIH) Quality Assessment of Case-Control Studies. Continuous data (LV-GLS) were pooled as a standardized mean difference (SMD) comparing MVP group with healthy controls. The overall SMD of LV-GLS was calculated using the random-effect model. The full-texts of 15 studies with 1088 individuals with MVP and 591 healthy controls were analyzed. Average LV-GLS magnitude was significantly, even though modestly, reduced in MVP individuals in comparison to controls (19.4 ± 3.4% vs. 21.1 ± 2.8%, P < 0.001). The overall effect of MVP on LV-GLS was small-to-medium (SMD - 0.54, 95%CI -0.76,-0.32, P < 0.001). Substantial heterogeneity was detected for the included studies, with an overall I2 statistic value of 75.9% (P < 0.001). Egger's test for a regression intercept gave a P-value of 0.58, indicating no publication bias. On meta-regression analysis, none of the moderators (the age, the percentage of females among MVP individuals, body mass index, heart rate and systolic blood pressure of MVP individuals, the degree of mitral regurgitation, the type of ultrasound machine employed for strain echocardiographic imaging and finally the beta blocker treatment) was significantly associated with effect modification (all P < 0.05). Regional strain analysis, performed by two-third of the studies, highlighted a more enhanced reduction in myocardial strain parameters at level of the LV basal infero-lateral segments in all directions (longitudinal, circumferential and radial), with apical sparing. The longitudinal strain impairment detected in MVP individuals is more regional than global, with peculiar involvement of the LV basal infero-lateral segments and relative apical sparing pattern.

Personalized evaluation of the passive myocardium in ischemic cardiomyopathy via computational modeling using Bayesian optimization.

Biomechanics-based patient-specific modeling is a promising approach that has proved invaluable for its clinical potential to assess the adversities caused by ischemic heart disease (IHD). In the present study, we propose a framework to find the passive material properties of the myocardium and the unloaded shape of cardiac ventricles simultaneously in patients diagnosed with ischemic cardiomyopathy (ICM). This was achieved by minimizing the difference between the simulated andthe target end-diastolic pressure-volume relationships (EDPVRs) using black-box Bayesian optimization, based on the finite element analysis (FEA). End-diastolic (ED) biventricular geometry and the location of the ischemia were determined from cardiac magnetic resonance (CMR) imaging. We employed our pipeline to model the cardiac ventricles of three patients aged between 57 and 66years, with and without the inclusion of valves. An excellent agreement between the simulated and thetarget EDPVRs has been reached. Our results revealed that the incorporation of valvular springs typically leads to lower hyperelastic parameters for both healthy and ischemic myocardium, as well as a higher fiber Green strain in the viable regions compared to models without valvular stiffness. Furthermore, the addition of valve-related effects did not result in significant changes in myofiber stress after optimization. We concluded that more accurate results could be obtained when cardiac valves were considered in modeling ventricles. The present novel and practical methodology paves the way for developing digital twins of ischemic cardiac ventricles, providing a non-invasive assessment for designing optimal personalized therapies in precision medicine.

Diagnostic accuracy of Dengue NS1 lateral flow immunoassay in comparison to reverse transcriptase polymerase chain reaction and enzyme linked Immunosorbent Assay

The most widely used invitro diagnostic qualitative screening method for dengue virus infection is the lateral flow immunoassay technique. Testing of dengue non-structural antigen NS1 offers specificity in determining the active infection while testing of IgM and IgG helps in differentiating the primary and secondary dengue infections. The ELISA functions as the golden standard for dengue testing and PCR credits for the most accurate determination tool at the genetic level. The RT-PCR endorsed NS1 gene and in ELISA or LFIA NS1 antigen is used as the marker owing to the specificity and lesser chances of mutation effects. This study evaluated the performance of AG-Q Dengue NS1 LFIA kit in comparison with RT-PCR quantification cycle (Cq) Values and ELISA NS1 quantitation. The study also focused on differentiating the samples among dengue serotypes using the RealStar Dengue Type RT-PCR Kit 1.0. Dengue serotype 2 is the prominent viral strain in Kerala region succeeded by serotype 3 and 1 with a prevalence rate of 64 %, 20 % and 6 % respectively. Dengue serotype 4 was not reported during this study period. 10 % co-infection with DENV 1 & DENV 2 was also reported. The AG-Q Dengue NS1 kit stood as efficient in screening by providing positive results with samples having RT-PCR Cq values up to 43 and ELISA NS1 quantification minimum of 14 Panbio units.

