Pulsed Imaging Research Articles

Enhanced and robust contrast in CEST MRI: Saturation pulse shape design via optimal control.

To employ optimal control for the numerical design of Chemical Exchange Saturation Transfer (CEST) saturation pulses to maximize contrast and stability against inhomogeneities. We applied an optimal control framework for the design pulse shapes for CEST saturation pulse trains. The cost functional minimized both the pulse energy and the discrepancy between the corresponding CEST spectrum and the target spectrum based on a continuous radiofrequency (RF) pulse. The optimization is subject to hardware limitations. In measurements on a 7 T preclinical scanner, the optimal control pulses were compared to continuous-wave and Gaussian saturation methods. We conducted a comparison of the optimal control pulses with Gaussian, block pulse trains, and adiabatic spin-lock pulses. The optimal control pulse train demonstrated saturation levels comparable to continuous-wave saturation and surpassed Gaussian saturation by up to 50 % in phantom measurements. In phantom measurements at 3 T the optimized pulses not only showcased the highest CEST contrast, but also the highest stability against field inhomogeneities. In contrast, block pulse saturation resulted in severe artifacts. Dynamic Bloch-McConnell simulations were employed to identify the source of these artifacts, and underscore the robustness of the optimized pulses. In this work, it was shown that a substantial improvement in pulsed saturation CEST imaging can be achieved by using Optimal Control design principles. It is possible to overcome the sensitivity of saturation to B0 inhomogeneities while achieving CEST contrast close to continuous wave saturation.

Evaluation of static bending caused damage of glass-fiber composite structure using terahertz inspection

Abstract Composite materials find increasing applications in modern industry and transport. However, they may lose desirable mechanical properties due to external mechanical excitations, ultraviolet radiation, moisture penetration, or other factors. Therefore, an effective way to assess the condition of materials is necessary. In this article, a nondestructive evaluation of glass fiber-reinforced composite subjected to five-stage static bending is presented. For this reason, pulsed excitation terahertz imaging was utilized, and a data processing/exploration scheme was proposed. The proposed, novel approach consists of an efficient data registration algorithm based on surface approximation (for surface roughness and unevenness elimination) and a parametrization scheme applied for the signals gained from the time response of the glass fiber-reinforced polymer layer. Obtained parameters enable the global description of the evaluated material state and prediction of failure effectively, even in the early stages of destruction.

Time Interval Between Right Ventricular Early Diastolic Velocity by Tissue and Pulse Wave Doppler: An Index of Right Atrial Pressure in Pulmonary Hypertension Patients

Background: A reversal of time difference between the onset of early diastolic velocity (e’) during tissue Doppler imaging and the onset of mitral inflow (E) has been observed in cases of elevated left atrial pressure. Whether this interval (Te’-E) may be useful to assess right atrial pressure has never been investigated, neither in healthy subjects nor in pulmonary hypertension patients. Methods: Right ventricular Te’-E was assessed in patients with pre-capillary pulmonary hypertension and compared with healthy volunteers who underwent comprehensive echocardiography examination. Te’-E is the difference between the interval from R wave at the superimposed electrocardiogram to the e’ wave during right ventricular tissue Doppler imaging and the interval from the R wave to transtricuspid E wave during pulsed wave Doppler imaging. Right atrial pressure was invasively measured in pulmonary hypertension patients. Results: Fifty-six patients were enrolled. Te’-E was prolonged in pulmonary hypertension subjects compared with healthy subjects (p < 0.001). Amongst the pulmonary hypertension patients, strong correlations were found between Te’-E and right atrial pressure (r = −0.885, p < 0.001), systolic pulmonary pressure (r = −0.85, p < 0.001) and the duration of tricuspid regurgitation (r = 0.72, p < 0.001). The area under the receiver operating characteristic curve of Te’-E in identifying right atrial pressure higher than 15 mm of mercury was 0.992 (sensitivity 100%, specificity 83%). Conclusions: In contrast to the left ventricle, there is a delay in the proto-diastolic filling in pulmonary hypertension patients, which correlates with the increase in systolic pulmonary arterial pressure, right atrial pressure, tricuspid regurgitation duration and restrictive diastolic pattern.

31P multi-echo MRSI with low B1 + dual-band refocusing RF pulses.

