Rare Earth Research Articles

The Use of Fuzzy Modelling Based on Expert Knowledge to Determine Poland’s Energy Security Index Taking into Account Political Conditions

This article presents the results of research on the energy security index in Poland. Since the development of renewable energy sources forced by the transformation of the national energy system will require an increased supply of rare earth elements, the level of demand for these metals was taken into account when determining the energy security index. Furthermore, the development of renewable energy sources in Poland will directly depend on the volume of energy demand and, as the events of previous years have shown, on political and legal conditions, especially in the case of wind energy. Since some of these factors are qualitative, it was impossible to use a quantitative method. Therefore, fuzzy sets were used. Fuzzy modelling is based on expert knowledge. Using this method, the authors created three alternative scenarios for the development of Poland’s energy security index: pessimistic, optimistic, and the most probable.

Broad spectral response of Y-NaBi(MoO4)2@NaYF4:Yb, Tm photocatalysts for efficient degradation of ciprofloxacin: Upconversion mechanism and theoretical calculations

In this work, a novel Y-NaBi(MoO4)2@NaYF4:Yb, Tm composite was successfully synthesized for the first time by hydrothermal method. The lamellar Y-NaBi(MoO4)2 was dispersed on the surface of the hexagonal prism NaYF4:Yb, Tm without aggregation. The composite achieved a broad spectral response. The NaYF4:Yb, Tm absorbed near-infrared light and emitted ultraviolet and visible light by the energy transfer upconversion process. The emitted light was reabsorbed by Y-NaBi(MoO4)2 through the fluorescence resonance energy transfer process. Moreover, the doping of Y3+ ions enhanced the light response capability of the composite. The experimental results revealed that the photocatalytic degradation efficiency of ciprofloxacin (CIP) reached 96.2 % after 180 min of illumination under simulated sunlight. Meanwhile, the degradation pathways and attack sites of CIP were intensively investigated by liquid chromatography-mass spectrometry analysis and density functional theory theoretical calculations. The upconversion process, the separation of photogenerated carriers and rare earth metal ion doping all contributed to the high effective photodegradation. This work provided a new strategy for effective utilization of solar energy for the degradation of emerging pollutants to mitigate environmental pollution.

Physical and Geochemical Characterisation of Pongo Pitti and Bossambo Farm Clays (Littoral Region, Cameroon) for use in Ceramics

The main objective of this work is to discern the physico-chemical and mechanical behavior of the Pongo Pitti and Bossambo Farm clay formations, located on either side of the Sanaga river in the littoral region of Cameroon. To achieve this, two field campaigns and laboratory works were carried out. Four clay materials were collected and brought back to the laboratory. The laboratory investigations involved physico-mechanical and geochemical analyses, followed by ceramic testing. The materials studied have a clayey texture, with clay percentages ranging from 26.89% to 80.3%, silt from 13.2% to 57.6% and sand from 1.58% to 47.26%. The plasticity index ranges from 11.9% to 24.2%. From a geochemical standpoint, the materials studied show a predominance of silica (49.6% to 63.5%), alumina (20.5% to 27.1%) and iron (2.39% to 8.6%), with the SiO2/Al2O3 ratio varying from 1.96 to 3.1. The Al2O3/Fe2O3 ratio is 8.4 for Pongo Pitti clays and 2.9 for Bossambo Farm clays. The geochemical weathering indices (ICV, CIA, PIA, CIW, CIW) show a high degree of weathering, with values in excess of 90%. Alkali and alkaline-earth proportions are lower, and the K2O/Na2O ratio varies between 8.45 and 14.24, showing an enrichment of potassium in relation to sodium. Lantane is the most abundant rare-earth element (323.84 ppm). The REE study shows a predominance of light REEs over heavy REEs (LREE/HREE~4.51) and a negative Europium anomaly. Infrared spectroscopy showed poor kaolinite crystallinity. Mechanically, the specimens studied, fired at temperatures ranging from 950℃ to 1050℃ showed good cohesion and metallic soundness. Linear shrinkage was 4.8%. Mass loss increases with temperature. Its value is 12.5% for Pongo Pitti materials and 8.5% for Bossambo Farm materials. Water absorption decreases with temperature and is 20.27% for Pongo Pitti samples and 15.79% for Bossambo Farm samples. Bulk density increases with temperature (2.11 at 950℃ to 2.51 at 1050℃). Flexural strength increases with temperature and is 6.66 MPa for materials from Pongo Pitti and 8.89 MPa for those from Bossambo Farm. These materials can be used to make fired bricks and roof tiles, and Pongo Pitti materials can be used to make refractory ceramics

