Tension Reduction Research Articles

Formulation and Characterization of Soybean Oil-in-Water Emulsions Stabilized Using Gelatinized Starch Dispersions from Plant Sources.

Consumers are concerned about employing green processing technologies and natural ingredients in different manufacturing sectors to achieve a "clean label" standard for products and minimize the hazardous impact of chemical ingredients on human health and the environment. In this study, we investigated the effects of gelatinized starch dispersions (GSDs) prepared from six plant sources (indica and japonica rice, wheat, corn, potatoes, and sweet potatoes) on the formulation and stability of oil-in-water (O/W) emulsions. The effect of gelatinization temperature and time conditions of 85-90 °C for 20 min on the interfacial tension of the two phases was observed. Emulsification was performed using a primary homogenization condition of 10,000 rpm for 5 min, followed by high-pressure homogenization at 100 MPa for five cycles. The effects of higher oil weight fractions (15-25% w/w) and storage stability at different temperatures for four weeks were also evaluated. The interfacial tension of all starch GSDs with soybean oil decreased compared with the interfacial tension between soybean oil and water as a control. The largest interfacial tension reduction was observed for the GSD from indica rice. Microstructural analysis indicated that the GSDs stabilized the O/W emulsion by coating oil droplets. Emulsions formulated using a GSD from indica rice were stable during four weeks of storage with a volume mean diameter (d4,3) of ~1 µm, minimal viscosity change, and a negative ζ-potential.

Influence of Varying Oil-Water Contents on the Formation of Crude Oil Emulsion and Its Demulsification by a Lab-Grown Nonionic Demulsifier.

This study describes how varying oil/water contents affect emulsion formation and the impact they have on emulsion droplet size, viscosity, and interfacial behavior. Crude oil (continuous phase) volume fractions of 40, 50, 60, and 70 vol % were probed in the various W/O emulsions formed. Experimental results from optical morphology revealed the emulsion droplets kept reducing as the crude oil fraction kept increasing, while the droplets were nearly unnoticeable in the emulsions derived from 60 and 70% crude oil. The viscosity-shear rate of emulsions produced from 40, 50, and 60 vol % crude oil exhibited a non-Newtonian behavior owing to the substantial volume of water content in their emulsions, whereas the viscosity-shear rate of the emulsion with 70 vol % crude oil exhibited a Newtonian behavior similar to the pure crude oil, suggesting a thorough blending of oil-water at this crude oil fraction. Besides, the viscosity-temperature measurements revealed that the viscosity of these emulsions diminished as the temperature increased and the viscosity reduction became more noticeable in an emulsion comprising 70 vol % crude oil. In the interfacial assessment, the increased crude oil content in the produced emulsion led to a sharp reduction in the interfacial tension (IFT). The IFT values after 500 s contacts between the emulsion and water (surrounding phase) were 11.86, 10.02, 8.08, and 6.99 mN/m for 40, 50, 60, and 70 vol % crude oil, respectively. Demulsification experiments showed that water removal becomes more challenging with a large volume of crude oil and a small water content. Demulsification performances of the lab-grown nonionic demulsifier (NID) after 10 h of demulsification activity at room temperature (25 °C) were 98, 90, 17.5, and 10% for the emulsions formed from 40, 50, 60, and 70 vol % crude oil, respectively, indicating that the demulsification degree decreases with an increasing crude oil content. Viscosity-time determination was applied to affirm the activity of NID on the emulsion formulated with a 50% crude oil fraction. The injection of NID in this emulsion triggered a sharp viscosity reduction, indicating the adsorption of NID at the oil-water interface and disruption of emulsifiers, enabling emulsion stability.

Characterization of NEB pathogenic variants in patients reveals novel nemaline myopathy disease mechanisms and omecamtiv mecarbil force effects.

