Radio Frequency Antenna Research Articles

Intelligent Ureteral Stent Placeable via Standard Procedure for Kidney Pressure Telemetry: An Ex-Vivo Study.

This paper reports the first telemetric ureteral stent compatible with common placement procedure, enabling wireless sensing and detection of ureteral obstruction and resultant kidney swelling known as hydronephrosis at an early stage. This sensor-integrated "intelligent" ureteral stent is prototyped via the design and fabrication approaches that raise the practicality of the device and tested in a harvested swine kidney-ureter model ex vivo. Leveraging a polymeric double-J stent and micro-electro-mechanical systems technology, the intelligent stent is built by embedding micro pressure sensors and a radiofrequency antenna, forming a resonant circuit that enables wireless kidney pressure monitoring in an operating frequency of 40-50MHz. The stent device is entirely packaged with Parylene-C for both biocompatibility and electrical insulation of the device in order to function in the real environment including urine, an electrically conductive liquid. A comparison between the results measured in in-vitro and ex-vivo settings show a good match in the sensitivity to applied pressure. In particular, the ex-vivo test in the kidney-ureter model pressurized with artificial urine in a cycled manner demonstrates wireless pressure tracking with a response of 1.3kHz/mmHg, over pressures up to 37mmHg that well covers a range of pressure increase known for chronic obstruction. This testing is enabled by the prototype placement into the ex-vivo model using the standard stenting technique and tools without noticeable functional degradation or failures, showing potential compatibility of the device with today's clinical need as a ureteral stent.

Design and research of high-frequency electromagnetic wave detection antenna for discharge of transmission lines

Abstract Overhead lines have a wide range of applications in power systems. When early insulation faults occur in the long-term operation of overhead lines, corona discharge may occur. Timely detection of corona discharge can guide maintenance personnel to discover and eliminate faults in a timely manner. The height and distribution of overhead lines are relatively high, and close-range detection cannot quickly locate the discharge area. Using radio frequency antennas to measure the electromagnetic wave signals generated by corona discharge can achieve long-distance positioning detection of corona discharge. This article uses a log-periodic antenna as the detection antenna and simulates the antenna structure to prove that its directionality, gain, and measurement frequency band meet the design requirements. Finally, the discharge detection performance of the antenna is verified through experiments.

Doppler sensitivity and resonant tuning of Rydberg atom-based antennas

Radio frequency antennas based on Rydberg atom vapor cells can in principle reach sensitivities beyond those of any conventional wire antenna, especially at lower frequencies where very long wires are needed to accommodate the increasing wavelength. They also have other desirable features such as consisting of nonmetallic, hence lower profile, elements. This paper presents a detailed theoretical investigation of Rydberg antenna sensitivity, elucidating parameter regimes that could cumulatively lead to a sensitivity increase 2–3 orders of magnitude beyond that of currently tested configurations. The key insight is to optimally combine the advantages of two well-studied approaches: (i) three laser ‘2D star configuration’ setups that, when enhanced with increased laser power, to some degree compensate for atom motion-induced Doppler broadening, and (ii) resonant coupling between a pair of near-degenerate Rydberg levels, tuned via a local oscillator to the incident signal of interest. The advantage of the star setup is subtle because it only restores the overall sensitivity to the expected Doppler-limited value, compensating for additional significant off-resonance reductions where differently moving atom sub-populations destructively interfere with each other in the net signal. An additional unique advantage of local oscillator tuning is that it leads to vastly narrower line widths, as low as ∼10 kHz set by the intrinsic Rydberg state lifetimes, rather than the typical ∼10 MHz scale set by the core state lifetimes. Intuitively, with this setup the two Rydberg states may be tuned to act as an independent high-q cavity, a point of view supported by a study of the frequency-dependence of the antenna resonant response. There are a number of practical experimental advances, especially larger ∼1 cm laser beam widths, required to suppress various extrinsic line broadening effects and to fully exploit this ‘Rydberg superheterodyne’ response.

Highly Conductive and Long-Term Stable Phosphorene-Based Nanocomposite for Radio-Frequency Antenna Application.

In this study, an omnidirectional and high-performance free-standing monopole patch radio-frequency antenna was fabricated using a urea-functionalized phosphorene/TiO2/polypyrrole (UTP) nanocomposite. The UTP nanocomposite antenna was fabricated via ball milling of urea-functionalized phosphorene, chemical oxidative polymerization of the UTP nanocomposite, and mechanical pelletizing of the composite. Based on experiments, the proposed UTP nanocomposite-based antenna exhibited long-term stability in terms of electrical conductivity. After 12 weeks, a slight change in surface resistance was observed. The proposed antenna exhibited high radiation efficiency (78.2%) and low return loss (-36.6 dB). The results of this study suggest the potential of UTP nanocomposite antennas for applications in 5G technology.