31P magnetic resonance spectroscopy (MRS) can spectrally resolve metabolites involved in phospholipid metabolism whose levels are altered in many cancers. Ultra-high field facilitates the detection of phosphomonoesters (PMEs) and phosphodiesters (PDEs) with increased SNR and spectral resolution. Utilizing multi-echo MR spectroscopic imaging (MRSI) further enhances SNR and enables T2 information estimation per metabolite. To address the specific absorption rate (SAR) challenges associated with high-power demanding adiabatic or composite block pulses in multi-echo phosphorus imaging, we present a dual-band refocusing RF pulse designed for operation at B1 amplitudes of 14.8 μT which holds potential for integration into multi-echo sequences. Phantom and in vivo experiments conducted in the brain at 7Tesla validated the effectiveness of this low-power dual-band RF pulse. Furthermore, we implemented the dual-band RF pulse into a multi-echo MRSI sequence where it offered the potential to increase the number of echo pulses within the same acquisition time compared to high-power adiabatic implementation, demonstrating its feasibility and practicality.

Physicochemical and digestive properties of curcumin stabilized by quaternized chitosan/sodium alginate nanoemulsion coatings

Curcumin (Cur) is a bioactive substance, but its instability limits its use in the food system. Thus, a new polysaccharide-based coating is developed by combining quaternized chitosan (QCS) with sodium alginate (SA) in this study to improve the bioaccessibility and stability of Cur. The microstructure of the emulsion was characterized by fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and low-field pulsed nuclear magnetic resonance imaging (LF-NMR). The thermal, ionic strength, and pH stability of emulsions were measured. Results indicate that QCS/SA (1:1)-Cur is more stable than other three nanoemulsion systems and the encapsulation rate of which reaches 90.62 %. It also shows higher stability in gastric fluid, excellent bioaccessibility and FFAs in intestinal fluid, as well as significant antibacterial property, antioxidant activity and water dispersibility. This study introduces a new method for obtaining stable, functional Cur-coated systems for food applications.

Scan-Specific Unsupervised Highly Accelerated Non-Cartesian CEST Imaging Using Implicit Neural Representation and Explicit Sparse Prior.

Chemical exchange saturation transfer (CEST) is a promising magnetic resonance imaging (MRI) technique. CEST imaging usually requires a long scan time, and reducing acquisition time is highly desirable for clinical applications. A novel scan-specific unsupervised deep learning algorithm is proposed to accelerate steady-state pulsed CEST imaging with golden-angle stack-of-stars trajectory using hybrid-feature hash encoding implicit neural representation. Additionally, imaging quality is further improved by using the explicit prior knowledge of low rank and weighted joint sparsity in the spatial and Z-spectral domain of CEST data. In the retrospective acceleration experiment, the proposed method outperforms other state-of-the-art algorithms (TDDIP, LRTES, kt-SLR, NeRP, CRNN, and PBCS) for the in vivo human brain dataset under various acceleration rates. In the prospective acceleration experiment, the proposed algorithm can still obtain results close to the fully-sampled images. The hybrid-feature hash encoding implicit neural representation combined with explicit sparse prior (INRESP) can efficiently accelerate CEST imaging. The proposed algorithm achieves reduced error and improved image quality compared to several state-of-the-art algorithms at relatively high acceleration factors. The superior performance and the training database-free characteristic make the proposed algorithm promising for accelerating CEST imaging in various applications.

Structural Effects on the Energy Disposal and Atomic Photofragment Alignment for the Photodissociation of Alkyl Iodides at Excitation Wavelengths of 254 and 268 nm.

This work represents a step forward in the understanding of the widely studied photodynamics of alkyl iodides in the first absorption band. Ultraviolet (UV) photodissociation of several alkyl iodides (RI), specifically, a series of linear and ramified molecules with R = CnH2n+1, n = 1-4, at excitation wavelengths of 254 and 268 nm, which correspond to the maximum of the first absorption A-band, has been studied by combining resonance-enhanced multiphoton ionization (REMPI) detection of atomic photofragments I(2P3/2) and I*(2P1/2) and of pulsed slice imaging. Detailed examination of the total translational energy distributions of both atomic photofragments has been combined with stereodynamical information on the process obtained from the anisotropy β and alignment a02(∥) and Re[a12(∥, ⊥)] parameters to provide a description of the role played by the molecular structure of alkyl iodides in adiabatic and, especially, in nonadiabatic photodissociation dynamics through conical intersections or avoided crossings. The present results suggest that the linear structures couple more efficiently with the pure C-I reaction coordinate, whereas for the branched structures, the coupling with additional vibrational (bending) modes gains importance, showing the dissociation process a multidimensional character. In addition, a large degree of cofragment rotational alignment has been found for the small linear CH3I and C2H5I and, unexpectedly, for the branched t-C4H9I (C3v symmetry), whereas the rest of the alkyl iodides show low alignment parameters.

