Rear Side Research Articles

Improving the Efficiency of Semitransparent Perovskite Solar Cell Using Down-Conversion Coating.

Perovskite solar cells (PSCs) have demonstrated exceptional efficiency, yet surpassing theoretical performance limits requires innovative methodologies. Among these, down-conversion techniques are pivotal in reducing optical losses and enhancing energy conversion efficiency. In this study, optical modeling, including a generalized transfer-matrix optical model, was employed to meticulously assess optical losses in semitransparent PSCs illuminated from the front and rear sides of the device. To reduce these losses, two down-conversion layers, made of N,N-diphenyl-4-(1,2,2-triphenylethenyl)-benzenamine and 4-(N,N-diphenylamino)benzaldehyde mixed with polymeric binder, were developed, showcasing initial photoluminescence quantum yields of 60% and 50% as films, respectively. The materials luminescence relies on the effect of aggregation-induced emission, which enhances the fluorescence of the dyes within the binder, providing their films with a unique behavior beneficial for photovoltaic applications. An optimization of these layers was performed, which aimed to reduce UV optical losses by adjusting the film thickness atop the PSCs. The refined down-conversion layers yielded a notable increase in the power conversion efficiency by approximately 0.4% for both the front and rear sides of the PSCs, demonstrating their significant potential in pushing the boundaries of solar cell performance.

Thermal stress in externally irradiated tubes of solar central receivers with a gas–particle fluidized dense suspension

One of the objectives of the new generation of concentrating solar power plants is to increase the actual temperature limit (565 °C) up to or near 1000 °C. An alternative heat transfer fluid that could help to reach this objective is the use of a fluidized dense gas–particle suspension ascending through a vertical tube. Since the predominant cause of rupture in solar receivers is the creep-fatigue damage process, which is mostly influenced by the maximum temperatures and stress experienced along the tube, the main objective of this work is to numerically study the thermomechanical behavior of a non-uniform externally irradiated tube where particles are fluidized and moves upwards. The heat transfer problem in the two media present (i.e. dense suspension of particles and tube wall) was solved separately: a Computational Particles Fluid Dynamic model solves the heat transfer in the particles, whereas a three dimensional Finite Volume model simulates the heat conduction through the tube wall to obtain the temperature profile, which serves as input to calculate the thermal stress of the tube with an analytical method. Higher thermal stresses were obtained for an absorbed power of 250 kW/m2 (σVM,max=219MPa) compared to that for an absorbed power of 500 kW/m2 (σVM,max=72MPa) due to the lower temperature difference between the front and rear sides of the tube caused by the more pronounced increase of the radiative losses in the front side of the tube compared to that at the rear side. The thermomechanical behavior of a particle receiver was compared to that of a molten salt receiver. For an incident solar flux of 500 kW/m2, the particle receiver reduced the maximum thermal stress by 73% compared to the molten salt receiver. However, the tube’s maximum temperature exceeded the working limit for stainless steel tubes. In order for the receiver to survive heat fluxes characteristic of solar power plants, research into technological solutions that allow to improve the effectiveness of the heat transfer rate from the tube to the particle flow is necessary.

Damage features and mechanism of prestressed hollow square piles subjected to non-contact underwater explosion

Critical hydraulic structures are increasingly vulnerable to underwater explosion attacks, with the supporting piles being prime targets for terrorist activities. This study investigates the damage effects and mechanisms of prestressed concrete hollow square (PCHS) piles under non-contact underwater explosions. A series of underwater explosion experiments was conducted on four PCHS piles. The dynamic response of PCHS piles throughout the underwater explosion process was simulated using a coupled fluid-solid numerical model. The mechanisms of dynamic damage to the PCHS piles were elucidated through an integrated analysis of both experimental and numerical results. The research indicates that the damage characteristics of PCHS piles include longitudinal and oblique cracks on the lateral surfaces, transverse cracks on the rear side, and localized fragmentation of concrete. Three primary damage modes have been identified: bending failure(L¯c= 0.59 m/kg1/3), combined bending-shear failure(L¯c= 0.36 m/kg1/3), and punching failure(L¯c= 0.24 m/kg1/3). The local and global responses induced by shock waves are the primary causes of structural damage. Furthermore, as the stand-off distance decreases, the impact of explosive bubbles increases the magnitude of the overall response. A comparative analysis also examined the impact of prestress and axial load on the damage behavior of hollow square piles.