Preparation of 97% pure nickel-cobalt alloy from waste Ni-MH batteries by using waste glass as a fluxing agent

With the e-waste growing rapidly all over the globe due to growing demand of electronics, smartphones, etc., coming up with an efficient and sustainable recycling process is the need of the hour. The present work reports a novel and sustainable process of manufacturing Ni alloy by bringing together three major waste streams such as waste Ni-MH batteries, e-waste plastics, and waste glass. The chosen temperature (1550 °C) favours the reduction of nickel-oxide by e-waste plastic as the reductant and sends rare earth elements present in the waste Ni-MH battery as oxide mixture to the slag phase. Waste glass powder used in this process functions as the fluxing agent, hence not requiring any additional flux. The reduction mechanism is gas-based, controlled mainly by hydrogen and carbon monoxide gases released as a result of decomposition of e-waste plastic as reaction commenced from cold zone (∼300 °C) to hot zone (1550 °C) in the horizontal tubular furnace. Formation of nickel alloy and enrichment of slag with mixture of rare earth oxides were confirmed by XRD, SEM-EDS, and Rietveld refining analysis performed on the XRD spectra of slag phase. ICP-OES (Inductively coupled plasma optical emission spectroscopy) and LIBS (laser induced breakdown spectrometer KT-100S) confirmed the high metal content in the alloy, thereby emphasizing the purity (∼98%) which is close to the composition of nickel super alloy. A maximum of 61% by weight REO enrichment was achieved in the slag phase, having La2O3:44.6%, Pr2O3:14.8%, and Nd2O3: 1.6% under optimised experimental conditions (1550 °C, 15 min, and 20% waste glass powder). This scientific investigation evinces a promising route for efficient utilisation of waste streams emanating from e-waste, thereby devising a sustainable recycling technique and protecting the environment, too.

Can Metal Promotion of SAPO-34 Genuinely Improve its Catalytic Performance in Methanol Conversion to Light Olefins Reaction?

To genuinely assess the effect of secondary metal promotion on improving the SAPO-34 catalytic performance in MTO reaction, a broad spectrum of metals from different groups of the periodic table (alkali and alkaline earth metals, transition metals, rare earth metals, and basic metals) were investigated. Metals were added through a direct incorporation route with Me/Al2O3 molar ratio of 0.05. Some metals seamlessly incorporated into the SAPO-34 framework and replaced the Si and Al atoms, while others partially merged or even failed to be combined with SAPO and emerged as amorphous phases. Although, in some cases, the surface area of the metal-promoted samples increased due to enhanced nucleation rate and smaller particle formation, the majority of the promoted samples suffered from a severe loss in crystallinity that resulted in inferior catalytic performance. It was also illustrated that hydrogen co-feeding with methanol (H2/MeOH molar ratio of 1.5) at ambient pressure could extend the catalyst lifetime by 27% due to hydrogenation and cracking of the coke species and improve the light olefins selectivity.

Structural, morphological, optical and down-conversion studies of NaLaMgTeO6:Dy3+ single phase phosphor for white light emitting applications and solar spectral converter for photovoltaic applications

Researches on rare earth activated phosphors in solid state lighting and enhancement in efficiency of solar cells pave attention to develop efficient phosphor materials. In the present work, Dy3+ doped NaLaMgTeO6 phosphors are synthesized using solid state reaction method. The structural studies using XRD analysis confirmed the successful formation of the compound. SEM analysis reveals that the particles are closely packed, which in turn exhibit intense luminescence intensity due to low scattering and high packing density. Elemental configuration were analyzed using EDS analysis. FTIR analysis revealed the vibrational bands of the host matrix. Optical energy bandgap was calculated using DRS spectra. The luminescence characteristics of the samples were investigated using excitation and emission spectra. Upon most intense 351 and 388 nm excitation, sharp yellow emission peak at 572 nm dominates blue emission at 478 nm, further reveals that Dy3+ ions occupy low symmetry site in the host lattice. The optimum concentration of Dy3+ in the present host is x = 0.04 mol and concentration quenching is due to dipole-quadrupole interaction of adjacent Dy3+ ions. The thermal quenching phenomenon is studied using temperature dependent photoluminescence analysis. The CIE chromaticity coordinates and CCT values conclude NaLaMgTeO6:Dy3+ phosphors are good candidate for cool near-white light emitting materials for outdoor illumination. The study on solar spectral response and down-conversion property of the synthesized phosphor demonstrate its applicability as solar spectral converters in solar cell applications.

