Pumping Scheme Research Articles

Spin injection enhancement in CW VECSEL at room temperature using push-pull optical pumping.

We report the enhancement of spin injection efficiency in an external-cavity VCSEL based on a non-resonant pumping coupled with a polarized optical resonant illumination. This double pumping scheme allows both the injection of spin polarized electrons in the conduction band and the selection of the spin orientation for the electron/hole recombination laser process. Experimentally, a flip of the polarization state of the laser is achieved with an ellipticity of +31° (spin down) and -33° (spin up), so an increase of about 50% of the ellipticity is achieved in comparison to an optical non-resonant pumping alone.

Diode-pumped continuous-wave Pr:YLF cyan laser

We demonstrate continuous-wave quasi-three-energy level laser operation in the cyan region with an LD-pumped Pr:YLF laser. Based on the 3P0→3H4 transition, a continuously tunable Pr:YLF cyan laser was realized with a wavelength tunable range of 490.41 nm–491.72 nm, corresponding to a maximum power of 72 mW–244 mW. Under the same pumping scheme, a maximum output power of 255 mW was achieved at 491 nm using Pr:YLF, corresponding to a slope efficiency of 7.2 %. To our knowledge, this is the highest power produced at room temperature by a cyan laser demonstrated with a Pr:YLF crystal. This work provides a simple and effective scheme to generate high-power cyan lasers at room temperature for various applications, such as underwater communications and fluorescence detection.

On-chip integrated few-mode erbium–ytterbium co-doped waveguide amplifiers

We propose for the first time, to the best of our knowledge, an on-chip integrated few-mode erbium–ytterbium co-doped waveguide amplifier based on an 800 nm thick Si3N4 platform, which demonstrates high amplification gains and low differential modal gains (DMGs) simultaneously. An eccentric waveguide structure and a co-propagating pumping scheme are adopted to balance the gain of each mode. A hybrid mode/polarization/wavelength-division (de)multiplexer with low insertion loss and crosstalk is used for multiplexing and demultiplexing in two operation wavebands centered at 1550 nm and 980 nm, where the light in these two bands serves as the signal light and pump light of the amplifier, respectively. The results demonstrate that with an input signal power of 0.1 mW, TE0 mode pump power of 300 mW, and TE1 mode pump power of 500 mW, the three signal modes (TE0/TM0/TE1) all exhibit amplification gains exceeding 30 dB, while maintaining a DMG of less than 0.1 dB.

A new longitudinal pumping scheme that uses elliptical laser beams to improve the compactness and efficiency of high-power dye lasers

Liquid dye lasers are intrinsically suitable for high-average-power operation because their flowing laser gain media can effectively remove the heat produced by laser amplification; thus, liquid dye lasers have a significant place in various laser applications. However, to sufficiently remove the dye solution heated by the laser, a very cumbersome dye flow system is required to achieve a high flow velocity in the dye cell of a high-power dye laser, which limits its applications. In this paper, we found that the pressure and power required to drive the high-speed dye flow are both proportional to the square of the laser beam size along the direction of the flow. Based on this result, we proposed a novel longitudinal pumping scheme that uses elliptical laser beams. This new scheme can significantly reduce the size and energy consumption of dye flow loops in high-power dye lasers. We also developed a dye laser system with a main amplifier using a 1 mm × 4 mm elliptical input laser beam. The amplifier produced an average power of 135 W with a repetition rate of 10 kHz and a conversion efficiency of 39.5%. The M2 factor of the output beam was better than 1.7. The flow parameters to drive the dye flow loops were 2.1×105 Pa, and 0.43 L/s, which gave a clearing ratio of 2 for the amplifier. This new pumping scheme enables high-power dye lasers to be more compact and efficient, making them more flexible for various applications.