An Ultra‐Thin Dual‐Polarized Bandpass Frequency Selective Surface for 2.45‐/5.8‐GHz ISM Bands

ABSTRACTThis paper presents the design of a single‐layer, double‐sided frequency selective surface (FSS) with bandpass characteristics at the S‐band (2.45 GHz) and C band (5.8 GHz) for sub‐6‐GHz Industrial Scientific and Medical (ISM) bands. The proposed FSS is based on the concept of complementary FSS that produces additional resonant modes. The FSS is constructed using an ultra‐thin microwave laminate with a thickness of 0.00076λeff calculated at the C‐band. The solid patch on the front side of the FSS unit cell is composed of an octagonal ring connected to four spiral arms while the slotted region on the rear side is complementary to the geometry on the front side. The unit cell size of the proposed FSS element is 0.087λeff × 0.087λeff. The FSS has an ultra‐low profile with at least 40% size reduction compared to the state‐of‐the‐art. The FSS element offers 11.12% (288 MHz) and 11.45% (650 MHz) at 2.45 GHz and 5.8 GHz, respectively, at x‐polarization while 5.8% (142 MHz) and 5.9% (342 MHz) bandwidth in the y‐polarization. The FSS element has a rotational symmetric structure offering enhanced polarization stability and angular independent operation for oblique incidences up to 80°. Furthermore, FSS operation is stable, which is evaluated and presented. The prototype bandpass FSS is fabricated, and the simulation results are validated in real‐time using experiments.

Efficient Fog-Harvesting Origami Fan.

Fog harvesting represents a promising strategy to address the global freshwater shortage. To enhance the water collection efficiency, diverse geometric structures that can effectively drive water droplet movement are essential. Inspired by the Livistona chinensis leaf, which naturally facilitates directional droplet motion through its unique gradually varying V-groove structure, we have developed a novel origami fan structure for fog harvesting through theoretical analysis. A key feature is that we can modulate the speed of droplet transport by adjusting the opening angle of the V-shaped grooves positioned at the outer circumference. Interestingly, the water collection efficiency exhibits a linear correlation with the opening angle. The highest efficiency of the origami fan can reach 5.75 times that of the control group calculated by the projected area and 3.76 times that of the control group calculated by the real area, showcasing its significant potential for enhancing water collection from fog. The simulations demonstrate that the hollow structure enhances the condensation rate of droplets, the geometric gradient of the gradual-variation V-groove drives the condensed droplets to move rapidly on the surface, and the Janus membrane permits the aggregated droplets to transit to the fan's rear side. The synergistic action of these three components ensures a clean surface for the subsequent water-collecting cycle, contributing to the high fog-harvesting efficiency. Given its simple fabrication and superior water transfer efficiency, the origami fan holds substantial promise for widespread application in the field of droplet manipulation.

Enhanced pointing and charge properties of electron beams from few-TW laser wakefield acceleration with an asymmetric density profile in a sub-millimeter nitrogen gas jet

This work demonstrates the feasibility of creating a sub-millimeter, subsonic nitrogen gas jet using a 178-μm diameter orifice to conduct laser wakefield acceleration (LWFA) with 1-TW, 40-fs laser pulses. More importantly, our findings reveal that using a blade to impede part of the gas flow and create an asymmetric density profile with a shortened down-ramp leads to a notable reduction in pointing fluctuations and an increase in the total charge of the output electron beams. As evidenced by the corresponding particle-in-cell simulation, the laser intensity is more effectively sustained toward the downstream end of the shaped gas jet, allowing for effective excitation of low-amplitude plasma waves that help preserve the accelerated electrons over the target rear side. In contrast, the pulse intensity drops significantly within the rear side of the unshaped gas jet, resulting in continuously diminishing plasma waves and decreased beam charge. The steeper gradient of the density down-ramp in the shaped gas jet also leads to a more rapid increase in the plasma wavelength over a reduced propagation distance, which helps mitigate the dephasing of accelerated electrons and increase the charge at the high-energy side of the spectrum. Our study paves the way for the future development of few-TW LWFA using a subsonic gas jet with sharp edges to further enhance the properties of output electron beams.

