Pull-out Force Research Articles

Opposing Flanks vs Parallel Flanks – the Influence of Headless Screw Design on Compression and Pull- Out Resistance

Category: Basic Sciences/Biologics; Basic Sciences/Biologics Introduction/Purpose: Screws generate and maintain compression against distracting forces when performing osteotomy or fusion surgery. Headless screws with opposing flank angles (OFA) between the threads of the head and shaft are purported to achieve better compression. The purpose of this study was to compare OFA designs against traditional parallel flank angle (PFA) headless screws and headed screws to determine differences in compression and pull-out resistance (POR). Methods: In this biomechanical in-vitro study, four screw designs were compared: headless screws with OFA (Screw_A and Screw_B), headless screws with PFA (Screw_C), and headed screws (Screw_D). All screws were 4.0x50mm partially threaded cannulated screws. Screw_B had a 1.4mm shorter head length and 0.5mm narrower head thread diameter than Screw_A and Screw_C, which were similar. A custom apparatus was designed for measuring compression and POR. Osteotomies were created on synthetic bone blocks (density 0.32g/cm3) simulating cancellous bone. Screws were inserted perpendicular to osteotomies in accordance with manufacturer guidance and maximum compression recorded. Increasing distracting forces were then applied to the blocks until the screws pulled out. For each screw type, five screws were tested. Results: There was no significant difference in maximum compression between screw designs: Screw_A=38.7N±14.2N, Screw_B=48.7N±15.6N, Screw_C=51.9N±36.4N, Screw_D=32.0N±9.2N; p=0.921. When assessing POR, all screws failed at the head-bone interface (screw heads subsided into block). Pull-out forces significantly differed between all groups: Screw_A=466N±29.0N, Screw_B=310N±22.0N, Screw_C=399N±46.0N, Screw_D=183N±12.9N; p< 0.001 (ANOVA). Screw_Ahad the highest POR but the other OFA design (Screw_B) had significantly lower POR. Conclusion: Screw design, whether headless (OFA or PFA) or headed did not appear to influence compression generated. However, headed screws had significantly lower POR than headless designs. Within headless designs, OFA may increase POR, but other screw head features (number / diameter of threads) had an apparently greater influence than flank angle.

Largely improved interfacial adhesion and fatigue life of aramid fiber/polymer composites by developing GO enhanced eco-friendly dip-coating system

For achieving high performance and long fatigue life of fiber-reinforced polymer composites (FRPC), a key is to construct strong interfacial bonding between fibers and polymer. Herein, an epoxy resin-based environmentally friendly dipping solution (named as MGL) for aramid fiber (AF) was newly designed and produced to obtain the same good interfacial bonding with natural rubber (NR) as that using traditional toxic resorcinol–formaldehyde-rubber latex (RFL). The H pull-out force and fatigue life of AF/NR composites treated by using the new MGL dipping system are even higher than that using RFL. Based on the theory of interface stress transfer, polyethyleneimine (PEI) modified graphene oxide (GO) was further introduced into the new dipping system, and the H pull-out force, 180° peel-out force and fatigue life of AF/NR composites largely increase by 23.8%, 26.7% and 60.7%, respectively. The H pull-out force of AF/NR composites is significantly higher than that reported in previous studies.