Nebulin, a critical protein of the skeletal muscle thin filament, plays important roles in physiological processes such as regulating thin filament length (TFL), cross-bridge cycling, and myofibril alignment. Pathogenic variants in the nebulin gene (NEB) cause NEB-based nemaline myopathy (NEM2), a genetically heterogeneous disorder characterized by hypotonia and muscle weakness, currently lacking curative therapies. In this study, we examined a cohort of ten NEM2 patients, each with unique pathogenic variants, aiming to understand their impact on mRNA, protein, and functional levels. Results show that pathogenic truncation variants affect NEB mRNA stability and lead to nonsense-mediated decay of the mutated transcript. Moreover, a high incidence of cryptic splice site activation was found in patients with pathogenic splicing variants that are expected to disrupt the actin-binding sites of nebulin. Determination of protein levels revealed patients with either relatively normal or markedly reduced nebulin. We observed a positive relation between the reduction in nebulin and a reduction in TFL, or reduction in tension (both maximal and submaximal tension). Interestingly, our study revealed a pathogenic duplication variant in nebulin that resulted in a four-copy gain in the triplicate region of NEB and a much larger nebulin protein and longer TFL. Additionally, we investigated the effect of Omecamtiv mecarbil (OM), a small-molecule activator of cardiac myosin, on force production of type 1 muscle fibers of NEM2 patients. OM treatment substantially increased submaximal tension across all NEM2 patients ranging from 87 to 318%, with the largest effects in patients with the lowest level of nebulin. In summary, this study indicates that post-transcriptional or post-translational mechanisms regulate nebulin expression. Moreover, we propose that the pathomechanism of NEM2 involves not only shortened but also elongated thin filaments, along with the disruption of actin-binding sites resulting from pathogenic splicing variants. Significantly, our findings highlight the potential of OM treatment to improve skeletal muscle function in NEM2 patients, especially those with large reductions in nebulin levels.

Can the late dark energy parameterization reconcile the Hubble tension?* *Ming-Jian Zhang is Supported by the Natural Science Foundation of Shandong Province, China (ZR2021MA075), and the Talent Research Project of Qilu University of Technology (2023RCKY029). Li Chen is Supported by the Natural Science Foundation of Shandong Province, China (ZR2019MA033)

In this study, we constructed ten dark energy models to test whether they can reconcile the Hubble tension and how much it is affected by parameterization. To establish a fair test, the models are diverse, encompassing fractional, logarithmic, exponential, and inverse exponential forms as well as several non-parameterized models. The dataset we used includes the NPIPE pipeline of cosmic microwave background (CMB) power-spectrum data from Planck2020, Pantheon+ samples from Supernovae Type Ia, and baryon acoustic oscillations. The MCMC calculations imply dark energy transferring from to for the four parameterized dark energy models. However, these models cannot adequately reconcile the Hubble tension. Notably, we found that phantom-like dark energy with can achieve the greatest reduction in the Hubble tension to . However, AIC analysis indicates that this alleviation is at the cost of high AIC. We also investigated the effect of constructions on the derivative of the equation of state , cosmic density parameter, CMB power spectrum , and matter spectra . We also found that the Hubble tension may be related to the reionization process.

Interfacial assembly and properties of amphiphilic polymer-grafted nanoparticles: Effect of chemical design and density of grafted polymers

