Qualified Rate Research Articles

Multi-pass deep-drawing process and mould design for thin-walled hollow cylindrical parts

Thin-walled hollow cylindrical parts are widely employed in various industries, including automobiles, ships, and aviation, due to their increased demand and the escalating quality requirements for their formation. The production of these parts primarily relies on a multi-stage deep drawing process. However, during the deep drawing process, the gradual reduction in the side wall thickness creates a susceptible area at the bottom rounded transition, where local over-thinning may occur, thereby increasing the risk of cracking. Furthermore, the deep-drawing process becomes more intricate for thin-walled hollow cylindrical parts with a large height-to-diameter ratio, amplifying the likelihood of defects during actual production. This paper combines CAE simulation and empirical design to comprehensively investigate and analyze the multi-stage deep drawing process and mold design for thin-walled hollow cylindrical parts. The aim is to optimize the deep-drawing process and mold parameters, enhance the products qualification rate, and provide valuable guidance for the practical production of relevant enterprises.

Two-Year Clinical Outcomes of the PAUL Glaucoma Implant in White Patients With Refractory Glaucoma.

This prospectively collected case series of 56 eyes having PAUL glaucoma implant (PGI) surgery is the first to demonstrate its medium-term safety and effectiveness in what is essentially an exclusively Caucasian population. To report 2-year outcomes from a single-center cohort undergoing PGI surgery. Prospectively collected data on patients undergoing PGI surgery at the University Eye Hospital Bonn, Germany, from April 2021 to September 2021. Of 53 patients, 56 eyes were included. Complete and qualified success rates (95% CI) were 52% (37-66) and 89% (80-96) for criterion A ( intraocular pressure [IOP]≤21mm Hg), 48% (36-61) and 79% (67-88) for criterion B (IOP≤18mm Hg), 45% (32-57) and 64% (52-77%) for criterion C (IOP≤15mm Hg) and 27% (16-40) and 38% (25-50) for criterion D (IOP≤12mm Hg), respectively. Mean IOP decreased from 25.43mm Hg (7-48mm Hg) to 11.25mm Hg (3-24mm Hg) (reduction of 50%) after 24 months with a reduction of IOP-lowering agents from 3.50 (1-5) to 0.46 (0-3). One eye needed an injection of viscoelastic due to significant hypotony with AC shallowing; 3 eyes received a Descemet membrane endothelial keratoplasty because of persistent corneal decompensation; 9 eyes developed tube exposure which required conjunctival revision with additional pericardial patch graft, with 5 of these eyes eventually needing tube explantation. An intraluminal prolene stent was removed in 24 eyes (42.9%) after a mean time period of 5.67 months (2-15m). Mean IOP before removal was 21.4mm Hg (12-40mm Hg) and decreased to 11.15mm Hg (6-20mm Hg). PGI surgery is an effective procedure for reducing IOP and pressure-lowering therapy. The use of an intraluminal prolene stent impedes hypotony in the early postoperative phase and enables further noninvasive IOP lowering during the postoperative course.

Design and control of a side dense transplanting machine for sweet potato seedlings on mulch film

At present, China is the leading country in sweet potato cultivation worldwide. However, there are still several problems such as high labor intensity, low efficiency of manual transplanting, and lack of machinery for side transplanting for sweet potato seedlings on mulch film. Therefore, a side dense transplanting machine for sweet potato seedlings on mulch film is designed, using a multi-row side transplanting method. It is mainly composed of a transplanting device, a seedling conveying device, a traveling device, and a control system. Based on the agronomic requirements for sweet potato transplanting, the study focuses on the structure and working principle of the complete machine. It involves the detailed structural design and motion analysis of the crank-rocker and cam of the transplanting device. Based on the sweet potato seedlings transportation plan, parameters such as the vertical height of the seedling conveying device, the size of the support frame, and the relative relationship between position of the transplanting device are determined. To ensure the smooth transplantation of sweet potato seedlings, the motor parameters required for each device are calculated and determined. An Arduino control system is developed to manage the coordinated movement of each device. Positioning components are integrated to ensure accurate coordination between the transplanting device and the seedling conveying device. This setup enables the seedling claws to pick sweet potato seedlings and perform the side transplanting on the mulch film. Field test results show the missed rate of seedlings, the qualified rate of transplanting and the qualified rate of transplanting depth are 4.13 %, 91.62 % and 93.86 % respectively. The transplant spacing coefficient of variation and the average spacing between seedlings are 1.90 and 177.06 mm respectively. All indicators of the transplanting machine meet the agronomic requirements for side dense transplanting for sweet potato seedlings on mulch film. The transplanting machine is integrated with sweet potato seedling transplanting agronomy, achieving mechanized transplanting of sweet potato seedlings, reducing labor intensity, and promoting the quality and efficiency of sweet potato production. This research provides a reference for the development of sweet potato seedlings transplanting equipment.

