Proton Transfer Reaction Mass Spectrometry Instrument Research Articles

Ultrahigh Sensitivity PTR-MS Instrument with a Well-Defined Ion Chemistry.

Proton-transfer-reaction mass spectrometry (PTR-MS) is widely used for measuring organic trace gases in air. In traditional PTR-MS, both nonpolar and polar analytes are ionized with unit efficiency, as predicted from ion-molecule collision theories. This well-defined ion chemistry allows for direct quantification of analytes without prior calibration and therefore is an important characteristic of PTR-MS. In an effort to further increase the sensitivity, recently developed ultrahigh sensitivity chemical ionization mass spectrometry (CIMS) analyzers have, however, been reported to have sacrificed unit ionization efficiency for selected analytes or classes of analytes. We herein report on the development of a novel ultrasensitive PTR-MS instrument, the FUSION PTR-TOF 10k, which exhibits the same universal unit response as conventional PTR-MS analyzers. The core component of this analyzer is the newly designed FUSION ion-molecule reactor, which is a stack of concentric ring electrodes generating a static longitudinal electric field superimposed by a focusing transversal radiofrequency (RF) field. The FUSION PTR-TOF 10k instrument is equipped with an improved ion source, capable of switching between different reagent ions (H3O+, O2+, NO+, NH4+) in less than one second. The improved time-of-flight mass spectrometer analyzes m/z signals with a mass resolution in the 10000-15000 range. FUSION PTR-TOF 10k achieves sensitivities up to 80000 cps ppbV-1 and detection limits down to 0.5 pptV for a 1 s measurement time. We show time-series of naphthalene and 13C-napthalene as measured in ambient air in Innsbruck for demonstrating the sub-pptV detection capability of this novel FUSION PTR-TOF 10k.

Introducing the extended volatility range proton-transfer-reaction mass spectrometer (EVR PTR-MS)

Abstract. Proton-transfer-reaction mass spectrometry (PTR-MS) is widely used in atmospheric sciences for measuring volatile organic compounds in real time. In the most widely used type of PTR-MS instruments, air is directly introduced into a chemical ionization reactor via an inlet capillary system. The reactor has a volumetric exchange time of ∼0.1 s, enabling PTR-MS analyzers to measure at a frequency of 10 Hz. The time response does, however, deteriorate if low-volatility analytes interact with surfaces in the inlet or in the instrument. Herein, we present the extended volatility range (EVR) PTR-MS instrument which mitigates this issue. In the EVR configuration, inlet capillaries are made of passivated stainless steel, and all wetted metal parts in the chemical ionization reactor are surface-passivated with a functionalized hydrogenated amorphous silicon coating. Heating the entire setup (up to 120 ∘C) further improves the time-response performance. We carried out time-response performance tests on a set of 29 analytes having saturation mass concentrations C0 in the range between 10−3 and 105 µg m−3. The 1/e-signal decay times after instant removal of the analyte from the sampling flow were between 0.2 and 90 s for gaseous analytes. We also tested the EVR PTR-MS instrument in combination with the chemical analysis of aerosols online (CHARON) particle inlet, and 1/e-signal decay times were in the range between 5 and 35 s for particulate analytes. We show on a set of example compounds that the time-response performance of the EVR PTR-MS instrument is comparable to that of the fastest flow tube chemical ionization mass spectrometers that are currently in use. The fast time response can be used for rapid (∼1 min equilibration time) switching between gas and particle measurements. The CHARON EVR PTR-MS instrument can thus be used for real-time monitoring of both gaseous and particulate organics in the atmosphere. Finally, we show that the CHARON EVR PTR-MS instrument also rapidly detects highly oxygenated species (with up to eight oxygen atoms) in particles formed by limonene ozonolysis.

A novel method for producing NH4+ reagent ions in the hollow cathode glow discharge ion source of PTR-MS instruments

Proton-transfer-reaction mass spectrometry (PTR-MS) is seeing an increased use of NH4+ ions for the detection of amines and labile oxygenated organic compounds. NH4+ ions are usually generated from ammonia or ammonium-containing chemicals. We herein present a simple method for generating NH4+ reagent ions in the hollow cathode glow discharge ion source that nowadays most proton-transfer-reaction mass spectrometry (PTR-MS) instruments are equipped with. We show that NH4+ ions can be generated in high purity and yield by simply introducing a mixture of water vapor and nitrogen in the ion source. We also show that rapid switching (∼10 s loss of data) between the H3O+ and NH4+ operation modes is possible. Our new method can be easily implemented in most PTR-MS instruments that are currently in use, thus opening the possibility to easily operate the PTR-MS analyzer in the NH4+ chemical ionization mode.