Molecular epizootiology of porcine reproductive and respiratory syndrome virus in the Xinjiang Uygur Autonomous Region of China.

Rapid evolution of porcine reproductive and respiratory syndrome virus (PRRSV) is the bottleneck for effective prevention and control of PRRS. Thus, understanding the prevalence and genetic background of PRRSV strains in swine-producing regions is important for disease prevention and control. However, there is only limited information about the epizootiological situation of PRRS in the Xinjiang Uygur Autonomous Region, China. In this study, blood or lung tissue samples were collected from 1,411 PRRS-suspected weaned pigs from 9 pig farms in Changji, Shihezi, and Wujiaqu cities between 2020 and 2022. The samples were first tested by RT-quantitative PCR, yielding a PRRSV-2 positive rate of 53.6%. Subsequently, 36 PRRSV strains were isolated through initial adaptation in bone marrow-derived macrophages followed by propagation in grivet monkey Marc-145 cells. Furthermore, 28 PRRSV-positive samples and 20 cell-adapted viruses were selected for high-throughput sequencing (HTS) to obtain the entire PRRSV genome sequences. Phylogenetic analysis based on the nucleotide sequences of the ORF5 gene of the PRRSV strains identified in this study grouped into sub-lineages 1.8 and 8.7 the former being the dominant strain currently circulating in Xinjiang. However, the NSP2 proteins of the Xinjiang PRRSV strains shared the same deletion patterns as sub-lineage 1.8 prototype strain NADC30 with the exception of 4 strains carrying 2-3 additional amino acid deletions. Further analysis confirmed that recombination events had occurred in 27 of 37 PRRSVs obtained here with the parental strains belonging to sub-lineages 1.8 and 8.7, lineages 3 and 5, with the recombination events having occurred most frequently in the 5' and 3' termini of ORF1a and 5' terminus of ORF1b.

Subclinical association of aortic stiffness with cardiac structure and function in African-Americans: The Jackson Heart Study.

Cardiovascular disease (CVD) morbidity and mortality are high among black adults. We aimed to study the granular subclinical relations of aortic stiffness and left ventricular (LV) function and remodeling in blacks, in whom limited data are available. In the Jackson Heart Study, 1050 U.S. community-dwelling black adults without CVD underwent 1.5T cardiovascular magnetic resonance. We assessed regional and global aortic stiffness and LV structure and function, including LV mass indexed to body surface area (LVMI), end-diastolic volume (LVEDV), ejection fraction (EF), and global and regional circumferential strain (Ecc). Phase contrast images of the cross-sectional aorta at the pulmonary artery bifurcation and abdominal aorta bifurcation were acquired to measure pulse wave velocity of the aortic arch (AA-PWV) and thoracic aorta (T-PWV). Results of multivariable-adjusted analyses are presented as SD unit change in LV variables per SD change in PWV variables. Participants were 62% women with mean age of 59 ± 10years. Higher AA-PWV and T-PWV were associated with greater LVMI: for T-PWV, β = 0.10, 95% CI = 0.03-0.16, p = 0.002. Higher AA-PWV and T-PWV were associated with worse (more positive) Ecc at the LV base (for AA-PWV, β = 0.13, 95% CI = 0.05-0.20, p = 0.0007), but not mid-LV or apex. AA-PWV and T-PWV were not associated with LV mass/LVEDV or EF. In this cross-sectional study of blacks without CVD in the U.S., aortic stiffness is associated with subclinical adverse LV function in basal segments. Future studies may elucidate the temporal relationships of aortic stiffness on the pattern and progression of LV remodeling, dysfunction, and associated prognosis in blacks.

The effects of different anode manufacturing methods on deep levels in 4H-SiC p+n diodes

The manufacture of bipolar junctions is necessary in many 4H-SiC electronic devices, e.g., junction termination extensions and p+in diodes for voltage class &amp;gt;10 kV. However, the presence of electrically active levels in the drift layer that act as minority charge carrier lifetime killers, like the carbon vacancy (VC), undermines device performance. In the present study, we compared p+n diodes whose anodes have been manufactured by three different methods: by epitaxial growth, ion implantation, or plasma immersion ion implantation (PIII). The identification of the electrically active defects in the drift layers of these devices revealed that a substantial concentration of VC is present in the diodes with epitaxial grown or ion implanted anode. On the other hand, no presence of VC could be detected when the anode is formed by PIII and this is attributed to the effects of strain in the anode region. Our investigation shows that PIII can be a useful technique for the manufacture of bipolar devices with a reduced concentration of lifetime killer defects.