IMPACT OF THE GLUE LAYER PROPERTIES ON THE STRESS-STRAIN STATE OF THE GLUE ANCHOR FOR THE STEEL ROD IN CONCRETE

The article deals with the distribution of stresses and displacements along a steel anchor fixed in concrete with a polymer binder - an acrylic compound. It was established that the maximum values of tangential, radial, and circular stresses, which more fully characterize the operation of the connection, change depending on the strength characteristics of the adhesive layer and its thickness according to the exponential law. The obtained results of stress at any point of the adhesive joint allow us to propose a methodology for the design of steel rods in concrete fixed with polymers. As a result of solving the problem of the stressed-strained state of the anchor connection on acrylic adhesives, equations were obtained for determining stresses and strains at any point. As a result of the analysis of the obtained dependencies, the following conclusions can be drawn. When calculating the strength of anchor joins on acrylic adhesives, it is necessary to take into account the maximum values of tangential, radial, and circular stresses. In order to calculate the strength of the join, it is necessary to know the strength limit at uniform separation of the glue from the metal surface, as well as at shear for the glue-metal contact. Tangential and normal stresses in the adhesive cylinder and at the adhesive-concrete interface decrease with an increase in the modulus of elasticity of the acrylic adhesive. But this leads to an increase in normal axial stresses in the part of the anchor embedded in concrete and radial stresses at the glue-anchor and glue-concrete contacts. The elasticity modulus of the glue layer is smaller than the elasticity modulus of concrete and metal. Therefore, the adhesive distributes the stresses that arise from the application of the pull-out force between the anchor and the concrete massif. This is explained by the fact that the pull-out stresses from the anchor are completely transferred to the adhesive layer and then to the concrete. The main vector of tangential stresses does not depend on the ratios of the elasticity modulus of the materials which form the anchor join. The thickness of the adhesive layer has a slight effect on the stress in the glue-anchor contact, but significantly on the stress in the glue-concrete contact.

Plate fixation optimization for distal femoral fractures with segmental bone loss: Defining the preferred screw distribution using finite element analysis

ObjectivesDistal femur fractures can exhibit extensive comminution, and open fractures may result in bone loss. These injuries are under high mechanical demands when stabilized with a lateral locked plate (LLP), and are at risk of non-union or implant failure. This study investigates the optimal LLP screw configuration for distal femur fractures with a large metadiaphyseal gap of 5 cm. MethodsA finite element (FE) model, validated against experimentally measured strains and displacement, evaluated pull-out forces and stress concentration on typical implants under clinical conditions corresponding with the 10 % point during the stance phase of the gait cycle. ResultsMaximum stress was up to 83 % less when the ratio (Cp) between the proximal screw-distribution-length and the distance of the first screw to the fracture was less than 0.2; maximum pull-out force was 99 % less when this ratio was higher than 0.4. ConclusionsScrew configuration based on either normal or osteopenic bone quality plays an important role in determining the risk of construct failure for a major (50 mm) distal femoral metadiaphyseal segmental defect. This study provides valuable information when planning definitive fixation for distal femur fractures with extensive comminution or segmental bone defects, to mitigate the risk of implant failure and subsequent nonunion.

Pre-clinical characterization of a novel flexible surface stem design for total knee replacements.

Primary stability is crucial for implant osseointegration and the long-term stability of cementless total joint replacements. Biomechanical studies have shown the potential of femoral stems for total knee replacements to reduce micromotions at the bone-implant interface. However, approaches such as focusing on the structural elasticity of the femoral stems are rarely described. Three groups with different femoral stem designs were investigated: group 1: flexible surface stem, group 2: flexible surface stem with open-porous structured lamellas, and group 3: solid stem (reference). The stems were implanted into bone substitute material and dynamically loaded for 1000 cycles. Relative movement and subsidence were measured optically, and axial pull-out forces were determined after dynamic testing. Relative movements increased to 0.10 mm (groups 1 and 2) compared to 0.03 mm (group 3). Subsidence increased to 0.08 mm (group 1) and 0.11 mm (group 2) compared to 0.06 mm (group 3). For each group, subsidence mainly occurred during the first 500 cycles. A similar convergence was observed in the further course. Pull-out forces increased to 1815.0 N (group 1) and 1347.1 N (group 2) compared to 1306.4 N (group 3). The flexible surface stem design resulted in higher relative movements and subsidence, but also exhibited increased pull-out forces. The relative movements were below the critical limit of 0.15 mm and represent a superposition of the elastic deformations of the interacting implant components as well as the micromotion at the bone-implant interface. Therefore, the novel flexible surface stem design appears to offer promising primary implant fixation.