Proton-Transfer-Reaction Mass Spectrometry: Applications in Atmospheric Sciences

Proton-transfer-reaction mass spectrometry (PTR-MS) has been widely used to study the emissions, distributions, and chemical evolution of volatile organic compounds (VOCs) in the atmosphere. The applications of PTR-MS have greatly promoted understanding of VOC sources and their roles in air-quality issues. In the past two decades, many new mass spectrometric techniques have been applied in PTR-MS instruments, and the performance of PTR-MS has improved significantly. This Review summarizes these developments and recent applications of PTR-MS in the atmospheric sciences. We discuss the latest instrument development and characterization work on PTR-MS instruments, including the use of time-of-flight mass analyzers and new types of ion guiding interfaces. Here we review what has been learned about the specificity of different product ion signals for important atmospheric VOCs. We present some of the recent highlights of VOC research using PTR-MS including new observations in urban air, biomass-burning plumes, forested regions, oil and natural gas production regions, agricultural facilities, the marine environment, laboratory studies, and indoor air. Finally, we will summarize some further instrument developments that are aimed at improving the sensitivity and specificity of PTR-MS and extending its use to other applications in atmospheric sciences, e.g., aerosol measurements and OH reactivity measurements.

Calculation of the sensitivity of proton-transfer-reaction mass spectrometry (PTR-MS) for organic trace gases using molecular properties

Proton-transfer-reaction mass spectrometry (PTR-MS) allows the detection of a large number of trace gases in air through proton-transfer reaction with H3O+ reagent ions and detection by a mass spectrometer. Measurement sensitivities can be experimentally determined using calibration gases or calculated using the rate constant for the proton-transfer reaction, but rate constants have only been measured for a subset of compounds. Numerous theoretical approaches that describe the ion-molecule collision processes have shown how to accurately calculate capture collision rate constants between an ion and neutral molecules using the polarizability and permanent dipole moment of the molecule. Here we show that polarizability, dipole moment, and resulting capture rate constants for proton-transfer reactions of H3O+ with various different volatile organic compounds (VOCs) can be obtained using the molecular mass, elemental composition, and functionality of VOCs. The polarizabilities of a class of VOCs possessing a specific number of electronegative atoms were linearly correlated with their molecular mass. The dipole moments in a series of VOCs, in which VOCs contain a specific functional group and arbitrary residual hydrocarbon parts, can be approximated as a constant value. The capture rate constants calculated using polarizability and dipole moment, as estimated from molecular mass, elemental composition, and functional group, agreed within 10% with measured values for most VOCs. Those capture rate constants were applied to the calculation of the sensitivities of VOCs detected by our PTR-MS, taking into account the ion transmission efficiency and the degree of fragmentation of protonated VOCs observed in that instrument as well as chemical properties of the VOCs. The resulting calculated sensitivities agreed within 20–50% of those measured by PTR-MS, but several notable exceptions exist. This result shows that the neutral concentration of a VOC detected as a protonated molecule in PTR-MS can be approximated using only molecular mass, elemental composition, and functionality of the VOC. The present study is useful for all PTR-MS instruments regardless of the type of mass analyzer; however, the identification of elemental composition by high mass resolution instrumentation is important.

Measuring OVOCs and VOCs by PTR-MS in an urban roadside microenvironment of Hong Kong: relative humidity and temperature dependence, and field intercomparisons

