Rechargeable Lithium Metal Batteries Research Articles

Dynamically reversible cross-linked polymer electrolytes with highly ionic conductivity for dendrite-free lithium metal batteries

High-safety PEO-based electrolytes have attracted widespread attention, but their inefficient conduction of Li ions and poor contact with electrode interfaces deteriorate the performances of rechargeable lithium metal batteries. Herein, we design a vitrimer polymer electrolyte (V-SPE-PEG) with abundant dynamic imine bonds via Schiff base reaction between aldehyde and ammonia, which achieves high ionic conductivity and good interfacial compatibility with lithium anode. The dynamic polymer network in V-SPE-PEG exhibits solid-state plasticity because reversible imine bonding reactions enable the integrity of the polymer network to be maintained while altering the cross-linked points under external stimuli. Therefore, this 3D dynamic cross-linked network effectively facilitates the polymer chain dynamics and meanwhile enhances ionic conductivity. Additionally, dynamic bond exchange fosters electrolyte flowability and self-healing during lithium deposition, promoting a tightly integrated electrode/electrolyte interface while inhibiting lithium dendrites growth. Consequently, lithium symmetric cells utilizing the V-SPE-PEG electrolyte demonstrate exceptional long-term cycling stability, surpassing 1100 h and exhibit outstanding ionic conductivity of 2.7 × 10−4 S cm−1 at 30 °C. The LiFePO4||Li battery maintains stable cycling performance at both 40 °C and 60 °C. This study introduces an innovative approach to designing solid-state electrolytes for lithium-metal batteries.

An ultrathin and robust single-ion conducting interfacial layer for dendrite-free lithium metal batteries

The practical application of rechargeable lithium metal batteries (LMBs) encounters significant challenges due to the notorious dendrite growth triggered by uneven Li deposition behaviors. In this work, a mechanically robust and single-ion-conducting interfacial layer, fulfilled by the strategic integration of flexible cellulose acetate (CA) matrix with rigid graphene oxide (GO) and LiF fillers (termed the CGL layer), is rationally devised to serve as a stabilizer for dendrite-free lithium (Li) metal batteries. The GCL film exhibits favorable mechanical properties with high modulus and flexibility that help to relieve interface fluctuations. More crucially, the electron-donating carbonyl groups (C=O) enriched in GCL foster a strengthened correlation with Li+, which availably aids the Li+ desolvation process and expedites facile Li+ mobility, yielding exceptional Li+ transference number of 0.87. Such single-ion conductive properties regulate rapid and uniform interfacial transport kinetics, mitigating the growth of Li dendrites and the decomposition of electrolytes. Consequently, stable Li anode with prolonged cycle stabilities and flat deposition morphologies are realized. The Li||LiFePO4 full cells with CGL protective layer render an outstanding cycling capability of 500 cycles at 3 C, and an ultrahigh capacity retention of 99.99% for over 220 cycles even under harsh conditions. This work affords valuable insights into the interfacial regulation for achieving high-performance LMBs.

Coconstruction of Supramolecular Lithium-Conducting Cross-Linked Networks Based on PVDF and Triblock Polymer Nanomicrosphere Solid-State Polymer Electrolytes for Lithium-Metal Batteries.

Uneven lithium plating and low ionic conductivity currently impede the realization of high-capacity rechargeable lithium metal batteries. And the conventional poly(ethylene oxide) (PEO) solid-state electrolytes are unsuitable for high-energy-density Li anode applications due to their low lithium-ion transference number and high reactivity with Li metal, leading to detrimental dendrite formation and potentially hazardous exothermic reactions with the electrolyte. In this study, we employ a supramolecular approach to develop a novel polymer solid-state electrolyte based on poly(vinylidene fluoride) (PVDF) and a novel triblock polymer nanomicrosphere, (poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone), (PCL-PEG-PCL). The abundance of carbonyl and ether-oxygen functional groups in PCL-PEG-PCL enhances the lithium coordination environment within the polymer solid-state electrolyte. Additionally, the original C-F moieties of PVDF form hydrogen bonds with C-H and terminal hydroxyl groups in PCL-PEG-PCL, collectively creating a multichannel fast Li+-conducting supramolecular cross-linked network. The resulting electrolyte demonstrates a high ionic conductivity of 1.4 × 10-3 S cm-1 and an extended electrochemical window of 5.2 V. Moreover, the electrolyte exhibits a high lithium-ion transference number (tLi+ = 0.63) at room temperature and exhibits excellent interfacial compatibility with the lithium metal anode. For the resulting electrolyte utilized in LiFePO4 batteries, the capacity retention of the cells assembled with this electrolyte exceeds 91.3% after 1000 cycles at 25 °C and 2 C (0.281 mA cm-2).