Efficient Adsorption and Elimination of Tm3+ for Enhanced Seed Germination Using Pillar[5]Arene Polymer.

While rare earth elements (REEs) are essential for modern technology, their production methods raise concerns for agriculture. Researchers are now exploring ways to control and recycle REEs pollution, aiming to minimize agricultural impacts and potentially even develop methods to utilize these elements for improved crop yields. Regarding this issue, a new type of pillar[5]arene polymer (Pol-P[5]-BTZP) has been designed and synthesized by click reaction to enhance the efficiency of adsorption and recovery of rare earth metals. This polymer incorporates the unique structure of 2,6-di-1,2,3-triazolyl-pyridine. The results of various analyses revealed that Pol-P[5]-BTZP exhibits excellent thermal stability, a high specific surface area, and well-distributed networks of micropores and mesoporous structures. The adsorption capacity of Pol-P[5]-BTZP for Tm3+, a representative REE, was evaluated using the Langmuir and Freundlich isothermal adsorption models with a maximum adsorption capacity (Qmax) of 127.71 mg/g. Furthermore, the versatility of Pol-P[5]-BTZP in adsorption and recovering various REEs was tested. In addition to its adsorption capabilities, the potential of Pol-P[5]-BTZP for rare earth recovery and reuse was assessed through experiments on the impact of Tm3+ and La3+ on seed germination. These experiments demonstrated the wide-ranging applicability of Pol-P[5]-BTZP in recovering and reusing REEs for green agriculture.

The rare-earth elements recovered from the leachate of discarded phosphor by electrodeposition

ABSTRACT Recovering rare-earth elements (REEs) from discarded phosphors is an important solution to alleviate the current shortage of rare-earth resources, the aluminum element in discarded phosphors will badly affect the purity and recovery of rare-earth elements. An electrodeposition method for recovering the rare earth from the discarded phosphoric leachate was proposed to avoid the effecting of aluminum elements. The results show that the purity of the rare-earth oxides recovered reached 99.13% and the recovery rate of rare-earth elements reached 98.89% by adopting the optimal electrodeposition process with the help of the complexing agent glycine. Research has found that adding the complexing agent glycine can help rare-earth hydroxides precipitate at the cathode and inhibit aluminum ion precipitation by changing the aluminum deposition potential. Moreover, it was also found that the generation of OH- ions by reduction of NO3- in acid aqueous solution was a one-step irreversible reaction in the deposition process by cyclic voltammetry, which ensured the reliability of rare-earth hydroxide precipitation reaction.

Sediment-Hosted Rare-Earth Elements Mineralization from the Dian-Qian District, Southwest China: Mineralogy and Mode of Occurrence

The Xuanwei Formation’s claystones in the Dian-Qian District of Southwest China are rich in rare-earth elements (REEs), suggesting their potential as a source of medium and heavy rare earths. However, the REE content in these rocks is lower than other types of rare-earth deposits, and the interrelationship among clay minerals is intricate. There is no direct evidence indicating the mineralization of REEs, limiting their beneficiation and extraction. The objective of this study is the characterization of REE distribution in the Dian-Qian District. The sedimentary rocks in this district are mainly composed of kaolinite, boehmite, quartz, rutile, and pyrite. The results of continuous chemical extraction of REE-rich claystone and transmission electron microscope (TEM) observations have confirmed that REEs occurred as florencite in the rocks, and that the ion-absorption state makes only a negligible contribution to the REE content. A close relationship between florencite and kaolinite makes traditional mineral processing operations very difficult. Combined with the properties of kaolinite, roasting-acid leaching was the efficacious approach for rare-earth resources extracted from the rare earth-rich clay rocks of the Xuanwei Formation.