An overview on building-integrated photovoltaics: technological solutions, modeling, and control

The advancement of renewable and sustainable energy generation technologies has been driven by environment-related issues, energy independence, and high costs of fossil fuels. Building-integrated photovoltaic systems have been demonstrated to be a viable technology for the generation of renewable power, with the potential to assist buildings in meeting their energy demands. This work reviews the current status of novel PV technologies, including bifacial solar cells and semi-transparent solar cells. This review discusses the various constructions of PV technologies, recent advances in these products, the influence of key design factors on electrical and thermal performance, and their potential in the design of energy-efficient smart buildings. The attention is focused on bifacial and semi-transparent PV systems, given the high level of interest of the scientific community in their current and potential applications.Focus is also devoted to the analysis of the electrical, optical, and thermal modeling procedures developed for sizing, designing, and integrating photovoltaics into larger building simulations. The development of these models has a positive impact on the implementation of next-generation smart buildings. The latest innovative developments and key issues in the application of bifacial PV solutions in buildings are also summarized and analyzed. Special attention is paid to rear side electrical performance, which can be evaluated by means of illuminance/optical backside modeling. Finally, energy management and control of PV-equipped buildings via both model-based and data-driven approaches are discussed, as well as the integration of electric storage systems in a multi-building context.

Design and test of a module of a breathable Electrostatic Shield for the MITICA 1 MV negative ion Beam Source

The electrical insulation of the MITICA Beam Source at 1 MV is a challenging issue, which has not been fully addressed so far on the basis of experimental results and of theoretical models available in literature. Being MITICA the full-size prototype of the Heating Neutral Beam Injector for the ITER fusion experiment, its electrical insulation is constituted just by vacuum gaps and alumina insulators, since other insulating materials such as SF6 gas or fibreglass-reinforced plastic (FRP) would be quickly degraded by the expected neutron flux produced by fusion reaction. Extrapolations based on HV tests on reduced-scale models have recently indicated the risk of electrical breakdowns in the vacuum gap between electrodes nominally operating at -1 MV and the vacuum vessel (at ground potential). The risk of electrical breakdown can be mitigated by introducing an intermediate Electrostatic Shield (ES), which essentially is an equipotential (metallic) enclosure surrounding the HV electrode, so as to divide the vacuum gap in two independent insulating gaps of 400 kV and 600 kV respectively. However, for optimal negative ion production, the ion source shall operate in H2 or D2 at a pressure of ∼ 0.3 Pa and unavoidably produces a flow of gas leaking out in the surrounding vacuum. Thus, the presence of an intermediate shield can substantially increase the background gas pressure in the vacuum gaps, and, due to the large gap length (0.6 m), exacerbate the risk of breakdown when the pressure approaches the conditions of Paschen-type discharges. In addition to this, RF-induced breakdowns were found on the rear side of the ion source during the operation of the prototype source SPIDER, which were somewhat correlated to a relatively high hydrogen pressure in that area. For these reasons, a structure capable of constituting a full equipotential barrier all around the BS and, at the same time, having sufficient gas conductivity (breathability) to allow efficient pumping of background gas, has been designed. In the first part of the paper, the requirements and design optimization of a breathable module of the intermediate ES are described. Then, an experimental campaign for the validation of the electrode implementation the test configurations and the experimental procedure is discussed.

Unveiling the origin of metal contact failures in TOPCon solar cells through accelerated damp-heat testing