Mechanical properties evaluation of metacarpophalangeal joint prosthesis with new titanium-nickel memory alloy: a cadaver study

ObjectiveNi-Ti memory alloys are unusual materials for hard-tissue replacement because of their unique superelasticity, good biocompatibility, high strength, low specific gravity, low magnetism, wear resistance, corrosion resistance and fatigue resistance. The current study aims to evaluate its mechanical properties and provide biomechanical basis for the clinical application of the prosthesis.MethodsTen adult metacarpophalangeal joint specimens were randomly divided into a prosthesis group (n = 5, underwent metacarpophalangeal joint prosthesis) and a control group (n = 5, underwent sham operation). Firstly, the axial compression strength was tested with BOSE material testing machine to evaluate its biomechanical strength. Secondly, these specimens were tested for strain changes using BOSE material testing machine and GOM non-contact optical strain measurement system to evaluate the stress changes. Thirdly, fatigue test was performed between groups. Lastly, the mechanical wear of the metacarpophalangeal joint prosthesis was tested with ETK5510 material testing machine to study its mechanical properties.ResultsAxial compression stiffness in the prosthesis group was greater than that in the control group in terms of 30 ° and 60 ° flexion positions (P < 0.05). There was no statistically significant difference between two groups with regards to axial compression stiffness and stress change test (P > 0.05). In the fatigue wear test, the mean mass loss in the prosthesis group’s prosthesis was 17.2 mg and 17.619 mm3, respectively. The mean volume wear rate was 0.12%. There was no statistically significant difference in the maximum pull-out force of the metacarpal, phalangeal, and polymer polyethylene pads between the prosthesis group and the control group specimens.ConclusionsNi-Ti memory alloy metacarpophalangeal joint prosthesis conforms to the biomechanical characteristics of metacarpophalangeal joints without implants, and the fatigue strength can fully meet the needs of metacarpophalangeal joint activities after joint replacement.

Study of interwall interaction during the pull separation of ultra-long double-walled carbon nanotubes under lateral loading

The successful fabrication of ultra-long carbon nanotubes (CNTs) makes CNTs ideal candidates for bearing systems due to the long sliding distance with low interwall interaction. However, it is difficult to measure the pull-out forces of ultra-long CNTs along their axes in real-time because of the difficulty of performing long-distance pull-out experiments. In this study, we proposed a lateral loading method to measure the interwall interaction force of ultra-long CNTs. By using a theoretical model and multi-scale finite element simulations, we could predict the interwall interaction force from the pull-out force in lateral loading. This pull-out force depends on the length of CNTs, and a critical length divides the pull-out force into two categories: maximum pull-out force due to local buckling and steady pull-out force due to sliding. In order to correctly measure the interwall interaction force by lateral loading, for the DWCNTs with the outer tube diameter of 0.955 nm, we have to make sure the lengths are greater than this critical value (54.2 nm) as experimental subjects.

Cohesive Zone Modeling of Pull-Out Test for Dental Fiber-Silicone Polymer.

Several analytical methods for the fiber pull-out test have been developed to evaluate the bond strength of fiber-matrix systems. We aimed to investigate the debonding mechanism of a fiber-silicone pull-out specimen and validate the experimental data using 3D-FEM and a cohesive element approach. A 3D model of a fiber-silicone pull-out testing specimen was established by pre-processing CT images of the typical specimen. The materials on the scans were posted in three different cross-sectional views using ScanIP and imported to ScanFE in which 3D generation was implemented for all of the image slices. This file was exported in FEA format and was imported in the FEA software (PATRAN/ABAQUS, version r2) for generating solid mesh, boundary conditions, and material properties attribution, as well as load case creation and data processing. The FEM cohesive zone pull-out force versus displacement curve showed an initial linear response. The Von Mises stress concentration was distributed along the fiber-silicone interface. The damage in the principal stresses' directions S11, S22, and S33, which represented the maximum possible magnitude of tensile and compressive stress at the fiber-silicone interface, showed that the stress is higher in the direction S33 (stress acting in the Z-direction) in which the lower damage criterion was higher as well when compared to S11 (stress acting in the XY plane) and S23 (stress acting in the YZ plane). The comparison between the experimental values and the results from the finite element simulations show that the proposed cohesive zone model accurately reproduces the experimental results. These results are considered almost identical to the experimental observations about the interface. The cohesive element approach is a potential function that takes into account the shear effects with many advantages related to its ability to predict the initiation and progress of the fiber-silicone debonding during pull-out tests. A disadvantage of this approach is the computational effort required for the simulation and analysis process. A good understanding of the parameters related to the cohesive laws is responsible for a successful simulation.