Despite extensive research conducted on the polymer-grafted nanoparticle (PGNP) systems for the development of emulsifiers with enhanced performance, little is known about the effects of the grafting architecture and density on the interfacial assembly and interfacial tension reduction behavior of the oil/water (O/W) interface at the molecular level. We performed coarse-grained molecular simulations of both biphasic and emulsion droplet systems with emulsifiers, including Janus (grafting of hydrophilic (HI) and hydrophobic (HO) homopolymers onto two regions of the surface), HI–HO (grafting of diblock polymers with HI monomers as inner blocks and HO monomers as outer blocks), and HO–HI PGNPs, for various graft densities and volume fractions of PGNPs. Compared with the diblock PGNPs, the grafted HI and HO homopolymers of Janus PGNPs penetrate the oil or water phase, rather than assembling at the O/W interface. The depletion of the interface of grafted polymers increases the interfacial tension; consequently, the Janus PGNPs are not effective in reducing the interfacial tension for all the investigated graft densities. The interfacial assembly behavior of the HI–HO and HO–HI PGNPs, whose insoluble blocks have asymmetric interactions with the O/W phases, depends on the graft density and volume fraction. This is particularly the case for their dispersibility, which is an important factor for the interfacial tension. At low graft density, we observe a uniform distribution of HO–HI PGNPs at the O/W interface, resulting in an effective reduction in interfacial tension. At high volume fractions of PGNPs with high graft density, a more tightly packed distribution is observed between HO–HI PGNPs than between HI–HO PGNPs, and their changes in assembly behavior reverse the rate of decrease in the interfacial tension of HO–HI and HI–HO PGNPs. Our results indicate that the grafting architectures of diblock polymers have a significant influence on the assembly behavior at the interface and interfacial tension, and that the appropriate grafting architecture for effective emulsifiers that stabilize the interfaces is different depending on the graft density and volume fraction of the PGNPs. This study also provides new insights into the relation between the interfacial assembly and the stability of emulsion droplets covered by the PGNPs. We observe that the diblock PGNPs, which have the insoluble block as the inner block, are more promising candidates for stabilizing emulsions compared with Janus PGNPs. In the opposite case, the insoluble blocks become the “sticky” points for the adhesion of emulsion droplets, resulting in droplet–droplet coalescence even for effective emulsifiers in reducing interfacial tension. The findings of this study offer a theoretical guide for designing optimal PGNPs for specific volume fractions and optimal graft densities and volume fractions for the grafting architectures of synthesizable PGNPs, and they support the progression from the trial-and-error empirical approaches for developing improved emulsifiers.

Investigating the Relationship Between Cannabis Expectancies and Anxiety, Depression, and Pain Responses After Acute Flower and Edible Cannabis Use.

Objective: Cannabis has been touted for a host of pharmacological and therapeutic effects and users commonly report reduced symptoms of physical and mental health conditions, including anxiety, depression, and chronic pain. While there is existing empirical evidence supporting these effects of cannabis use, little is known about the extent to which these effects result from pharmacological versus expectancy factors. We evaluated the associations between participants' cannabis expectancies and their acute self-reported reactions after using legal market forms of cannabis with varying levels of cannabidiol (CBD) and Δ9-tetrahydrocannabinol (THC) in three domains: anxiety, depression, and pain. Methods: Fifty-five flower and 101 edible cannabis users were randomly assigned and asked to purchase at a local dispensary one of three products containing varying levels of CBD and THC. Participants completed a baseline assessment where they reported expectancies about general health effects of cannabis use and an experimental mobile laboratory assessment where they administered their assigned products. Edible users also reported their domain-specific expectancies about cannabis use in improving anxiety, depression, and pain. Following administration, participants completed acute indicators of anxiety, depression, and pain operationalized through subjective acute tension, elation, and a single-item measure of pain. Results: Among flower users, more positive expectancies for cannabis to improve general health were correlated with greater reductions in tension at acute post-use. This finding was replicated among edible users. Unlike flower users, more positive expectancies for cannabis to improve general health were also correlated with greater increases in elation and greater reductions in pain among edible users. More positive expectancies for cannabis to improve depression and pain were also correlated with greater increases in elation and greater reductions in pain, respectively, among edible users. Conclusions: Cannabis users' expectancies significantly impacted some of the acute subjective effects of legal market cannabis products. Among both flower and edible users, consistent, significant expectancy effects were found. Results were consistent with prior findings and demonstrate the need to measure and control pre-existing expectancies in future research that involves cannabis administration. Clinical trial registration number: NCT03522103.

Using Subcritical Water to Obtain Polyphenol-Rich Extracts with Antimicrobial Properties.

