Pure Ferrite Research Articles

Microstructural, magnetic, and optical properties of nickel-doped spinel zinc ferrite nanoparticles

This study focuses on the synthesis of nickel-substituted zinc ferrite nanoparticles, , via the sol-gel method and examines how nickel substitution influences their structural, magnetic, and optical properties. The lattice constant of the nanoparticles, which varied from 8.4296 Å to 8.4212 Å, decreased as the nickel concentration increased. Scanning electron microscopy (SEM) was employed to examine the morphology, revealing grain sizes between 46 and 53 nm, while energy dispersive X-ray spectroscopy (EDX) confirmed the elemental composition, showing nearly spherical nanoparticles containing all the constituent elements. The magnetic properties were analyzed using a vibrating sample magnetometer (VSM), which highlighted significant differences between the theoretical and experimental magnetic moments, indicating the presence of Yafet-Kittel magnetic ordering in the system. The saturation magnetization was enhanced by ions, reaching a maximum value of 23.864 emu/g. This enhancement makes the nickel-substituted zinc ferrite nanoparticles suitable for applications in data recording media and magnetic resonance imaging. Additionally, the values of the magnetic crystalline anisotropy constant, initial permeability, effective anisotropy constant, and anisotropic field of the synthesized samples were estimated.The optical properties of the synthesized samples were evaluated using UV-visible spectroscopy, and the band gap was determined through diffuse reflectance spectroscopy (DRS). The optical bandgap of pure zinc ferrite was measured to be 2.26 eV, and it decreased with increasing nickel concentration in the nanoparticles.

Optimization of structural, optical, dielectric and magnetic properties of Gd3+ substituted Mg-Mn mixed spinel ferrite ceramics

Manganese magnesium ferrite (Mg0.5Mn0.5Fe2O4) and Gd doped Mg0.5Mn0.5Fe2O4 (Mg0.5Mn0.5Fe2-xGdxO4 (x = 0.0, 0.1, 0.2, 0.3, 0.4, 0.5) were synthesized using the solid-state method. The structural study was performed using the powder X-ray diffraction (XRD) technique. The XRD plot confirms the presence of a spinel cubic structure for pure MgMn ferrite and the existence of a secondary GdFeO3 phase in addition to the cubic spinel phase for Gd-doped MgMn ferrite. The average crystallite size estimated from the Williamson-Hall plot decreases from 42.75 nm to 18.97 nm with the increase in Gd content. The microstructural study confirms the clear grains with well-defined grain boundaries. The Fourier Transform Infrared (FTIR) spectra of the samples show the vibrational bands at 3440 cm−1, 1636 cm−1, 1385 cm−1, 1100 cm−1, and 560 cm−1 assigned to tetrahedral and octahedral sites. The improvement in dielectric property has been observed for Gd-doped samples. The saturation magnetization and remnant magnetization decrease from 0.7 to 0.3 emu and 0.035 to 0.0273 emu respectively. The coercivity increases from 31 to 75 Oe with the increase in Gd content. The fabricated spinel ferrites have significant electrical and magnetic properties which may be promising candidates for microwave devices.

Hybrid magnetic nanocomposite NiFe2O4/TiO2 for Photocatalytic dye degradation and green hydrogen (H2) generation