ICRH-related impurity source and control across experiments in H, D, T plasmas at JET-ILW

The experimental and theoretical analysis were focused on experiments conducted to assess the effect of plasma isotopes, protium (H), deuterium (D), and tritium (T) on ion cyclotron resonance heating (ICRH) related plasma wall interactions. Comparison of L-mode discharges with N = 1 3He and N = 1 H minority ICRH heating scenarios were done for different isotopes. For the selected pulses, the behaviour of high-Z, mid-Z and low-Z intrinsic impurity and radiated power behaviour was investigated based on data from VUV, visible spectroscopy, and bolometry diagnostic at Joint European Torus. It was found that for N = 1 3He scenario during radiofrequency antennas operation, core W, Ni content, Be source and the radiated power are higher for π/2 in comparison to dipole antenna phasing. Lowest core Ni, W content and radiated power is clearly observed for H plasmas in comparison to D and T, where for this ICRH scenario behaviour was similar. However, lower Be photon flux is observed for T in comparison to D plasmas. Be sputtering by He particles is responsible for such an effect. Additionally, several computer simulations were conducted using the COREDIV code. The difference in the electron temperature was due to the difference in the isotope masses. Increased temperature in the central plasma in the case of T plasmas leads to higher radiation in the central plasma in comparison to H plasmas. As a result, the power across separatrix is lower and the temperature on the divertor plate decreases with the increase of the isotope mass. At these temperatures on the divertor plate, W is not sputtered by the main plasma ions H, D and T and by He. For the N = 1 H ICRH scenario clear difference between D and T plasma was observed with higher metallic impurity content for T plasma in comparison to D. Impurity content in the plasmas is found to be sensitive to the power balance between the antenna straps. Its minimum is observed for the maximum of P cen/P tot.

Development of a field-reversed configuration device using radio frequency antennas to produce E × B for current-drive

A unique field-reversed configuration (FRC) experiment is presently being assembled at the Plasma Technology Research Institute, KFE. It is a compact small-scale FRC device, which uses a set of radio frequency (RF) antennas to produce an internal E × B that drives the electrons for current-drive, in which E is the electric field and B is the magnetic field. This is very similar to the rotating magnetic field (RMF) current-drive, where the horizontal and vertical antennas are driven 90° out of phase. For this device, the RF antennas are arranged differently than the RMF. The RF antennas, being two separate sets, are positioned inside the vacuum chamber. Each set consists of 8 coils, for a total of 16 coils, where 80~100 kHz sine and cosine waveform currents are applied. One set of coils generates a radial B-field, while the other set provides an E-field in the z-direction. As the phase changes, the E and B fields are switched by these two sets. Nevertheless, E × B propagates in the same θ-direction so that this allows the electrons to rotate around the circumference of the device. The FRC device will test wave heating by launching 2.45 GHz microwaves. Also, passive stabilizers are positioned at each end to provide extra stability while preventing tilt instability. The experiment is expected to produce its first plasma in 2025.

Dual Frequency Energy Harvesting System Based on Planar Inverted F-shaped Antenna

<p>With the expansion of Internet of things (IoT) scale and the extension of its application fields, node energy acquisition has become one of the constraints on the development and application of IoT technology. Wireless energy acquisition is faced with the challenge of how to enhance power conversion efficiency under low input power in the broadband range. This study aimed to improve the capability of energy collection and transmission in wireless communication, an efficient dual-frequency energy harvesting system was proposed, moreover a novel dual-frequency planar inverted-f antenna (PIFA) and its energy conversion circuit for Radio frequency (RF) energy harvesting were designed by studying the characteristics of ambient RF energy and antenna. The developed antenna is designed and manufactured for GSM 900mhz or DCS 1.8 GHz to harvest the ambient energy provided by nearby devices. It is proved that the new dual-frequency antenna still has high efficiency when the input power is less than -20 dbm, and can maximize the receiving energy. The system works with an energy conversion and storage module to convert weak signals into required voltages, the simulation and test results show that the maximum conversion efficiency of the prototype is about 65% at 920MHZ and 1.8GHz at -20 dBm input power.</p> <p> </p>