Abstract. Volatile organic compound (VOC) control is an important issue of air quality management in Hong Kong because ozone formation is generally VOC limited. Several oxygenated volatile organic compound (OVOC) and VOC measurement techniques – namely, (1) offline 2,4-dinitrophenylhydrazine (DNPH) cartridge sampling followed by high-performance liquid chromatography (HPLC) analysis; (2) online gas chromatography (GC) with flame ionization detection (FID); and (3) offline canister sampling followed by GC with mass spectrometer detection (MSD), FID, and electron capture detection (ECD) – were applied during this study. For the first time, the proton transfer reaction–mass spectrometry (PTR-MS) technique was also introduced to measured OVOCs and VOCs in an urban roadside area of Hong Kong. The integrated effect of ambient relative humidity (RH) and temperature (T) on formaldehyde measurements by PTR-MS was explored in this study. A Poly 2-D regression was found to be the best nonlinear surface simulation (r = 0.97) of the experimental reaction rate coefficient ratio, ambient RH, and T for formaldehyde measurement. This correction method was found to be better than correcting formaldehyde concentrations directly via the absolute humidity of inlet sample, based on a 2-year field sampling campaign at Mong Kok (MK) in Hong Kong. For OVOC species, formaldehyde, acetaldehyde, acetone, and MEK showed good agreements between PTR-MS and DNPH-HPLC with slopes of 1.00, 1.10, 0.76, and 0.88, respectively, and correlation coefficients of 0.79, 0.75, 0.60, and 0.93, respectively. Overall, fair agreements were found between PTR-MS and online GC-FID for benzene (slope = 1.23, r = 0.95), toluene (slope = 1.01, r = 0.96) and C2-benzenes (slope = 1.02, r = 0.96) after correcting benzene and C2-benzenes levels which could be affected by fragments formed from ethylbenzene. For the intercomparisons between PTR-MS and offline canister measurements by GC-MSD/FID/ECD, benzene showed good agreement, with a slope of 1.05 (r = 0.62), though PTR-MS had lower values for toluene and C2-benzenes with slopes of 0.78 (r = 0.96) and 0.67 (r = 0.92), respectively. All in all, the PTR-MS instrument is suitable for OVOC and VOC measurements in urban roadside areas.

Sensitive detection of <i>n</i>-alkanes using a mixed ionization mode proton-transfer-reaction mass spectrometer

Abstract. Proton-transfer-reaction mass spectrometry (PTR-MS) is a technique that is widely used to detect volatile organic compounds (VOCs) with proton affinities higher than water. However, n-alkanes generally have a lower proton affinity than water and therefore proton transfer (PT) by reaction with H3O+ is not an effective mechanism for their detection. In this study, we developed a method using a conventional PTR-MS to detect n-alkanes by optimizing ion source and drift tube conditions to vary the relative amounts of different primary ions (H3O+, O2+, NO+) in the reaction chamber (drift tube). There are very few studies on O2+ detection of alkanes and the mixed mode has never been proposed before. We determined the optimum conditions and the resulting reaction mechanisms, allowing detection of n-alkanes from n-pentane to n-tridecane. These compounds are mostly emitted by evaporative/combustion process from fossil fuel use. The charge transfer (CT) mechanism observed with O2+ was the main reaction channel for n-heptane and longer n-alkanes, while for n-pentane and n-hexane the main reaction channel was hydride abstraction (HA). Maximum sensitivities were obtained at low E ∕ N ratios (83 Td), low water flow (2 sccm) and high O2+ ∕ NO+ ratios (Uso = 180 V). Isotopic 13C contribution was taken into account by subtracting fractions of the preceding 12C ion signal based on the number of carbon atoms and the natural abundance of 13C (i.e., 5.6 % for n-pentane and 14.5 % for n-tridecane). After accounting for isotopic distributions, we found that PT cannot be observed for n-alkanes smaller than n-decane. Instead, protonated water clusters of n-alkanes (M ⋅ H3O+) species were observed with higher abundance using lower O2+ and higher water cluster fractions. M ⋅ H3O+ species are probably the source for the M + H+ species observed from n-decane to n-tridecane. Normalized sensitivities to O2+ or to the sum of O2++ NO+ were determined to be a good metric with which to compare sensitivities for n-alkane detection between experiments. Double hydride abstraction was observed from the reaction with O2+. Sensitivity to CT increased with carbon chain length from n-pentane to n-dodecane, sensitivity to HA increased from n-heptane to n-dodecane and sensitivity to PT increased from n-decane to n-tridecane. Sensitivity to CT exponentially decreased with molecular ionization energy, which is inversely related to the carbon chain length. We introduce a calibrated fragmentation algorithm as a method to determine the concentrations of n-alkanes and demonstrate its effectiveness using a custom n-alkane mixture and a much more complex oil example representing perhaps the most difficult mixture available for application of the method. We define optimum conditions for using the mixed ionization mode to measure n-alkanes in conventional PTR-MS instruments regardless of whether they are equipped with switchable reagent ion (SRI) capabilities.