Association between cardiac magnetic resonance ventricular strain and left ventricular thrombus in patients with ST-segment elevation myocardial infarction.

Myocardial strain can analyze early myocardial dysfunction after myocardial infarction (MI). However, the correlation between left ventricular (LV) strain (including regional and global strain) obtained by cardiac magnetic resonance (CMR) imaging and left ventricular thrombus (LVT) after ST-segment elevation myocardial infarction (STEMI) is unclear. The retrospective clinical observation study included patients with LVT (n = 20) and non-LVT (n = 195) who underwent CMR within two weeks after STEMI. CMR images were analyzed using CVI 42 (Circle Cardiovascular Imaging, Canada) to obtain LV strain values. Logistic regression analysis identified risk factors for LVT among baseline characteristics, CMR ventricular strain, and left ventricular ejection fraction (LVEF). Considering potential correlations between strains, the ability of LV strain to identify LVT was evaluated using 9 distinct models. Receiver operating characteristic curves were generated with GraphPad Prism, and the area under the curve (AUC) of LVEF, apical longitudinal strain (LS), and circumferential strain (CS) was calculated to determine their capacity to distinguish LVT. Among 215 patients, 9.3% developed LVT, with a 14.5% incidence in those with anterior MI. Univariate regression indicated associations of LAD infarct-related artery, lower NT-proBNP, lower LVEF, and reduced global, midventricular, and apical strain with LVT. Further multivariable regression analysis showed that apical LS, LVEF and NT-proBNP were still independently related to LVT (Apical LS: OR = 1.14, 95%CI (1.01, 1.30), P = 0.042; LVEF: OR = 0.91, 95%CI (0.85, 0.97), P = 0.005; NT-proBNP: OR = 2.35, 95%CI (1.04, 5.31) ). Reduced apical LS on CMR is independently associated with LVT after STEMI.

The Value of 2D Global Longitudinal Strain in Predicting the Severity of Coronary Artery Disease in Patients with NSTEMI and Unstable Angina and Regional Strain Value for Predicting the Culprit Artery

Background: Our study aimed to evaluate the predictive ability of resting strain to determine the severity of CAD in the absence of impaired LVEF in patients with NSTEMI and unstable angina. Additionally, the study sought to predict culprit and infracted related artery (IRA) using regional strain (SLR). Methods: The study was conducted between January 2023 and May 2023 at the cardiology department of Ibn Rochd Hospital, Morocco. We conducted a comparative analysis involving 30 patients, comprising 23 individuals with NSTEMI and 7 with unstable angina. In all cases, we assessed both GLS and RLS before proceeding to coronary angiography. Subsequently, we categorized the patients into two groups: one consisted of 18 individuals with severe coronary lesions, including left main trunk (LM) and three vessels lesions, while the other group, comprising 12 patients, served as the control group and had non-severe coronary lesions Results: At resting GLS threshold below -16,3 %, despite its subnormal nature, should raise suspicion and suggest severe coronary artery disease. RLS in the "Single-vessel" group was significantly lower in the culprit artery territories, suggesting that RLS may be a better marker for identifying the culprit artery. Both GLS and the visual analysis of segmental kinetics by WMSI (Wall Motion Score Index) at rest, were statistically significant for detecting severe coronary lesions. Conclusion: GLR and SLR are sensitive markers for early detection of myocardial ischemia and predicting its severity. A resting GLR threshold of less than -16.13% could indicate severe CAD with severe tri-truncular or LMT damage, especially when combined with abnormal WMSI scores. These 2D strain parameter changes precede subjective abnormalities in segmental kinetics, which are often considered normal at rest.