A portable multi-taxa phenotyping device to retrieve physiological performance traits

Organismal phenotyping to identify fitness traits is transforming our understanding of adaptive responses and ecological interactions of species within changing environments. Here we present a portable Multi-Taxa Phenotyping (MTP) system that can retrieve a suite of metabolic and photophysiological parameter across light, temperature, and/or chemical gradients, using real time bio-optical (oxygen and chlorophyll a fluorescence) measurements. The MTP system integrates three well-established technologies for the first time: an imaging Pulse Amplitude Modulated (PAM) chlorophyll a fluorometer, custom-designed well plates equipped with optical oxygen sensors, and a thermocycler. We demonstrate the ability of the MTP system to distinguish phenotypic performance characteristics of diverse aquatic taxa spanning corals, mangroves and algae based on metabolic parameters and Photosystem II dynamics, in a high-throughput capacity and accounting for interactions of different environmental gradients on performance. Extracted metrics from the MTP system can not only provide information on the performance of aquatic taxa exposed to differing environmental gradients, but also provide predicted phenotypic responses of key aquatic organisms to environmental change. Further work validating how rapid phenotyping tools such as the MTP system predict phenotypic responses to long term environmental changes in situ are urgently required to best inform how these tools can support management efforts.

Ultrasonographic assessment of the fetal heart in intrahepatic cholestasis of pregnancy: Pulsed wave Doppler, M-mode, and tissue Doppler imaging prospective study.

To investigate the fetal heart using pulsed wave Doppler, M-mode, and tissue Doppler imaging (TDI) in cases of intrahepatic cholestasis of pregnancy (ICP). This prospective study was conducted at a single tertiary center and included 35 patients with ICP and 70 healthy pregnant women at 28-36 weeks of pregnancy. Among the patients with ICP, 26 had serum bile acid (SBA) levels less than 40 μmol/L and nine had SBA levels of 40 μmol/L or greater. Pulsed wave Doppler, M-mode, and TDI evaluations were performed on the patients to assess fetal cardiac function. The ICP group exhibited significantly higher myocardial performance index (MPI) and isovolumetric relaxation time (IRT), but similar isovolumetric contraction time (ICT). The tricuspid and mitral valve E, A, and E/A ratios were significantly reduced in the ICP group. The TDI parameters showed significantly reduced tricuspid and mitral valve E'/A' ratios in the ICP group compared with the control group (P < 0.001). The E/E' ratio was significantly increased in the ICP group (P < 0.001). According to the M-mode Doppler findings, tricuspid and mitral annular plane systolic excursion values were significantly decreased in the ICP group (P = 0.005 and P = 0.001, respectively). In the subgroup analysis, MPI and IRT were significantly higher in the severe ICP group. ICP might induce changes in the fetal heart during the early systolic and diastolic phases. The detection of these early changes using M-mode and TDI during the antenatal period can provide valuable insights into the condition of the fetus.

A Radiological Clip Design Using Ultrasound Identification to Improve Localization.

We demonstrate the use of ultrasound to receive an acoustic signal transmitted from a radiological clip designed from a custom circuit. This signal encodes an identification number and is localized and identified wirelessly by the ultrasound imaging system. We designed and constructed the test platform with a Teensy 4.0 microcontroller core to detect ultrasonic imaging pulses received by a transducer embedded in a phantom, which acted as the radiological clip. Ultrasound identification (USID) signals were generated and transmitted as a result. The phantom and clip were imaged using an ultrasonic array (Philips L7-4) connected to a Verasonics™ Vantage 128 system operating in pulse inversion (PI) mode. Cross-correlations were performed to localize and identify the code sequences in the PI images. USID signals were detected and visualized on B-mode images of the phantoms with up to sub-millimeter localization accuracy. The average detection rate across 30,400 frames of ultrasound data was 98.1%. The USID clip produced identifiable, distinguishable, and localizable signals when imaged. Radiological clips are used to mark breast cancer being treated by neoadjuvant chemotherapy (NAC) via implant in or near treated lesions. As NAC progresses, available marking clips can lose visibility in ultrasound, the imaging modality of choice for monitoring NAC-treated lesions. By transmitting an active signal, more accurate and reliable ultrasound localization of these clips could be achieved and multiple clips with different ID values could be imaged in the same field of view.