The use of green extraction methods that meet the criteria of sustainable and environmentally friendly technologies has been increasing in recent decades due to their many benefits. In this respect, extracts obtained using subcritical water are also gaining increased attention because of their potential antioxidant and antimicrobial properties. Their antimicrobial activity is mainly due to the presence of various polyphenolic compounds. Although the exact mechanism of the antibacterial action of polyphenolic compounds has not yet been fully investigated and described, polyphenols are known to affect the bacterial cell at several cellular levels; among other things, they cause changes and ruptures in the cell membranes of the bacterial cell, affect the inactivation of bacterial enzymes and damage bacterial DNA. The difference in the strength of the antimicrobial activity of the extracts is most likely a result of differences in their lipophilicity and in the number and position of hydroxyl groups and double bonds in the chemical structure of polyphenols. By changing the extraction conditions, especially the temperature, during subcritical water extraction, we affect the solubility of the compounds we want to extract. In general, as the temperature increases, the solubility of polyphenolic compounds also increases, and the reduction of the surface tension of subcritical water at higher temperatures also enables faster dissolution of polyphenolic compounds. Different bacterial strains have different sensitivity to different extracts. However, extracts obtained with subcritical water extraction demonstrate strong antimicrobial activity compared to extracts obtained with conventional methods.

МІНІМІЗАЦІЯ МІЖКЛІТЬОВОГО НАТЯГУ НА БЕЗПЕРЕРВНИХ СТАНАХ ЗА ЯКІРНИМИ СТРУМАМИ ЕЛЕКТРОПРИВОДІВ ПРОКАТНИХ КЛІТЕЙ

In the conditions of continuous rolling of graded profiles with no or too little metal deflection between adjacent rolling cages, the most promising is tension regulation based on information about the armature currents of the main electric drives. The effectiveness of the method of minimizing the tension of graded rolled products based on information about the armature currents of the main electric drives was investigated. The method is based on the hypothesis of the constant ratio of the armature current of the drive of the next cage to the armature current of the drive of the previous cage in the free rolling mode. The method involves predicting the free-rolling current in rolling electric drives based on information about the free-rolling current in the electric drives of previous cages. The study is based on a complex model of the process of continuous bar rolling in four finishing cages of a small-grade mill with individual electric drives equipped with subordinate speed control systems. Given the fundamental impossibility of approbation of the proposed method by the methods of an industrial experiment, verification of its operability requires computer simulation modeling. The created computer model allows for adequate simulation of the operation of the control system in the conditions of rolling in a continuous group of cages with an accuracy that is sufficient for conclusions about the effectiveness of its operation. According to the results of the study of the control system by means of computer simulation, the effectiveness of its work was proven, in particular, the reduction of the specific tension in all intercell spaces of the finishing group of roll stands to an acceptable level of 10 N/mm2 and a significant narrowing of the range of changes in the width of the finished rolled product.

Oil/Brine Screening for Improved Fluid/Fluid Interactions during Low-Salinity Water Flooding

Low-salinity water flooding/smart water flooding (LSWF/SWF) are used for enhanced oil recovery (EOR) because of the improved extraction efficiency. These methods are more environmentally friendly and in many scenarios more economical for oil recovery. They are proven to increase recovery factors (RFs) by between 6 and 20%, making LSWF/SWF technologies that should be further evaluated to replace conventional water flooding or other EOR methods. Fluid/fluid interaction improvements include interfacial tension (IFT) reduction, viscoelastic behavior (elastic properties modification), and microemulsion generation, which could complement the main mechanisms, such as wettability alteration. In this research, we evaluate the importance of fluid/fluid mechanisms during LSWF/SWF operations. Our study showed that a substantial decrease in IFT occurs when the oil asphaltene content is in the range of 0% to 3 wt.%. An IFT reduction was observed at low salinity (0–10,000 ppm) and a specific oil composition condition. Optimal IFT occurs at higher divalent ion concentrations when oil has low asphaltene content. For the oil with high asphaltene content, the sulfates concentration controls the IFT alteration. At high asphaltene concentrations, the formation of micro-dispersion is not effective to recover oil, and only a 5% recovery factor improvement was observed. The presence of asphaltene at the oil/low-salinity brine interface increases the energy required to disrupt it, inducing significant changes in the elastic moduli. In cases of low asphaltene content, the storage modulus demonstrates optimal performance at higher divalent concentrations. Conversely, at high asphaltene concentrations, the dominant factors to control the interface are paraffin content and temperature.