Long-term efficacy and safety of XEN-45 gel stent implantation in patients with normal-tension glaucoma

BackgroundMinimally invasive bleb surgery using the XEN-45 gel stent has not been established for the treatment of normal-tension glaucoma (NTG). The main objective of this study was to evaluate the long-term treatment efficacy and safety of XEN-45 in eyes with uncontrolled NTG.MethodsA retrospective analysis of patients with NTG who underwent XEN-45 gel stent implantation at university hospital Tuebingen between 2016 and 2021. The primary outcome measure was surgical success after three years defined as lowering of intraocular pressure (IOP) of ≥ 20%, with target IOP between 6 and 15 mmHg. Success was complete without and qualified irrespective of topical antiglaucoma medication use. The need for further glaucoma surgery, except for needling, was regarded as a failure. The secondary outcome measures included changes in mean IOP, number of antiglaucoma medications, and needling and complication rates.ResultsTwenty-eight eyes from 23 patients were included in the final analysis. Complete and qualified success rates were 56.5% and 75% after three years, respectively. Mean postoperative IOP ± standard deviation decreased significantly after three years from 19.3 ± 2.0 mmHg at baseline to 13.7 ± 4.2 mmHg (n = 22; p < 0.0001). The median number of antiglaucoma medications decreased from 2 (range 0–4) to 0 after three years (range 0–3; p < 0.0001). Sixteen eyes (57%) required a median of 1 (range 1–3) needling procedures. One eye required further glaucoma surgery. No sight-threatening complications were observed.ConclusionThe XEN-45 stent is effective and safe for the long-term treatment of NTG. However, needling was frequently required to improve outcomes.

Evaluation of Intrascleral Lakes after Phaco-Viscocanalostomy using Anterior Segment Optical Coherence Tomography.

This study aimed to investigate the results of combined phacoemulsification and viscocanalostomy (phaco-VC) in a six-month follow-up and its relationship with intrascleral lake (IL) using anterior segment optical coherence tomography (AS-OCT) in patients with primary open-angle glaucoma (POAG). In total, 36 eyes with POAG eligible for phaco-VC were enrolled in this prospective observational study. All patients underwent AS-OCT evaluation and ophthalmologic examination including Goldman tonometry, cup-disc ratio assessment, best corrected visual acuity (BCVA) measurement, and antiglaucoma medication(s) prior to surgery and one, three, and six months after the surgery. The width, length, area, and circumference of the ILs were evaluated using AS-OCT at each follow-up. A total of 36 eyes of 34 patients with POAG were investigated in this study. According to the results, the mean age of the patients was 70.09 8.73 years, and the majority of the cases were male (n = 23; 63.9%). The mean preoperative intraocular pressure (IOP) was 20.11 7.22 mmHg on 2.47 1.1 medications, and the mean postoperative IOP reduced to 11.11 2.58 mmHg on 0.11 medications, which was statistically significant (P 0.001). ILs were detectable in all cases which resulted in a 100% qualified success rate. The reduction in the width, area, and circumference of the IL was significant during the six-month follow-up. The relationship between IOP changes and IL parameters on AS-OCT was not significant. This study evaluated the associations between IL changes and IOP reduction after phaco-VC. A six-month follow-up showed a notable reduction in the IL, but unexpectedly, IOP control did not decline. A reduction in IL diameter, when there is sufficient IOP control, indicates that there may be various IOP lowering mechanisms through VC other than the IL diameters. Further evaluation of VC focusing on long-term changes in IL and Schlemm's canal diameter is necessary to explain the precise mechanisms of lowering the IOP.