Design of Ultra-Narrow Bandgap Polymer Acceptors for High-Sensitivity Flexible All-Polymer Short-Wavelength Infrared Photodetectors.

All-polymer photodetectors possess unique mechanical flexibility and are ideally suitable for the application in next-generation flexible, wearable short-wavelength infrared (SWIR, 1000-2700 nm) photodetectors. However, all-polymer photodetectors commonly suffer from low sensitivity, high noise, and low photoresponse speed in the SWIR region, which significantly diminish their application potential in wearable electronics. Herein, two polymer acceptors with absorption beyond 1000 nm, namely P4TOC-DCBT and P4TOC-DCBSe, were designed and synthesized. The two polymers possess rigid structure and good conformational stability, which is beneficial for reducing energetic disorder and suppressing dark current. Owing to the efficient charge generation and ultralow noise current, the P4TOC-DCBT-based all-polymer photodetector achieved a specific detectivity () of over 1012 Jones from 650 (visible) to 1070 nm (SWIR) under zero bias, with a response time of 1.36 μs. These are the best results for reported all-polymer SWIR photodetectors in photovoltaic mode. More significantly, the all-polymer blend films exhibit good mechanical durability, and hence the P4TOC-DCBT-based flexible all-polymer photodetectors show a small performance attenuation (<4%) after 2000 cycles of bending to a 3 mm radius. The all-polymer flexible SWIR organic photodetectors are successfully applied in pulse signal detection, optical communication and image capture.

Design of Ultra‐Narrow Bandgap Polymer Acceptors for High‐Sensitivity Flexible All‐Polymer Short‐Wavelength Infrared Photodetectors

All‐polymer photodetectors possess unique mechanical flexibility and are ideally suitable for the application in next‐generation flexible, wearable short‐wavelength infrared (SWIR, 1000–2700 nm) photodetectors. However, all‐polymer photodetectors commonly suffer from low sensitivity, high noise, and low photoresponse speed in the SWIR region, which significantly diminish their application potential in wearable electronics. Herein, two polymer acceptors with absorption beyond 1000 nm, namely P4TOC‐DCBT and P4TOC‐DCBSe, were designed and synthesized. The two polymers possess rigid structure and good conformational stability, which is beneficial for reducing energetic disorder and suppressing dark current. Owing to the efficient charge generation and ultralow noise current, the P4TOC‐DCBT‐based all‐polymer photodetector achieved a specific detectivity () of over 1012 Jones from 650 (visible) to 1070 nm (SWIR) under zero bias, with a response time of 1.36 μs. These are the best results for reported all‐polymer SWIR photodetectors in photovoltaic mode. More significantly, the all‐polymer blend films exhibit good mechanical durability, and hence the P4TOC‐DCBT‐based flexible all‐polymer photodetectors show a small performance attenuation (&lt;4%) after 2000 cycles of bending to a 3 mm radius. The all‐polymer flexible SWIR organic photodetectors are successfully applied in pulse signal detection, optical communication and image capture.

Linear Bloch-Siegert phase-encoded low-field MRI: RF coils, pulse sequence, and image reconstruction.

Conventional gradient systems have several weaknesses including high cost and bulk. As a step towards addressing these while providing new degrees of freedom for spatial encoding and system design in Magnetic Resonance Imaging (MRI), a radio frequency (RF) gradient encoding system and pulse sequence for phase encoding using the Bloch-Siegert (BS) shift were developed. Optimized BS spatial encoding coils with bucking windings (counter-wound loops) were designed and constructed, along with compatible homogeneous imaging coils for excitation and signal reception. Two coil systems were developed: one for phantom imaging and a second for human wrist imaging. BS phase-encoded imaging and BS RF pulse simulations were performed. Pulse sequences were designed for linear stepping in k-space and implemented on a 47.5-mT scanner to image resolution phantoms in both coil setups. Reconstructions were performed using both the full -based encoding fields for each BS pulse amplitude and using inverse discrete Fourier transforms. A gradient was used for frequency encoding during signal readout, and the third axis was projected. Specific absorption ratio (SAR) calculations were performed for the wrist coil to determine the safety of BS-based RF encoding for fields in the low field MRI regime. The optimized RF spatial encoding coils resulted in higher linearity ( and 0.9921 in the phantom and wrist coils, respectively) than coils used in previous work. The phantom and wrist imaging coils were validated in simulations and experimentally to produce a peak G and 0.8 G with 12-W input power, respectively, in the field-of-view (length = 11 cm) used for imaging. Nominal imaging resolutions of 5.22 and 7.21 mm were, respectively, achieved by the two-coil systems in the RF phase-encoded dimension. Coil systems, pulse sequences, and image reconstructions were developed for linear RF phase encoding using the BS shift and validated using a 47.5-mT open low field scanner, establishing a key component required for gradient-free imaging at low field strengths.