Scalable Customization of Crystallographic Plane Controllable Lithium Metal Anodes for Ultralong-Lasting Lithium Metal Batteries.

A formidable challenge to achieve the practical applications of rechargeable lithium (Li) metal batteries (RLMBs) is to suppress the uncontrollable growth of Li dendrites. One of the most effective solutions is to fabricate Li metal anodes with specific crystal plane, but still lack of a simple and high-efficient approach. Herein, a facile and controllable way for the scalable customization of polished Li metal anodes with highly preferred (110) and (200) crystallographic orientation (donating as polished Li(110) and polished Li(200), respectively) by regulating the times of accumulative roll bonding, is reported. According to the inherent characteristics of polished Li(110)/Li(200), the influence of Li atomic structure on the electrochemical performance of RLMBs is deeply elucidated by combining theoretical calculations with relative experimental proofs. In particular, a polished Li(110) crystal plane is demonstrated to induce Li+ uniform deposition, promoting the formation of flat and dense Li deposits. Impressively, the polished Li(110)||LiFePO4 full cells exhibit unprecedented cycling stability with 10000 cycles at 10 C almost without capacity degradation, indicating the great potential application prospect of such textured Li metal. More valuably, this work provides an important reference for low-cost, continued, and large-scale production of Li metal anodes with highly preferred crystal orientation through roll-to-roll manufacturability.

Porous Organic Framework Materials (MOF, COF, and HOF) as the Multifunctional Separator for Rechargeable Lithium Metal Batteries.

The separator is an important component in batteries, with the primary function of separating the positive and negative electrodes and allowing the free passage of ions. Porous organic framework materials have a stable connection structure, large specific surface area, and ordered pores, which are natural places to store electrolytes. And these materials with specific functions can be designed according to the needs of researchers. The performance of porous organic framework-based separators used in rechargeable lithium metal batteries is much better than that of polyethylene/propylene separators. In this paper, thethree most classic organic framework materials (MOF, COF, and HOF) are analyzed and summarized. The applications of MOF, COF, and HOF separators in lithium-sulfur batteries, lithium metal anode, and solid electrolytes are reviewed. Meanwhile, the research progress of these three materials in different fields is discussed based on time. Finally, in the conclusion, the problems encountered by MOF, COF, and HOF in different fields as well as their future research priorities are presented. This review will provide theoretical guidance for the design of porous framework materials with specific functions and further stimulate researchers to conduct research on porous framework materials.

Electrospun MoS2-CNTs-PVA/PVA Hybrid Separator for High-Performance Li/FeS2 Batteries.

As a promising candidate for high-energy-density rechargeable lithium metal batteries, Li/FeS2 batteries still suffer from the large volume change and severe shuttle effect of lithium polysulfides during cycling. To improve the electrochemical performance, great efforts have been made to modify FeS2 cathodes by constructing various nanocomposites. However, energy density is sacrificed, and these materials are not applicable at a large scale. Herein, we report that the electrochemical performance of commercial FeS2 can be greatly enhanced with the application of a double-layer MoS2-CNTs-PVA (MCP)/PVA separator fabricated by electrospinning. The assembled Li/FeS2 batteries can still deliver a high discharge capacity of 400 mAh/g after 200 cycles at a current density of 0.5 C. The improved cycling stability can be attributed to the strong affinity towards lithium polysulfides (LiPSs) of the hydroxyl-rich PVA matrix and the unique double-layer structure, in which the bottom layer acts as an electrical insulation layer and the top layer coupled with MoS2/CNTs provides catalytic sites for LiPS conversion.