Olecranon fractures: A biomechanical comparison of three tension band wiring fixation methods on bone models.

This study aimed to compare the biomechanical pull-out strength of the three different tension band wiring (TBW) methods employed to fix transverse olecranon fractures on bone models. Three different fixation models were created in groups of seven synthetic olecranon fractured bone models. The first technique was fixed the olecranon with the traditional TBW method. The second technique was fixed the olecranon with a large intramedullary screw TBW method. The third technique was fixed the olecranon with the double-screw TBW method. The pull-out force needed for the failure of each specimen under the tensile test device was evaluated, and the results were recorded. We found that the lowest average pull out strength was 55.10N (range: 35.87-65.85 ± 10.17) in the traditional TBW method, the highest pull out strength was 84.28N (range: 63.67-117 ± 18.87) in the double-screw TBW method. The pull out strength was 70.80N (range: 52.60-80.95 ± 10.18) in the intramedullary screw TBW method. In terms of ultimate failure loads, there was no significant difference between the intramedullary screw TBW and the double-screw TBW (p > .05) while there was a significant difference between the traditional TBW and the other two methods (p < .05). The use of screw(s) shows higher biomechanical stability than K-wires in the TBW method. Double-screws fixation gives similar results in terms of the biomechanical load to failure compared to a large intramedullary screw fixation. Both screw methods can be used as stable constructs in clinical practice. III, biomechanical trial.

Invitro evaluation of the optimal degree of oversizing of thoracic endografts in prosthetic landing areas: a pilot study.

The optimal degree of proximal thoracic endograft oversizing when aiming for durable sealing in prosthetic grafts is unknown. The aim of the present study was to create an invitro model for testing different oversized thoracic endografts in a reproducible and standardized manner and, subsequently, determine the optimal oversizing range when planning procedures with a proximal landing in prosthetic zones in the descending thoracic aorta or aortic arch. An invitro model consisting of a fixed 24-mm polyethylene terephthalate (Dacron; DuPont) graft sutured proximally and distally to two specifically designed 40-mm rings, with four force sensing resistors attached at four equally distant positions and a USB camera attached proximally for photographic and video documentation was used for deployment of Zenith TX2 (Cook Medical Inc) dissection platform endografts with diameters between 24 and 36mm. After deployment, ballooning with a 32-mm compliant balloon was performed to simulate real-life conditions. The assessment of oversizing included visual inspection, calculation of the valley areas created between the prosthetic wall and the stent graft fabric, distance between the stent graft peaks, the radial force exerted by the proximal sealing stent, and the pull-out force necessary for endograft extraction. A total of 70 endografts were deployed with the oversizing ranging from 0% to 50%: 10× 24mm, 10× 26mm, 10× 28mm, 10× 30mm, 10× 32mm, 10× 34mm, and 10× 36mm. Two cases of infolding occurred with 50% oversizing. The valley areas increased from 8.79± 0.23mm2 with 16.7% oversizing to 14.26± 0.45mm2 with 50% oversizing (P< .001). A significant difference was found in the pull-out force required for endografts with<10% oversizing vs ≥10% oversizing (P< .001). The difference reached a plateau at ∼4 N with oversizing of >15%. The mean radial force of the proximal sealing stent was greater after remodeling with a compliant balloon (0.55± 0.02 N vs 0.60± 0.02 N after ballooning; P< .001). However, greater oversizing did not lead to an increase in the radial force exerted by the proximal sealing stent. The findings from the present study offer additional insight into the mechanics of oversized stent grafts in surgical grafts. In endografts with the Zenith stent design (TX2), oversizing of<16.7% resulted in reduced resistance to displacement forces, and oversizing of >50% was associated with major infolding in 20% of cases. Long-term invitro andinvivo testing is required to understand how these mechanical properties affect the clinical outcomes of oversizing.