Characteristic analysis of mold level fluctuation during continuous casting of Ti-bearing IF steel

Mold level fluctuation has always been one of the key factors in slab quality control. Abnormal fluctuations can easily cause slag entrainment and form surface defects of hot-rolled and cold-rolled steel sheets, thus reducing the product qualification rate. In this study, mold level fluctuation data was collected during Ti-bearing Interstitial Free (IF) steel in a stable state for a complete casting sequence in a certain factory. The mold level fluctuation is analyzed using the discrete wavelet transform (DWT) method, and its characteristic values are classified based on frequency. Combined with the corresponding process parameters, the causes were traced during abnormal fluctuation characteristic values. It was found that the formation of abnormal mold level fluctuation mainly comes from two aspects. On the one hand, there are random fluctuations in the low-frequency band, and on the other, there are clustered fluctuations in the relatively high-frequency band. There is always a rising trend in mold liquid levels when there are random abnormal fluctuations in the low-frequency band. There is a delay of approximately 0.1412 s in the feedback of the stopper rod to the mold level fluctuation. The major causes of the low-frequency random fluctuations include variations in the tundish weight, casting speed, and mold width, and the clogs peeling. The clogging of the side hole at the submerged entry nozzle (SEN) is the primary cause of abnormal clustered fluctuations in the high-frequency band. These are certain relationships with clogging, whether it is high-frequency clustered or low-frequency random abnormal fluctuations. Without a doubt, this is a crucial link that limits the slab quality.

Design and experiment of impeller seed guide device for rice internal suction hole direct seeding device

Multi-grain hole-forming sowing and uniform hole spacing are important agronomic requirements for precise hole-direct seeding of rice.This paper designs a kind of impeller type seed guiding device. The main structural parameters of the impeller seed guide device were analyzed by constructing the kinematics model of the rice seed in the impeller seed guide process. The experiment analysis were carried out with the long-grain rice variety Chuangliangyou 4418 as the seeding object. The optimal structural parameter combination of seeding-guiding device was determined as inner impeller radius 56 mm, blade offset angle 11° and seeding angle 36°. On this basis, the seeding performance test of different seed guiding devices of internal suction seed-metering device was carried out by using rice seeds with different external dimensions. The test results show that the impeller has better cavitation and hole spacing uniformity than the seed guide tube. The average hole diameter is not higher than 21.7 mm, the qualified rate of hole diameter is not lower than 96.1%, and the coefficient of variation of hole spacing is not higher than 10.1%. Compared with the seed guide tube, which is increased by 32%, 16% and 34% respectively, and the average hole distance is about 200 mm in theory.

Efectividad de la válvula de Ahmed® implantada vía pars plana en pacientes con glaucoma refractario

PurposeTo evaluate the success rate and complications of the Ahmed® FP7 valve implanted via Pars Plana in a group of vitrectomized patients with refractory glaucoma and anterior segment abnormalities from January 2018 to June 2023. MethodsQuasi-experimental, prospective study. Eleven eyes with refractory glaucoma were included. Participants underwent a comprehensive ophthalmic examination, including assessment of intraocular pressure (IOP) reduction, visual acuity, characterization of glaucoma type, and number of antiglaucoma medications. ResultsThe mean baseline IOP was 37.3±11mmHg, which decreased to 13.5±3.0mmHg after one year. The qualified success rate was 63.7%, while the complete success rate was 36.3%. The most common diagnosis was neovascular glaucoma in 36.4% of cases. The most frequent postoperative complications were choroidal detachment and hypotony. ConclusionsOur data suggest that implantation of the Ahmed FP7 valve via pars plana is an effective and safe option for patients with refractory secondary glaucoma.