Synthesis, performance and mechanism of shrinkage-reducing agents with water-reducing function for cement-based materials

Three shrinkage-reducing agents (SRAs) possessing a water-reducing capacity with different structures were synthesized by aqueous free radical copolymerization. Their structures were characterized by Gel Permeation Chromatography (GPC), specific anion charge density, and Fourier Transform Infrared Spectrometer (FTIR) measurements. Their abilities to reduce surface tension and their adsorption and dispersing effectiveness in cement paste as well as their impacts on cement hydration and compressive strength, autogenous shrinkage, drying shrinkage, and pore structure of cement mortar were investigated. Results clearly showed that the three synthesized SRAs with a water-reducing function reduced the surface tension of pore solution, with the water-reducing SRA with butyl exerting the most significant effect due to its lower molecular mass. They enhanced the flowability of cement paste because of their adsorption on cement grains. The water-reducing SRA with dimethyl amino exhibited higher adsorption amounts on cement grains due to higher charge density, resulting in higher initial flowability of cement paste and more significant hydration retardation. Their presence decreased the autogenous shrinkage of cement mortar by reducing the surface tension of pore solution, delaying the cement hydration, and decreasing the capillary pore volume. Their addition also mitigated the drying shrinkage due to the synergistic effect of surface tension reduction, pore structure coarsening, and porosity (2.5–50 nm) reduction. Among the three, the water-reducing SRA with butyl demonstrated a higher capability of reducing the drying shrinkage and had a favorable effect on the compressive strength of mortar at later ages.

Advances in the production of biosurfactants as green ingredients in home and personal care products.

Home and personal care industry is currently witnessing a growing demand for sustainable and eco-friendly alternatives to synthetic surfactants. This increase is fueled by concerns over the delayed degradation and environmental impact of the latter. To this, biosurfactants possess important properties such as biodegradability, low toxicity, and renewable sourcing. These qualities position them as compelling replacements of traditional synthetic surfactants. Their diverse attributes including emulsification, antimicrobial efficacy, surface tension reduction, and foaming capability, make them well-suited choices for home and personal care products. Biosurfactants can be produced through several inexpensive and renewable sources which contributes to their commercialization potential. This article discusses various microbial derived biosurfactants including rhamnolipids, sophorolipids, mannosyl-erythritol lipids, trehalolipids and lipopeptides, unraveling and comparing their distinctive roles and advantages in the home and personal care industry. It also focuses on the recent patent innovations in the production of biosurfactants which have aimed at improving their economic viability and performance attributes. Finally, the article sheds light on the challenges and future trajectories for better integration of these sustainable biosurfactants into mainstream consumer products.

Mutual role of dodecylbenzene sulfonic acid on enhanced oil recovery and asphaltene inhibition in low salinity medium: Experimental and XDLVO study