Engineering a lithium silicate-based artificial solid electrolyte interphase for enhanced rechargeable lithium metal batteries

The main motivation for replacing lithium-ion batteries with lithium metal batteries is to achieve a higher energy density by using the metallic lithium anode. One of the major challenges with rechargeable lithium metal batteries is the formation of lithium dendrites and dead lithium during repeated cycling. Another challenge is the formation of the unstable solid electrolyte interphase (SEI) on the surface of the lithium metal electrode, which can reduce battery efficiency and cycle life. In the present work, two different lithium silicates (Li2Si2O5 and Li2SiO3) are successfully synthesized and implemented as an artificial SEI layer via a simple dry coating method. The lithium silicate coating acts as a protective barrier that prevents direct contact between the lithium metal and the electrolyte, which can cause undesirable side reactions and reduce the efficiency and lifetime of the battery. The lithium silicate artificial SEI layer improves the stability of lithium metal batteries by reducing unwanted surface reactions, optimizing ion transport kinetics, and protecting the lithium metal anode from mechanical deformation and unstable SEI formation during extended cycling. This laminated lithium anode structure can be an effective design for the future development of rechargeable lithium metal batteries.

Designing an Air-Stable Interphase on Lithium Metal Anode to Improve Cycling Performance.

The application of rechargeable lithium metal batteries is challenged by intractable issues of uncontrollable Li dendrite growth that result in poor cycle life and safety risks. In this work, an air-stable interphase is developed to protect the lithium metal anode (LMA) via a facile solution-based approach. The Ag-embedded fluoride-rich interphase not only creates abundant lithiophilic sites for homogenizing Li nucleation and growth but also resists severe air erosion to protect the LMA beneath and enable decent cycling stability. As a result, the Ag-F-rich interphase enables flat Li deposition on LMA, which is clearly observed in the operando Li plating experiments. Paired with a LiFePO4 cathode (11.8 mg cm-2), the Ag-F-rich interphase-modified LMA enables 300 stable cycles at 0.5 C, delivering a capacity retention ratio as high as 91.4%. Even after being exposed to air for 1 h, the modified LMA still runs smoothly for over 120 cycles with ignorable capacity decay, exhibiting great air stability. This work proves the concept of functionalizing the interphase on the LMA to enable good cycling performance even under severe air erosion.

Deciphering the effect of nucleation/growth kinetics on the morphology of Li plating/stripping on vertically aligned carbon nanofibers - A low-tortuosity 3-D nanostructured carbon host

Reversible lithium metal anodes (LMAs) are the holy grail for future rechargeable lithium metal batteries. Three-dimensional (3-D) conductive hosts have been extensively explored as an effective approach to suppressing dendrite formation and enabling reversible Li plating/stripping. However, the microscopic morphologies of Li plating and their correlation with the cell performance are not clear. Herein we unravel these issues using the vertically aligned carbon nanofiber (VACNF) array as a model 3-D conductive carbon host which has a well-defined vertical low-tortuosity structure allowing observation of the intrinsic Li morphologies infiltrated into the 3-D host. The VACNF array indeed provides much higher stability and reversibility for Li plating/stripping due to its high surface area and lithiophilic properties. We found that Li plating on both VACNF array and planar Cu electrodes follows the classical nucleation and growth model. Though the low plating current density (≤0.10 mA/cm2) provides better cycling stability consistent with the Sand’s equation, it forms sparse irregular grains stacked with dendrite-like long Li fibers. In contrast, the moderate to high plating current densities (1.0 − 5.0 mA/cm2) produce more uniform Li morphologies consisting of smaller micro-columns or micro-spheres. By decoupling the plating and stripping current densities, we unravel that the more uniform micro-columnar Li infiltrated in the VACNF array obtained at the moderate plating current density (∼1.0 mA/cm2) indeed exhibits the highest cycling performance. This provides new insights into the relationship between macroscopic electrochemical tests and microscopic Li morphologies, aiding in optimizing the performance of LMAs based on 3-D conductive hosts.

Advanced Electrolytes for Rechargeable Lithium Metal Batteries with High Safety and Cycling Stability

Advanced Electrolytes for Rechargeable Lithium Metal Batteries with High Safety and Cycling Stability

Interfacial solvation-structure regulation for stable Li metal anode by a desolvation coating technique