Field experimental study on the pull-out characteristics of a new type of expanding shell bolt

Rock bolt foundation is becoming increasingly popular for transmission line engineering in mountainous areas due to the ability to maximize rock foundation bearing performance, reduce foundation size and burial depth, and save investment. However, failure modes such as pull-out of bolt can lead to insufficient utilization of bearing capacity of rock bolt. To overcome this problem, a new form of expanding shell bolt is proposed and the effect of several variables including grouting materials, bolt diameter, site weathering degree, and anchoring depth are investigated in this study. The results indicate that the new expanding shell bolt may significantly increase the pull-out bearing capacity compared to common rock bolts, due to the built-in effect between the bottom part of bolt and the rock on the hole wall. The effect of grouting material and anchoring length on the shell anchor's uplift bearing capacity is minimal. Considering that the ultimate tensile strength when the anchor bar breaks depends on the diameter of the steel bar, increasing the diameter of the anchor bar will effectively improve the pull-out characteristics of the bolt. The failure mode of anchor rods is also influenced by the rock layers. Rock layers with lower weathering levels have stronger embedding force, and the expansion head can effectively play a role. Due to the group anchor effect, the ultimate uplift bearing capacity of group anchor foundation in rocks is not simply the sum of the bearing capacity of each one, but must be multiplied by the group anchor coefficient. This coefficient is close to 0.9 in moderately weathered and strong-medium weathering sites. Finally, the calculation method for ultimate pullout force of expanding shell bolt is established. The feasibility of this method is verified by comparing on-site test values and calculated values.Author keywords: Rock bolt; Expanding shell bolt; Pull-out bearing capacity; Failure mode; Group anchor effect.

The Influence of Sagittal Pin Angulation on the Stiffness and Pull-Out Strength of a Monolateral Fixator Construct.

Monolateral pin-to-bar-clamp fixators are commonly used to stabilize acute extremity injuries. Certain rules regarding frame geometry have been established that affect construct stability. The influence of sagittal pin angulation on construct stiffness and strength has not been investigated. The purpose of this biomechanical study was to demonstrate the effect of a pin angulation in the monolateral fixator using a composite cylinder model. Three groups of composite cylinder models with a fracture gap were loaded with different mounting variants of monolateral pin-to-bar-clamp fixators. In the first group, the pins were set parallel to each other and perpendicular to the specimen. In the second group, both pins were set convergent each in an angle of 15° to the specimen. In the third group, the pins were set each 15° divergent. The strength of the constructions was tested using a mechanical testing machine. This was followed by a cyclic loading test to produce pin loosening. A pull-out test was then performed to evaluate the strength of each construct at the pin-bone interface. Initial stiffness analyses showed that the converging configuration was the stiffest, while the diverging configuration was the least stiff. The parallel mounting showed an intermediate stiffness. There was a significantly higher resistance to pull-out force in the diverging pin configuration compared to the converging pin configuration. There was no significant difference in the pull-out strength of the parallel pins compared to the angled pin pairs. Convergent mounting of pin pairs increases the stiffness of a monolateral fixator, whereas a divergent mounting weakens it. Regarding the strength of the pin-bone interface, the divergent pin configuration appears to provide greater resistance to pull-out force than the convergent one. The results of this pilot study should be important for the doctrine of fixator mounting as well as for fixator component design.

Investigation of Helix-Pultruded CFRP Rebar Geometry Variants for Carbon-Reinforced Concrete Structures.