The design and optimization methods towards 10 kW high beam quality fiber laser based on counter tandem pumping scheme

The design and optimization methods towards 10 kW high beam quality fiber laser based on counter tandem pumping scheme

HEAT PUMPS AS AN ENERGY-EFFICIENT MEANS OF GRAIN DRYING

Large energy costs for the process of drying grain crops associated with the increase in the price of energy carriers pose the task of reducing the energy component to the developers. The presented article focuses on the development of measures to reduce energy costs for the grain drying process using heat pumps. The considered advantages of heat pumps indicate the possibility of using these units for drying grain crops. Especially noteworthy is the increase in energy efficiency of heat pumps due to the conversion of ambient heat with a low temperature potential into heat with a high temperature potential. Thus, heat pumps are characterized by the heat pump conversion factor, which indicates their efficiency. The presented schemes with a heat pump implement the drying process in convective dryers, in particular in chamber, tunnel, shaft and drum dryers. Different schemes of heat pumps can be used for different types of dryers. The use of alternative drying sources for grain drying, in particular solar energy in the heat pump system, dramatically increases the efficiency of this installation. Also presented is a comprehensive scheme for the utilization of spent coolant in heat exchangers, an economizer, and a heat pump, which comprehensively addresses the issue of coolant utilization in a chamber dryer. In the drum dryer, the utilization of the spent coolant in heat exchangers and a heat pump is provided, increasing the temperature of the drying agent at the entrance to the dryer. For drying plant raw materials in a two-zone tunnel dryer, a heat pump scheme with two temperature levels of the heat carrier was developed for drying the material at different temperatures in the dryer zones.

Theoretical Analysis of Integrated Nanophotonic Q‐Switched Laser Based on Gain and Saturable Absorption by Two‐Dimensional Materials

A nanophotonic passively Q‐switched lasing element in the near infrared is proposed and theoretically investigated. It consists of a silicon‐rich nitride disk resonator enhanced with the contemporary hetero‐bilayer and a graphene monolayer to provide gain and saturable absorption, respectively. The two‐dimensional materials are placed on top of the disk resonator and are separated by a spacer of hexagonal boron nitride. emits at 1128 nm due to the radiative recombination of interlayer excitons after being optically pumped at 740 nm. Optical pumping is conducted in a guided‐wave manner aiming at achieving a high overall efficiency by critically coupling to a cavity mode near the pump transition. The response of the proposed pulsed laser is assessed by utilizing a coupled‐mode theory framework fed with linear finite‐element method simulations, rigorously derived from the Maxwell–Bloch equations. Following a meticulous design process and exploiting the guided pumping scheme, an ultralow lasing threshold of just μW is obtained. Overall, the Q‐switched laser delivers pulsed light inside an integrated bus waveguide with mW peak power, ps duration, and GHz repetition rates requiring sub‐mW continuous wave pumping. These properties are highly promising for communication applications and highlight the potential of two‐dimensional materials for nanophotonic light sources.

Design optimization of Yb-doped fiber lasers for operation in radiation environments

AbstractRadiation hardening should be considered for various active fiber systems operated in adverse environments to reduce their sensitivity to complex ionizing radiations. And, architecture optimization through numerical simulation provides an efficient choice. Here, introducing radiation effects into the conventional fiber laser model, a radiation model concerning the design optimization of low- and moderate-power Yb-doped fiber lasers is developed. And, experiments at different radiation levels up to 750 Gy are carried out for validation, demonstrating the ability of this model to correctly simulate the performance of the Yb-doped fiber laser in harsh environments. Then, with this model, impacts of active fiber length, pump scheme, and pump allocation on the output characteristics of Yb-doped fiber lasers are analyzed numerically. And, optimization of Yb-doped fiber lasers are conducted through architecture design. Simulations show that a proper design with relatively short active fiber and dynamic pump allocation can remarkably improve the radiation tolerance of Yb-doped fiber lasers.

Dissipative Kerr soliton generation at 2μm in a silicon nitride microresonator

Chip-scale optical frequency combs enable the generation of highly-coherent pulsed light at gigahertz-level repetition rates, with potential technological impact ranging from telecommunications to sensing and spectroscopy. In combination with techniques such as dual-comb spectroscopy, their utilization would be particularly beneficial for sensing of molecular species in the mid-infrared spectrum, in an integrated fashion. However, few demonstrations of direct microcomb generation within this spectral region have been showcased so far. In this work, we report the generation of Kerr soliton microcombs in silicon nitride integrated photonics. Leveraging a high-Q silicon nitride microresonator, our device achieves soliton generation under milliwatt-level pumping at 1.97 µm, with a generated spectrum encompassing a 422 nm bandwidth and extending up to 2.25 µm. The use of a dual pumping scheme allows reliable access to several comb states, including primary combs, modulation instability combs, as well as multi- and single-soliton states, the latter exhibiting high stability and low phase noise. Our work extends the domain of silicon nitride based Kerr microcombs towards the mid-infrared using accessible factory-grade technology and lays the foundations for the realization of fully integrated mid-infrared comb sources.

