Regenerated Fiber Bragg Gratings Research Articles

Regeneration of fiber Bragg gratings under strain

The effect of strain on both the index modulation, Δn(mod), and average index, Δn, during grating regeneration within two types of fibers is studied. Significant tunability of the Bragg wavelength (λ(B)>48 nm) is observed during postannealing at or above the strain temperature of the glass. The main reason for the grating wavelength shift during annealing with load is the elongation of the fiber. As well, the observed Moiré interference cycling through regeneration indicates the presence of two gratings.

Production of optical notch filters with fine parameter control using regenerated fiber Bragg gratings

A new method to create a controlled notch filter for attenuation of signals based on regenerated fiber Bragg gratings is experimentally demonstrated. A fine adjustment of the notch depth is achieved by controlling the time of regeneration phenomenon in strongly saturated Bragg gratings written in standard ITU G.652 single-mode fiber. This method can used to produce tailored notch filters for several photonic applications, such as optical RF filtering, subcarrier processing or radio over fiber systems.

Packaged Optical Sensors Based on Regenerated Fiber Bragg Gratings for High Temperature Applications

We report on temperature sensors based on regenerated fiber Bragg gratings (RFBGs) for measurements up to 1100. The annealing process required to regenerate such gratings makes the optical fiber too delicate, thus making an adequate packaging necessary. Prior to the grating regeneration the optical fiber is protected with a ceramic tube which in turn is shielded with a thick metal casing. We have performed a thorough characterization of the thermo-optical response of both packaged and unpackaged RFBG sensors placing especial attention on possible residual hysteresis after several temperature cycling tests. The response and recovery times of packaged sensors were found to be, respectively, ~9 s and ~ 22 s.

Optical fiber sensors embedded in concrete for measurement of temperature in a real fire test

We present the results of a real fire test using optical fiber sensors embedded in concrete samples. The temperature curve used in this experiment is described in the Spanish/European standard UNE-EN 1363-1 temperature profile for normalized concrete resistance to real fire tests, reaching temperatures of more than 1000°C inside the fire chamber and up to 600°C inside the concrete samples. Three types of optical sensors have been embedded in concrete: 1. standard fiber Bragg gratings inscribed in photosensitive germanium-boron co-doped fiber, 2. regenerated fiber Bragg grating (RFGB) inscribed in germanium doped fiber, and 3. RFBG inscribed in germanium-boron co-doped fiber.

Regenerated gratings in air-hole microstructured fibers for high-temperature pressure sensing

We present thermally regenerated fiber Bragg gratings in air-hole microstructured fibers for high-temperature, hydrostatic pressure measurements. High-temperature stable gratings were regenerated during an 800 °C annealing process from hydrogen-loaded Type I seed gratings. The wavelength shifts and separation of grating peaks were studied as functions of external hydrostatic pressure from 15 to 2400 psi, and temperature from 24 °C to 800 °C. This Letter demonstrates a multiplexible pressure and temperature sensor technology for high-temperature environments using a single optical fiber feedthrough.

Thermal regenerated type IIa fiber Bragg gratings for ultra-high temperature operation

Thermally regenerated fiber Bragg gratings written in photosensitive fibers with nanosecond laser pulses without hydrogen loading have been shown to become temperature stable up to 600 °C. In this paper, we give an experimental analysis of the refractive index development for fabricating the gratings and for the thermal regeneration process. Furthermore, we identify a thermal induced type IIa (type I n) behavior of the refractive index to be responsible for the regeneration. The variation of refractive index modulation and the average index in the grating region is discussed. With additional annealing it is possible to improve the temperature stability beyond 1000 °C.

Arrays of Regenerated Fiber Bragg Gratings in Non-Hydrogen-Loaded Photosensitive Fibers for High-Temperature Sensor Networks

We report about the possibility of using regenerated fiber Bragg gratings generated in photosensitive fibers without applying hydrogen loading for high temperature sensor networks. We use a thermally induced regenerative process which leads to a secondary increase in grating reflectivity. This refractive index modification has shown to become more stable after the regeneration up to temperatures of 600 °C. With the use of an interferometric writing technique, it is possible also to generate arrays of regenerated fiber Bragg gratings for sensor networks.

Thermal regeneration of fiber Bragg gratings in photosensitive fibers

We report about a thermal regeneration of fiber Bragg gratings written in photosensitive fibers with nanosecond laser pulses. We observe a regenerative process in a highly photosensitive fiber without hydrogen loading which indicates a secondary grating growth in an optical fiber by thermal activation. This process is more temperature stable than the commonly known gratings produced by color center modifications. The writing conditions of such new type of gratings are investigated and the temperature behavior of these regenerated fiber Bragg gratings is analyzed. The application possibilities are in the field of high temperature sensor systems by making use of the combination of good spectral shape of a Type I grating with a Type II like temperature stability.

Abnormal spectral evolution of fiber Bragg gratings in hydrogenated fibers

We report the observation of abnormal spectral evolution in regenerated fiber Bragg gratings in hydrogenated B-Ge-codoped and standard telecom fiber with UV overexposure. The behavior of this new type of regenerated grating, which we have designated type IA, contrasts with that of the previously reported type IIA grating in nonhydrogenated fiber by exhibiting a large redshift in Bragg wavelength with increasing exposure of as much as 18 nm from a strong (16-dB) regenerated grating in B-Ge fiber.