Longitudinal strain correlates with 6-minute walk distance whereas ejection fraction and diastolic parameters do not

BackgroundImpaired functional capacity is a common symptom in patients with heart failure. Standard measures of left ventricular (LV) function, such as ejection fraction (EF) and LV diastolic parameters, do not correlate with measures of functional capacity. The aim of this study is to determine if measures of global and regional LV strain better correlate with 6-minute walk distance than does EF or measures of LV diastolic function.Methods120 patients referred to a cardiology clinic for evaluation of known or suspected heart failure were approached for enrollment. Of those 120 patients, 58 had an echocardiogram within 3 months of enrollment with images adequate for regional and global strain assessment, had no contra-indication to exercise testing, and had no previously documented non-cardiac explanation for dyspnea on exertion. In those 58 patients, 6-minute walk distance was measured, LV EF was determined with Simpson’s biplane method, and global and regional longitudinal strain were measured with TomTec Image Arena 4.5.1 software.ResultsLV EF had no correlation with 6-minute walk distance (r = 0.22, p = 0.09) even when controlling for age, gender, and BMI (p = 0.07). No measures of LV diastolic function (including E velocity, Deceleration Time, e’ annular velocities, or E/e’) had a correlation with 6-minute walk distance. Multiple measures of global and regional LV longitudinal systolic function had a correlation with 6-minute walk distance. Longitudinal strain of the basal LV segments had the strongest correlation with 6-minute walk distance (r= -0.36, p = 0.005), and correlation persisted after controlling for age, gender, BMI, and systolic blood pressure (p = 0.004).ConclusionsLongitudinal strain correlates with a measure of functional capacity, but LVEF and traditional measures of LV diastolic dysfunction do not. Measures of longitudinal strain, especially in basal LV segments, will likely be an important marker of clinically relevant LV function.Graphical

The Cyclic Performance and Macro-Simplified Analytical Model of Internal Joints in RC-Assembled Frame Structures Connected by Unbonded Prestressed Strands and Mortise-Tenon Based on Numerical Studies

This paper introduces a novel type of connection that integrates unbonded prestressed strands (UPS) and mortise-tenon in an assembly frame structure (UPS-MTF). First, the damage process and failure modes of the joints under reciprocating horizontal loads were systematically analyzed using refined numerical models. The recommended values of the design parameters of the joints were derived from the parametric analysis results. Refined numerical modeling results reveal the diagonal compression strut mechanism within the core region of the joint. The diagonal compression struts model assists in establishing the theoretical calculation formula for the skeleton curve of shear stress–strain in the core region. Second, a genetic algorithm (GA) parameter was identified for the restoring force model of the core region to determine the parameters of the hysteresis rules. Finally, a macro-simplified analytical model of the joint was created based on the restoring force model of the core region, and parameter analysis was conducted to verify the applicability of this macro-simplified analytical model. The research results prove that the damaged form of the joint proposed in this paper originates from the shear and relative slip damage between the components in the core region. The axial compression ratio significantly affects the hysteretic performance of the joints, and the upper and lower limit values were identified for the axial compression ratio of the joints. The area and initial effective stress of the UPS exert a minimal effect on the hysteretic performance of the joint. Based on the method proposed in this paper for determining the restoring force model in the core region of the joints, the hysteresis curves obtained from the macro-simplified analytical model closely match the refined numerical analysis model results. This correspondence verifies the applicability of the macro-simplified analytical model.

The role of atrial pacing site in reducing filling pressures by accelerated pacing in virtual HFpEF patients

Abstract Background Patients with heart failure with preserved ejection fraction (HFpEF) and pacemakers have been shown to benefit from moderately accelerated pacing rates compared to the standard 60bpm. HFpEF patients often present with prolonged P-wave duration (PWD) and atrial fibrillation. Right atrial appendage pacing (RAAP) lengthens PWD, RA septal (RASP) has a neutral effect, while Bachmann’s bundle pacing (BBP) normalizes or shortens PWD compared to sinus rhythm. The mechanical and hemodynamic effects of atrial pacing site selection remain unknown. Aim To investigate the impact of RAAP, RASP and BBP on cardiac mechanics and hemodynamics in an established cohort of virtual HFpEF patients undergoing accelerated pacing. Method HFpEF with prolonged PWD was simulated using the validated CircAdapt computational model of the human cardiovascular system. First, left ventricular (LV) diastolic dysfunction was simulated by decreasing LV myocardial relaxation rate and compliance, such that mean left atrial (LA) pressure (mLAP) was 15mmHg. Second, PWD was prolonged by prescribing a gradual electrical activation delay from RA to LA of 140ms. We then simulated atrial pacing with three different lead positions (Fig.1, left) and gradually increased pacing rate with a constant 120-ms paced atrioventricular (AV) delay. The CircAdapt model computed regional LA strain and mLAP with RAAP, RASP, and BBP. Cardiac output (5L/min) and mean arterial pressure (92mmHg) were kept constant in all simulations. Results Simulated BBP demonstrated the most synchronous LA mechanical activation and function, characterized by uniform segmental LA strain patterns and highest LA reservoir strain (LASR) (Fig.1, middle, with colored arrows highlighting the mechanical dyssynchrony). Hemodynamically (Fig.1, right), BBP acutely decreased mLAP (-1.0mmHg) at the initial heart rate of 60bpm, while RAAP increased it (+0.3mmHg). As pacing rate accelerated, BBP reduces filling pressure (mLAP: -2.8mmHg), more than RASP (-1.8mmHg) or RAAP (-1.2mmHg) at 80bpm. At high pacing rates, RASP and RAAP adversely increase mLAP, due to the prolonged atrial contraction duration and shorter LV filling time. Conclusion Our simulations of different atrial pacing sites in virtual HFpEF patients suggest that BBP yields the most synchronous LA activation pattern and a more substantial reduction in filling pressures with accelerated atrial pacing compared to RASP. Reduction in mLAP with accelerated pacing was attenuated with RAAP. While our study concentrated on a specific paced AV interval, the favorable outcomes observed with BBP could be further improved by including different, rate-adaptive, AV protocols.Fig 1.