The present paper focuses on designing and developing nanocomposites to modify their properties to increase the ability to generate hydrogen and degrade photocatalytic dyes. A nanocomposite of nickel ferrite (NiFe2O4)/Titanium dioxide (TiO2) was formulated using the sol-gel self-ignition method. X-ray diffraction (XRD) tool was adopted to analyze the structural behavior of pure nickel ferrite (NiFe2O4), pure titanium dioxide (TiO2), and nanocomposite of NiFe2O4/TiO2. XRD pattern of NiFe2O4 and TiO2 shows a monophasic nature whereas the XRD pattern of nanocomposites shows mixed phases of NiFe2O4 and TiO2. FTIR spectra confirm the formation of NiFe2O4, TiO2, and their composites with absorption bands near 400 cm-1 and 600 cm-1, 1500 cm-1. Raman spectra unveiled the presence of five active Raman modes in the case of NiFe2O4 whereas three active Raman modes are seen in TiO2. Field emission scanning electron microscopy (FE-SEM) images exposed the dense structure with spherical cluster-like morphology in the case of NiFe2O4. Energy-dispersive X-ray spectroscopy (EDX) analysis confirms the presence of all the desired elements of NiFe2O4, TiO2, and their composites in stoichiometric proportions. BET analysis of nickel ferrite NPs suggests a large surface area of the order of 31.54 m2/gm in comparison with TiO2 (19.23 m2/gm). The optical characterization was made through the UV-visible spectroscopic technique. TiO2 shows a maximum band gap of the order of 3.02 eV while NiFe2O4 shows a low band gap of the order of 1.74 eV. A typical M-H curve with saturation magnetization of the order of 27.54 emu/gm was observed for pure NiFe2O4. No magnetic properties were observed for TiO2 as it is a semiconductor. Enhancement in magnetic properties is observed with increases in NiFe2O4 content in a composite of NiFe2O4/TiO2. The photocatalytic activities were examined by degrading Methylene Blue (MB) dye under sunlight for pure nickel ferrite (NiFe2O4), pure titanium dioxide (TiO2), and a nanocomposite of NiFe2O4/TiO2. Photocatalytic hydrogen production reactions were carried out in a methanol/water solution under visible light. Consequently, the best configuration of the photocatalyst was determined as 25% wt% NiFe2O4/ TiO2 which had shown the maximum hydrogen (H2) production rate as 146.3 μmol/g/h after 8 h owing to its reduced bandgap energy and delayed e- / h+ recombination.

The role of phase transformation (tetragonal – spinel) on the structural and mechanical properties of Ni doped CuFe2O4

Nano-ferrites of Cu1–xNixFe2O4 (x = 0 to 1 with step 0.2) system was synthesized utilizing the flash auto combustion process annealed at 600oC for 3 h. The structural characterization for synthesized samples was carried out using x-ray Diffraction (XRD), Fourier transition infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The hardness of the prepared material was measured using micro-indentation creep technology. XRD pattern verified the creation of a single-phase cubic spinel structure. The undesired CuO phase forms around \\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\:2\ heta\\:={50}^{^\\circ\\:}\\:$$\\end{document}for pure Copper ferrite and decreases with increasing Ni content. The average crystalline size decreases from 27.92 nm to 13.28 nm by doping process from x = 0.2 to x = 1 which retards the growth of crystalline size. FTIR spectra are distinguished by the presence of two prominent absorption bands, ν2 for the octahedral site and ν1 for the tetrahedral site, in the range of approximately 593 and 471 cm− 1, respectively. FTIR analysis verified the formation of the ferrite system’s spinel structure. The TEM images show a nanocrystalline nature with some agglomeration and the crystallites are spherical in shape which their sizes are agrees well with that obtained from XRD measurements. The hardness decreases as the dwell time increases. The hardness and yield strength (Y) values were significantly improved due to the decrease in the crystallite size after Ni doping. The stress exponent (n) value increases by increasing Ni content which means that the mechanical properties improved due to increment of resistance.

Facile synthesis of samarium (Sm3+) doped cobalt-iron oxide nano ferrite as an advanced electrode material for possible supercapacitor applications

Herein, we present design and fabrication of Samarium (Sm3+) doped cobalt-iron oxide ferrites nanocomposite electrode as an efficient energy storage material for supercapacitors. We employed a simple, low cost and quick one step solution combustion method to synthesize CoFe2-xSmxO4 (x = 0.0, 0.050, 0.075 and 0.1) ferrites. The morphological and structural features of synthesized CoFe2-xSmxO4 ferrites were analysed through various analytical and spectroscopic characterization methods such as scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscope (TEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). These analytical techniques confirm the successful doping of Samarium (Sm3+) into cobalt-iron ferrite, and the doping does not affect the crystalline structure of pure ferrite. The electrochemical properties of the synthesized ferrites were significantly improved after Samarium (Sm3+) doping into the host cobalt-iron-oxide. The highest specific capacity about 314 F/g was achieved for CoFe2-xSmxO4 (x = 0.1) composite electrode material, in comparison to pure CoFe2-xSmxO4 (x = 0) which is about 125 F/g. However, CoFe2-xSmxO4 (x = 0.1) ferrite shows a superior capacitance retention of the order of 98 % even after 5000 cycles of operation at a scan rate of 250 mV/s. The electrode material fabricated by using CoFe2-xSmxO4 ferrite renders an energy density of 30.16 W h/kg at a power density of 400 W h/kg. The results obtained in presented studies opens new avenues for the fabrication high-performance electrode material for supercapacitor that could be well suited for light weight electronic devices, electric vehicles, and forthcoming generation supercapacitor applications.