Investigation of the structural, thermo–electrical, and morphological properties of the Bi2O3 ceramics co–doped with rare earths

Investigation of the structural, thermo–electrical, and morphological properties of the Bi2O3 ceramics co–doped with rare earths

Inducing high-concentration Tb3+ with free oxygen via atomic layer deposition

Precise preparation and control of trivalent states in rare earth metal oxide films are crucial for their optical and magnetic applications. In this study, compact and continuous terbium-doped nanofilms were deposited on silica substrates using atomic layer deposition (ALD). The average nanoparticle size varied from 17.9 to 78.5 nm with increasing growth cycles. X-ray photoelectron spectroscopy showed that the Tb3+/Tb4+ ratio increased from 0.98 to 1.42. A valence reduction mechanism involving free oxygen was introduced to analyze the reasons for the enhanced Tb3+ concentration in the nanofilms. The enhanced photoluminescence of Tb3+ (5D4→7F5) ions and the increased magnetization in terbium oxide nanofilms both reveal that free oxygen ions are the effective active sites responsible for the transition from the tetravalent to the trivalent state, in excellent agreement with theoretical analysis. Size control and free oxygen induction are promising strategies for enhancing the optical and magnetic properties of multivalent rare earth oxides.

Fluorine Doping Mediated Epitaxial Growth of NaREF4 on TiO2 for Boosting NIR Light Utilization in Bioimaging and Photodynamic Therapy

AbstractBy integrating TiO2 with rare earth upconversion nanocrystals (NaREF4), efficient energy transfer can be achieved between the two subunits under near‐infrared (NIR) excitation, which hold tremendous potential in the fields of photocatalysis, photodynamic therapy (PDT), etc. However, in the previous studies, the combination of TiO2 with NaREF4 is a non‐epitaxial random blending mode, resulting in a diminished energy transfer efficiency between the NaREF4 and TiO2. Herein, we present a fluorine doping‐mediated epitaxial growth strategy for the synthesis of TiO2‐NaREF4 heteronanocrystals (HNCs). Due to the epitaxial growth connection, NaREF4 can transfer energy through phonon‐assisted pathway to TiO2, which is more efficient than the traditional indirect secondary photon excitation. Additionally, F doping brings oxygen vacancies in the TiO2 subunit, which further introduces new impurity energy levels in the intrinsic band gap of TiO2 subunit, and facilitates the energy transfer through phonon‐assisted method from NaREF4 to TiO2. As a proof of concept, TiO2‐NaGdF4 : Yb,Tm@NaYF4@NaGdF4 : Nd@NaYF4 HNCs were rationally constructed. Taking advantage of the dual‐model up‐ and downconversion luminescence of the delicately designed multi‐shell structured NaREF4 subunit, highly efficient photo‐response capability of the F‐doped TiO2 subunit and the efficient phonon‐assisted energy transfer between them, the prepared HNCs provide a distinctive nanoplatform for bioimaging‐guided NIR‐triggered PDT.

Complexation of ThoriumIV with Fluorinated Heterocyclic β‐Diketones in Aqueous Hydrochloric Solutions

AbstractThe interaction of Thorium(IV) with a group of non‐symmetric CF3‐diketones has been studied by means of electronic absorption spectroscopy in HCl aqueous solutions at I=0.5 M (NaCl) and T=298 K. Six heterocyclic dicarbonyl ligands (2‐thenoyl‐trifluoroacetone, 2‐furoyl‐trifluoroacetone, 2‐selenophen‐trifluoroacetone, 2‐tellurophen‐trifluoroacetone, phenyl‐trifluoroacetone, and 2‐naphthyl‐trifluoroacetone) demonstrate the chelation activity toward ThIV in the acidic pH range. Obtained values of the “true” stability constants lie in the range 6.2–6.8 logarithmic units, respectively. A significant (10–15 nm) bathochromic shift between the maximum absorption wavelength of lanthanide and actinide monocomplexes has been detected. Observed spectral shift increases with the atomic number of substituted chalcogen atoms in the heterocyclic ring of the corresponding ligand: 10 nm for furan, 11 nm for thiophen, 14 nm for selenophen, and 15 nm for tellurophene rings. The complexation with Thorium occurs in an acidic media, where studied ligands do not interact with transition and rare earth metals. Spectral and pH shifts make studied ligands useful reagents for the detection and analytical determination of Thorium in the mixture with other metals without prior separation. Quantum‐chemical simulations (DFT and TD‐DFT) demonstrate that the nine‐ and deco‐coordinated structures of ThoriumIV complexes reproduce experimental values within reasonable errors.

Synthesis and Upconversion Luminescence Fine-tuning of Yb3+/Ho3+-Doped Indium and Gallium Oxide Nanoparticles.