The effect of suboccipital muscle dysfunction on the biomechanics of the upper cervical spine: a study based on finite element analysis

ObjectiveMuscle dysfunction caused by repetitive work or strain in the neck region can interfere muscle responses. Muscle dysfunction can be an important factor in causing cervical spondylosis. However, there has been no research on how the biomechanical properties of the upper cervical spine change when the suboccipital muscle group experiences dysfunction. The objective of this study was to investigate the biomechanical evidence for cervical spondylosis by utilizing the finite element (FE) approach, thus and to provide guidance for clinicians performing acupoint therapy.MethodsBy varying the elastic modulus of the suboccipital muscle, the four FE models of C0-C3 motion segments were reconstructed under the conditions of normal muscle function and muscle dysfunction. For the two normal condition FE models, the elastic modulus for suboccipital muscles on both sides of the C0-C3 motion segments was equal and within the normal range In one muscle dysfunction FE model, the elastic modulus on both sides was equal and greater than 37 kPa, which represented muscle hypertonia; in the other, the elastic modulus of the left and right suboccipital muscles was different, indicating muscle imbalance. The biomechanical behavior of the lateral atlantoaxial joint (LAAJ), atlanto-odontoid joint (ADJ), and intervertebral disc (IVD) was analyzed by simulations, which were carried out under the six loadings of flexion, extension, left and right lateral bending, left and right axial rotation.ResultsUnder flexion, the maximum stress in LAAJ with muscle imbalance was higher than that with normal muscle and hypertonia, while the maximum stress in IVD in the hypertonic model was higher than that in the normal and imbalance models. The maximum stress in ADJ was the largest under extension among all loadings for all models. Muscle imbalance and hypertonia did not cause overstress and stress distribution abnormalities in ADJ.ConclusionMuscle dysfunction increases the stress in LAAJ and in IVD, but it does not affect ADJ.

Static and Dynamic Strain in the 1886 Charleston, South Carolina, Earthquake

ABSTRACT During the 1886 Mw 7.3 Charleston, South Carolina, earthquake, three railroads emanating from the city were exposed to severe shaking. Expansion joints in segmented railroad tracks are designed to allow railroad infrastructure to withstand a few parts in 10,000 of thermoelastic strain. We show that, in 1886, transient contractions exceeding this limiting value buckled rails, and transient extensions pulled rails apart. Calculated values for dynamic strain in the meizoseismal region are in reasonable agreement with those anticipated from the relation between strain and moment magnitude proposed by Barbour et al. (2021) and exceed estimated tectonic strain released by the earthquake by an order of magnitude. Almost all of the documented disturbances of railroad lines, including evidence for shortening of the rails, can thus be ascribed to the effects of dynamic strain changes, not static strain. Little or no damage to railroads was reported outside the estimated 10−4 dynamic strain contour. The correspondence between 10−3 and 2×10−4 contours of dynamic strain and Mercalli intensity 9 and 8, anticipated from the dependence of each quantity on peak ground velocity, suggests it may be possible to use railroad damage to quantitatively estimate shaking intensity. At one location, near Rantowles, ≈20 km west of Charleston, a photograph of buckled track taken one day after the earthquake has been cited as evidence for shallow dextral slip and has long focused a search for a causal fault in this region. Photogrammetric analysis reveals that the buckle was caused by transient contraction of &amp;lt;10 cm with no dextral offset. Our results further weaken the evidence for faulting in the swamps and forests south of the Ashley River in 1886, hitherto motivated by the photograph and limited macroseismic evidence for high-intensity shaking.