Control of Carbon Dioxide Bivalent Heat Pump on Heating of Buildings

The scheme of a bivalent heat pump (BHP) is considered, using both the heat of the water from the return network and the heat of the outside air as low-potential heat sources (LPH). The aim of the work is to create a BHP circuit that provides functioning at the variable heat load temperature. The goal was achieved by solving the following problems: analysis of methods of synthesis of BHP circuits, analysis of circuit operation under random disturbances and development of the automatic control systems for BHP. The most significant result of the work is: a heat pump circuit that can operate at variable pressures of the evaporator and the gas cooler. The next significant result is, for bivalent heat pumps intended for operation in heat supply systems with qualitative and qualitative-quantitative laws of thermal control, the introduction into the heat pump circuit of a heat exchanger installed in the return water circuit of the secondary building and cooled by outside air, as well as two control valves installed in series between the gas cooler and the evaporator, the first valve installed along the refrigerant flow being controlled by a signal based on the pressure difference between the outlet of the gas cooler and the separation vessel between the evaporator and the gas cooler, and the second by pressure in front of the evaporator. The significance of the obtained results lies in the increase of the COP of the heat pump, due to the increase of heat transfer in the gas cooler circuit. The HHP circuit differs from the known ones in that it uses two control valves and the heat exchanger for additional cooling of the return water of the BHP heated building.

Thouless pumping in Josephson junction arrays

Recent advancements in fabrication techniques have enabled unprecedented clean interfaces and gate tunability in semiconductor-superconductor heterostructures. Inspired by these developments, we propose protocols to realize Thouless quantum pumping in electrically tunable Josephson junction arrays. We analyze, in particular, the implementation of the Rice-Mele and the Harper-Hofstadter pumping schemes, whose realization would validate these systems as flexible platforms for quantum simulations. We investigate numerically the long-time behavior of chains of controllable superconducting islands in the Coulomb-blockaded regime. Our findings provide new insights into the dynamics of periodically driven interacting systems and highlight the robustness of Thouless pumping with respect to boundary effects typical of superconducting circuits.

OSNR enhancement of Rayleigh-assisted Brillouin-Raman fiber laser via double pass configuration.

We propose and demonstrate a 10 GHz spacing multi-wavelength Brillouin-Raman fiber laser (MBRFL) with wide bandwidth and an outstanding optical signal-to-noise ratio (OSNR). This is achieved by utilizing loop mirror at one end of the laser cavity through a symmetrical bi-directional Raman pumping scheme. The setup is arranged in a double pass configuration by employing different lengths of dispersion compensating fibers (DCF). The attainment of MBRFL with outstanding performance necessitates the optimization of Raman pump power, Brillouin pump wavelength, and DCF length. By employing an 11 km DCF, when setting the Brillouin pump wavelength at 1531.4 nm, 504 Stoke lines are produced with a channel spacing of 0.08 nm. All the counted laser lines have less than a 1-dB peak amplitude variation and are spread across a 40.4 nm bandwidth that covers from 1531.4 to 1571.8 nm wavelength. In this case, the Raman pump power is fixed at 900 mW which results in average OSNR and Stokes peak amplitude level of 28 dB and -7 dBm respectively. To date, this is the simplest cavity design with the widest bandwidth and flattest spectrum together with outstanding OSNR attained in 10 GHz spacing multi-wavelength fiber lasers that incorporate a single low-power Raman pump unit.

Simultaneous realization of high gain and low DMG of four-mode EDFA under bidirectional hybrid-mode pump.