Rare earth (RE) dopants can modulate the bandgap of oxides of indium and gallium and provide extra upconversion luminescence (UCL) abilities. However, relevant UCL fine-tuning strategies and energy mechanisms have been less studied. In this research, InGaO, Ho3+ monodoped and Yb3+/Ho3+ codoped In2O3, and Ho3+ monodoped Yb3Ga5O12 nanoparticles (NPs) were synthesized by a solvothermal method. The effects of Yb3+ and Ho3+ dopants on the crystal structures, UCL properties, and optical bandgaps of the oxides were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UCL spectroscopy, and measurements of decay times, pump power dependence, and transmittance spectra. The crystal structures of oxide products of indium and gallium were significantly modified with RE dopants. In2O3 and Yb3Ga5O12 were selected as the host materials. For Yb3+/Ho3+ codoped In2O3 NPs, there existed energy transfers from the defect states of In2O3 to Ho3+ and from Yb3+ to Ho3+. With a fixed Ho3+ concentration, In2O3:0%Yb3+,2%Ho3+ NPs showed the optimal UCL properties mainly due to In2O3-Ho3+ energy transfer and Ho3+-Yb3+ energy-back-transfer, while with a fixed Yb3+ concentration, In2O3:5%Yb3+,3%Ho3+ NPs with a slight Yb2O3 impurity and Yb3Ga5O12:2%Ho3+ NPs did mainly due to Ho3+-Ho3+ cross-relaxation. Besides, the optical bandgaps of In2O3 and Yb3Ga5O12 were noticeably broadened with RE dopants. These findings can offer feasible directions for the synthesis and UCL fine-tuning of RE-doped oxides of indium and gallium and improve their multifunction application prospects in the fields of semiconductor and UCL nanomaterials.

Oxygen ion diffusion in RE3TaO7: Why long-range migration of O2− is prohibited in the defective-fluorite structure?

Oxides with low O2− lattice diffusion rate are critical for the development of topcoat materials for next generation thermal barrier coatings (TBCs) working at > 1600 °C to prevent the fast growth of thermally grown oxide (TGO) at the bondcoat/topcoat interface. Here we delve into a comprehensive analysis of the oxygen ion transport characteristics of the recently developed low-, medium- and high-entropy rare earth tantalates (RE3TaO7) for TBCs by a combination of impedance spectroscopy, 18O isotope diffusion tests and atomic-scale simulations. Results show that the RE3TaO7 series display remarkably low oxygen ion diffusion rate (> 3 orders of magnitude lower than the state-of-the-art topcoat material yttria stabilized zirconia, YSZ) despite the presence of abundant oxygen vacancies in the structure. Molecular dynamic (MD) simulations combined with first principles calculations reveal that oxygen ions are strongly trapped by the potential well at the Ta-Ta edge in the tantalates. In addition, the high electrostatic potential (EP) surrounding oxygen vacancies and the high diffusion barriers between rare earth elements also impede oxygen ion diffusion. With low oxygen ion diffusion rate, along with exceptional thermal and mechanical properties reported previously, RE3TaO7 are promising topcoat materials for next-generation TBCs working at higher temperatures. Moreover, this study also provides valuable insights for understanding the O2− lattice diffusion behaviour in RE3TaO7 with a defective fluorite structure, which may benefit the exploration of oxide-ion conductors.

Assessment of potential toxic elements in soils, sediments, and vegetation in the surroundings of Anapa, Russia.

The study presented here reports the concentration of major, trace, and rare earth elements in soil, sediments, and vegetation samples collected from 13 locations around Anapa City located on the northern coast of the Black Sea in Russia. The neutron activation analysis technique has been used to fulfill this objective. Along with this, the bioconcentration and translocation factors were calculated. Overall, the content of 31 elements was detected in soil and sediments while 20 elements were determined in three types of vegetation: macroalgae (Cystoseira sp. and Ulva sp.), aquatic plants (Phragmites australis), and sea grass (Zostera sp.). The quantified concentration followed the order soil > sediment > vegetation. The phytotoxic levels for Zn, V, Mn, and Fe have been quantified as the highest. Bromine was the most abundant and accumulated in Phragmites australis. Based on the results obtained from this investigation, there is a possibility of contamination in the study area.

Synthesis of Rare Earth Metal Complexes Stabilized by Amine Bridged Bis(phenolato) Ligands and Their Performance in the Polymerization of rac-β-Butyrolactone.