Parameter subset reduction for imaging-based digital twin generation of patients with left ventricular mechanical discoordination

BackgroundIntegration of a patient’s non-invasive imaging data in a digital twin (DT) of the heart can provide valuable insight into the myocardial disease substrates underlying left ventricular (LV) mechanical discoordination. However, when generating a DT, model parameters should be identifiable to obtain robust parameter estimations. In this study, we used the CircAdapt model of the human heart and circulation to find a subset of parameters which were identifiable from LV cavity volume and regional strain measurements of patients with different substrates of left bundle branch block (LBBB) and myocardial infarction (MI). To this end, we included seven patients with heart failure with reduced ejection fraction (HFrEF) and LBBB (study ID: 2018-0863, registration date: 2019–10–07), of which four were non-ischemic (LBBB-only) and three had previous MI (LBBB-MI), and six narrow QRS patients with MI (MI-only) (study ID: NL45241.041.13, registration date: 2013–11–12). Morris screening method (MSM) was applied first to find parameters which were important for LV volume, regional strain, and strain rate indices. Second, this parameter subset was iteratively reduced based on parameter identifiability and reproducibility. Parameter identifiability was based on the diaphony calculated from quasi-Monte Carlo simulations and reproducibility was based on the intraclass correlation coefficient (ICC\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${ICC}$$\\end{document}) obtained from repeated parameter estimation using dynamic multi-swarm particle swarm optimization. Goodness-of-fit was defined as the mean squared error (χ2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${{{\\chi}}}^{{2}}$$\\end{document}) of LV myocardial strain, strain rate, and cavity volume.ResultsA subset of 270 parameters remained after MSM which produced high-quality DTs of all patients (χ2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${{{\\chi}}}^{{2}}$$\\end{document} < 1.6), but minimum parameter reproducibility was poor (ICCmin\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${{ICC}}_{{min}}$$\\end{document} = 0.01). Iterative reduction yielded a reproducible (ICCmin\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${{ICC}}_{{min}}$$\\end{document} = 0.83) subset of 75 parameters, including cardiac output, global LV activation duration, regional mechanical activation delay, and regional LV myocardial constitutive properties. This reduced subset produced patient-resembling DTs (χ2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${{{\\chi}}}^{{2}}$$\\end{document} < 2.2), while septal-to-lateral wall workload imbalance was higher for the LBBB-only DTs than for the MI-only DTs (p < 0.05).ConclusionsBy applying sensitivity and identifiability analysis, we successfully determined a parameter subset of the CircAdapt model which can be used to generate imaging-based DTs of patients with LV mechanical discoordination. Parameters were reproducibly estimated using particle swarm optimization, and derived LV myocardial work distribution was representative for the patient’s underlying disease substrate. This DT technology enables patient-specific substrate characterization and can potentially be used to support clinical decision making.

The Impact of Drop Test Conditions on Brain Strain Location and Severity: A Novel Approach Using a Deep Learning Model

In contact sports such as rugby, players are at risk of sustaining traumatic brain injuries (TBI) due to high-intensity head impacts that generate high linear and rotational accelerations of the head. Previous studies have established a clear link between high-intensity head impacts and brain strains that result in concussions. This study presents a novel approach to investigating the effect of a range of laboratory controlled drop test parameters on regional peak and mean maximum principal strain (MPS) predictions within the brain using a trained convolutional neural network (CNN). The CNN is publicly available at https://github.com/Jilab-biomechanics/CNN-brain-strains. The results of this study corroborate previous findings that impacts to the side of the head result in significantly higher regional MPS than forehead impacts. Forehead impacts tend to result in the lowest region-averaged MPS values for impacts where the surface angle was at 0° and 45°, while side impacts tend to result in higher regional peak and mean MPS. The absence of a neck in drop tests resulted in lower regional peak and mean MPS values. The results indicated that the relationship between drop test parameters and resulting regional peak and mean MPS predictions is complex. The study’s findings offer valuable insights into how deep learning models can be used to provide more detailed insights into how drop test conditions impact regional MPS. The novel approach used in this paper to predict brain strains can be applied in the development of better methods to reduce the brain strain resulting from head accelerations such as protective sports headgear.