Flow structures in large-scale bank erosion zone of Lower Yangtze River

The bank erosion process in the densely populated Lower Yangtze River can pose a great threat to riparian residents and industries. It is characterized by rapid development within a few hours, a large-scale soil collapse of 106 m3, and an arc shape. During its development, flow field inside the bank erosion area continuously evolves and interacts with the bank soil. However, the mechanisms behind the bank erosion process are still unclear. Therefore, laboratory experiments were conducted to investigate flow structures and turbulences inside bank erosion areas. A pulsed particle image velocimeter was employed to obtain high-quality velocity data inside the bank erosion zone. Results show that the bank erosion zone can be divided into a backflow zone, a mixing zone, and a mainstream zone, according to variations in flow structure; in the mixing zone, water flow is highly turbulent, and the mixing width gradually increases downstream because of the shear effects between the mainstream and backflow; the backflow zone can be subdivided into a central zone and a peripheral zone, based on the pattern of velocity changes along the radial axis from the backflow center to its periphery. A formula for calculating the flow velocity within the backflow zone was proposed, and we found that the velocity gradient in the peripheral zone was approximately four times higher than that in the central zone. This indicated that shear stress exerted by the flow near the backflow boundary was significantly intensified.

Impact of immediate release film coating on the disintegration process of tablets

Pharmaceutical tablets are often coated with a layer of polymeric material to protect the drug from environmental degradation, facilitate the packaging process, and enhance patient compliance. However, the detailed effects of such coating layers on drug release are not well understood. To investigate this, flat-faced pure microcrystalline cellulose tablets with a diameter of 13 mm and a thickness between 1.5 mm to 1.6 mm were directly compressed, and a film coating layer with a thickness of 80 μm to 120 μm was applied to one face of these tablets. This tablet geometry and immediate release film coating were chosen as a model system to understand how the film coating interacts with the tablet core. The coating hydration and dissolution process was studied using terahertz pulsed imaging, while optical coherence tomography was used to capture further details on the swelling process of the polymer in the coated tablet. The study investigated the film coating polymer dissolution process and found the gelling of dissolving polymer restricted the capillary liquid transport in the core. These findings can help predict the dissolution of film coating within the typical range of thickness (30 μm to 40 μm) and potentially be extended to understand modified release coating formulations.

Demonstration of chirped pulse phase-shifting digital holography for capturing the sequence of ultrafast optical wavefronts

We experimentally demonstrate chirped pulse phase-shifting digital holography. This method, recently proposed, allows for capturing the sequence of ultrafast optical wavefronts with picosecond time resolution in a single-shot manner. In our experiment, we recorded two object pulses with a time separation of 1.67 ps using 35-fs-width optical pulses, employing a diffractive optical element and a bandpass filter, on a single polarization camera simultaneously. We reconstructed both the intensity and phase images of these object pulses using modified calculations that account for corrections in the polarization states of the reference waves, thereby improving the quality of the reconstructed images.

Tuned exchange imaging: Can the filter exchange imaging pulse sequence be adapted for applications with thin slices and restricted diffusion?