Understanding the molecular interactions during oil recovery processes can shed light on screening new chemicals for future operations. Of particular interest are chemicals capable of providing the mutual role of asphaltene inhibition and interfacial tension reduction at liquid–liquid and rock-liquid interfaces. This study delves into the interfacial interactions between low-salinity brines, model oils containing dodecylbenzene sulfonic acid, and dolomite rock surfaces. In the experimental part, the asphaltene precipitation inhibition efficacy of dodecylbenzene sulfonic acid was evaluated through filtration and precipitation test, and its oil recovery performance was examined from interfacial tension reduction and wettability alteration viewpoints. The theoretical part was then followed by the implementation of the surface energy concept based on the XDLVO theory, where acid-base and Lifshitz-van der Waals interaction energies, as well as the work of cohesion/adhesion between interacting bodies in asphaltene and oil recovery systems, were considered. The results obtained from this study revealed that dodecylbenzene sulfonic acid, owing to its acidic nature and the long alkyl chain in its structure, could simultaneously perform the role of asphaltene inhibitor and oil recovery agents. In particular, asphaltene particles showed less tendency to aggregate and form macrostructures in the presence of low-salinity brines formulated with magnesium chloride. The total interaction energy between asphaltene particles was almost halved by the addition of dodecylbenzene sulfonic acid. The low interfacial tension of 0.16 mN/m between model oil containing 1 wt% of DBSA and low-salinity brine containing 5000 mg/L magnesium chloride and the wettability alteration of the dolomite sample toward water-wetness were also confirmed by theoretical calculations using the concept of work of adhesion.

Analysis of metallurgical defects in enamel steel castings

Abstract The relevant experiments and studies were conducted to address the metallurgical defects such as subcutaneous bubbles and slag inclusions occurring during the enamel steel continuous casting process. According to the high-temperature experimental results, calculations were made to determine the changes in viscosity and tension due to the steel reaction with the slag. Based on the experimental findings, there was a notable variation in the content of SiO2 and Al2O3 in the slag before and after the reaction. The concentration of the element Al in the steel melt significantly decreased, whereas the concentration of Ti showed a minimal change. These observations indicate that the reduction of SiO2 at the slag–steel interface is predominantly attributed to the role of Al. The calculation results showed that at 300 s of reaction time, the viscosity rapidly increased from 0.108 to 0.133 Pa·s and then slowly increased to 0.155 Pa·s; The interfacial tension rapidly decreased from its initial value of 1,380 mJ·m−2 to a minimum of 1,320 mJ·m−2, and it then slowly increased to an equilibrium state. Therefore, the main cause of the occurrence of porosity defects in the enamel steel continuous casting process is the reduction of interfacial tension between slag, steel, and gas caused by the reaction between the slag and steel, as well as the foaming of the slag.

INTERFACIAL TENSION AND CONTACT ANGLE TESTS OF RHAMNOLIPIDS AND SOPHOROLIPIDS IN SANDSTONE FOR ENHANCED OIL RECOVERY

In the context of the development of enhanced oil recovery technology, biotechnology can be used to develop new methods that are more environmentally friendly and sustainable, one of which is the use of biosurfactants. Rhamnolipids and sophorolipids are non-toxic biosurfactants, biodegradable, and environmentally favorable substances. This study compares the results of laboratory studies on fluid-to-fluid interactions, including the interfacial tension and rock wetness tests at various concentrations and salinities, which represent high salinity, medium salinity, and low salinity. The mechanism of these two biosurfactants is based on reducing the interfacial tension (IFT) between the fluids and changing the wettability of the rock to a more water-wet state. In the interfacial tension test, the reduction in the interfacial tension of rhamnolipids reached 10-2 mN/m, while that of sophorolipids only reached 10-1 mN/m. Then, the sandstone wettability test showed that the two biosurfactants were classified as water-wet (<75°). This happens because of its chemical structure, which has two parts: the hydrophobic part and the hydrophilic part. Within the salinity range of 8,000-32,000 ppm, the rhamnolipids work better in the higher salinity to reduce interfacial tension, and the salinity has a subtle effect on the contact angle. On the other hand, sophorolipids were not affected by salinity for both interfacial tension and contact angle. These two biosurfactants have the potential to increase oil recovery in sandstone so that they can contribute to environmentally friendly biotechnology.

Performance evaluation of rhamnolipid biosurfactant produced by Pseudomonas aeruginosa and its effect on marine oil-spill remediation.

