Quartz Crystal Microbalance Chip Research Articles

Synergie between molecular imprinted polymer based on solid-phase extraction and quartz crystal microbalance technique for 8-OHdG sensing

Recently, the 8-hydroxy-2′-deoxyguanosine (8-OHdG) has been used as a marker to determine the oxidative stress. There is no any cheap and easy determination method based on chips and sensor systems for the determination of 8-OHdG. In this study, we have proposed imprinting methods for 8-OHdG recognition and determination using methacryloylamidohistidine-platinum(II) [MAH-Pt(II)] as a new metal-chelating monomer. The study includes the solid-phase extraction (SPE) of blood sample by a new 8-OHdG imprinted sorbent and the measurement of binding interaction of 8-OHdG imprinted quartz crystal microbalance (QCM) sensor via ligand interaction. 8-OHdG imprinted sorbent has prepared by bulk polymerization of MAH-Pt(II) and N- N′-methylenebisacrylamide. 8-OHdG imprinted sensor has prepared on a QCM chip coating the thiol pretreated Au electrode. At the end of these steps, a thin molecular imprinted polymer (MIP) film for the detection of 8-OHdG has developed and analytical performance of QCM sensor which has prepared using MIP was investigated. The affinity constant ( K a) for 8-OHdG using MAH-Pt-based thin film has determined by using the Scatchard method. The average percentage recovery of 8-OHdG from plasma samples was found as 80% by using of 8-OHdG imprinted SPE material. At the last step, 8-OHdG level in several blood plasma has been determined by this improved QCM sensor. The obtained results confirmed that the 8-OHdG level in cancer patient's blood was significantly higher than in general subjects.

Recognition of conformational changes in beta-lactoglobulin by molecularly imprinted thin films.

Pathogenesis in protein conformational diseases is initiated by changes in protein secondary structure. This molecular restructuring presents an opportunity for novel shape-based detection approaches, as protein molecular weight and chemistry are otherwise unaltered. Here we apply molecular imprinting to discriminate between distinct conformations of the model protein beta-lactoglobulin (BLG). Thermal- and fluoro-alcohol-induced BLG isoforms were imprinted in thin films of 3-aminophenylboronic acid on quartz crystal microbalance chips. Enhanced rebinding of the template isoform was observed in all cases when compared to the binding of nontemplate isoforms over the concentration range of 1-100 microg mL(-1). Furthermore, it was observed that the greater the changes in the secondary structure of the template protein the lower the binding of native BLG challenges to the imprint, suggesting a strong steric influence in the recognition system. This feasibility study is a first demonstration of molecular imprints for recognition of distinct conformations of the same protein.

Cytochrome c Self-Assembly on Alkanethiol Monolayer Electrodes as Characterized by AFM, IR, QCM, and Direct Electrochemistry

With the advantage of carbodiimide coupling chemistry, horse heart cytochrome c (cyt c) has been covalently immobilized onto self-assembled monolayers (SAMs) from 11-mercaptoundecanoic acid (MUDA) developed on single-crystal or polycrystalline gold substrate surfaces. The cyt c immobilized substrates thus prepared have been characterized by atomic force microscopy (AFM); we have succeeded in obtaining surface topographical images down to single-protein resolution. AFM imaging has also shown densely packed, uniform protein monolayer formation that is highly suggestive of self-assembly of cyt c molecules on MUDA SAMs. Covalent attachment of cyt c has been further evidenced by reflection-absorption FT-IR as well as microgravimetric analysis using a quartz crystal microbalance (QCM). In the latter, the specific MUDA and cyt c surface concentrations were determined to be 0.86 +/- 0.11 nmol cm-2 (n = 5) and 28 +/- 12 pmol cm-2 (n = 5), both of which agree fairly well with their theoretical counterparts. The obtained QCM chips having the cyt c/MUDA/Au interfacial structure were found to be capable of the direct electrochemistry of the surface-attached cyt c molecules. Cyclic voltammetric measurements on the chips gave particular redox waves showing characteristics of surface process. The electroactive protein surface concentration was determined to be 7.2 +/- 4.8 pmol cm-2 (n = 6); it was almost consistent with values found in literature, while it was limited to 26% in magnitude for the QCM data. This was deemed to have arisen from the orientation variation of the surface-confined cyt c molecules and is discussed briefly.

Artificial Receptors in Serologic Tests for the Early Diagnosis of Dengue Virus Infection

Because of the range and nonspecificity of clinical presentations of dengue virus infections, we felt there was a need to create diagnostic tests. We used artificial receptors for the virus to develop serologic assays to detect dengue virus infection. We coated a quartz crystal microbalance (QCM) with molecularly imprinted polymers specific for nonstructural protein 1 of flavivirus. These artificial receptors were specifically created on a QCM chip by polymerization of monomers and were cross-linked in the presence of the epitope site of nonstructural protein 1. We tested serum samples from patients with confirmed cases of dengue reported to the Center for Disease Control in Taipei. Samples were diluted 100-fold; no other sample pretreatment was used. The QCM response was compared with results of monoclonal ELISA. QCM signals were >15 Hz in 18 of 21 (86%) of dengue samples and in 0 of 16 control samples. The correlation (r2) of the QCM response and the ELISA result was 0.73. Within-run and run-to-run imprecisions (CV) were 4%-28% and 10%-32%, respectively. The described assay offers a serologic technique for diagnosis of early viremia. The results illustrate the potential of well-organized polymers on the highly sensitive sensor system for diagnostic and biotechnological applications.