Rechargeable lithium (Li) metal batteries face challenges in achieving stable cycling due to the instability of the solid electrolyte interphase (SEI). The Li-ion solvation structure and its desolvation process are crucial for the formation of a stable SEI on Li metal anodes and improving Li plating/stripping kinetics. This research introduces an interfacial desolvation coating technique to actively modulate the Li-ion solvation structure at the Li metal interface and regulate the participation of the electrolyte solvent in SEI formation. Through experimental investigations conducted using a carbonate electrolyte with limited compatibility to Li metal, the optimized desolvation coating layer, composed of 12-crown-4 ether-modified silica materials, selectively displaces strongly coordinating solvents while simultaneously enriching weakly coordinating fluorinated solvents at the Li metal/electrolyte interface. This selective desolvation and enrichment effect reduce solvent participation to SEI and thus facilitate the formation of a LiF-dominant SEI with greatly reduced organic species on the Li metal surface, as conclusively verified through various characterization techniques including XPS, quantitative NMR, operando NMR, cryo-TEM, EELS, and EDS. The interfacial desolvation coating technique enables excellent rate cycling stability (i.e., 1C) of the Li metal anode and prolonged cycling life of the Li||LiCoO2 pouch cell in the conventional carbonate electrolyte (E/C 2.6 g/Ah), with 80% capacity retention after 333 cycles.

Three-dimensional copper current collector as an anode for rechargeable anode-less lithium-ion batteries

The formation of dendrites presents a significant challenge that hampers the performance of lithium metal batteries, leading to rapid capacity degradation, low coulombic efficiency, and potential short circuits. In this regard we have engineered a rechargeable lithium metal battery without a conventional anode – lithium, employing commercially available LiNi1/3Co1/3Mn1/3O2 as a cathode and enhanced three-dimensional copper foam current collector as an anode. The modification of the three-dimensional copper foam current collector with gold effectively reduced the local current density while providing a substantial surface area for lithium deposition. Moreover, our approach incorporates a blend of salts, namely lithium bis(trifluoromethanesulfonyl)imide and lithium difluoro(oxalato)borat, resulting in an impressive reversible capacity of 100 mAh g−1 with an outstanding coulombic efficiency of 99.9% after 50 cycles. These discoveries hold particular significance in the advancement of next-generation energy storage systems characterized by high energy density and immunity to dendrite formation.

Trilithium salt of tetrahydroxyanthraquinone: A high-voltage and stable organic cathode material for rechargeable lithium metal and lithium-ion batteries

Organic cathode materials (OCMs) have drawn considerable attention for lithium batteries but suffer from unfavorable dissolution problem and thus inferior cycling performance. Salification is a simple approach to restrain the dissolution but most reported lithium-salt-type OCMs are still unable to achieve good cycling stability due to poorly conjugated and/or asymmetric structure. Herein, we report a novel air-stable, largely conjugated, and symmetric organic lithium salt synthesized from 1,4,5,8-tetrahydroxyanthraquinone (THAQ), namely Li3THAQ. It possesses a layered crystalline structure with large interlayer spacings, which is relatively stable in the reversible conversion between Li4THAQ and Li2THAQ. Benefiting from this, Li3THAQ exhibits exceptional electrochemical performance within 2.0–3.6 V, including high reversible capacity (192 mAh g−1), high discharge potential (2.93 V vs. Li+/Li), high rate capability (75 % capacity retention at 5000 mAh g−1 vs. 50 mAh g−1), and high cycling stability (95 % capacity retention after 500 cycles). Additionally, it can be also matched with natural graphite anode to construct a Li-ion full-cell, which was rarely reported for OCMs. In brief, Li3THAQ shows great advantages in structure stability, electrochemical performance, and practicability compared to its counterparts, and the in-depth mechanism understanding provides important insights into the development of lithium-salt-type OCMs.

Performance evaluation of lithium metal rechargeable batteries with a lithium excess cation-disordered rocksalt based positive electrode under high mass loading and lean electrolyte conditions

Operation of 500 W h kg−1 class rechargeable batteries was demonstrated. Non-destructive XCT analysis revealed volume expansion of the lithium metal electrode as the primary reason for the capacity fading.