This study aimed to reveal that the effect of biosurfactant on the dispersion and degradation of crude oil. Whole genome analysis showed that Pseudomonas aeruginosa GB-3 contained abundant genes involved in biosurfactant synthesis and metabolic processes and had the potential to degrade oil. The biosurfactant produced by strain GB-3 was screened by various methods. The results showed that the surface tension reduction activity was 28.6 mN·m-1 and emulsification stability was exhibited at different pH, salinity and temperature. The biosurfactant was identified as rhamnolipid by LC-MS and FTIR. The fermentation conditions of strain GB-3 were optimized by response surface methodology, finally the optimal system (carbon source: glucose, nitrogen source: ammonium sulfate, C/N ratio:16:1, pH: 7, temperature: 30-35°C) was determined. Compared with the initial fermentation, the yield of biosurfactant increased by 4.4 times after optimization. In addition, rhamnolipid biosurfactant as a dispersant could make the dispersion of crude oil reach 38% within seven days, which enhanced the bioavailability of crude oil. As a biostimulant, it could also improve the activity of indigenous microorganism and increase the degradation rate of crude oil by 10-15%. This study suggested that rhamnolipid biosurfactant had application prospect in bioremediation of marine oil-spill.

The potency of hydrophobic modification of alginate for a self-assembly matrix in fish oil encapsulation

To act as an emulsifier and a matrix for fish oil encapsulation, alginate is required to be modified due to its hydrophilicity. The purpose of this study was to modify alginate using dodecenyl succinic anhydride (DSA) under pH-controlled conditions and to apply it for stabilizing emulsion and encapsulating fish oil. The modification that followed the first-order reaction improved the hydrophobic properties of alginate as shown by the reduction of surface tension but improving the water contact angle, with CMC of 0.18 mg/l. A higher concentration of modified alginate was better in stabilizing fish-oil emulsion than the native one, as supported by the results of zeta potential, viscosity, and droplet size of the emulsion. Freeze-dried particle of this modified alginate emulsion showed better encapsulation efficiency and oxidation protection ability. Thermal properties of alginate were changed after hydrophobic modification and oil encapsulation. The freeze-dried particles of this modified alginate emulsion showed better encapsulation efficiency and protection ability. This study confirmed the protective ability of the modified alginate using DSA as an oil-based active ingredient encapsulant.

Production, characterization and biomedical potential of biosurfactants produced by haloalkaliphilic archaea from Wadi El-Natrun, Egypt

Extreme halophilic archaea that can live in high saline environments can offer potential applications in different biotechnological fields. This study delves into the fascinating field of halophilic archaea and their ability to produce biosurfactants. Some strains of haloarchaea were isolated from Wadi El-Natrun and were screened for biosurfactants production in a standard basal medium using emulsification index assay. Two strains were chosen as the potential strains for surface tension reduction. They were identified as Natrialba sp. BG1 and N3. The biosurfactants production was optimized and the produced emulsifiers were partially purified and identified using FTIR and NMR. Sequential statistical optimization, Plackett–Burman (PB) and Box–Behnken Designs (BBD) were carried out using 5 factors: oil, NaCl, casamino acids, pH, and inoculum size. The most significant factors were used for the next Response Surface Methodology experiment. The final optimal conditions for biosurfactants production were the inoculum size 2% pH 11 and NaCl 250 g/L, for Natrialba sp. BG1 and inoculum size 2.2%, pH 10 and NaCl 100 g/L for Natrialba sp. N3. The produced biosurfactants were tested for wound healing and the results indicated that Natrialba sp. BG1 biosurfactants is more efficient than Natrialba sp. N3 biosurfactants. Biosurfactants extracts were tested for their cytotoxic effects on normal cell line as well as on different cancer cells using MTT assay. The findings demonstrated that varying concentrations of the biosurfactants (31.25, 62.5, 125, 250, 500 and 1000 µg/mL) exhibited cytotoxic effects on the cell lines being tested. Additionally, the outcomes unveiled the presence of anti-inflammatory and antioxidant properties for both biosurfactants. Consequently, they could potentially serve as natural, safe, and efficient novel agents for combating cancer, promoting wound healing, and providing anti-inflammatory and antioxidant benefits.