Filter exchange imaging (FEXI) is a double diffusion-encoding (DDE) sequence that is specifically sensitive to exchange between sites with different apparent diffusivities. FEXI uses a diffusion-encoding filtering block followed by a detection block at varying mixing times to map the exchange rate. Long mixing times enhance the sensitivity to exchange, but they pose challenges for imaging applications that require a stimulated echo sequence with crusher gradients. Thin imaging slices require strong crushers, which can introduce significant diffusion weighting and bias exchange rate estimates. Here, we treat the crushers as an additional encoding block and consider FEXI as a triple diffusion-encoding sequence. This allows the bias to be corrected in the case of multi-Gaussian diffusion, but not easily in the presence of restricted diffusion. Our approach addresses challenges in the presence of restricted diffusion and relies on the ability to independently gauge sensitivities to exchange and restricted diffusion for arbitrary gradient waveforms. It follows two principles: (i) the effects of crushers are included in the forward model using signal cumulant expansion; and (ii) timing parameters of diffusion gradients in filter and detection blocks are adjusted to maintain the same level of restriction encoding regardless of the mixing time. This results in the tuned exchange imaging (TEXI) protocol. The accuracy of exchange mapping with TEXI was assessed through Monte Carlo simulations in spheres of identical sizes and gamma-distributed sizes, and in parallel hexagonally packed cylinders. The simulations demonstrate that TEXI provides consistent exchange rates regardless of slice thickness and restriction size, even with strong crushers. However, the accuracy depends on b-values, mixing times, and restriction geometry. The constraints and limitations of TEXI are discussed, including suggestions for protocol adaptations. Further studies are needed to optimize the precision of TEXI and assess the approach experimentally in realistic, heterogeneous substrates.

Classification of Multi-Source Partial Discharge in GIS

Abstract Partial discharge (PD) analysis is an important method to identify electrical equipment faults. However, due to the influence of environmental electromagnetic interference and other equipment discharges in the power supply circuit during the on-site PD test, the collected PD signal is the combination of various PD and noise, which makes it challenging to identify the type or source of on-site partial discharge. A multi-source PD classification method based on the multiple threshold and K-means clustering algorithm is pro-posed to solve this problem. First, wavelet transform with an improved threshold is used to initially denoise the original signal. Then the multiple threshold method is used to filter the residual ripple between every two pulses. Finally, spectrum analysis is carried out for each pulse, and the maximum value of the spectrum is extracted as the feature quantity. Then, the K-means algorithm is used to classify the PD pulses, and the PRPD images of PD pulses in different frequency domains are obtained. The results show that the method adopted in this paper can denoise, extract and classify the PD signals collected on the site, and the PRPD diagram of PD pulse after classification is more obvious, which provides a basis for identifying the PD source on the site.

THz vs NIR laser-assisted atom probe tomography of LaB6 samples

Terahertz (THz) radiation with low-energy photons (meV) is used in a wide range of applications, such as microscopy, sensing, and spectroscopy. However, recently, high amplitude THz pulses of MV/cm have been generated and used for electron emission and ion evaporation from field emitters, opening up the possibility of using high amplitude THz pulses for material imaging by THz-assisted atom probe tomography (APT). In this work, we compare the APT analyses of lanthanum hexaboride (LaB6) samples using a femtosecond near-infrared laser with those obtained using high-amplitude single-cycle THz pulses. The atomic-scale characterization of stoichiometric LaB6 is challenging in laser-assisted APT due to the detection losses of boron ions. Here, we show that the THz radiation reduces the emission of molecular ions and multiple detection events, and it increases the charge state of the emitted ions. All these effects result in an improvement in boron detection. Furthermore, the emission dynamics of boron and lanthanum ions differ in their evaporation times when using THz radiation. This work emphasizes the ability of high-amplitude, single-cycle THz pulses to well control material analysis in APT, leading to better results on chemical composition. It also paves the way for the use of this radiation for material manipulation.

An electroporation cytometry system for long-term, live cell cycle analysis.

Electric fields are used in biology to address a broad range of questions and through a variety of techniques, including electroporation, gene electrotransfer (GET), electrostimulation (ES), and electrochemotherapy. Each of these modalities requires specific conditions and has drastically different target outcomes on the cell. ES has demonstrated that non-pore forming electric fields alter cell cycle progression. However, pore forming electric fields such as with GET have not been as widely explored despite major clinical advancements. Additionally, the real-time visual analysis of electrical field effects on mammalian cell culture is currently lacking among most commercial systems. To facilitate investigations into these research areas, an electroporation cytometry system was developed including a custom chamber compatible with live cell imaging and exponential decay pulse generator for live cell analysis. The functionality of the system was demonstrated using a recombinant cell line using U-2 OS cells and FUCCI(CA)5 cell cycle reporter. The exposure of the cells to a 180 V pulse in both unsynchronized and synchronized populations revealed an effect on the cell cycle.