Carbon concrete is a new, promising class of materials in the construction industry. This corrosion-resistant reinforcement material leads to a reduction in the concrete cover required for medial shielding. This enables lean construction and the conservation of concrete and energy-intensive cement manufacturing. Bar-type reinforcement is essential for heavily loaded structures. The newly developed helix pultrusion is the first process capable of producing carbon fiber-reinforced polymer (CFRP) reinforcement bars with a topological surface in a single pultrusion process step, with fiber orientation tailored to the specific loads. The manufacturing feasibility and load-bearing capacity were thoroughly tested and compared with other design and process variants. Approaches to increase stiffness and strength while maintaining good concrete anchorage have been presented and fabricated. Tensile testing of the helical rebar variants with a 7.2 mm lead-bearing cross-section was conducted using adapted wedge grips with a 300 mm restraint length. The new helix geometry variants achieved, on average, 40% higher strengths and almost reached the values of the base material. Concrete pull-out tests were carried out to evaluate the bond properties. The helix contour design caused the bar to twist out of the concrete test specimen. Utilizing the Rilem beam test setup, the helical contour bars could also be tested. Compared with the original helix variant, the pull-out forces could be increased from 8.5 kN to up to 22.4 kN, i.e., by a factor of 2.5. It was thus possible to derive a preferred solution that is optimally suited for use in carbon concrete.

Survival of Four Conical Implant Abutment Connections After Removal of the Abutment Screw and Simulated Cyclic Loading: An In Vitro Comparative Study.

This in vitro study evaluated the mechanical behavior of different conical connection implant systems after abutment screw withdrawal. Four conical connection systems were selected based on different conical half-angles: Ankylos (5.7°), Cowell (7.0°), Straumann (7.5°), and Astra (11.0°). In each system, 5 implants and abutments were used (n = 5). According to the recommended value, each abutment screw was torqued to settle the abutment and then withdrawn through a predesigned hole of the cemented crown. The retentiveness of the abutment was evaluated by the following mechanical testing. All specimens were subjected to cyclic loading of 20-200 N, 30°, and 4-mm off-axis to the implant axis, for 106 cycles. The pullout forces and axial displacements of the abutments were measured. The data of the Cowell system was obtained from our previous work. All groups other than Astra group, in which abutment loosened after abutment screw withdrawal, passed the cyclic loading test. Straumann group demonstrated a significantly lower pullout force (27.4 ± 21.1 N) than Ankylos (160.1 ± 41.4 N) and Cowell (183.7 ± 30.5 N) groups. All groups showed abutment rebound after screw withdrawal except Straumann group. In addition, Ankylos, Cowell, and Straumann groups demonstrated axial displacement after cyclic loading. In terms of the retentiveness of the abutment after abutment screw withdrawal examined in this study, Ankylos and Cowell groups had much higher retentiveness than Straumann group, while Astra group had none. Conical angle could be a key design parameter to make abutment screw withdrawal after conical abutment settlement feasible, but more studies must be conducted for clinical application.

Linking dynamics between anchors and granular materials

The research quantitatively explores the linking properties between the circular plate anchor and the granular assembly during the failure process under the subject of a specified pullout force given to the anchor using three-dimensional discrete particle simulations. This circular anchor is created as a hard cluster of spherical grains and is initially buried at a depth in the granular assembly. The numerical method is constructed based on the frictional interaction force law. The linking dynamic is characterized by the variation of the drag force acting on such anchor due to interaction with grains at the bottom of the frustum which is formed during the uplifting movement of the anchor. The results show that the drag force acting on the anchor first reaches a nearly constant value corresponding to the loading phenomenon at small anchor movement, reflecting the plastic deformation of granular bed as a result of particle rearrangement, and then fluctuates in a wide range, this range increases with increasing the anchor movement as a result of the unloading/reloading events. These loading/unloading/reloading events provide evidence for the linking properties between the anchor movement and granular assembly, which are highlighted by the density and intensity of force network within the frustum.