Tunnel oxide passivated contact (TOPCon) solar cells are expected to dominate the global photovoltaic market in the coming decade thanks to rapid advancements in power conversion efficiency (PCE). However, there are concerns about the reliability of TOPCon modules, particularly in hot and humid conditions. The current module-level fundamental analysis strategies for TOPCon solar cells provide too slow feedback for rapid process development. This study explores the degradation of metal contacts in TOPCon solar cells under accelerated testing conditions of 85 °C and 85 % relative humidity (DH85). The degradation was induced by two commonly used sodium-related salts, sodium bicarbonate (NaHCO3) and sodium chloride (NaCl), in the testing of the solar cells. When applied to the front side, NaHCO3 caused a ∼5%relPCE reduction after 100-h DH85 exposure, while NaCl leads to a more significant ∼92%relPCE reduction. The primary cause of degradation is a considerable increase in series resistance (Rs), likely due to electrochemical reactions within the Ag/Al paste. When the salts are applied to the rear of the TOPCon solar cell, the degradation becomes more complex. NaHCO3 increases recombination and results in a deterioration of the contact, resulting in a ∼16%relPCE reduction after 100-h DH85 testing. Conversely, NaCl primarily causes a decline in open-circuit voltage (Voc) and a ∼4%relPCE loss. This manuscript primarily investigates degradation mechanisms related on the rear side, with a focus on significant oxidation occurring at the interface between Ag and Si. These findings highlight the susceptibility of TOPCon solar cells to contact corrosion, emphasizing the electrochemical reactivity of metallisation as a potential risk for long-term TOPCon module operation. This study provides crucial insights into TOPCon cell degradation mechanisms, which are essential for optimising performance and enhancing the long-term reliability of TOPCon modules.

View Factors Approach for Bifacial Photovoltaic Array Modeling: Bifacial Gain Sensitivity Analysis

Abstract Bifacial modules are highly valued in the global photovoltaic market since they are able to receive sunlight from both sides and can generate up to 10–30% additional energy compared to monofacial ones. They are integrated into various sectors, including building and notably Agrivoltaics. In this work, a coupled optical–thermal–electrical model was developed in matlab to simulate the energy performance and bifacial gain for a ground-raised bifacial system. The model allows optimization as a function of the photovoltaic (PV) system and bifacial module characteristics. A fixed, south-facing bifacial PV arrays composed of three rows assumed installed in Agadir, Morocco, is considered. The optical model is based on an analytical determination of view factors using the cross-string rule. These enable the determination of irradiances received by both sides of modules, which are subsequently used to evaluate energy yield of the system. Model validation was carried out based on various statistical metrics by comparing our results with simulation results generated by various softwares. The comparison shows a very good agreement, notably with 3dbifacialvf (R2 = 1, root-mean-square error (RMSE) = 0.03 W/m2 and R2 = 0.96, RMSE = 12.4 W/m2) for front and rear side irradiance, respectively. The DC energy generated by the system differs by less than 1% compared to pvsyst results. Sensitivity analysis revealed that all system parameters, particularly ground albedo, positively affect the bifacial gain. The bifacial gain increased from 10.6% to 20.1% as the ground albedo increased from 0.25 to 0.5.

Plasmonic effect of gold nanoparticles on rear side of flexible black silicon wafer fabricated by aluminum-assisted chemical etching

In this work, we investigate the effects of the different sizes of gold (Au) plasmonic nanoparticles (NPs) on the rear surface of flexible black silicon (b-Si) wafer. The flexible b-Si (65 μm thickness) is fabricated by aluminum-assisted chemical etching (AACE) process, utilizing aluminum (Al) as the catalyst. After the b-Si fabrication, nanopores are produced on the flexible wafer surface. Then, gold nanoparticles (Au NPs) are spin-coated on the rear side of the flexible b-Si, followed by surface morphological and optical characterizations. The Au NPs with sizes of 24–92 nm have been deposited on the rear surface of the b-Si wafer. Based on the optical characterization, light absorbance increases above wavelength 800 nm due to enhanced light scattering by the Au NPs at the back surface. The average reflectance (Rave) is calculated in the 300 nm–1100 nm wavelength range for flexible crystalline silicon (c-Si) reference and compared with flexible b-Si surface and flexible b-Si/Au NPs. The lowest Rave of 15.4% is achieved for Au NPs with average size of 92 nm.

Outdoor Performance Analysis of Semitransparent Photovoltaic Windows with Bifacial Cells and Integrated Blinds

The stricter requirements for the energy performance of buildings are creating a market for several building‐integrated photovoltaic (BIPV) technologies, including photovoltaic (PV) windows. Herein, an innovative multifunctional PV window concept designed to enhance energy generation while providing overheating protection for better indoor thermal and visual comfort is presented. This concept utilizes bifacial c‐Si solar cell strips combined with venetian blinds, all embedded in a unique insulating glazing unit. The bifacial technology increases the energy yield by using the blinds as reflectors, directing more irradiance to the cells’ rear side. The goal of this study is to analyze the outdoor performance of this concept under real operating conditions. Twelve demonstrators are installed and monitored. Various measurement campaigns are conducted, examining the impact of different blind types, tilt angles, sun positions and sky conditions. The highest energy boosts occur when the blinds are fully closed at a 75° angle with their convex side facing outward. Blinds with the highest specular reflectance achieve a maximum performance increase of 25% on sunny days and a daily average increase of 12% compared to the case of no blinds.