Interfacial Behaviors and Oil Detachment Mechanisms by Modified Silica Nanoparticles: Insights from Molecular Simulations.

Surfactant flooding has been considered as a promising approach for chemically enhanced oil recovery (EOR). However, this technique encounters several limitations, such as high costs, environmental concerns, and reduced efficiency under high-temperature and high-salinity reservoir conditions. Recently, nanoparticles have also been proposed as an alternative for EOR due to their superior properties compared with surfactants. This research employs molecular dynamics simulations to explore the impact of modified SiO2 nanoparticles on oil-water interfacial behaviors and the detachment of oil droplets from an oil-wet surface. The simulation results reveal that modified nanoparticles, featuring hydrophilic and hydrophobic functional groups, have slight impacts on interfacial tension reduction of the oil-water interface. Nanoparticles with varying degrees of modification exhibit distinct positions within the interface, consequently influencing the thickness of the interfacial layer. Notably, the interactions among the nanoparticles, oil molecules, and surface facilitate the formation of a water channel, thereby enhancing the process of oil detachment. Comparative analysis indicates that in terms of oil displacement efficiency, the thickness of the interfacial layer has a more significant impact than interfacial tension reduction. Furthermore, to elucidate the mechanisms of modified nanoparticles enhancing the oil recovery rate, the interaction energies among the oil droplet, nanoparticles, water, and surface are analyzed. The molecular-level insights derived from this investigation could provide valuable guidance for the design of modified nanoparticles tailored to EOR applications.

Stabilizing effect of silver carp myofibrillar protein modified by high intensity ultrasound on high internal phase emulsions: Protein denaturation, interfacial adsorption and reconfiguration

This study evaluated the impact of high intensity ultrasound (HIU) on myofibrillar proteins (MP) from silver carp, and investigated the stabilizing effect of HIU-treated MP (UMP) on high internal phase emulsions (HIPEs). Ultrasonic cavitation induced protein denaturation by decreasing size and unfolding conformation, to expose more hydrophobic groups, particularly UMP at 390 W, showing the smallest particle size (181.71 nm) and most uniform distribution. These structural changes caused that UMP under 390 W exhibited the highest surface hydrophobicity, solubility (92.72 %) and emulsibility (115.98 m2/g and 70.4 min), all of which contributed to fabricating stable HIPEs with oil volume fraction up to 0.8. UMP-based HIPEs possessed tightly packed gel network and self-supporting appearance due to the adsorption of numerous proteins at the oil-water interface and the reduction of interfacial tension by protein reconfiguration. The larger interface coverage reinforced cross-linking between interfacial proteins, thus increasing the viscoelasticity and recoverability of HIPEs, also the resistance to centrifugal force, high temperature (90 °C, 30 min) and freeze-thaw cycles. These findings furnished insightful perspectives for MP deep processing through HIU, expanding the high-value application of UMP-based HIPEs in fat replacer, nutritional delivery system with high encapsulation content and novel 3D printing ink.

Forecasting the Problem of Excessive Oil Entrainment in a Desalter Using Spinning Drop Method.

Frequent desalter upsets in the refineries processing opportunity crude oils are often triggered by a rapid and uncontrollable buildup of the rag layer, a thick water-in-oil emulsion, at the oil-brine interface. This is caused by spontaneous emulsification of brine in oil. This study investigates a unique observation from a spinning drop (SD) tensiometer, revealing the low apparent interfacial tension and rigidity of SD caused by spontaneous emulsification. Fine droplets of brine generated through spontaneous emulsification decorate the SD surface and form a stable, low-energy bilayer. Simulated rag layers using the brines from upset incidences exhibit similar behavior, indicating that spontaneous emulsification is driven by chemical species in brine, which promote osmotic water transport. The rate of rag layer buildup correlates with the rate of spontaneous emulsification, with the temperature coefficient of interfacial tension reduction serving as a sensitive indicator. An imminent upset in the operation can be forecasted by measuring this temperature coefficient, enabling preventive measures.