Actuation Modeling of a Microfluidically Reconfigurable Radiofrequency Device

Abstract Microfluidic-based techniques have been shown to address limitations of reconfigurable radio frequency (RF) antennas and filters in efficiency, power handling capability, cost, and frequency tuning. However, the current devices suffer from significant integration challenges associated with packaging, actuation, and control. Recent advances in reconfigurable microfluidics that utilize the motion of a selectively metalized plate (SMP) for RF tuning have demonstrated promising RF capabilities but have exposed a need for an accurate fluid actuation model. This research presents a model for the mechanical motion of a moving plate in a channel to relate the SMP size, microfluidic channel size, velocity, and inlet pressure. This model facilitates understanding of the actuation response of an RF tuning system based on a moving plate independent of the actuation method. This model is validated using a millimeter-scale plate driven by a gravitational pressure head as a quasi-static pressure source. Measurements of the prototyped device show excellent agreement with the analytical model; thus, the designer can utilize the presented model for designing and optimizing a microfluidic-based reconfigurable RF device and selecting actuation methods to meet desired outcomes. To examine model accuracy at device scale, recent papers in the microfluidics reconfigurable RF area have been studied, and excellent agreement between our proposed model and the literature data is observed.

Predicting the antenna properties of helicon plasma thrusters using machine learning techniques

When designing helicon plasma thrusters, one important characteristic is the impedance of the radio-frequency antenna that is used to deposit power into the plasma. This impedance can be characterized both experimentally and numerically. Recently, a numerical tool capable of predicting the antenna impedance, called Adamant, has been developed. However, Adamant takes a long time to run and has high computer resource demands. Therefore, this work has been done to evaluate whether machine learning models, trained on Adamant-generated data, can be used instead of Adamant for small design change evaluations and similar works. Six different machine learning models were implemented in MATLAB: decision trees, ensembles, support vector machines, Gaussian process regressions, generalized additive models and artificial neural networks. These were trained and evaluated using nested k-fold cross-validation with the hyperparameters selected using Bayesian optimization. The performance target was to have less than 5% error on a point-to-point basis. The artificial neural network performed the best when taking into account both maximum error magnitudes and generalization ability, with a maximum error of 3.98% on the test set and with considerably better performance than the other models when tested on some practical examples. Future work should look into different solver algorithms for the artificial neural network to see if the results could be improved even further. To expand the model’s usefulness it might also be worth looking into implementing different antenna types that are of interest for helicon plasma thrusters.

Wireless Sensor for Meat Freshness Assessment Based on Radio Frequency Communication.

Wireless communication technologies, particularly radio frequency (RF), have been widely explored for wearable electronics with secure and user-friendly information transmission. By exploiting the operational principle of chemically actuated resonant devices (CARDs) and the electrical response observed in chemiresistive materials, we propose a simple and hands-on alternative to design and manufacture RF tags that function as CARDs for wireless sensing of meat freshness. Specifically, the RF antennas were meticulously designed and fabricated by lithography onto a flexible substrate with conductive tape, and the RF signal was characterized in terms of amplitude and peak resonant frequency. Subsequently, a single-walled carbon nanotube (SWCNT)/MoS2/In2O3 chemiresistive composite was incorporated into the RF tag to convey it as CARDs. The RF signal was then utilized to establish a correlation between the sensor's electrical response and the RF attenuation signal (reflection coefficient) in the presence of volatile amines and seafood (shrimp) samples. The freshness of the seafood samples was systematically assessed throughout the storage time by utilizing the CARDs, thereby underscoring their effective potential for monitoring food quality. Specifically, the developed wireless tags provide cumulative amine exposure data within the food package, demonstrating a gradual decrease in radio frequency signals. This study illustrates the versatility of RF tags integrated with chemiresistors as a promising pathway toward scalable, affordable, and portable wireless chemical sensors.

Results for the London investigation into dielectric scanning of lesions study of the MARIA® M6 breast imaging system.