Enhanced dielectric properties of copper substituted nickel ferrite nanoparticles for energy storage applications

In this study, it was aimed to obtain copper-substituted nickel ferrite nanoparticles, which are advantageous for use in energy storage devices such as batteries and supercapacitors that provide high energy storage capability with their high dielectric behavior, by co-precipitation method. Nickel ferrite nanoparticles in the form of CuxNi1-xFe2O4 containing copper substitution at ratios for x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0 were synthesized. X-ray diffraction Method (XRD) was used to analyze the spinel structure, the purity phase, and the crystalline size of the nanoparticles. Field Emission Scanning Electron Microscopy (FE-SEM), and Fourier Transform Infrared (FTIR) Spectroscopy were also performed to investigate the particle size, morphological distribution, and the functional groups of the samples. The structural analyses confirmed the successfully produced single-phase pure cubic spinel nickel ferrite and copper-substituted nickel ferrites with nanometer-scale particle distribution. The Impedance Spectroscopy technique was used for the characterization of the dielectric properties of the samples. Frequency-dependent complex dielectric, impedance, modulus, and alternating current (AC) conductivity mechanisms of the copper-doped nickel ferrite nanoparticles (CuxNi1-xFe2O4) were determined. The results showed that copper-induced nickel ferrite nanoparticles display a promising dielectric material consisting of grains and grain boundaries which are confirmed by Maxwell-Wagner interface-type polarization, which is in agreement with Koop's theory. Furthermore, a remarkable enhancement is obtained on the dielectric parameters of copper-induced nickel ferrites for x = 0.2, and it is seen that this is a critical value on the doping ratio. In addition, the dielectric parameters decreased between x = 0.2–0.8 ratios but still showed higher values than pure nickel ferrites, confirming that nickel ferrites have a tunable dielectric behavior depending on the stoichiometric copper doping ratios. Therefore, this may make them a promising dielectric medium for further studies in various electronic device applications.

Tuning optical, magnetic, and electrical parameters of CuFe2O4 nanoparticles incorporated with GO and ZnO using a facile synthesis

Nano-ferrites, metal oxides, and carbon-based nanomaterials have been used frequently to enhance optical and magnetic prospects for latent applications. Copper ferrite/Graphene Oxide and Zinc Oxide (CuFe2O4/GO/ZnO) ternary nanocomposite synthesized by hydrothermal route showed dramatically good outcomes as the band gap energy value of synthesized nanocomposite approaches to 2.4 eV. Furthermore, the light absorbance of CuFe2O4 increases by adding ZnO and GO. The experimental data revealed the face-centered cubic structure (FCC) of pure spinal ferrite (CuFe2O4) nanoparticles even after adding ZnO and GO. The 2θ peak observed at 31.70° with (220) hkl planes indicates the successful addition of ZnO nanoparticles in CuFe2O4/GO nanocomposite. XRD graph, the absence of characteristic peaks of GO revealed the intercalation of CuFe2O4 nanoparticles with GO layers. In SEM images, agglomeration among CuFe2O4 nanoparticles is observed due to the magnetic interaction of nano-crystallite with a high surface-to-volume (S/V) ratio. VSM can be used to determine the magnetic properties of as-synthesized samples at moderate temperatures under 0–0.5 and ± 5 tesla. In CuFe2O4/GO/ZnO ternary nanocomposite, the saturation magnetization value reduces from 2.071 to 1.365 emu/g due to the addition of ZnO nanoparticles. The loops were narrowed showing a decrease in the coercive field with the addition of ZnO nanoparticles in CuFe2O4/GO ternary nanocomposite material. Moreover, the study of electrical properties of pure CuFe2O4 and CuFe2O4/GO/ZnO ternary nanocomposite revealed that the values of dielectric constant and tangent loss decrease at high frequencies owing to surface charge polarization and intrinsic dipole interactions. The study of the electrical properties of both pure CuFe2O4 and the CuFe2O4/GO/ZnO ternary nanocomposite reveals that the dielectric constant (ε’) and tangent loss (tanδ) exhibit a decreasing trend as the frequency increases. This behavior is attributed to surface charge polarization and intrinsic dipole interactions. At lower frequencies, both samples display elevated values for these properties, which stabilize as the frequency increases beyond 2 MHz. Notably, high AC conductivity is observed in both samples, attributed to increased capacitance and resistance.