An Integrated Potato-Planting Machine with Full-Film Mulching and Ridged Row Soil Covering

This paper presents the design of an integrated potato-planting machine capable of full-film covering, creating micro-ditches on ridges, and covering seed rows with soil. The machine addresses the challenges of traditional methods, allowing for mechanized planting with complete film coverage and individual seed row soil covering. The key components of the prototype were analyzed and designed. This includes the seeding system, the pointed wing-shaped trencher for creating micro-ditches, and the straddling film-mulching device. Additionally, the operating mechanism of these core components was analyzed. Field trials demonstrated an 85% success rate for seed depth placement under the film. The machine also achieved a 90% qualified index for seed potato spacing, with a 6% repetitive seeding rate and a 3% missed seeding rate. Furthermore, the qualified rate for covered soil width on seed rows was 94%, and the qualified rate for covered soil thickness was 93%. The adjacent row spacing achieved an 88% success rate. The degree of mechanical damage to the exposed surface of the mulch film was minimal, at only 30.2 mm2/m2. These results meet all the national and industry standards. The successful field trials confirm the effectiveness of the machine in performing integrated fertilization, sowing, ridging, full-film covering, and seed row soil covering. Compared to traditional methods, this machine significantly reduces labor intensity for farmers and enhances the economic value of potato planting.

Application of metal cushion block combined with Jumbo cup in reconstruction of acetabular bone defect in revision of artificial hip joint

To investigate the application effect and imaging changes of metal cushion block combined with Jumbo cup in the reconstruction of acetabular bone defect after revision of artificial hip joint. Retrospective analysis was made on the clinical data of 83 patients who underwent revision acetabular bone defect reconstruction of the artificial hip joint in our hospital from September 2019 to October 2021. They were divided into group A and group B according to different surgical methods. There were 42 patients in group A, including 26 males and 16 females, aged from 44 to 72 years old with an average of (60.57±4.62) years, who underwent revision with metal cushion block and Jumbo cup. There were 41 patients in group B, including 22 males and 19 females, aged from 42 to 71 years old with an average of (58.74±4.25) years, who underwent revision with metal cushion block and bone cement mortar cup. The operation related indexes, Harris hip function score and visual analogue scale (VAS) of pain before operation, 1 month and 12 month after operation were compared between two groups. The results of X-ray imaging examination (hip rotation center height, acetabular abduction angle, femoral eccentricity and imaging standard qualification rate) before and 12 month after operation were evaluated, and the incidence of complications was compared between two groups. There was no significant difference in operation time, intraoperative bleeding volume and postoperative drainage volume between two groups (P>0.05). Both groups were followed up for 12 to 36 months with an average of (25.36±3.59) months. The scores of pain, function, deformity and Harris' total score in the two groups at 1 month after operation were higher than those before operation (P<0.05), and the scores of pain, function, deformity, joint activity and Harris' total score in two groups at 1 year after operation were higher than those before operation and 1 month after operation (P<0.05), and the above scores in group A were higher than those in group B at 1 year after operation (P<0.05). The VAS of two groups decreased successively at 1 month and 1 year after operation (P<0.05), but there was no significant difference in both groups at each time point (P>0.05). The femoral eccentricity increased in both groups at 1 year after operation (P<0.05), and group A was higher than group B (P<0.05). The height of rotation center and acetabular abduction angle decreased in both groups at 1 year after operation (P<0.05), and the height of rotation center in group A was lower than that in group B (P<0.05), but there was no significant difference in acetabular abduction angle between two groups (P>0.05). The imaging qualification rate of group A was higher than that of group B (P<0.05). There was no significant difference in the incidence of adverse reactions between two groups (P>0.05). Metal cushion block combined with Jumbo cup in the treatment of acetabular bone defects can provide the hip joint function, and restore the hip joint rotation center, femoral eccentricity and acetabular abduction angle, with obvious clinical effect.

Impact of Peripheral Anterior Synechiae on the Outcome of Combined Phacoemulsification, Goniosynechialysis, and Goniotomy for Primary Angle Closure Glaucoma and Cataract: A Multicenter Observational Study.