Natural Gas Trace Compounds Analysis with Innovative Systems: PTR-ToF-MS and FASTGC

The technique of proton transfer reaction mass spectrometry (PTR-MS) couples a proton transfer reagent, usually H3O+, with a drift tube and mass spectrometer to determine concentrations of volatile organic compounds. Proton transfer reaction-mass spectrometry (PTR-MS) has successfully been applied to a wide variety of matrices to identify and to investigate on the behavior of trace compounds; among the possible field of applications we can find: food, air, energy, etc. Natural gas is considered as a fuel for high energy efficiencies applications such as SOFC generators. The ability to distinguish several isobaric aldehydes, ketones, isoprenoids and other compounds is impossible using PTR-MS instrument. In the present research work, PTR-ToF-MS was coupled to a prototype FastGC system allowing for a rapid (90 s) chromatographic separation of the sample headspace prior to PTR-MS analysis. The system was tested on natural gas trace compounds to individuate the major elements and to identify possible issues for the SOFC generators. In comparison to the results obtained by direct injection, FastGC provided additional information, thanks to a less drastic dilution of the sample and due to the chromatographic separation of isomers. This was achieved without increasing duration and complexity of the analysis.

Online exhaled gas measurements for radiotherapy patients by proton transfer reaction mass spectrometry

The present study assessed whether exhaled breath analysis using proton transfer reaction mass spectrometry (PTR-MS) could screen for radiation exposure. As the intensity of proton transfer reaction reagent ion H316O+ can be calculated with the intensity of H318O+, the intensity of H318O+ was monitored to observe the stability of the PTR-MS instrument during the experiment. The PTR-MS was applied for detecting the volatile organic compounds (VOCs) in the exhaled breath from 42 radiotherapy patients and other 61 patients who had not received radiotherapy. All patients were enrolled in the local cancer hospital. In the experiment, the subjects breathe slowly to the PTR-MS through a direct inlet system without any sampling bag or tube. The breath mass spectrometric data was statistically analyzed using Mann-Whitney U test and stepwise discriminant analysis to find the characteristic ions of radiation exposure. Receiver operating characteristics (ROC) analysis was applied for a combination of the characteristic ions. The PTR-MS instrument was stable as the intensity of reaction ion H316O+ was maintained in 1.1%. Through statistically analysis, we found 6 kinds of characteristic ions of radiation exposure, specifically mass-to-charge ratio (m/z) 93, m/z 41, m/z 102, m/z 79, m/z 131, and m/z 143. The sensitivity (true positive rate) and specificity (true negative rate) were 78.6% and 82.0% respectively. The integrated area under the ROC curve (AUC) was 0.869. The results in our study demonstrated the potential of the online breath tester PTR-MS as a non-invasive screening for radiation exposure.

An online method for the analysis of volatile organic compounds in electronic cigarette aerosol based on proton transfer reaction mass spectrometry

RationaleDue to the recent rapid increase in electronic cigarette (e‐cigarette) use worldwide, there is a strong scientific but also practical interest in analyzing e‐cigarette aerosols. Most studies to date have used standardized but time‐consuming offline technologies. Here a proof‐of‐concept for a fast online quantification setup based on proton transfer reaction mass spectrometry (PTR‐MS) is presented.MethodsThe combination of a novel sampling interface with a time‐of‐flight PTR‐MS instrument specially designed for three scenarios is introduced: (i) mainstream aerosol analysis (aerosol that the user inhales prior to exhalation), and analysis of exhaled breath following (ii) mouth‐hold (no inhalation) and (iii) inhalation of e‐cigarette aerosols. A double‐stage dilution setup allows the various concentration ranges in these scenarios to be accessed.ResultsFirst, the instrument is calibrated for the three principal constituents of the e‐cigarettes' liquids, namely propylene glycol, vegetable glycerol and nicotine. With the double‐stage dilution the instrument's dynamic range was easily adapted to cover the concentration ranges obtained in the three scenarios: 20–1100 ppmv for the mainstream aerosol characterisation; 4–300 ppmv for the mouth‐hold; and 2 ppbv to 20 ppmv for the inhalation experiment.ConclusionsIt is demonstrated that the novel setup enables fast, high time resolution e‐cigarette studies with online quantification. This enables the analysis and understanding of any puff‐by‐puff variations in e‐cigarette aerosols. Large‐scale studies involving a high number of volunteers will benefit from considerably higher sample throughput and shorter data processing times. © 2016 The Authors. Rapid Communications in Mass Spectrometry Published by John Wiley & Sons Ltd.