Determine the proportion of breast cancers for which MARIA® findings correspond to the cancer, with stratification by breast density and histological type. Investigate performance in symptomatic lesions. Gain patient feedback on experience with MARIA®. MARIA® uses a radio frequency antennae array to measure signal attenuation and back scatter to build up a 3D map of tissue dielectric values. The study was a prospective, single-centre, interventional, post-approval device study. Patients were eligible if they were attending symptomatic breast clinic or had confirmed or suspected breast cancer from any referral source. Recruitment between May 2018 and March 2020. Regions of higher signal compared to background or distinct by shape were considered candidates for lesion correspondence. Up to 4 candidate regions per breast were annotated in likelihood order for representing a true lesion. 389 patients were recruited, and 6 excluded. 114 patients recruited with breast cancers (2 bilateral, 5 multicentric). 57 (47%) malignant lesions showed correspondence between the MARIA® signal and the cancer. Higher correspondence was seen in invasive (50%) than in situ (29%) disease. There was no reduction in correspondence at higher breast density. Reduced signal correspondence in the central scan volume and for small lesions. MARIA® scanning was well tolerated. We believe that MARIA® signal corresponds to a malignant lesion in 47% of breast cancers examined. Our study, the largest to date for this type of technology, demonstrates successes and limitations of this MARIA® M6 version.

Reconfigurable Microwave Multi-Beamforming Based on Optical Switching and Distributing Network

Optical beamforming in microwave photonics is promising for supporting broadband wireless communications. However, the current optical beamforming lacks freedom because of the fixed connection between radio frequency (RF) signal and antenna elements (AEs). This manuscript tackles this challenge by proposing a dynamical optical beamforming architecture that reconfigures the antenna subarray for signal transmission depending on the number of signals to be transmitted. The proposed architecture employs an optical switching and distributing network (SDN) to realize a flexible connection between signals and AEs. An instance of the proposed architecture in photonic integrated circuits, which enables three working modes and transmits four RF signals through sixteen AEs, was presented and numerically simulated. The optical field distribution and beam pattern plots illustrated the operational principle and validated the feasibility of the proposed SDN architecture. Furthermore, the impact of the introduced architecture on the signal amplitude–phase consistency and the comparison of the proposed dynamic architecture and conventional fixe architectures are analyzed and discussed. The results indicate that the proposed architecture exhibits variable beamforming gain with lower hardware complexity.

Discoloration of RF antenna coil surface after long-term operation of J-PARC ion source

In J-PARC (Japan Proton Accelerator Research Complex) center, the continuous operation period of the Radio Frequency (RF) negative hydrogen ion (H−) source equipped with the internal RF antenna coil is extended step by step in these 6–7 years for the goal to supply stable beam during the entire period of J-PARC user operation each year. In 2022, the continuous ion source operation for 4,001 hours (5.5 months) was achieved with 60 mA H− beam current at the ion source exit, 25 Hz repetition, mainly 500 μs beam pulse width, and 25 kW RF power injection. As the lifetime of the RF ion source is mainly limited by the deterioration of the enamel coating on the RF antenna coil, a detailed evaluation of the antenna surface is required to ensure the feasibility of the further extension of the operation period. In the present study, surface discoloration on the RF antenna coil observed after 5 months of operation is investigated by the application of a digital microscope and SEM/EDS analyses. The EDS analyses show that depositions of the sputtered stainless steel elements and the injected cesium are the most possible candidates for impurities on the enamel coating. The dimension measurements of the RF antenna thickness before and after the long-term operation also support the assumption that the discoloration is due to the deposited elements and hence insulation of the RF antenna coil by enamel coating is maintained. Possible mechanisms leading to antenna deterioration starting from element depositions on the antenna coating are also discussed in the summary part of this manuscript.

Effect of a permanent-magnet-induced cusp field on a magnetic nozzle radio frequency plasma thruster

A cusp magnetic field is formed upstream of a radio frequency antenna by using a permanent magnet (PM) array in a radio frequency plasma source attached to a diffusion chamber, while an expanding magnetic field configuration downstream of the source is maintained by placing a solenoid near the source tube’s exit, resembling a magnetic nozzle plasma thruster. The PM array is composed of 16 neodymium magnets and is designed to be movable axially, providing a movable axial location of the cusp field. The source is operated at a frequency of 13.56 MHz and an rf power of up to 2.6 kW in low-pressure argon. A force exerted on a target plate located downstream of the source is assessed by a pendulum target technique, showing that the force is increased if the cusp field is closer to the radio frequency antenna. The result is consistent with the previously reported result for the cusp field configuration applied by two sets of solenoids, while the present configuration can reduce the consumed electricity for the upstream solenoid.