We theoretically and experimentally verify that, the bidirectional hybrid-mode pumping scheme can address the optimization problem of trade-off between high gain and low differential modal gain (DMG) of four-mode erbium-doped fiber amplifier (4M-EDFA), in comparison with traditional both forward and backward hybrid-mode pumping scheme. It is noticed that, when the total pump power is fixed, the bidirectional hybrid-mode pumping scheme can not only achieve higher gain, but also suppress DMG due to different overlap integrals for the forward and backward pumping schemes. The bidirectional hybrid-mode pumped 4M-EDFA is developed with the forward pumping at LP02 mode and the backward pumping at LP21 mode, under a pump power ratio of 30%:70%. Thus, we can achieve an average gain of up to 21.16 dB and a low DMG of 0.43 dB at 1550 nm, and an average gain of up to 20.64 dB with a DMG of less than 1.6 dB over the C-band. In particular, the bidirectional hybrid-mode pumping scheme allows us to tailor the gain characteristics of the few-mode erbium-doped fiber amplifiers (FM-EDFAs), by adjusting the power ratio between forward and backward pumps.

Bandwidth extension to 1627 nm of over 20 dB gain in an erbium-doped silica fiber via two-photon absorption.

In this study, PbS/Er co-doped fibers (PEDFs) were fabricated by atomic layer deposition (ALD) combined with modified chemical vapor deposition (MCVD). A pumping scheme based on two-photon absorption at 1310 nm of PEDF is proposed for L + band amplification. Through the theoretical analysis, the local environment of Er3+ is changed due to the co-doping of PbS, which improves the two-photon absorption efficiency near 1300 nm. Compared with the 980 nm pump, the PEDFs excited by the 1310 nm pump show better amplification performance in the L + band. And in a bi-directional pumping system, PEDF achieves over 22 dB of gain in the whole L band. In particular, the bandwidth of over 20 dB gain was extended to 1627 nm with a noise figure as low as 4.9 dB. To the best of our knowledge, this is the first time that a high-gain bandwidth of L band amplification has been extended to 1627 nm. The results of unsaturated loss also show that PbS co-doping improves the two-photon absorption efficiency of PEDF to broaden the amplification bandwidth of L + band. These results demonstrate that an effective L + band amplification method is practically provided for future ultra-wideband optical communications.

IMPROVING THE PERFORMANCE INDICATOR OF CENTRIFUGAL PUMPS

This article is devoted to the research and development of methods to improve the performance of centrifugal pumps. Centrifugal pumps are key elements in various industrial and technical systems, ensuring efficient transportation of liquids. This article reviews the operation of centrifugal pumps, shows the scheme of the pumping part of the centrifugal type equipment, the scheme of the cantilever type centrifugal pump and describes their main components. Further, the factors affecting pump performance, including fluid viscosity and operating conditions, are analyzed, and methods for improving performance are described in detail, including design optimization, the use of new materials and modern technologies, as well as speed control and monitoring of pump condition. The advantages and disadvantages of centrifugal pumps are noted, the concept of what the operation of this equipment is based on is given, and the fields of application of centrifugal pumps are considered. In order to improve the operation of pumps, the article includes a table showing the existing problems in the operation of the pumps described by the author, the correction of which will lead to positive results, namely, an increase in quantitative and qualitative performance indicators. Further, in the article, a color diagram is shown, which shows the share distribution, that is, the percentage of damage to the structural elements of centrifugal pumps. To improve the reliability and efficiency of operation of centrifugal pumps, the article discusses in detail two ways to solve this task. The first way to solve the problem is the development and manufacture of new, namely more advanced pumps in design, which most often requires significant financial costs, and the second way was noted the modernization of already functioning equipment, which allows you to reduce your own costs and thereby ensure the implementation of energy saving programs. Based on the analysis and the examples considered, it is concluded that an increase in the performance of centrifugal pumps can lead to a significant improvement in efficiency and cost reduction. Keywords: centrifugal pump, productivity, performance indicators, optimization, materials, control.

Generation and characterization of polarization-entangled states using quantum dot single-photon sources

Single-photon sources based on semiconductor quantum dots find several applications in quantum information processing due to their high single-photon indistinguishability, on-demand generation, and low multiphoton emission. In this context, the generation of entangled photons represents a challenging task with a possible solution relying on the interference in probabilistic gates of identical photons emitted at different pulses from the same source. In this work, we implement this approach via a simple and compact design that generates entangled photon pairs in the polarization degree of freedom. We operate the proposed platform with single photons produced through two different pumping schemes, the resonant excited one and the longitudinal-acoustic phonon-assisted configuration. We then characterize the produced entangled two-photon states by developing a complete model taking into account relevant experimental parameters, such as the second-order correlation function, Hong–Ou–Mandel visibility, multiphoton emission and pump laser filtering. Our source shows long-term stability and high quality of the generated entangled states, thus constituting a reliable building block for optical quantum technologies.