A biomechanical study of osseointegrated patient-matched additively manufactured implant for treatment of thumb amputees.

Thumb amputations leads to 50 % loss in hand functionality. To date, silicone vacuum prosthesis and autologous transplantation are the most adopted treatment solutions: nevertheless, vacuum prostheses lack in stability and cause skin issue and surgical treatment is not always accepted by patients. Osseointegrated implants were demonstrated to enhance stability, restore osseoperception and increase the time of prosthesis use. Thumb amputations present varying stump sizes: a standard size implant cannot address specificity of each patient, while a patient matched solution can meet surgeon requirements, by geometrical features of implant. The fixture presented in the current paper is the first additively manufactured patient matched osseointegrated implant for the treatment of thumb amputees. The current work aims to verify and validate a predictive finite element model (FEM) for mechanical strength of the presented fixture. FEM was demonstrated to correctly evaluate the mechanical strength of patient matched device. Minimum strength requirements were calculated in different core diameters: FEM were experimentally validated. Safety factor of 1.5 was guaranteed. Finally, considerations on performance of the prototype were carried out by means of insertion tests in Sawbones and axial pull-out force assessment. Cadaver tests to evaluate the entire procedure and production process are ongoing.

Mechanical properties of a bioabsorbable magnesium interference screw for anterior cruciate ligament reconstruction in various testing bone materials

Tears of the anterior cruciate ligament (ACL) negatively impact the stability and kinematics of the knee. Interference screws (ISs) are used for graft fixation in ACL reconstruction and provide sufficient fixation strength to withstand the patients' activities during the graft-to-bone integration process. Magnesium is a novel material used to manufacture IS given its strength and bioabsorbability. In previous studies, the selected magnesium IS design showed a better fixation performance in comparison to the conventional IS design due to its shape design and surface condition. In this study, bioabsorbable magnesium ISs were tested for their insertion (insertion torque and a number of turns to implement the IS) and fixation performance (pull-out and dynamic test). To obtain a reliable initial assessment of IS performance, ISs were implanted in 15 per cubic foot (PCF) Sawbones polyurethane foam blocks, Sawbones biomechanical tibia models with 17 PCF foam cores, and human cadaveric tibiae. Porcine tendons were used in the foam block pull-out test, and nylon ropes were used in all other test setups to prevent influences of the ligament graft material itself. In the pull-out test, the graft was subjected to tensile stress at a rate of 6 mm/min. For the dynamic test, 1000 cycles between 0 and 200 N were performed, followed by a final pull-out test. After each test, the tunnel widening pattern was observed by measuring the aspect ratio of the tunnel at the insertion site. The insertion torque lies within the normal insertion torque of the ISs as well as the average ligament tension before the insertion. In the foam block setup, the nylon rope showed a higher pull-out force than the porcine tendon. The comparison of each setup using nylon rope for both pull-out and pull-out after the dynamic test showed no significant difference between the foam block and cadaver setup. However, all tibia model setup shows unexpectedly high pull-out force due to the influence of its cortical layer. There were no statistically significant differences in tunnel widening between foam block-porcine tendon and foam block-nylon rope constructs. The pull-out resistance of magnesium ISs falls within the typical ACL tension range during daily activities. Even though the test results of the magnesium ISs are different in each bone material, the magnesium IS shows adequate fixation ability and workability during insertion without material failure.