Significant enhancement of piezoelectric photocatalytic activity in Mn-doped BiFeO3

Ultrasonic vibration and light irradiation can be used together to slow down the rapid recombination of light-induced charges during the catalytic process. One way to enhance the catalytic performance is by introducing different elements into the structure. In this study, pure bismuth ferrite (BiFeO3) and manganese (Mn)-doped bismuth ferrite (BFMO) nanomaterials were successfully synthesized by electrostatic spinning. These materials were then tested for their ability to degrade rhodamine B (RhB). The best-performing material was BiFe0.85Mn0.15O3, which achieved almost complete removal of RhB within 100 min. The degradation rate of this material was 3.3 times higher than that of pristine BiFeO3. This enhanced catalytic activity can be attributed to the wider range of light absorption and the synergistic enhancement of the piezoelectric response, which promotes the movement of free carriers. In addition, the synthesized catalysts have good stability and reusability, with little metal leaching after multiple uses. Free radical scavenging experiments tests showed that ·OH and holes are the main active species in the catalytic process. This work paves a new approach for creating highly efficient piezoelectric catalysts and expands the application of BiFeO3-based materials for wastewater purification.

Fabrication and characterization of rubidium ferrites by the solution‐based combustion method using diverse organic fuels

Fabrication and characterization of rubidium ferrites by the solution‐based combustion method using diverse organic fuels

NiO/MnFe2O4 Nanocomposite Photoluminescence, Structural, Morphological, Magnetic, and Optical Properties: Photocatalytic Removal of Cresol Red under Visible Light Irradiation.

In this study, pure nickel oxide (NiO), manganese ferrite (MnFe2O4 or MFO), and binary nickel oxide/manganese ferrite (NiO/MFO1-4) nanocomposites (NCs) were synthesized using the Sol-Gel method. A comprehensive investigation into their photoluminescence, structural, morphological, magnetic, optical, and photocatalytic properties was conducted. Raman analysis, UV-Vis spectroscopy, Fourier-transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction techniques were used to characterize the materials. The synthesized samples exhibited superparamagnetic behavior, as revealed by our analysis of their magnetic properties. A lower recombination rate was shown by the photoluminescence analysis, which is helpful for raising photocatalytic activity. The photocatalytic activity was evaluated for the degradation of Cresol Red (CR) dye. 91.6% of CR dye was degraded by NiO/MFO-4 nanocomposite, and the NC dosage as well as solution pH affected the photocatalytic performance significantly. In four sequential photocatalytic cycles, the magnetically separable NCs were stable and recyclable. The enhanced photocatalytic activity and magnetic separability revealed the potential application of NiO/MFO-4 as an efficient photocatalyst for the removal of dyes from industrial wastewater under solar light irradiation.

CoFe2O4/PANI/MWCNTs ternary hybrid composites. Synthesis, characterization, the effect of MWCNTs ratio and dye removal capability.

We have synthesized cobalt ferrite (CoFe2O4) using the sucrose auto-combustion method and subsequently employed the in situ polymerization technique to fabricate ternary composites comprising CoFe2O4, polyaniline (PANI), and multi-walled carbon nanotubes (MWCNTs). In this novel investigation, we explored the influence of varying MWCNTs ratios on these composites' structural, magnetic, thermal, and electrical properties. The crystal structures of the synthesized composites were analyzed using X-ray diffraction (XRD), while Fourier transform infrared (FT-IR) spectroscopy revealed changes in bonding patterns, including the disappearance of ferrite bonds and the emergence of new ones. Transmission electron microscopy (TEM) images illustrated a complete coating of PANI on both MWCNTs and CoFe2O4 particles, resulting in a substantial reduction in magnetization compared to pure CoFe2O4 ferrite due to PANI's nonmagnetic nature. Vibrating sample magnetometer (VSM) measurements confirmed this reduction, indicating a decrease to 7.3 emu.g-1. Thermal analysis demonstrated an enhancement in thermal stability with increasing MWCNTs content, as evidenced by an increase in the temperature equivalent for half decomposition (T50) from 486 to 522°C for composites with 40% MWCNTs. Moreover, the electrical conductivity showed a corresponding rise with MWCNTs content, increasing from 3.1 × 10-3 Ω-1.cm-1 to 2.2 × 10-2 Ω-1.cm-1, possibly indicating charge transfer from PANI to MWCNTs. To assess practical applications, we investigated the ability of the composite with 40% MWCNTs to remove phenol red (PR) dye from aqueous solutions. Through a systematic study of adsorption parameters and kinetics, we determined optimal conditions for effective dye removal and elucidated the underlying adsorption mechanism. Our results demonstrated the composite's efficiency in dye removal, with a 6.4mg·g-1 capacity for PR dye, highlighting its potential for environmental remediation efforts.