Direct visualization of viscous dissipation and wetting ridge geometry on lubricant-infused surfaces

Drops are exceptionally mobile on lubricant-infused surfaces, yet they exhibit fundamentally different dynamics than on traditional superhydrophobic surfaces due to the formation of a wetting ridge around the drop. Despite the importance of the wetting ridge in controlling drop motion, it is unclear how it dissipates energy and changes shape during motion. Here, we use lattice Boltzmann simulations and confocal microscopy to image how the wetting ridge evolves with speed, and construct heatmaps to visualize where energy is dissipated on flat and rough lubricated surfaces. As speed increases, the wetting ridge height decreases according to a power law, and an asymmetry develops between the front and rear sides. Most of the dissipation in the lubricant ( >75%) occurs directly in front and behind the drop. The geometry of the underlying solid surface hardly affects the dissipation mechanism, implying that future designs should focus on optimizing the surface geometry to maximize lubricant retention.

Distinguishing the vertical air-staging low-NOx function of secondary air for suspension combustion within an industrial-scale coal-fired reversal grate furnace

The numerous coal-fired grate furnaces in China, which were designed to partition primary air on the grate and arrange secondary air in the freeboard for air-staging combustion, suffered from poor burnout and high NOx. However, secondary air was conventionally closed or set at marginal openings in real operations and no investigation was reported to explain why. Upon these off-design secondary-air circumstances, industrial-scale tests and modeling investigations were performed for a 75 t/h coal-fired reversal grate furnace at secondary-air ratios of 0 %, 3 %, 6 %, 10 %, and 16 %, respectively. The primary aims were to (i) uncover its combustion and NOx formation characteristics with varying secondary air and (ii) confirm whether secondary air acted on a real air-staging function in reducing NOx. Flow-field deflection and asymmetric combustion were found in the furnace, with the upward gas entirely deflecting towards the rear side. The front-half furnace was filled with a large but weak recirculation zone without effective combustion, acting on a huge dead zone to waste the furnace-space utilization. With increasing the secondary-air ratio, the upward gas deflection deteriorated continuously. Layer combustion worsened while suspension combustion first strengthened and then weakened. NOx emissions displayed an ascent-to-descent trend. Carbon in slag raised while carbon in fly ash decreased. Among the five case setups, the 0 % setting (i.e., fully closing secondary air) exhibited the lowest NOx emissions and burnout loss. Compared with the habitual 6 % setup, fully closing secondary air not only reduced NOx emissions by 22 % but also improved a little burnout. These trends meant that opening secondary air only strengthened suspension combustion for burning well fly ash while raised both NOx and total burnout loss. Secondary air thus failed to role as an air-staging function in reducing NOx.

Regulation of cholesterol biosynthesis by CTCF and H3K27 methylation is critical for cell migration

CTCF is a key factor in three-dimensional chromatin folding and transcriptional control that was found to affect cancer cell migration by a mechanism that is still poorly understood. To identify this mechanism, we used mouse melanoma cells with a partial loss of function (pLoF) of CTCF. We found that CTCF pLoF inhibits cell migration rate while leading to an increase in the expression of multiple enzymes in the cholesterol biosynthesis pathway along with an elevation in the cellular cholesterol level. In agreement with the cholesterol change we detected altered membrane dynamics in CTCF pLoF cells as measured by reduced formation of migrasomes, extracellular vesicles formed at the rear side of migrating cells. Inhibition of cholesterol synthesis in CTCF pLoF cells restored the cellular migration rate and migrasome formation, suggesting that CTCF supports cell migration by suppressing cholesterol synthesis. Detailed analysis of the promoter of Hmgcs1, an early enzyme in the cholesterol synthesis pathway, revealed that CTCF prevents formation of a loop between that promoter and another promoter 200 kb away. CTCF also supports PRC2 recruitment to the promoter and deposition of H3K27me3. H3K27me3 at the promoter of Hmgcs1 prevents SREBP2 binding and activation of transcription. By this mechanism, CTCF fine-tunes cholesterol levels to support cell migration. Notably, genome wide association studies suggest a link between CTCF and cholesterol-associated diseases, thus CTCF emerges as a new regulator of cholesterol biosynthesis.