High power tunable Raman fiber laser at 1.2 μm waveband

Development of a high power fiber laser at special waveband, which is difficult to achieve by conventional rare-earth-doped fibers, is a significant challenge. One of the most common methods for achieving lasing at special wavelength is Raman conversion. Phosphorus-doped fiber (PDF), due to the phosphorus-related large frequency shift Raman peak at 40 THz, is a great choice for large frequency shift Raman conversion. Here, by adopting 150 m large mode area triple-clad PDF as Raman gain medium, and a novel wavelength-selective feedback mechanism to suppress the silica-related Raman emission, we build a high power cladding-pumped Raman fiber laser at 1.2 μm waveband. A Raman signal with power up to 735.8 W at 1252.7 nm is obtained. To the best of our knowledge, this is the highest output power ever reported for fiber lasers at 1.2 μm waveband. Moreover, by tuning the wavelength of the pump source, a tunable Raman output of more than 450 W over a wavelength range of 1240.6–1252.7 nm is demonstrated. This work proves PDF’s advantage in high power large frequency shift Raman conversion with a cladding pump scheme, thus providing a good solution for a high power laser source at special waveband.Graphical

Multi-format all-optical modulating of microsphere resonator operating in O-band

We propose and demonstrate an all-optical tunable silica microsphere resonator based on a dual-laser pumping scheme. The resonance tunable microsphere resonator can act as a modulator and operates in the O-band. We discussed the relationship between the extinction ratio and pump power in different coupling state, and realized an extinction ratio over 15 dB. Also, we measured the rise and fall time of the modulated signal, which is below 1 μs, and discussed its relationship with the modulation frequency. In addition, based on this scheme, a multi-format modulation is realized for the first time with signals shaping in triangular, sinusoidal and square wave under different duty cycles. Our work reveals the detail of all-optical tunning of the resonance of the silica microresonator and opens up possible applications in optical communication, microwave photonics and quantum photonics.

Study on the combination of the annular jet pump and static mixer to improve the fluid‐carrying capacity of gas wells

AbstractAiming at the problem that the suction chamber of the gas‐driven jet pump has insufficient mixing of the power gas and the sucked fluid leading to efficiency reduction, this study proposes to effectively combine the static mixer with the annular jet pump and design a new type of annular jet pump and apply it to the gas wells to improve the fluid recovery capacity. Numerical simulations based on the gas–liquid two‐phase flow model are carried out for a conventional annular jet pump (CAJP) and a new annular jet pump (NAJP). The reliability of the simulation results is verified by gas–liquid two‐phase flow experiments, and the differences between the two in terms of velocity, pressure loss, and turbulent kinetic energy are analyzed. Meanwhile, the validity of NAJP is verified, and the effects of different structures such as static mixer torsion angle, suction chamber angle, and area ratio on the performance of NAJP are analyzed. The results show that NAJP enhances the degree of mixing between the sucked fluid and the power gas through the cyclonic effect created by the static mixer compared with CAJP. It results in a 10.6% year‐on‐year increase in the velocity of the sucked fluid, a 3% year‐on‐year increase in the pressure drop, and a 12.2% year‐on‐year increase in efficiency. NAJP can significantly improve the fluid‐carrying performance. With a mixer angle of 210°, a suction chamber angle of 21°, and an area ratio of 1.77, the NAJP achieves an efficiency of 39.7%, which is a year‐on‐year increase of 7.3% compared to the structure under the same conditions before optimization. This study lays a foundation for the determination of the optimal design scheme of the annular jet pump and at the same time can provide theoretical and technical support for researchers in related fields.

Flat supercontinuum spanning 738-2200 nm generation in standard telecom fibers based on dual-wavelength pumping scheme

Flat supercontinuum spanning 738-2200 nm generation in standard telecom fibers based on dual-wavelength pumping scheme