The combination of phacoemulsification, goniosynechialysis and goniotomy is an effective treatment for primary angle closure glaucoma patients with cataract, and this is not linked to the extent of preoperative peripheral anterior synechiae. To evaluate the impact of the extent of peripheral anterior synechiae (PAS) on the effectiveness and safety of combined phacoemulsification (PEI), goniosynechialysis (GSL), and goniotomy (GT) in eyes with primary angle closure glaucoma (PACG) and cataract. This study included patients diagnosed with PACG and cataracts who underwent combined PEI and 120 degrees GSL plus GT (PEI+GSL+GT) between April 2020 and October 2022 at 10 ophthalmic institutes. Eligible patients were divided into 3 groups based on the extent of PAS: 180°≤PAS<270°, 270°≤PAS<360°, and PAS=360°. Data on intraocular pressure (IOP), the number of ocular hypotensive medications, and complications were collected and compared. The study defined complete success as postoperative IOP within the 6-18mm Hg range and a 20% reduction from baseline without the use of topical medications. Qualified success was defined in the same way as complete success, but it allowed for the use of ocular hypotensive medications. Three hundred four eyes of 283 patients were included. The mean follow-up was 12.50±1.24 months. All groups experienced a significant reduction in IOP after the surgery ( P <0.05). There were no significant differences in final IOP, number of medications, and cumulative complete and qualified success rates among the 3 groups ( P >0.05). The groups with 270°≤PAS<360°had a higher frequency of hyphema compared with 180°≤PAS<270° ( P = 0.044). PEI+GSL+GT has proven to be an effective treatment for PACG with cataracts over a 1 year period. However, the outcome was not correlated with the preoperative extent of PAS.

Randomised clinical trial: Design of the SYNERGY-NASH phase 2b trial to evaluate tirzepatide as a treatment for metabolic dysfunction-associated steatohepatitis and modification of screening strategy to reduce screen failures.

The use of histological inclusion criteria for clinical trials of at-risk metabolic dysfunction-associated steatohepatitis (MASH) is often associated with high screen failure rates. To describe the design of a trial investigating tirzepatide treatment of MASH and to examine the effect of new inclusion criteria incorporating the use of the FibroScan-AST (FAST) score on the proportion of patients meeting histological criteria. SYNERGY-NASH is a Phase 2b, multicentre, randomised, double-blinded, placebo-controlled trial in patients with biopsy-confirmed MASH, F2-F3 fibrosis and NAFLD Activity Score ≥4. New inclusion criteria (FAST score >0.35 and an increase in AST inclusion criterion from >20 to >23 U/L) were adopted during the trial, allowing us to examine its impact on the qualification rate. 1583 participants were screened, 651 participants proceeded to liver biopsy and 190 participants were randomised with an overall screen fail rate of 87%. Following the protocol amendment, the overall qualification rate for per-protocol biopsies was minimally changed from 27.5% to 28.9% with considerable variation among different investigator medical speciality types: endocrinology: from 37.5% to 39.3%; gastroenterology/hepatology: from 26.0% to 23.3%; other specialities: from 21.3% to 29.7%. At 29 sites that performed per-protocol biopsies before and after the amendment, qualification rates changed as follows: all: 26.1% to 29.1%; endocrinology: from 35.0% to 40.9%; gastroenterology/hepatology: 25.6% to 20.0%; other specialities: from 16.1% to 27.8%. For at-risk MASH trials based on liver histology, the implementation of inclusion criteria with the proposed FAST score and AST cut-offs in this trial was most effective at non-specialist sites.

Cross-sectional study on the epidemiological investigation ability of professional staff from Centers for Disease Control and Prevention in Guizhou Province.