22.56% total area efficiency of n-TOPCon solar cell with screen-printed Al paste

Screen-printing Ag paste on the rear side of the Tunnel Oxide Passivated Contact solar cells (TOPCon) is still the mainstream method to form electrodes. However, the high price of precious metals increases the cost of TOPCon cells. Al is a cheap and high-performance conductor, and its work function is compatible with the rear side of TOPCon cells. In this study, we used a UV pulse laser (355 nm, 10 ps) to ablate the rear side SiNx passivation layer of TOPCon cells and then printed Al paste with different weight percentages of silicon (Si-wt.%) on the phosphorus-doped polycrystalline silicon (n+-poly-Si) layer to reduce the cost. We investigated the damage mechanism of laser on SiOx/n+-poly-Si/SiNx passivation structure and the contact mechanism between Al paste and n+-poly-Si layer. The results show that the Voc of SiOx/n+-poly-Si/SiNx passivation structure reduced about 6–7 mV when the laser energy density was 0.431 J/cm2. We got the best electrical performance of TOPCon cells printed with Al paste (25 wt%-29 wt% silicon). The open-circuit voltage (Voc) and the conversion efficiency (Eff), have reached 663.60 mV and 22.56 % respectively. Although the efficiency was 9.40 % relative lower than that of TOPCon cells printed with Ag paste, but the cost of Al paste only accounted for 10 % of Ag paste. In the future, the highest Eff of TOPCon solar cells printed with Al paste on the rear side are expected to reach the commercial TOPCon based on Ag paste, which applies laser doping selective emitter technology (SE) and bifacial poly-Si passivation structure.

First report of Fusarium luffae causing soybean wilt in the USA.

During the 2023 soybean growing season in South Dakota, we scouted a farmer's field and observed soybean (Glycine max (L.) Merr.) plants with wilting symptoms and blighted leaves. Symptomatic stems and leaves were collected from the field to identify associated pathogens. 0.5 cm2 size leaf and stem segments of the sample were surface sterilized by rinsing with 10% bleach for 5 minutes then dipping in 70% ethanol for one minute, and later placing in deionized sterile water for one minute. The sterilized segments were placed on wet filter paper and incubated under fluorescent light for three days. Fungal growth was observed, and the growing mycelia were transferred to potato dextrose agar plates amended with 50 µg/ml Ampicillin (PDAa). Pure culture of the isolate was obtained using single sporing and transferring on new PDAa plates. A dense aerial mycelial growth showing waxy yellow color with a pale orange tinge on the rear side covered the full plate after seven days of incubation at room temperature under fluorescent lights (Figure S1a and b). Developing macroconidia were falcate, curved, smooth to slightly rough, and hyaline with three-five septa (Figure S1c). For molecular identification, DNA of the recovered isolate was extracted and subjected to multiloci PCR (O'Donnell et al., 2010) to amplify and Sanger sequence the internal transcribed spacers region (ITS) (GenBank accession number PP393518), calmodulin (CAM-PP401978), RNA polymerase II second largest subunit (RPB2-PP401980), and translation elongation factor 1-α gene (TEF1-PP401979). The South Dakota isolate (SLSDF2) was identified as Fusairum luffae on NCBI and Fusarioid polyphasic identification databases with 99.40% similarity to Fusarium luffae strain NRRL31167. A phylogeny was inferred based on concatenated TEF1, RPB2, and CAM sequences to show species relatedness (Figure S3). The characterized isolate SDSLF2 was evaluated for soybean pathogenicity using spray inoculations on detached leaves and V2 stage soybean plants (Figure S2a and b). The conidial suspension was prepared by growing the pathogen on mung bean agar for seven days. 2 ml of conidial suspensions (2.6 × 104 conidia/ml) and mock control (sterilized water with 0.1% Tween-20) was sprayed on the detached leaves and whole plants. The experiment was repeated three times with four replicates in each. In the detached leaf assay, leaves were completely blighted (Figure S2a) within 96 hours. In whole plant assays, after two days of incubation, leaf blighting was visible and progressed with time. Four days post-inoculation, the infected plants showed extensive leaf symptoms, and ultimately defoliation occurred (Figure S2b). No symptoms were observed in mock controls of either of the experiments. The pathogen was reisolated from the infected tissues and its identity was confirmed as F. luffae by CAM sequencing fulfilling Koch's postulates. F. luffae has been reported to associated with soybeans in China (Zhao et al., 2022), however, to our knowledge, this is the first report of F. luffae pathogenic on soybeans in the USA, stressing the need to identify resistance sources to avoid any potential disease epidemic.