Visible light-induced photocatalytic degradation of methylene blue dye using pure phase bismuth ferrite nanoparticles

The degradation of organic dyes in wastewater has become a significant environmental issue, requiring the development of degradation technologies that are both effective and environmentally friendly. The present study employed the sol-gel approach to synthesize nanoparticles of phase pure bismuth ferrite (BiFeO3). The nanoparticles were assessed for their ability to efficiently degrade methylene blue (MB) dye, especially under visible light irradiation. The X-ray diffractogram (XRD) confirmed the formation of BiFeO3 nanoparticles, with an average crystallite size of 48 nm. The material's band gap, with a value of 1.84 eV, demonstrates its capacity to effectively absorb light, including wavelengths within the visible spectrum. Scanning electron microscopy (SEM) was used to identify porous aggregated particles. Both Raman and Fourier transform infrared spectroscopy (FTIR) confirm the successful synthesis of pure BiFeO3 in the desired phase. The BiFeO3 photocatalyst exhibited a significant surface area and isotherms of type IV, a characteristic typically observed in mesoporous materials, as determined by the Brunauer-Emmett-Teller (BET) analysis. The efficacy of BiFeO3 nanoparticles in facilitating the decomposition of MB in a water-based solution was evaluated by visible light photocatalysis. An efficiency degradation of 98.49 % was recorded for MB within 2 h.

Effect of Cr and Ni on mechanical response and microstructural evolution of nanocrystalline ferrite: A molecular dynamics study

Microalloying plays a critical role in improving the mechanical properties of steel. To offer a better theoretical guide for experimental research at the atomic level, this paper investigated the synergistic mechanism of adding trace amounts of alloy Cr and Ni and the microstructure evolution of nanocrystalline ferrite during the mechanical response process. First-principles calculations were implemented to investigate electronic properties. Hybrid molecular dynamics and Monte Carlo simulations were employed to explore the deformation mechanism under uniaxial tension and scratching. Specifically, comprehensive differences between doped and pure nanocrystalline ferrites were explored regarding local stress-strain state, dislocation evolution, twin expansion, and grain boundary activity. The results show that Cr- and Ni-doped nanocrystalline ferrite has higher strength and better wear resistance. The potential mechanism is that the addition of Cr and Ni enhances the atomic bonding strength with Fe atoms, hinders the movement of dislocations caused by lattice distortion, and suppresses grain boundary slip and migration, thereby improving the resistance to plastic deformation and grain boundary stability. Theoretical calculations based on microstructure indicate that compared to solid solution strengthening, Ni-induced grain boundary strengthening plays a dominant role in improving yield strength. Under large deformation, the trend of mechanical response is reversed. The suppression of dislocation motion by Cr reduces the dislocation density and dislocation entanglement, resulting in flow stress and local scratch force being smaller than that of pure samples. However, the formation of more nanoscale twins and twin-dislocation interactions enhances strain-hardening ability during tensile. Finer nanostructured subgrains are formed under scratching. These results provide valuable insights into the understanding of the strengthening mechanism and plastic deformation mechanism of Cr-Ni system low alloy steel under dynamic loading.

