Deposition Rate Research Articles

Epitaxial RuO2 and IrO2 films by pulsed laser deposition on TiO2(110)

We present a systematic growth study of epitaxial RuO2(110) and IrO2(110) on TiO2(110) substrates by pulsed laser deposition. We describe the main challenges encountered in the growth process, such as a deteriorating material flux due to laser-induced target metallization or the delicate balance of under- vs over-oxidation of the “stubborn” Ru and Ir metals. We identify growth temperatures and oxygen partial pressures of 700 K, 1 × 10−3 mbar for RuO2 and 770 K, 5 × 10−4 mbar for IrO2 to optimally balance between metal oxidation and particle mobility during nucleation. In contrast to IrO2, RuO2 exhibits layer-by-layer growth up to 5 unit cells if grown at high deposition rates. At low deposition rates, the large lattice mismatch between film and substrate fosters initial 3D island growth and cluster formation. In analogy to reports for RuO2 based on physical vapor deposition [He et al., J. Phys. Chem. C 119, 2692 (2015)], we find these islands to eventually merge and grow to continue in a step flow mode, resulting in highly crystalline, flat, stoichiometric films of RuO2(110) (up to 30 nm thickness) and IrO2(110) (up to 13 nm thickness) with well-defined line defects.

Enhancement of copper nanoparticle yield in magnetron sputter inert gas condensation by applying substrate bias voltage and its influence on thin film morphology

Large-scale synthesis of high-purity nanoparticles is an intense topic of scientific research, with magnetron sputter inert gas condensation recognized as a promising, environmentally friendly technique avoiding wet chemical processes. This study explores the deposition of size-selected nanoparticles under varied substrate bias voltages and reports on a consequent increase in deposition rates up to 32 %. These alterations in substrate bias voltage induce a progressive change in the morphology of the resulting nanoparticle thin films, attributable to the increased kinetic energy of the nanoparticles. Comprehensive characterization via quadrupole mass spectroscopy of the nanoparticle flux, scanning electron microscopy, X-ray photoelectron spectroscopy, and low-energy ion scattering spectroscopy of the deposited nanoparticles corroborates the enhanced nanoparticle yield associated with increased substrate bias voltage. These findings signify a methodological advancement, enhancing the efficiency of magnetron sputter inert gas condensation and moving the technology a step further towards feasible industrial production.

Phase composition of sputter deposited tungsten thin films

Sputter deposited tungsten thin films are studied by X-ray diffraction. Two phases can be identified: α-W and β-W based on the observed (110), and (200) and (210) Bragg reflections, respectively. With increasing film thickness (50 to 200 nm), the phase composition shifts from β-W towards α-W. No influence of the base pressure (3 × 10−3 – 3 × 10−5 Pa) on the phase composition is observed. Also the influence of the argon pressure (0.3 to 0.7 Pa) is rather weak. The strongest shift towards α-W composed thin films is obtained by increasing the discharge power (50 to 250 W). This trend is further studied by energy flux measurements using a calorimetric probe. These measurements rule out a strong change of the substrate temperature, and an impact of the energy flux scaled by the deposition rate (total energy per deposited atom). Test particle Monte Carlo simulations reveal the importance of the momentum of the reflected argon neutrals on the phase composition. The maximum energy of these species is mainly defined by the discharge voltage, and is higher than the directional dependent displacement energy of W. Despite the significant correlation between phase composition and the number of displacement per deposited atom, there is a strong scatter of the phase composition. As the deposition conditions were varied in random way, changes of the target erosion profile, and the changing discharge voltage over each series are probably partially responsible for the observed scatter. This scatter is also enhanced by the long term changes in the phase composition towards the more thermodynamic stable α-W phase.

Seasonal variation of particle number concentration in a busy urban street with exposure assessment and deposition in human respiratory tract