This study aims to evaluate the qualifications and identify skill enhancement areas for epidemiological investigators in Centers for Disease Control and Prevention (CDCs) in Guizhou's, informing future training and policy initiatives to strengthen public health responses. A cross-sectional survey was conducted in August 2022, and an online, self-designed questionnaire on the Epidemiological Dynamic Data Collection platform was administered to evaluate the professional staff in CDCs. The responses were scored and presented using descriptive statistical methods, and the factors influencing the total score were analyzed by one-way ANOVA and linear regression. A total of 1321 questionnaires were collected, yielding an average score of 14.86±3.49 and a qualification rate of 29.9%. The scoring rate of ability of individual protection and coordination in epidemic control was high (87.25%). Meanwhile, improvements in further training were needed in areas such as data analysis ability (23.67%), knowledge of site disinfection (40.40%), and epidemiological investigation skills (42.50%). No significant difference was observed between the scores of city and county CDCs, (t = 1.071, p =0.284). The effects of gender and age could be disregarded, and the experience in epidemiological work and training (including investigation on COVID-19 cases and contacts), educational background, and professional title partially explained the survey outcome (R Square of the linear regression model was 0.351). The survey indicated the need for additional well-trained epidemiologic investigators in Guizhou. Specified training was effective in improving epidemiologic investigation, and enhancement in data analysis ability and knowledge of field disinfection are recommended in professional staff cultivation.

Sintering Technology of Cemented Carbide Cutting Tool Based on Digital-Twin

Cutting tool sintering process is one of the key links in cutting tool manufacturing process. Various physical quantities change with time during cutting tool sintering. As the sintering quality of cutting tool is directly affected by these changes, it is very difficult to predict and control the sintering quality of cutting tool. Due to the complex structure of sintering equipment, it is difficult to obtain high quality and sufficient data to train the sintering quality prediction model. In this paper, the real-time condition monitoring, prediction and control of carbide cutting tool during sintering process are studied. In this study, a digital-twin model of cemented carbide cutting tool sintering furnace was established. Based on this model, the change of heat distribution characteristics in sintering furnace during sintering process is precisely described. Firstly, the paper establishes the mapping architecture of cutting tool sintering digital-twin system. Based on this architecture, a digital-twin model of heat radiation in sintering furnace is established in this paper. Based on the temperature and pressure data in the sintering furnace, the radiation heat transfer in the furnace is analyzed in order to determine the temperature change of the cutting tool sintering position. In this paper, the relationship between the temperature change of cutting tool sintering position and cutting tool grain size is studied. Based on this relationship, a rolling data-driven digital-twin prediction model for cutting tool sintering has been constructed. In this paper, cutting tool sintering temperature control driven by digital-twin system is realized based on a fuzzy control model. The validity of the digital-twin system is verified by a series of comparative experiments. The test results show that the temperature error of the system control is less than ±1 °C. It effectively improves the qualified rate of cutting tool sintering.

A comparison of deep sclerectomy outcomes in eyes with pseudoexfoliation versus primary open angle glaucoma

PurposeTo compare outcomes of augmented deep sclerectomy surgery (DS) with mitomycin C.(MMC) between pseudoexfoliative glaucoma (PEXG) and primary open angle.glaucoma (POAG) patients.. DesignRetrospective cohort study MethodsRetrospective review of patients undergoing DS surgery at the University Eye Hospital Bonn, Germany, from 04/2021 to 09/2022. We performed a matched-pair analysis.between eyes with PEXG (group 1, n = 45) and eyes with POAG (group 2, n = 45). Results90 eyes of 85 patients were included. Complete and qualified success rates for Groups.1 and 2 at one year were 55.6 % and 86.7 % (p = 0.002) and 91.1 % and 93.3 % (p = 0.78).for ≤21 mmHg, and 55.6 % and 86.7 % (p = 0.002) and 88.9 % and 93.3 % (p = 0.53) for.≤18 mmHg respectively..Mean preoperative IOP decreased from 21.11 mmHg in group 1 and 19.64 mmHg in.group 2 (p = 0.31) to 13.64 mmHg and 11.42 mmHg after surgery, respectively, whilst it.was significantly lower in eyes with POAG (p = 0.01). The number of pressure-lowering.drops was also significantly lower in eyes with POAG after 12 months (PEXG: 0.58;.POAG: 0.18; p = 0.01). Eyes with PEXG had a significantly higher rate of Nd:YAG laser.goniopuncture (PEXG: 64.4 %, POAG: 40 %, p = 0.02)..Postoperative complications occurred in 6 eyes (6.7 %) with no vision-threatening.sequelae in either group.There were no significant differences between complication.rates in the two groups (p = 0.18) ConclusionsDS is a safe and effective procedure for lowering IOP in eyes with both POAG and PEXG, with lower overall IOP levels being achieved in eyes with POAG. Significantly more postoperative laser goniopunctures were needed in eyes with PEXG.