Enhancement of magnetization and optical properties of CuFe2O4/ZnFe2O4 core/shell nanostructure

In this work, core/shell of CuFe2O4/ZnFe2O4 nanostructure composite was prepared by hydrothermal method. X-ray diffraction (XRD) analysis, transmission electron microscope imaging, energy dispersive X-ray (EDX), and Fourier transform infrared techniques were used to prove the phase formation, morphology, elemental analysis, and cation distribution of core/shell structure, respectively. Furthermore, measurement of the optical properties proved the decrease of photoluminescence (PL) efficiency. The magnetic measurements showed an enhancement of the magnetization by about 63% relative to pure Cu ferrite, and the magnetization curve exhibited superparamagnetic behavior. These results were explained in terms of the depression of the magnetic dead layer thickness in the core/shell structure. The results unleash the promising applications of the prepared samples as transformer cores in the high frequency range and as a photocatalytic agent for water purification and hydrogen production.

Preparation, characterization and photocatalytic activity for degradation of methylene blue by ZnFe<sub>2</sub>O<sub>4</sub>/Bentonite nanocomposite

In this work, we report synthesis of bentonite (BT) supported softmagnetic ZnFe2O4 nanoparticles to obtain ZnFe2O4/BT. The composition, surface morphology and optical properties of the sample were characterized by XRD, EDX, FTIR, SEM and DRS analysis. The results of SEM show that the ZnFe2O4 nanoparticles spread on the thin layer of bentonite due to intercalation with bentonite. The band gaps of Bentonite, ZnFe2O4 and ZnFe2O4/BT are 2.18; 1.95 and 1.82 eV respectively. The photocatalytic activity of the samples is evaluated by the degradation of methylene blue (MB) in the presence of H2O2 under visible light radiation. The results indicated that the ZnFe2O4/BT samples exhibited higher removal efficiencies than the pure ZnFe2O4 ferrites. The enhanced photocatalytic activity of the ZnFe2O4/BT is explained due to visible light adsorption ability, and larger interfacial area, as well as the efficient separation mechanism of photoinduced electron and holes.

Highly nanocrystalline Mg doped ZnFe2O4 powders for rapid and simultaneous adsorption of Lead, Copper, and Cadmium heavy metals ions in synthetic / sea waters

This research aims to investigate the effect of Mg doping on individual and simultaneous adsorption of Pb+2, Cu+2, and Cd+2 heavy metals in aqueous solution and in seawater samples, by Zinc ferrite nanoparticles. The Mg-doped Zinc ferrite nanoparticles are synthesized successfully by the sol-gel route and varying Mg concentrations. TEM, XRD, FTIR, Raman, and XPS characterizations confirm the cubic spinel structure of Zinc ferrite with a semi-spherical shaped nanosized particles (10-15nm) irrespective of Mg doping content. The BET surface area manifests a significant increase within Mg doping (39.3 m2/g) compared with the pure zinc ferrite (28.4 m2/g). Accordingly, Mg-doped Zinc ferrite powders demonstrate considerable adsorption capacities for Pb+2 (143.5mg/g), Cu+2 (117mg/g), and Cd+2 (77mg/g) within 2h under optimized experimental conditions. The prepared nanopowders exhibit high selectivity towards Pb+2 in simultaneous adsorption in aqueous solutions (85mg/g) and real seawater samples. Nonetheless, the selectivity of Pb+2 ions drops dramatically to 25mg/g within real seawater samples due to the strong ionic strength of high-salinity seawater. This study provides insights into the importance of doped spinel ferrite nanoparticles in highly efficient, rapid, and simultaneous adsorption of heavy metals. Besides, it reveals the challenge of performing the adsorption process in real seawater.

Negative permittivity and permeability behaviour of SrFe12O19/rGO metacomposite for microwave absorption in 2–18 GHz range