Ultrafine particles (UFP) associated with air quality and health impacts are a major concern in growing urban regions. Concentrations of UFP (particles of size between 10 and 100 nm) and accumulation mode (Nacc) (particles of size >100 and up to 1000 nm), are analyzed over a highly polluted megacity, Delhi, in conjunction with vehicular flow density, during peak (morning, and evening) and non-peak hours. UFP contributes ≥60% to total particle concentration during autumn and monsoon. UFP concentrations are about 50,000 particles per cm3 in winter which reduces to about 25,000 particles during monsoon. Nacc are about 20,000 (winter) and 10,000 (monsoon) particles per cm3. UFP concentration and Nacc during peak hours are at least twice higher than those obtained in non-peak hours, confirming the dominant influence of emissions from vehicular exhaust in the study region. Seasonal analysis of UFP size distribution reveals that direct emissions dominate the particle concentrations during winter and autumn, whereas new particle formation mechanism contributes the highest in spring and summer. Assessment of inhalable particle number concentration and particle deposition in the human respiratory tract using Multiple Path Particle Dosimetry (MPPD) model, performed for the first time, shows that the order in which these particles deposit in the human respiratory tract is alveoli > bronchiole > bronchus. The deposition ranges between 10 and 18 million nanoparticles during different hours of the day, whereas the estimated inhalable particle concentration (IPN) varies between 0.5 and 1 billion. Results on the IPN during activities classified from light (walking), medium, heavy, very heavy to severe (long-distance running) provide insights into health effects on vulnerable populations. These quantitative results obtained over a megacity on hourly and seasonal variations of nanoparticles along with IPN and deposition rates for different activities are important, and are invaluable inputs for developing mitigation policies aimed to improve air quality and public health, both of which are major concerns in South Asia.

Effect of TaC content on microstructure and wear behavior of PRMMC Fe-TaC coating manufactured by electrospark deposition on AISI304 stainless steel

The Fe-TaC coatings on stainless steel by electrospark granule deposition in an anode mixture of iron granules and tantalum carbide powder were first obtained. The material deposition rate on the substrate increased with the TaC powder concentration growth in the anode mixture, facilitating the initiation of electrical discharges. X-ray analysis of deposited coatings shows the presence of the TaC, γFe, and αFe phases. The tantalum carbide concentration grows with an increase in the content of TaC powder in the anode mixture, from 2.4 to 14.8 vol%. The dependence of the wear rate of coatings on the concentration of tantalum carbide in the anode mixture had a parabola form, with a minimum of 5 vol%. However, with a further increase in the TaC concentration in the anode mixture, the wear rate of the coatings monotonically increased due to spalling of TaC grains due to a deficiency of the metal binder.

Atmospheric microplastic input into wetlands: Spatiotemporal patterns, drivers, and unique ecological impacts

Wetlands are major microplastic sinks with a large atmospheric input. However, many details of such deposited atmospheric microplastics entering into wetlands remain unclear, including temporal patterns of input and ecological effects. We monitored the aerial microplastics during four seasons in eleven economically developed cities along the lower reaches of the Yangtze River Basin, China. The average microplastic deposition rate was 512.31 items m−2 d−1, equivalent to an annual contribution of 17.46 metric tons of plastic to the surveyed wetlands with a total area of 1652 km2. These microplastics were predominantly composed of polyamide and polyethylene terephthalate with 61.85 ± 92.29 µm sized pellets, and we obtained similar results for microplastics intercepted on moss in wetlands. Microplastic input varied between wet and dry periods, primarily influenced by wind, rainfall and ozone concentration. Civilian vehicle density and textile industry were the primary socioeconomic factors driving microplastic deposition. Further indoor microcosm experiments revealed that moss phyllosphere bacterial community structure and function were influenced by microplastic abundance and size, exemplifying the unique ecological risks of aerially deposited microplastics to wetlands. These results indicate that mosses and their phyllosphere microbiota could serve as bio-indicators of aerial microplastic characteristics and impacts.

Low-loss and low-temperature Al2O3 thin films for integrated photonics and optical coatings

Amorphous aluminum oxide (Al2O3) is a key material in optical coatings due to its notable properties, including a broad transparency window (ultraviolet to mid-infrared) and excellent durability. Moreover, its higher refractive index contrast relative to silica cladding layers and high solubility of rare-earth ions make it well suited for optical waveguides and the development of various functionalities in integrated photonics. In many coatings and integrated photonics applications, the substrates are temperature and stress sensitive, while relatively thick (∼1 μm) alumina layers are required; thus, it is crucial to fabricate low optical loss alumina thin films at low deposition temperatures, while maintaining high deposition rates. In this study, plasma-assisted reactive magnetron sputtering, operated in an alternating current mode, is investigated as a reliable, straightforward, and wafer-scale compatible technique for the deposition of high optical quality and uniform Al2O3 thin films at low temperature. One-micrometer-thick amorphous Al2O3 planar waveguides, deposited at 150 °C and a rate of 23.3 nm/min, exhibit optical losses below 1 dB/cm at 638 nm and as low as 0.1 dB/cm in the conventional optical communication band.