Clinical study on the efficacy and safety of glaucoma drainage implants in the treatment of different types of glaucoma

Objective: To evaluate the efficacy and safety of glaucoma drainage implants(XEN-45 Gel Stent) for glaucoma treatment. Methods: A prospective study was conducted to continuously collect the clinical data of patients who were diagnosed with glaucoma and underwent XEN-45 Gel Stent implantation in the Ophthalmology Department of Peking University People's Hospital from January 2022 to August 2023. The visual acuity, intraocular pressure, number of glaucoma medications, and success rate of the patients were analyzed before and after surgery at 1 day, 1 week, 1 month, 3 months, 6 months, 12 months, and 18 months. The differences in intraocular pressure and number of glaucoma medications among primary open-angle glaucoma, primary angle closure glaucoma, secondary glaucoma, and different implantation methods of XEN-45 Gel Stent among patients with primary open-angle glaucoma were compared. The intraoperative and postoperative complications were observed, and the risk factors for needling and surgical complete success were analyzed. Results: A total of 48 eyes from 48 patients were included in this study, comprising 27 males and 21 females, with a mean age of (54.4±18.0) years and the disease duration was 36.0(7.3, 81.0) months.There were 28 cases of primary open-angle glaucoma, 4 cases of primary angle closure glaucoma, and 16 cases of secondary glaucoma.The follow-up period was 8.0 (3.0, 12.0) months. At 12 months after surgery, the intraocular pressure decreased from 20.5 (17.0, 26.0) mmHg to (13.5±3.3) mmHg (P<0.05), and the number of glaucoma medications decreased from 3.0 (3.0, 4.0) to 0.0 (0.0, 0.0) (P<0.05). The complete success rate and qualified success rate were 73.9% (17/23) and 91.3% (21/23), respectively. The most common postoperative complications were shallow anterior chamber in 6 cases (12.5%), hypotony in 3 cases (6.3%), and blocked stent in 3 cases (6.3%). The most common postoperative treatment was needling in 27 cases (56.3%). There was no significant difference in intraocular pressure among different types of glaucoma. In the comparison of postoperative effects of different surgical implantation methods for primary open-angle glaucoma, there were no statistically significant differences in intraocular pressure and the number of glaucoma medications at other follow-up time points except 1 month after surgery (P<0.05). Univariate logistic regression analysis did not find any risk factors associated with needling and surgical complete success. Conclusions: XEN-45 Gel Stent implantation is an effective and safe surgical option for different types of glaucoma patients in China, which can significantly reduce intraocular pressure and the use of glaucoma medications and has a high success rate. However, some patients may need needling or other treatments after surgery.

Design and Parameter Optimization of Rotary Double-Insertion Device for Small Arched Insertion Machine

China’s small arched shed-building machinery suffers from a low degree of mechanization, building efficiency, and qualification rate for frame insertion. Therefore, we designed a rotary double-insertion device and established the equation for its motion trajectory. The analysis shows that in the rotary insertion process, a better point of entry into the soil exists. A simulation model was constructed in ADAMS, and the static and dynamic trajectories were analyzed. Additionally, the optimal planting and insertion speed ratios were determined. Considering the qualified rate of the insertion frame as the evaluation index to establish a regression model, we adopted a three-factor three-level experimental design and established the planting speed ratio, center distance of the planting arm, and length of the pressing rod arm as the main influencing factors. We used Design-Expert 13 to perform the analysis of variance and determined the optimal parameter combinations. The experimental results show that the planting speed ratio was 0.7, the center distance of the planting arm group was 554 mm, the length of the pressing rod arm was 923 mm, and the qualification rate of trellis planting at this time was 98.05%. The bench was adjusted and tested based on the optimal parameter combination. The average value of the measured trellis qualification rate was 96.73%, and the relative error between the test value and the theoretical optimization value was 1.32%, thereby verifying the reliability of the optimal parameter combination. Field verification test results show that the rotary double-insertion device had a planting speed ratio of 0.7 and a trellis qualified rate of 95.74% compared with the theoretical optimization value of 2.31%. Conforming to the design requirements of small arch shed-building machinery, the prototype operation performance was stable.