A series of rare earth alkoxides bearing amine-bridged bis(phenolato) ligands were synthesized through sequential reactions of RE(C5H5)3(THF) (RE = Y, Lu) or Nd[N(SiMe3)2]3 with bis(phenols) LH2 and CF3CH2OH. Complexes REL(OCH2CF3)(THF)n (1-6) bearing different aryl-substituents were obtained in good yields of 59-70%. They were applied in the ring-opening polymerization (ROP) of rac-β-butyrolactone (rac-BBL), which showed good activity (TOF up to 27,300 h-1), resulting in syndiotactically enriched poly(3-hydroxybutyrate) (PHB) (Pr up to 0.86) with narrow polydispersities (PDI ≤ 1.27). The yttrium complex 3 bearing bulky o-1,1-diphenylethyl substituents outperformed other complexes, suggesting that the smaller ionic radii of metal centers and bulky ortho substituents of ancillary ligands play crucial roles in controlling the activity and stereoselectivity in ROP of rac-BBL. Kinetics of the polymerization of rac-BBL initiated by complex 3 was investigated, which revealed first order dependences on the monomer and initiator concentrations, respectively.

Leaching Behavior and Leaching Mechanism Analysis of Pb in Soil Under the Action of Sulfate Leaching Agent: A Case Study of Ion-Adsorption Rare Earth Mining Area

Leaching Behavior and Leaching Mechanism Analysis of Pb in Soil Under the Action of Sulfate Leaching Agent: A Case Study of Ion-Adsorption Rare Earth Mining Area

Fluorine Doping Mediated Epitaxial Growth of NaREF4 on TiO2 for Boosting NIR Light Utilization in Bioimaging and Photodynamic Therapy.

By integrating TiO2 with rare earth upconversion nanocrystals (NaREF4), efficient energy transfer can be achieved between the two subunits under near-infrared (NIR) excitation, which hold tremendous potential in the fields of photocatalysis, photodynamic therapy (PDT), etc. However, in the previous studies, the combination of TiO2 with NaREF4 is a non-epitaxial random blending mode, resulting in a diminished energy transfer efficiency between the NaREF4 and TiO2. Herein, we present a fluorine doping-mediated epitaxial growth strategy for the synthesis of TiO2-NaREF4 heteronanocrystals (HNCs). Due to the epitaxial growth connection, NaREF4 can transfer energy through phonon-assisted pathway to TiO2, which is more efficient than the traditional indirect secondary photon excitation. Additionally, F doping brings oxygen vacancies in the TiO2 subunit, which further introduces new impurity energy levels in the intrinsic band gap of TiO2 subunit, and facilitates the energy transfer through phonon-assisted method from NaREF4 to TiO2. As a proof of concept, TiO2-NaGdF4 : Yb,Tm@NaYF4@NaGdF4 : Nd@NaYF4 HNCs were rationally constructed. Taking advantage of the dual-model up- and downconversion luminescence of the delicately designed multi-shell structured NaREF4 subunit, highly efficient photo-response capability of the F-doped TiO2 subunit and the efficient phonon-assisted energy transfer between them, the prepared HNCs provide a distinctive nanoplatform for bioimaging-guided NIR-triggered PDT.

Highly Efficient and Precise Rare-Earth Elements Separation and Recycling Process in Molten Salt

Owing to the worldwide trend towards carbon neutrality, the number of Dy-containing heat-resistant Nd magnets used for wind power generation and electric vehicles is expected to increase exponentially. However, rare earth (RE) elements (especially Dy) are unevenly distributed globally. Therefore, an environmental-friendly recycling method for RE elements with a highly precise separation of Dy and Nd from end-of-life magnets is required to realize a carbon-neutral society. As an alternative to traditional hydrometallurgical RE separation techniques with a high environmental load, we designed a novel, highly efficient, and precise process for the separation and recycling of RE elements from magnet scrap. As a result, over 90% of the RE elements were efficiently extracted from the magnets using MgCl2 and evaporation loss was selectively suppressed by adding CaF2. The extracted RE elements were electrolytically separated based on the formation potential differences of the RE alloys. Nd and Dy metals with purities greater than 90% were estimated to be recovered at rates of 96% and 91%, respectively. Almost all the RE in the scraps could be separated and recycled as RE metals, and the byproducts were easily removed. Thus, this process is expected to be used on an industrial scale to realize a carbon-neutral society.