Influence of localized sources and meteorological conditions on dry-deposited particles: A case study of Gabès, Tunisia

This study investigates the spatial and temporal variations of dry-deposited particles on the surface (by turbulence or gravity) in various sites within Gabès city and its surroundings, South-eastern Tunisia. Monthly samples were collected from five distinct locations: suburban-industrial (S2), suburban-residential (S3), and urban sites (S1, S4, and S5). The average monthly particle deposition flows ranged from 7.35 ± 4.24 g/m2 to 14.41 ± 6.09 g/m2, with the suburban-industrial site (S2) exhibiting the highest deposition rates. They are lower than the reference value of 30 g/m2 in the AFNOR NF-X43-007, but much higher than the Swiss OPair standard (6 g/m2). Compared to the German standard (TALUFT; 10.5 g/m2), only S2 showed significant exceedances. Hierarchical cluster analysis revealed notable statistical affinities among the study sites. Heavy metal analysis indicated fluctuating concentrations across sites, with Zn being the most abundant, followed by Pb, Cu, Ni, and Cd. The enrichment factor (EF) and geoaccumulation index (Igeo) suggested varying degrees of contamination and pollution, highlighting the impact of anthropogenic sources. The findings underscore the need for targeted mitigation strategies to address particle deposition and heavy metal contamination in Gabès and similar regions globally.

Improved wear and corrosion resistance of additively manufactured SS316L by laser remelting process

Directed energy deposition is an efficient and flexible additive manufacturing technique that has broad application prospects due to its ability to fabricate intricate structures with heterogeneous properties. In this study, the laser-based directed energy deposition (L-DED) technique is employed to deposit an austenitic stainless steel 316L powder at a significantly high deposition rate. In recent developments, laser remelting (LR) has been explored as a superior alternative for enhancing the surface integrity of the components produced by L-DED. This study endeavours to examine the impacts of LR, emphasizing the improvement of wear and corrosion resistance. The grain refinement is achieved through laser remelting, which eventually leads to a 34 % improvement in micro–hardness over the as-deposited sample; as a result of increased micro–hardness, wear resistance improved by 66 % when compared to the as-deposited specimen. Furthermore, the corrosion resistance performance of the laser-remelted samples is compared with as-deposited samples by electrochemical impedance spectroscopy (EIS) in a solution of 3.5 % NaCl solution. The remelted sample showed improved corrosion resistance, which is attributed to the grain refinement due to rapid solidification in LR. This study demonstrates that laser remelting can be an effective way to improve the wear and corrosion resistance of SS316L, which enlarges its application in harsh environments.

Low‐Cycle Fatigue Performance of Directed Energy Deposited and Conventionally Manufactured Hybrid Gas Tungsten Arc‐Welded Duplex Stainless Steel Joints

Arc‐directed energy deposition (DED‐Arc) is a technology for the production of complex and large‐scaled components. It benefits from high deposition rates and low investment costs. However, to further expand the applications of additively manufactured parts, the possibility for implementation in conventionally manufactured assemblies is crucial. Therefore, this study focusses on the structural integrity of welded joints of DED‐Arc and as‐rolled duplex stainless steels and the welded and nonwelded as‐rolled benchmark. While the fraction of the constituents is almost balanced in the as‐rolled condition, the amount of austenite in the DED‐Arc specimens exceeds 60%. The similar weldment is predominantly ferritic and the hybrid welded joint contains ≈30% austenite, which is discussed based on the nickel concentration. Results from microstructure characterization are correlated to the superior yield and ultimate tensile strength of the as‐rolled condition. Under total strain‐controlled fatigue experiments, the hybrid welded joints exhibit enhanced fatigue lives at various strain amplitudes while the base material shows lowest fatigue resistance. Computed tomography and fractography conclude that the structural integrity is not governed by inherent defects, but instead the phase ratio and distribution yield significant differences in the cyclic deformation response as well as an asymmetry of the hysteretic stress–strain behavior.