Investigation of Materials for Radio Frequency Antenna Plasma Facing Components

Investigation of Materials for Radio Frequency Antenna Plasma Facing Components

Bonding mechanism of laser joining of Poly-Ether-Ether-Ketone film which used for 5G antenna substrate to copper foil

The bonding of copper foil to Poly Ether Ether Ketone (PEEK) film has become a hotspot in research of the 5G RF (Radio Frequency) antenna substrate. In order to make the flexible copper clad laminates(FCCL) in the RF substrate thinner and more resistant to bending, there is an urgent need to replace the use of adhesive to join the copper foil to the PEEK film with a direct joining method. In this paper, a nanosecond laser was used to join the copper foil to the PEEK film effectively and the comprehensive property of joint was enhanced by the laser-textured grid on the surface of copper foil. The influence of textured grid on the adhesion work between copper foil and PEEK film was investigated. The interfacial morphology was observed and the result showed that molten PEEK completely filled the textured grid and formed a mechanical interlocking with copper. The complex reaction between Cu and PEEK was indicated by detecting the red-shift for the wave number of functional groups and the weak chemical bond between Cu and PEEK. Besides, the bonding mechanism was proved by density functional theory (DFT) calculation. The tensile shear strength of Cu/PEEK joint was significantly enhanced by laser texturing treatment, and the maximum force of joint with 0.4 mm-textured grid was increased by approximately 1.29 times compared to the untreated condition. This study proposes the use of nanosecond laser joining to replace the traditional use of adhesives to join copper foils to PEEK films.

153 Genomic Prediction and Genetic Parameters of Residual Feed Intake Computed Using Linear and Non-Linear Regression Methods in Broiler Chickens

Abstract Feed efficiency traits are important for reducing feeding costs while potentially decreasing the environmental impact of broiler production. This study aimed to compare the predictive ability of different genome-wide prediction models for residual feed intake (RFI) calculated with linear and non-linear regression techniques. We also evaluated the heritability of such RFI as well as their associations with body weight. Genotypes and phenotypes used in this study were recorded from 32,747 purebred broiler chickens of both sexes. The individual feed intake was monitored daily in floor-raised birds using a radio-frequency antenna system. RFI was computed as the residual term of total feed intake (FI) adjusted for the average metabolic weight (AMW), body weight gain (BWG), and sex. The following regression methods were used to compute RFI: multiple linear regression (MLR), generalized additive model using splines (GAM), support vector regression using a radial basis kernel (SVR), and two-hidden layer neural network (NN). The different RFI assessments were fitted jointly with body weight measured at the end of the feeding trial (FBW) using a two-trait mixed model. The effects of contemporary groups were fitted as fixed for both traits, whereas sex was also considered for FBW. RFI (computed with different regression techniques) was predicted using different genomic prediction models (BayesA, BayesB, BayesCπ, GBLUP, RKHS, and SVR). Genomic prediction accuracy (ACC) was assessed using a random forward validation scheme, in which data from previous generations were used for training the models while later generations were used to test predictions. The effect of the RFI computation method on ACC was tested using an unpaired Wilcoxon test. Sample variance observed for RFI ranged between 57,207.04 and 59,254.76, depending on the regression method used to compute it. Overall, the RFI sample variance was smaller for non-linear methods (NN, SVR, and GAM) compared with the linear model (MLR). The regression methods did not impact the genetic parameter estimates for RFI, which presented a heritability value around 0.32 ± 0.015 and genetic correlation with FBW ranging between 0.22 ± 0.04 and 0.25 ± 0.04. Prediction accuracy across genomic regression methods was slightly higher (P-value = 0.038) when RFI was computed with SVR (0.336 ± 0.023) compared with the MLR (0.329 ± 0.025), although this small difference would have little practical implications. No differences in terms of ACC were observed among the other regression methods used to compute RFI. Our preliminary results indicate that the regression technique used to compute RFI does not have major implications for this trait. Therefore, the MLR method is the preferred choice as it is simpler to implement, and it provides easy-to-interpret parameters.

152 Leveraging Rfid Technology to Investigate the Genetic Associations Between Feeding Behavior and Leg Health in Floor-Raised Broilers