Diagnostic value of left ventricular layer strain and specific regional strain patterns in cardiac amyloidosis and Fabry disease.

Layer-specific left ventricular (LV) strain alterations have been suggested as a specific finding in Fabry disease (FD). Our study aimed to assess the diagnostic value of layer-specific radial strain (RS) indices compared to the established LV regional strain pattern in cardiac amyloidosis (CA) and FD, i.e. apical sparing and posterolateral strain deficiency (PLSD). We retrospectively analysed the global, subendocardial, subepicardial LV radial strain, the corresponding strain gradient, as well as the regional and global longitudinal strain. The diagnostic accuracy of the diverse LV strain analyses was comparatively assessed using receiver operating characteristic curve and multivariable regression analyses. In 40 FD and 76 CA patients, CA featured more reduced layer strain values [global RS -12.3 (-15.6 to -9.6) in CA vs. -16.7 (-20.0 to -13.6) in FD; P < 0.001; subendocardial RS -22.3 (-27.4 to -15.9) vs. -28.3 (-31.8 to -23.6), P < 0.001; subepicardial RS -6.6 (-8.6 to -4.7) in CA vs. -8.9 (-11.7 to - 6.5) in FD; P < 0.001]. Global radial and longitudinal strain held an area under the curve (AUC) of 0.75 (0.66-0.84) and AUC 0.73 (0.63-0.83). While the apical sparing and PLSD strain pattern showed the highest accuracy as single parameters [AUC 0.87 (0.79-0.95) and 0.81 (0.72-0.89), P < 0.001], the combination of subendocardial RS and the apical sparing pattern featured the highest diagnostic accuracy [AUC 0.92 (0.87-0.97)]. Combining radial strain-derived parameters to the established strain pattern apical sparing and PLSD improve the diagnostic accuracy in the echocardiographic assessment in suspected storage disease.

LEFT VENTRICULAR STRAIN IN PATIENTS WITH HYPERTENSIVE HEART DISEASE AND NORMAL EJECTION FRACTION ASSESSED BY SPECKLE TRACKING ECHOCARDIOGRAPHY

Objective: Hypertension is a major risk factor for cardiovascular diseases and is associated with increased all-cause and cardiovascular mortality. Cardiac changes such as impaired left ventricular (LV) function, left ventricular hypertrophy (LVH), and heart failure are consequences of chronic exposure to elevated blood pressure. Speckle tracking echocardiography (STE) is a sensitive method for detecting early regional and global myocardial dysfunction missed in asymptomatic patients with cardiovascular disease by conventional modalities. This study aimed to assess the ability of 2D-STE in assessing regional and global LV strain to diagnose subclinical LV dysfunction in patients with systemic hypertension and preserved ejection fraction. Design and method: This prospective observational study included 80 hypertensive patients and 30 healthy controls. In the hypertensive group, at least six months had passed from diagnosis of hypertension according to AHA guidelines. 2D echocardiographic LV images were acquired in apical 4, 2, and 3-chamber and parasternal short axis views. Left ventricular global longitudinal strain (LVGLS) and circumferential strain (LVGCS) were quantified in all segments using a Philips Affiniti 70 device. Differences between hypertensive patients and controls were analyzed using the independent t-test. A P-value less than 0.05 was considered statistically significant. Results: In comparison, LVGLS and LVGCS were significantly (P &lt; 0.001) lower among the hypertensive group (GLS: -17.43 ± 1.71, GCS: -23.76 ± 3.35) than the control group (GLS: -20.18 ± 1.11, GCS: -27.46 ± 4.33). LVGLS was significantly (P &lt; 0.001) lower in uncontrolled hypertension (-16.91 ± 1.70) vs. controlled hypertension (-17.96 ± 1.57). Similarly, LVGLS was significantly (P &lt; 0.001) lower among the cases with LVH on 2D echocardiography (16.23 ± 1.69) compared to those without LVH (17.96 ± 1.6). In the hypertensive group, LVGLS was significantly lower in males (-16.84 ± 1.42) than in females (-18.02 ± 1.78; P &lt; 0.05). Conclusions: This study demonstrates the potential benefits of using STE as a noninvasive imaging technique in assessing cardiac remodeling and providing a further risk assessment of hypertensive patients.