Sub‐Milankovitch Signals in the Northern Polar Layered Deposits of Mars

AbstractOur understanding of the paleoclimate of Mars and the dominant forcing functions that drive large‐scale changes largely remains a mystery. However, the Martian Polar Layered Deposits (PLD) offer a promising avenue for unraveling the planet's recent paleoclimate history. Despite recent progress to detect a climate signal in the PLD, definitive evidence of a correlation between the stratigraphic record and Mars' recent orbital history remains elusive. We utilized new and updated techniques, including high‐resolution stratigraphic reconstruction from High Resolution Imagine Science Experiment stereo imagery and digital terrain models, combined with a technique of variable dip correction to account for three dimensional bedding orientations. Signal processing methods, such as wavelet and Fourier analysis, were applied to perform detailed time‐series analysis. These analyses revealed a quasi‐periodic signal indicative of fine bedding at a scale of approximately 2 m. Based on previously proposed deposition rates, these fine layers appear to correspond to timescales centering around 4,000 years. This suggests that the meter‐scale layers may not be the result of orbital forcing and hint at an unknown sub‐Milankovitch climate forcing mechanism. We discuss potential exogenic causal mechanisms, such as cyclic variations in solar activity, and endogenic factors, including large‐scale changes in dust distribution. Understanding the formation processes of these fine layers may significantly enhance our knowledge of Martian climate history and its driving forces.

Legacy of aerosol radiative effect predominates daytime dust loading evolution

Dust radiative effect imposes pronounced perturbations on planetary boundary layer (PBL) development. In turn, the modified PBL characteristics and circulation fields regulate subsequent dust processes, which have not been explored sufficiently. In this study, parallel experiments are designed to isolate the instant, legacy and nonlinear impacts of aerosol radiative effect on daytime dust storm evolution over the Tarim Basin. During a typical dust storm event, legacy radiative effect is found to dominate dust loading dynamics and modulates mean dust burden by more than 16 % in the central basin and − 41 % in the marginal basin. Specifically, the dust column concentration increases in central regions but decreases in marginal regions. Dust aerosols cause opposite heating rate distributions and PBL structure between the central and marginal regions through altering radiative balance. Dust-induced cooling effect in the marginal regions leads to PBL suppression and attenuates entrainment mixing. Negative net heating also results in lowered potential temperature, elevated air pressure and thus increases their horizontal gradients. Accordingly, wind speeds are amplified through geostrophic and thermal wind effects, which further accelerate deposition rates, and eventually weaken dust suspension. In the central basin, dust plumes stimulate a warm mixing layer and unstable entrainment zone, which inhibit dry deposition removal and favor dust accumulation in the atmosphere. Our study highlights the importance of accounting PBL dynamics and geostrophic balance in quantifying the impacts of preceding radiative effect on subsequent dust evolution.

Comparison of Hardness by Electrolytic and Electroless Deposition of Nickel on Aluminium

Abstract The work deals with the hardness characteristic of substrates coated with nickel through two primary methods: electrolytic deposition and electroless Ni-P deposition. The optimised process parameters for both the process was determined by varying a particular parameter keeping the rest constant in order to obtain minimum crystallite size of Ni. The size of the crystallite were determined using Scherrer’s equation. The optimized combination of process parameter for electrolytic deposition is: 270gm/lt of Nickel Sulfate, 60gm/lt Nickel Chloride, 35gm/lt Boric Acid, current density of 90mA/cm2 bath temperature of 55°C. The optimized combination of process parameter for electroless Ni-P deposition: 34gm/lt Nickel Sulfate, 23 gm/lt Sodium Hypophosphite, 46 gm/lt of Lactic acid, 42 gm/lt of Sodium Citrate, pH 5.0 and bath temperature 85°C. The optimised deposition rate 22μm/hr. Micro-hardness (Vickers) tests were conducted on the coated samples with a 50 gf load. The cause for difference in hardness was due to buildup of residual stress during deposition of Nickel on the substrate(aluminium). The orientation and surface texture of the materials are determined.