Lithium Silicates as an Artificial SEI for Rechargeable Lithium Metal Batteries

The major motivation of replacing lithium-ion batteries with lithium metal batteries is to obtain higher energy density by adopting the metallic lithium anode (3860 mAh g-1, theoretically), which means they can store more energy in the same volume or weight. One of the main challenges of rechargeable lithium metal batteries is the formation of lithium dendrites during the charging process.1 Lithium dendrites are tiny needle-like structures that can grow from the surface of the lithium metal electrode and penetrate the separator, causing battery short-circuiting. This can lead to safety issues, including the potential for fire or explosion. Another challenge is the formation of solid-electrolyte interface (SEI) on the surface of the lithium metal electrode, which can reduce the battery's efficiency and cycle life.2 The SEI layer can also lead to the formation of inactive lithium and increase the risk of dendrite growth.In the present work, various lithium silicates have been synthesized to be implemented as the artificial SEI layer via a facile dry coating method.3,4 The lithium silicate coating acts as a protective barrier that prevents direct contact between the lithium metal and the electrolyte, which may cause undesirable side reactions and reduce the efficiency and lifespan of the battery.4 The lithium silicate-based artificial SEI layer improves the stability and efficiency of lithium metal batteries by reducing unwanted surface reactions, improving ion transport kinetics, and protecting the lithium metal anode from mechanical deformation and unstable SEI formation during extended cycling. This laminated lithium anode structure could be an effective design for the future development of long-cycle-life lithium metal batteries. F. Wu et al., Energy Storage Materials, 15, 148–170 (2018).X.-B. Cheng et al., Adv. Sci., 3, 1500213 (2016).A. Bhat, P. Sireesha, Y. Chen, and Y. Su, ChemElectroChem, 9 (2022) https://onlinelibrary.wiley.com/doi/10.1002/celc.202200772.Y.-S. Su, K.-C. Hsiao, P. Sireesha, and J.-Y. Huang, Batteries, 8, 2 (2022). Figure 1

Enhancing Performance of Anode-Free Li-Metal Batteries

Because of their higher energy density, compared to lithium-ion batteries, rechargeable lithium-metalbatteries (LMB) have been considered one of the most attractive next-generation energy-storagesystems (ESS). A promising approach to improving LMB performance, that has gained interest inrecent years, is the use of anode-free lithium-metal batteries (AFLMB). Such battery configurationenables elimination of the problem of using excessive amounts of lithium in LMBs, hence increasingthe specific energy of the battery. This work explores the beneficial effects of integrating metal-oxidenanoparticles (MONPs) into the liquid electrolyte of AFLMB. It was found that the addition of lowconcentrations of MONPs significantly improves coulombic efficiency (CE), capacity retention (CR)and the Solid-Electrolyte-Interphase (SEI) properties. SEM images revealed a smoother lithiummorphology for MONPs cells and XPS analysis showed great differences in the SEI composition. Theresistance of the cell components, extracted via electrochemical impedance spectroscopy (EIS), hasbeen significantly lowered due to the addition of MONPs. The performance of the AFLMB, withoutMONPs, was 97.1% CE and CR of 70% within 12 cycles, while cells with 0.5% SnO2 , 1% Al2O3 and1% TiO2 was 99.1%, 98.8% and 99.4% CE, and CR of 70% within 39, 38 and 36 cycles, respectively.Combinations of two MONPs resulted in 99.9% CE, which is among the highest found in the literaturefor AFLMB.

(Electrodeposition Division Research Award) Electrodeposition as an Enabling Technology in Future Semiconductors, Energy Storage, and Sustainable Metal Production

Electrodeposition is a truly fascinating process. On the one hand, it is highly complex as it entails a myriad of intricately intertwined physiochemical events (transport, kinetics, nucleation, growth, to name a few). Despite this, to a practitioner, electrodeposition can be remarkably simple, easy to control, and safe to operate. Electrodeposition is also extremely versatile, enabling fabrication of various materials (metals, alloys, semiconductors), fabrication onto conductive or resistive substrates, facilitating intricate pattern formation, and providing selectivity in growth. These advantages make electrodeposition a process of choice in a broad range of technologically-important applications: batteries, semiconductor devices, electrometallurgy, and others.1-3 Morphology control is crucial in the industrial practice of electrodeposition. During metallization of nano-scale interconnects in advanced semiconductor devices, metal deposition with near atomic precision is required.1 Similarly, during operation of lithium metal rechargeable batteries, electrodeposition must be controlled to avoid dendritic growth during battery charging.2 Electrodeposition processes in high temperature molten salts, such as those used for electrowinning rare-earth metals, favor spongy deposits which can manifest in entrapment of impurities – here too, controlling morphology is central to overall electrowinning efficacy.3 In this talk, I will discuss and demonstrate how unprecedented morphology control can be achieved in electrodeposition. Such control leverages fundamental understanding of the electrochemical processes at the electrode-electrolyte interface. Specifically, by regulating the electrolyte properties, applied current or potential waveforms, and by employing ‘additives’, the diffusion-reaction processes can be controlled yielding desirable electrodeposit morphologies. Such design of electrodeposition processes is considerably aided by mathematical modeling. I will provide a few examples of how quantitative modeling enables improved process designs in aforementioned applications.During my odyssey in electrodeposition since 2001, I have been fortunate to have exceptional colleagues, collaborators, sponsors, mentors, students and friends, who have made this journey enjoyable and enriching. I am also very thankful for my affiliation to the Electrochemical Society and its electrodeposition division. In my talk, I will provide a few perspectives and anecdotes on how the ECS community has positively impacted me personally and professionally.