Recognition of Dengue Virus Protein Using Epitope-Mediated Molecularly Imprinted Film

Molecularly imprinted film was fabricated in the presence of a pentadecapeptide onto a quartz crystal microbalance (QCM) chip. This 15-mer peptide has been known as the linear epitope of the dengue virus NS1 protein. Imprinting resulted in an increased polymer affinity toward the corresponding templates but also to the virus protein. Direct detection of the dengue virus protein was achieved quantitatively. The QCM chip response to the NS1 protein was obtained using epitope-mediated imprinting demonstrating a comparable frequency shift in chips immobilized with monoclonal antibodies. The binding effect was further enhanced and confirmed using a monoclonal antibody to form a sandwich with the MIP-NS1 protein complex on the chip. No pretreatment was required.

Adsorption/Desorption of Mono- and Diblock Copolymers on Surfaces Using Specific Hydrogen Bonding Interactions

Diblock copolymers containing recognition units designed to participate in specific three-point hydrogen bonding were adsorbed onto modified gold surfaces. Self-assembled monolayers (SAMs) containing complementary recognition units were used to direct the adsorption process. The polymer-modified surfaces obtained were characterized using X-ray photoelectron spectroscopy, water contact angle, and ellipsometry. The role of individual block lengths on the adsorption process was followed by observing frequency changes of thymine-SAM-modified quartz crystal microbalance chips during adsorption of diamidopyridine-functionalized polymers from a nonpolar solvent. The renewable nature of these recognition unit functionalized surfaces was demonstrated by reversible binding of polymers. Adsorption onto fresh surfaces, followed by desorption and subsequent readsorption of monoblock and diblock copolymers was also investigated.

Development of a direct-binding chloramphenicol sensor based on thiol or sulfide mediated self-assembled antibody monolayers

A batch-type antibody-immobilized quartz crystal microbalance (QCM) system for detecting chloramphenicol (CAP) was developed. To bind an anti-CAP antibody onto the gold electrode surface of piezoelectric crystals, self-assembled monolayers (SAMs) of different thiols or sulfides were formed by a chemisorption procedure. Then, the anti-CAP antibody was covalently linked to the pre-formed monolayers by an activation procedure using 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride and N-hydroxysulfosuccinimide. The antibody-immobilized QCM chip thus prepared was installed in a well holder and was measured for sensor response. Compared with the bare QCM chip and the QCM chip only coated with 3-mercaptopropionic acid (MPA), the antibody-immobilized sensor showed greatly enhanced frequency shifts by 10–50-fold after CAP injection. In this case, CAP detection which was indicated by steady-state resonant frequency shift was accomplished within 10 min. When CAP solution was injected into the reaction cell in 50 mM concentration, the frequency shifts obtained were, respectively, 530 and 505 Hz in case of thiosalicylic acid and MPA immobilization. Repeated use of the sensor chips up to eight times was possible after 1 min regeneration with 0.1 M NaOH. This system demonstrated a potential application of thiol or sulfide mediated SAMs as the pre-coatings of a real-time detection on CAP in solution.

A versatile planar QCM-based sensor design for nonlabeling biomolecule detection.

Despite high theoretical sensitivity, low-cost manufacture, and compactness potentially amenable to lab-on-a-chip use, practical hurdles have stymied the application of the quartz crystal microbalance (QCM) for aqueous applications such as detection of biomolecular interactions. The chief difficulty lies in achieving a sufficiently stable resonance signal in the presence of even minute fluctuations in hydrostatic pressure. In this work, we present a novel versatile planar sensor chip design (QCM chip) for a microliter-scale on-line biosensor. By sealing the quartz resonator along its edges to a flat, solid support, we provide uniform support for the crystal face not exposed to solvent, greatly decreasing deformation of the crystal resonator under hydrostatic pressure. Furthermore, this cassette design obviates the need for direct handling when exchanging the delicate quartz crystal in the flow cell. A prototype 27-MHz sensor signal exhibited very low noise over a range of flow rates up to 100 microL/min. In contrast, signals obtained from a conventional QCM sensor employing an O-ring-based holder were less stable and deteriorated even further with increasing flow rate. Additional control designs with intermediate amounts of unsupported undersurface yielded intermediate levels of stability, consistent with the interpretation that deformation of the crystal resonator under fluctuating hydraulic pressure is the chief source of noise. As a practical demonstration of the design's high effective sensitivity, we readily detected interaction between myoglobin and surface-bound antibody.