Abstract Leg disorders (LD) pose serious welfare issues in broiler chickens. The objective of this study was to investigate the suitability of using feeding behavior (FB) traits as potential leg health indicators in floor-raised broilers. The data used were recorded from 95,711 pure-line chickens of both sexes. The individual FB was monitored continuously on a feeder visit basis with a radio-frequency antenna system. The visit-log data were clustered into daily observations for different FB traits and averaged for the 1st week period after the trial started. The FB traits were daily feed intake (DFI1), number of visits (NV1), time spent at the feeder (TSF1), visiting activity interval (VAI1), number of visited feeders (NVF1), and walked distance visiting feeders (WD1). The LD traits were tibial dyschondroplasia (TD), hock-burn (HB), footpad (FP), rotated legs (RO), bowed-in (BI), and bowed-out (BO) leg structure deformities. Multi-trait linear-threshold models were fitted using Bayesian inference for estimating (co)variance components. The heritability (h2) posterior averages and standard deviations (within parentheses) ranged between 0.09 (0.01) and 0.52 (0.03) for LD traits, and between 0.09 (0.01) and 0.47 (0.02) for FB traits. Genetic correlations (rg) between FB and LD traits ranged from null to weak. TD presented negative rg with NV1 (-0.13), TSF1 (-0.14), NVF1 (-0.11), and WD1 (-0.14), indicating that some alleles involved in broiler activity are favorably associated with a potential reduction in the risk of TD-caused bone lesions. Conversely, FP presented unfavorable rg with the same traits (ranging from 0.21 to 0.32), except for TSF1 (-0.08). When compared with the remaining FB traits, DFI1 generally presented the opposite relationships with TD and FP, with positive (0.16) and negative (-0.18) genetic correlations observed for the first and the latter, respectively. Angular and rotational deformities (RO, BI, and BO) did not present significant correlations with FB traits, apart from the weak correlation found between BO and TSF1 (0.11). General activity indicators such as NV1, NVF1, and WD1 could represent earlier selection criteria to reduce TD incidence, although the potential undesired selection response for FP must be further investigated.

Coherent manipulation of nuclear spins in the strong driving regime

Spin-based quantum information processing makes extensive use of spin-state manipulation. This ranges from dynamical decoupling of nuclear spins in quantum sensing experiments to applying logical gates on qubits in a quantum processor. Fast manipulation of spin states is highly desirable for accelerating experiments, enhancing sensitivity, and applying elaborate pulse sequences. Strong driving using intense radio-frequency (RF) fields can, therefore, facilitate fast manipulation and enable broadband excitation of spin species. In this work, we present an antenna for strong driving in quantum sensing experiments and theoretically address challenges of the strong driving regime. First, we designed and implemented a micron-scale planar spiral RF antenna capable of delivering intense fields to a sample. The planar antenna is tailored for quantum sensing experiments using the diamond’s nitrogen-vacancy (NV) center and should be applicable to other solid-state defects. The antenna has a broad bandwidth of 22 MHz, is compatible with scanning probes, and is suitable for cryogenic and ultrahigh vacuum conditions. We measure the magnetic field induced by the antenna and estimate a field-to-current ratio of G/A, representing a six-fold increase in efficiency compared to the state-of-the-art, crucial for cryogenic experiments. We demonstrate the antenna by driving Rabi oscillations in 1H spins of an organic sample on the diamond surface and measure 1H Rabi frequencies of over 500 kHz, i.e. -pulses shorter than 1 —an order of magnitude faster than previously reported in NV-based nuclear magnetic resonance (NMR). Finally, we discuss the implications of driving spins with a field tilted from the transverse plane in a regime where the driving amplitude is comparable to the spin-state splitting, such that the rotating wave approximation does not describe the dynamics well. We present a simple recipe to optimize pulse fidelity in this regime based on a phase and offset-shifted sine drive, which may be optimized in situ without numerical optimization procedures or precise modeling of the experiment. We consider this approach in a range of driving amplitudes and show that it is particularly efficient in the case of a tilted driving field. The results presented here constitute a foundation for implementing fast nuclear spin control in various systems.

Resonance cones in cold plasma: Origin, singularities, and power flow

In magnetized tenuous plasma, typical at the plasma edge of fusion devices, a nearly electrostatic wave mode with relatively enhanced electric field can propagate along a specific angle with the magnetic field. For this characteristic, it is known as a “resonance cone.” For instance, these waves can be excited by radio frequency antennas in the ion-cyclotron and lower-hybrid range of frequencies. We consider the resonance cones emitted by idealized spatially extended sources. In 2D, we use a novel geometric construction which generalizes the d'Alembert solution to curved boundaries/moving sources, and show, for the first time, that singular electric fields arise under these conditions, thereby bringing the resonance cones in line with the other resonances of the cold plasma theory. Still in 2D, we give an expression for the amount of power radiated by resonance cones in terms of surface quantities on the source, which is finite despite the singular electric field. We generalize the conclusions regarding the presence and location of singular electric fields to the 3D electromagnetic case.