Proximity to inlet channel drives spatial variation in sediment carbon across a lagoonal seagrass meadow

Seagrass meadows can be sinks for organic carbon, but estimates of global organic carbon stocks are complicated by substantial spatial variability in organic carbon burial observed within meadows. To improve estimates of organic carbon burial in seagrass meadows, it is necessary to understand the causes of the spatial heterogeneity. This study investigated relationships between spatial patterns in sediment organic carbon storage and accretion rates, hydrodynamics, and proximity to sources of organic carbon in a current-dominated Zostera marina Linnaeus meadow in Menemsha Pond, Massachusetts, USA. Sediment and velocity measurements were conducted at six stations along a 150-m transect across the meadow oriented perpendicular to the pond's unvegetated inlet channel. The meadow's edge near the channel had higher organic carbon than the channel as well as the highest organic carbon within the meadow. With increasing distance from the meadow's edge, all of the following decreased: sediment organic and total carbon, sediment accretion rates, peak tidal velocity, sediment trap mass deposition rate, and the relative contribution of non-seagrass sources to sediment organic carbon. Lower tidal velocities farther from the inlet channel reduced sediment resuspension, consistent with lower sediment trap mass deposition, which should enhance organic carbon content and organic carbon accretion rates. However, the opposite trend of decreasing organic carbon content (>50 % across the transect) and decreasing accretion rates with distance from channel was observed. This suggested that the local hydrodynamic intensity was not controlling organic carbon accretion, which was instead constrained by supply limitation and controlled by the lagoon-scale flow circulation.

Deciphering the microstructural development and excellent ductility in electron beam wire-fed additive manufacturing of Ti-6Al-3Nb-2Zr-1Mo alloys based on high deposition rate

Deciphering the microstructural development and excellent ductility in electron beam wire-fed additive manufacturing of Ti-6Al-3Nb-2Zr-1Mo alloys based on high deposition rate

Mechanical and Metallurgical Characteristics of Wire-Arc Additive Manufactured HSLA Steel Component Using Cold Metal Transfer Technique

Recently, the application of wire-arc additive manufacturing (WAAM) for the production of metallic products is gaining traction. WAAM is associated with the direct energy deposition technique and therefore has a higher deposition rate (approximately 4 kg/h). For this reason, it is of greater interest than powder-based additive manufacturing techniques. Industrial applications such as marine and offshore structures and pressure vessels for space programs commonly utilize high-strength low-alloy (HSLA) steel. HSLA steel components produced by casting methods exhibit defects due to oxidation. Therefore, cold metal transfer (CMT)-WAAM was adopted in this study to fabricate HSLA steel components. The metallurgical properties were analyzed using microscopic and diffraction techniques. The effects of the evolved microstructures on mechanical properties, such as strength, microhardness, and elongation to fracture, were evaluated. To analyze and test the structure, two regions were selected, namely, top and bottom. Microstructural analyses revealed that both regions were primarily composed of acicular ferrite, polygonal ferrite, and bainitic structures. The bottom region exhibited superior mechanical properties compared with the top region. The improved strength at the bottom region can be ascribed to the formation of a high density of dislocations and finer grains.

Evolution of microstructure and mechanical property enhancement in wire-arc directed energy deposition with interlayer machining

Wire-Arc Directed Energy Deposition (Wire-Arc DED) has emerged as a promising additive manufacturing technique known for its high deposition rates. However, the variability in microstructure and mechanical properties (e.g., hardness) of the manufactured components poses significant challenges. This study delves into these issues, focusing on the influence of interlayer machining on the microstructural evolution and mechanical properties of thin-wall Wire-Arc DED structures. It is shown that as-built Wire-Arc DED structures exhibit a pronounced microstructure variation between different regions along the build direction, primarily governed by the differences in thermal history. In contrast, a Hybrid Wire-Arc DED process that integrates interlayer machining into the build process to induce severe plastic deformation leads to a microstructure characterized by refinement and homogenization, compared to a Wire-Arc DED process. This study provides insights into the impacts of plastic deformation due to machining and thermal cycling due to subsequent layer depositions on the microstructure and hardness obtained in Wire-Arc DED and Hybrid Wire-Arc DED processes, highlighting the potential of hybrid manufacturing to generate tailored microstructures to enhance the mechanical performance of functional components.