Hydrodynamic analysis of sea-crossing bridge piers subjected to freak waves

Coastal areas are witnessing a surge in critical infrastructure development, such as sea-crossing bridges, to support growing populations and economic activities. However, these structures face ongoing challenges in harsh marine environments. Therefore, understanding the hydrodynamics of bridge structures under extreme freak wave conditions is imperative for designing effective countermeasures. This study investigates pier hydrodynamics using a three-dimensional numerical flume simulated by OpenFOAM, focusing on loading characteristics and wave climb differences under freak and linear waves. Results show that freak waves induce larger surges and forces compared to linear waves, with a notable “bell vibration” effect near the wave surface. Moreover, peak forces and bending moments increase nonlinearly with the wave height-to-significant wave height ratio. For double-column piers, transverse alignment concentrates wave climb on the rear side of the front pier, with forces increasing with spacing, while those on the rear pier decrease. Conversely, longitudinal arrangements show amplified loading effects. These findings provide valuable insights into the hydrodynamic behaviour of bridge piers under freak wave conditions, offering practical implications for the design and protection of sea-crossing bridges.

PSPMoni: A Robust Wear Monitoring Method of Pantograph Slide Plate

The pantograph slide plate (PSP) plays a crucial role in the daily maintenance of trains by transmitting electrical energy from the contact wire (CW) to the train. Automatic monitoring of PSP wear condition is essential to notice abnormal wear promptly. In field applications, the target PSP edge may be obscured by the rear side PSP due to the operating attitude of the pantograph, leading to false detections and interfering with the field maintenance work. Meanwhile, the scenario of the PSP occlusion is characterized by randomness, which brings a considerable challenge to the reconstruction of the occluded edges. A robust PSP wear monitoring method is proposed to improve the performance of wear detection in field applications, considering the PSP occlusion scenarios. Firstly, the wear area of the PSP is localized using the YOLOv5s model. Subsequently, a fusion of the morphology method and the Canny operator is employed to extract the edge of the PSP. Different occlusion types are identified through detailed observation, and corresponding edge reconstruction methods are proposed for occluded edges. Finally, a robust wear condition evaluation method and five evaluation criteria for assessing wear condition are introduced. Experimental results demonstrate that the system achieves accurate PSP wear detection with an accuracy of 0.6 mm, and the reconstructed edge at occlusion locations closely matches the target edge compared to other automatic systems.

All-back-contact neutral-colored transparent crystalline silicon solar cells enabling seamless modularization

Transparent solar cells (TSCs) hold substantial potential as continuous energy generators, enabling their use in situations where conventional devices may not be feasible. However, research aimed at modularizing TSCs for the purpose of regulating the overall voltage and current they produce, a critical step toward practical application, is still in its nascent stages. In this study, we explored a custom-designed, all-back-contact (ABC) configuration, which situates all electrical contacts on the rear side, to create glass-like transparent crystalline silicon (c-Si) solar cells and seamless modules. The ABC design not only demonstrates high power conversion efficiency (PCE) in solar cells but also ensures unobstructed visibility through transparent solar modules. Notably, ABC-transparent c-Si solar cells achieved a peak PCE of 15.8% while maintaining an average visible transmittance of 20%. Through seamlessly interconnecting the unit cells, the output voltage and power were systematically tuned from 0.64 V and 15.8 mW (for a 1 cm2-sized unit cell) to 10.0 V and 235 mW (for a 16 cm2-sized module). Furthermore, we successfully demonstrated the photocharging of a smartphone using a transparent ABC solar module.