INFLUENCE OF CEMENT CONTENT AND MOISTURE CONTENT ON THE PULLOUT-INTERFACE PROPERTIES OF GEOGRID-SOLIDIFIED WASTE MUD

In engineering, waste mud is often used as a filling material after a solidification treatment. Geogrids, being excellent geotechnical engineering materials, are often used for soil reinforcement. In this work, a pullout test that considered the influence of different waste-mud moisture contents and cement contents was conducted to investigate the interface characteristics of geogrid-solidified waste-mud-reinforced soil. Then, the relationship between the pullout force and displacement, and the variations in the cohesion, friction angle and quasifriction coefficient were analysed. The results showed that the pullout force-displacement curve represented a strain-softening pattern. With the increasing moisture content, the peak pullout force, interfacial cohesion and quasifriction coefficient decreased gradually, but the internal friction angle did not change substantially. With the increasing cement content, the peak pullout force, interfacial cohesion, internal friction angle and quasifriction coefficient increased gradually. The peak pullout force was linearly correlated with the change in the moisture content and logarithmically correlated with the change in the cement content. Compared with the moisture content, the reinforcement-soil interface was more affected by the cement content. This study provides guidelines for the mixture design of reinforced solidified waste mud.

Pullout Behavior of a Polymeric Strap in Compacted Dry Granular Material

Strap reinforcement is very commonly used as reinforcement material in mechanically stabilized earth walls (MSEW). Metal straps are mostly used as reinforcement material. However, in humid climates, where the risk of damage to metal straps due to corrosion is high, the use of geosynthetic straps is quite justified. In the Croatian coastal region, geosynthetic straps were used as reinforcement for two very high MSEWs. In both cases, the backfill material crushed stone aggregate from the neighboring site was used. According to the relevant standards, it is recommended that the backfill material should have a uniformity coefficient of Cu ≥ 4.0. To meet these requirements, it is usually necessary to sieve and crush the backfill material. To evaluate the influence of the uniformity coefficient on the friction interaction coefficient between a geosynthetic strap and a crushed stone aggregate, a series of pullout tests with different confining stresses and aggregate grain size distributions were conducted. The pullout tests were performed for three different uniformity coefficients of the crushed stone aggregate. The results confirmed the justification to use backfill material with a uniformity coefficient higher than 4.0. The pullout tests were performed with one strap, two closely spaced straps, and two separated straps. The results showed that lateral friction contributes to the pullout force in the amount of 16.1% of the total force.

Mechanical Comparison between Fenestrated Endograft and Physician-Made Fenestrations.

A fenestrated endograft (FE) is the first-line endovascular option for juxta and pararenal abdominal aortic aneurysms. A physician-modified stent-graft (PMSG) and laser in situ fenestration (LISF) have emerged to circumvent manufacturing delays, anatomic standards, and the procedure's cost raised by FE. The objective was to compare different fenestrations from a mechanical point of view. In total, five Zenith Cook fenestrations (Cook Medical, Bloomington, IN, USA) and five Anaconda fenestrations (Terumo Company, Inchinnan, Scotland, UK) were included in this study. Laser ISF and PMSG were created on a Cook TX2 polyethylene terephthalate (PET) cover material (Cook Medical, Bloomington, IN, USA). In total, five LISFs and fifty-five PMSG were created. All fenestrations included reached an 8 mm diameter. Radial extension tests were then performed to identify differences in the mechanical behavior between the fenestration designs. The branch pull-out force was measured to test the stability of assembling with a calibrated 8 mm branch. Fatigue tests were performed on the devices to assess the long-term outcomes of the endograft with an oversized 9 mm branch. The results revealed that at over 2 mm of oversizing, the highest average radial strength was 33.4 ± 6.9 N for the Zenith Cook fenestration. The radial strength was higher with the custom-made fenestrations, including both Zenith Cook and Anaconda fenestrations (9.5 ± 4.7 N and 4.49 ± 0.28 N). The comparison between LISF and double loop PMSG highlighted a higher strength value compared with LISF (3.96 N ± 1.86 vs. 2.7 N ± 0.82; p= 0.018). The diameter of the fenestrations varied between 8 and 9 mm. As the pin caliber inserted in the fenestration was 9 mm, one could consider that all fenestrations underwent an "elastic recoil" after cycling. The largest elastic recoil was observed in the non-reinforced/OC fenestrations (40%). A 10% elastic recoil was observed with LISF. In terms of mechanical behavior, the custom-made fenestration produced the highest results in terms of radial and branch pull-out strength. Both PMSG and LISF could be improved with the standardization of the fenestration creation protocol.