Operando Ultrasonic Characterization of Lithium Metal Batteries

Significant progress has been made in understanding and engineering rechargeable lithium metal batteries. Here, I discuss ultrasound as a technique to probe cell-level dynamics for lithium metal batteries in liquid and solid electrolytes. Multiple imaging modalities provide information on physical properties of lithium metal cells, including electrode wetting and consumption, lithium microstructural change and gas evolution. In a first case study, I discuss correlations between ultrasonic transmission signals and lithium microstructure size in liquid electrolytes, as a function of stack pressure and temperature. Anode and cathode effects can be decoupled. In a second case, acoustic amplitude is used to detect void formation in solid-state electrolytes. Third, ultrasound is used to characterize the formation process for various anode-free cells, where the improved chemical and electrochemical stability of localized ether electrolytes is correlated with decreased rates of cell swelling and minimal gas formation. Ultrasonic characterization and imaging is a portable and non-invasive means of probing commercial lithium metal cells after manufacturing, during use, or at the end-of-service.

Polymer/ceramic gel electrolyte with in-situ interface forming enhances the performance of lithium metal batteries

With the introduction of solid-state electrolytes, solid-state lithium-metal batteries face enormous challenges of low electrolyte ion conductivity and high electrode electrolyte interface impedance. Here, we adopt a strategy of combining rigidity and flexibility to design a polymer/ceramic composite gel electrolyte films (CSEs) with a fiber like structure and local defect channels for rechargeable lithium metal batteries. The CSEs synthesized in situ on LiFePO4 electrode by ultraviolet (UV) curing method, which combines the high ionic conductivity of Li6.5La3Zr1.5Ta0.5O12 (LLZTO) ceramic particles and the flexibility of poly(vinylidene fluoride-co -hexafluoropropylene) (PVDF-HFP) polymer electrolyte. In order to investigate the effect of crosslinker on the performance of electrolytes, 1,6-hexanediol diacrylate (HDDA) and ethoxylated trimethylolpropane triacrylate (ETPTA) were used in the preparation process of ultraviolet (UV) curing method. A comparison was made between gel electrolytes using HDDA and ETPTA crosslinkers, electrolytes containing ETPTA exhibited good overall performance in terms of ion conductivity (7.89 × 10−4 S cm−1), Li+ transference number (0.63), glass transition temperature (−26.2 °C), good flexibility, thermal stability. As a result, the assembled LiFePO4||electrolytes containing ETPTA||Li batteries exhibit excellent the first discharge capacity (151.9 mAh g−1 with 0.1C), good rate performance and its capacity retention rate is 93.1 % after 300 cycles. This study provides a new strategy for the rational design and process method of high-performance CSEs for rechargeable solid lithium metal batteries.

A review of low-temperature lithium metal battery research

Rechargeable lithium metal batteries (LMBs) are one of the promising energy storage systems, which have the advantage of a high theoretical specific capacity of 3860 mAh/g and a low reduction potential of −3.04 V vs. SHE. With the development of society, the large use of batteries in low-temperature areas is inevitable. Typically, batteries fail at low temperatures, especially with temperatures below −20 °C, but the research on low-temperature behavior is limited. According to previous research on low-temperature lithium metal batteries, the main challenge is to suppress serious dendrite growth at low temperatures. Here, we reviewed the state-of-art progress of low-temperature LMBs, including protect layer, three-dimensional collector, and electrolyte. We found that most of the research works relate to electrolytes because a novel electrolyte can easily solvate, contribute to ion transportation, and be conducive to solid electrolyte interfacial (SEI) film formation, which can accelerate the kinetics at low temperatures, thus suppressing the serious dendrite growth at low temperatures. We propose that solid electrolytes can suppress the dendrite growth of LMBs at low temperatures effectively because solid electrolytes are not easy to be pierced.