Under-frequency load shedding setting method of new energy sending-end system based on improved IMQ-GWO algorithm

Aiming at the problems of low qualification rate, poor stability, and insufficient timeliness of the existing under-frequency load shedding implementation scheme at the new energy sending end, this paper proposes an under-frequency load shedding setting method for the new energy sending end system based on the improved IMQ-GWO algorithm. Firstly, considering the fluctuation of the trend of the line of the sending end system relative to the load curve of the whole network, the index system of the implementation scheme based on the under-frequency load shedding is established. Secondly, the objective function is established for the index system of the under-frequency load shedding scheme, and the under-frequency load shedding setting model is established considering the static constraints and transient constraints of the system. Then, the grey wolf optimization algorithm (GWO) is updated by using the characteristics of the IMQ function. At the same time, the individual position is adaptively updated based on the Sigmoid exponential function to better search and optimize the solution space of the problem. Finally, based on the modified IEEE39 node, the empirical analysis is carried out, and the improved IMQ-GWO algorithm proposed in this paper is used to solve the under-frequency load shedding setting model. It is proved that the proposed method is superior to other methods in terms of execution qualification rate, stability, and application timeliness.

水稻穴播器取种装置设计与试验

The core equipment of rice dry direct-seeding with film mulching devices shows poor adaptability to rice varieties, struggling to accommodate diverse seeding quantity for both hybrid and conventional rice varieties. A seed-filling component with unilateral and bilateral seed-filling function was designed to solve this challenge. Through theoretical analysis the key structural parameters of the seed-filling component were determined. Then Discrete Element Method (DEM) simulations were conducted to analyze the seeding performance, leading to the identification of optimal parameters for orifice width and orifice deflection angle of the seed-filling component, which are 7.7 to 8.5 mm and 1.71 to 2.41 degrees, respectively. Bench experiments using the central composite design indicates that the optimal parameters for the seed-filling component's orifice width and orifice deflection angle are 8.1 mm and 1.99 degrees, respectively. In the optimal combination of orifice parameters, for unilateral seed-filling in hybrid rice, the miss-seeding rate is 4%, the qualified rate is 84.8%, and the reseeding rate is 11.2%. For bilateral seed-filling in conventional rice, the miss-seeding rate is 4.2%, the qualified rate is 85.2%, and the reseeding rate is 10.6%. The result of field hole-seeding with film mulching is consistent with the result of indoor bench experiments, demonstrating that the seed-filling component of the hole seeder can meet the seeding requirements for rice precision direct-seeding with film mulching. This paper provides theoretical reference for the design and optimization of the seed-filling component for rice hole-seeding equipment.

玉米内充气压式高速精量排种器推种轮设计与试验

In order to improve the uniformity and stability of seed delivery and meet the requirements of precision sowing operation, a kind of seed push wheel designed to mesh with the seed discharging disk was developed. The wheel underwent theoretical analysis and experimental optimization regarding parameters such as tooth profile, tooth count, and tooth height. Using a pneumatically inflated maize precision seed-metering device as the seeding carrier, a full-factorial experiment was conducted with operational speed and tooth height as the experimental variables, and qualification rate, reseeding rate, and leakage rate as the performance indicators. A multivariate quadratic regression model was established to assess the relationships between the factors and indicators. The results indicated that optimal seed guiding performance was achieved when the seed push wheel had 9 teeth, a tooth height of 5.2–6.2 mm, and an operational speed of 9.0–12.6 km/h. This study provides a theoretical foundation and data support for the development of precision seeding technology and corresponding seed guiding devices.