Double-negative performance has played a significant role in electronic applications owing to its both permeability and permittivity negative values. Microwave absorption material has a substantial role in electromagnetic shielding, radar absorption, stealth applications, etc. Herein, a novel double-negative metacomposite, SrFe12O19/rGO, was designed by a simple one-pot hydrothermal method, and the microwave absorption properties of the material were studied in the microwave region from 2 to 18 GHz using VNA analysis. The structural and morphological studies were analysed using XRD, FT-IR, and SEM instrumentation techniques and the magnetic property of the material was studied using VSM analysis. Both studies confirmed the hard magnetic nature of the material. The particle sizes of SrFe12O19 and SrFe12O19/rGO measured from XRD are 55.60 nm and 41.55 nm, respectively. Hexagonal plate-like morphology were observed from FESEM images. The coercivity of SrFe12O19/rGO increased, and the magnetocrystalline anisotropy was changed due to the decrease in particle size. The magnetic saturation value decreases due to the presence of non-magnetic rGO. The resultant SrFe12O19/rGO metacomposite shows negative permittivity and permeability values. The minimum reflection loss values observed for pure and rGO-decorated strontium ferrites are −28.49 dB at 7.76 GHz and −23.78 at 11.04 GHz, respectively. In addition to experimental results, simulation studies were also performed to study the reflection loss with matching thickness using a quarter wavelength mechanism. The results show that this composite can be employed as a left-handed metamaterial that finds applications in absorption, antennas, sensors, wireless power transfer systems, etc. The left-handed metamaterial can shift the frequency region from a lower to a higher frequency region. The rGO decorated metacomposite is a promising material for microwave absorption at higher frequency regions.

SÍNTESE, CARACTERIZAÇÃO, ATIVIDADE ANTIMICROBIANA DE NANOPARTÍCULAS DE FERRITA DE COBRE E SUA INCORPORAÇÃO EM CIMENTO DE IONÔMERO DE VIDRO

SYNTHESIS, CHARACTERIZATION, ANTIMICROBIAL ACTIVITY OF COPPER FERRITE NANOPARTICLES AND THEIR INCORPORATION IN GLASS IONOMER CEMENT. Pure cubic copper ferrite (c-CuFe2O4), cerium-doped cubic copper ferrite (c-CuCeFe2O4) and pure tetragonal copper ferrite (t-CuFe2O4) nanoparticles were synthesized from the proteic sol-gel method, and characterized by X-ray diffraction, Rietveld method, FT-IR spectroscopy, and field emission scanning electron microscope. The antibacterial activity of the particles was tested in vitro against pathogenic Gram-positive, Gram-negative bacteria. Thus, it has been observed that the nanoparticles are capable of inhibiting the growth of such microorganisms. The nanoparticles were incorporated into glass ionomer cement, followed by Vickers microhardness evaluation. It is concluded that the cubic copper ferrite showed the best antimicrobial result, being the most suitable for market studies (industrial and biomedical).

Crystal structure and magnetic properties ferrites Ba-Fe-O, Bi-Fe-O, synthesized in NGO “Physics-Sun”

Alloys based on Ba-Fe-O have been synthesized in a large solar furnace NGO “Physics-Sun”. The obtained barium hex ferrite with magnetic characteristics suitable for solving technical problems for the manufacture of protective coatings. The experimentally observed increase in the specific magnetization of BiFe0.75Ni0.25O3 with respect to the data obtained in nominally pure bismuth ferrite is associated both with the suppression of the cycloidal spin structure due to the partial substitution of nickel cations for iron cations and with the establishment of ferromagnetic exchange interaction between neighboring Fe3+ and Ni3+ ions. The results of ab initio (LSDA + U approximation of the DFT method) calculations of the band structure suggest that in the ground state BiFe0.75Ni0.25O3 is a semiconductor with a band gap of 1.94 eV.

Sol-gel Synthesis of Mn-substituted Copper Ferrite Nano Particles as Anode for Lithium Ion Batteries

Mn substituted copper ferrites (MnxCu1-xFe2O4, x = 0, 0.33, 0.67, 1.00) have been synthesized from metal nitrates and citric acid by sol-gel method (chemical process). This study aims to know the effects of Mn substitution on structural, magnetic, and electrochemical properties of copper ferrites. For characterizing the prepared ferrites, different techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy were used. In addition, vibrating sample magnetometer (VSM) is used to investigate the magnetic properties such as saturation magnetization (Ms), residual magnetism (Mr) and coercive force (Hc). A single-phase spinal structure was confirmed by XRD and lattice parameter was increased from 8.36 Å to 8.52 Å with increasing Mn contents. Micrographs of SEM shows that nanoparticles are agglomerated and non-uniform in size. The FTIR analysis shows that theses absorption band about 1422 cm-1 to 1434 cm-1 was attributed octahedral B-site. For pure copper ferrite, band is shifted towards higher frequency by manganese content. The results from CV showed that the increasing in scan rate and specific capacitance decreases due to increase in the area loop which clearly means that the investigated samples are best for storage devices such as lithium ion batteries (LIBs).