Study on the effect of particles in oilfield produced water on the deposition process of CaCO3

In crude oil production, scale deposition significantly reduces production output and elevates operational costs, posing a severe threat to production safety. While chemical methods have been extensively explored for the scaling and inhibition of inorganic salts, the inorganic scaling triggered by solid particle scaling in complex oilfield water has largely been overlooked. This study involves the introduction of particles into a supersaturated CaCO3 solution, utilizing static scale inhibition and conductivity techniques to examine their influence on the scaling process and crystallization rate. It is evident that solid particles expedite the deposition process of CaCO3. Moreover, the deposition rate of CaCO3 is influenced by factors such as the solid particle content, particle size, and stirring speed. It is noteworthy that the presence of solid particles solely impacts the formation rate of CaCO3 crystals, without altering the total deposition. Specifically, under conditions of 70°C, 250/min stirring speed, and 0.08% SiO2 addition, the deposition rate of CaCO3 is enhanced by 13.5%. The nucleus growth rate constant increases from 11.10 × 10-3min-1 to 14.52 × 10-3min-1 and the crystal growth rate constant increases from 3.02 × 10-3min-1 to 3.36 × 10-3min-1 at most. Observations made through scanning electron microscopy (SEM) and polarized light microscopy reveal that scaling occurs predominantly on the added solid particles in later stages, indicating that solid particles in supersaturated solutions serve as crystal nuclei, inducing the growth of CaCO3 crystals and thus accelerating scaling. This research provides valuable insights for the study of scaling in complex water environments.

An Effect of Al on the Properties of ZnIn2Se4 Thin Film

Abstract Zinc-indium-selenide ZnIn2Se4 (ZIS) ternary chalcopyrite thin film on glass with a 500 nm thickness was fabricated by using the thermal evaporation system with a pressure of approximately 2.5×10−5 mbar and a deposition rate of 12 Å/s. The effect of aluminum (Al) doping with 0.02 and 0.04 ratios on the structural and optical properties of film was examined. The utilization of X-ray diffraction (XRD) was employed to showcase the influence of aluminum doping on structural properties. XRD shows that thin ZIS-pure, Al-doped films at RT are polycrystalline with tetragonal structure and preferred (112) orientation. Where the degree of crystallinity is raised. The effect of Al content on surface roughness and average diameter was studied by atomic force microscopy (AFM), which showed that both surface roughness and average diameter increased with an increasing Al ratio until they reached their maximum values of 12.93 nm and 61.56 nm, respectively. Optical characteristics of ZIS thin film and the impact of aluminum on optical parameters have been investigated, and it was found that the optical energy ( E g opt ), absorption coefficient (α), extinction coefficient (k), refractive index (n), both the real (εr) and imaginary (εi) components of the dielectric constant have values of (1.8 eV), (3.11×104 cm−1), (0.111), (2.3), (5.36), and (0.517), respectively, for ZIS thin films at an Al ratio equal to 0.04.

Systemic Inflammation In Asymptomatic Hyperuricemia With Sonographic Crystal Deposits, Including A Comparison With Normouricemia And Gout.

To describe the inflammatory profile of asymptomatic hyperuricemia (AH) with ultrasound evidence of monosodium urate (MSU) crystals (AH-MSUpos), vs AH without deposits (AH-MSUneg), intercritical gout, and normouricemia. Based on serum urate levels, musculoskeletal ultrasound, and history of flares, we divided 122 participants into four groups: normouricemia, AH-MSUneg, AH-MSUpos, and intercritical gout. We tested four ultrasound definitions for MSU deposition in AH: grade 2-3 (G2-3) double contour and/or tophi, G1-3 double contour and/or tophi, G1-3 Stewart scheme (double contour sign in knee cartilage and/or first metatarsophalangeal joint and/or tophi in first metatarsophalangeal joint), and G2-3 Stewart scheme. Serum acute phase reactants, cytokines, pyroptosis derivates, and neutrophil-related proteins were measured and compared between groups. A linear regression model was fitted to correlate crystal and inflammatory burden (measured by ultrasound) with inflammatory markers in hyperuricemics. Rates of MSU deposition in AH ranged from 26.0% to 68.8%, depending on the definition used. Levels of CRP, leukocytes, IL-1RA, IL-6, sIL-6R, IL-18, TNF-α, TGF-β, and galectin-3 were higher in hyperuricemics vs normouricemics. Sex, obesity, and comorbidity scores influenced some comparisons. We saw no differences comparing AH-MSUpos vs AH-MSUneg groups, except for higher calprotectin using G1-3 sonographic definitions and higher CRP and TGF-β when restricted to women and obese participants. Hyperuricemia is associated with substantial inflammation and some degree of active pyroptosis. Four different ultrasound definitions for AH with MSU deposits yielded similar findings, although we noted some differences in calprotectin, CRP, and TGF-β. Sex, obesity, and comorbidities influenced some inflammatory responses.