Influence of co-vapors on biogas filtration for fuel cells monitored with PTR-MS (Proton Transfer Reaction-Mass Spectrometry)

Solid Oxide Fuel Cells (SOFCs) fed by biogenic fuels are a key renewable energy technology. Fuel contaminants, and sulfur compounds in particular, can strongly decrease SOFC performance. For this reason, their accurate, high sensitivity, and rapid monitoring and the development of successful removal strategies are major challenges in SOFC research.In this work the removal efficiency of commercial activated carbon filters for biogas filtering upstream of an SOFC was investigated using a Proton Transfer Reaction-Mass Spectrometry instrument (PTR-MS). In particular, we tested sulfur compounds by focusing on the effect of co-vapor adsorption (aromatic, carbonyl and chloro-compounds which are biogas pollutants) on filter performance. The results demonstrate the applicability of PTR-MS for investigating covapor effects which are of practical relevance for SOFC development.

Distinguishing two isomeric mephedrone substitutes with selective reagent ionisation mass spectrometry (SRI‐MS)

The isomers 4-methylethcathinone and N-ethylbuphedrone are substitutes for the recently banned drug mephedrone. We find that with conventional proton transfer reaction mass spectrometry (PTR-MS), it is not possible to distinguish between these two isomers, because essentially for both substances, only the protonated molecules are observed at a mass-to-charge ratio of 192 (C12 H18NO(+)). However, when utilising an advanced PTR-MS instrument that allows us to switch the reagent ions (selective reagent ionisation) from H3O(+) (which is commonly used in PTR-MS) to NO(+), O2(+) and Kr(+), characteristic product (fragment) ions are detected: C4H10N(+) (72 Da) for 4-methylethcathinone and C5 H12N(+) (86 Da) for N-ethylbuphedrone; thus, selective reagent ionisation MS proves to be a powerful tool for fast detection and identification of these compounds.

Volcanic forcing as a major source of European regional decadal climate variability during the last millennium

The technique of proton transfer reaction mass spectrometry (PTR-MS) couples a proton transfer reagent, usually H3O+, with a drift tube and mass spectrometer to determine concentrations of volatile organic compounds. Proton transfer reaction-mass spectrometry (PTR-MS) has successfully been applied to a wide variety of matrices to identify and to investigate on the behavior of trace compounds; among the possible field of applications we can find: food, air, energy, etc. Natural gas is considered as a fuel for high energy efficiencies applications such as SOFC generators. The ability to distinguish several isobaric aldehydes, ketones, isoprenoids and other compounds is impossible using PTR-MS instrument. In the present research work, PTR-ToF-MS was coupled to a prototype FastGC system allowing for a rapid (90 s) chromatographic separation of the sample headspace prior to PTR-MS analysis. The system was tested on natural gas trace compounds to individuate the major elements and to identify possible issues for the SOFC generators. In comparison to the results obtained by direct injection, FastGC provided additional information, thanks to a less drastic dilution of the sample and due to the chromatographic separation of isomers. This was achieved without increasing duration and complexity of the analysis.

Rapid and facile detection of four date rape drugs in different beverages utilizing proton transfer reaction mass spectrometry (PTR‐MS)

In this work, we illustrate the application of proton transfer reaction mass spectrometry (PTR-MS) in the field of food and drink safety. We present proof-of-principle measurements of four different drinks (water, tea, red wine and white wine) each spiked separately with four different date rape drugs (chloral hydrate, tricholorethanol, γ-butyrolactone and butanediol). At first, the ideal PTR-MS operating conditions (reduced electric field strength and monitoring the most abundant [fragment] ion) for detection of the drugs were determined utilizing a time-of-flight-based PTR-MS instrument. We then dissolved small quantities of the drugs (below the activation threshold for effects on humans) into the various types of drinks and detected them using a quadrupole-based PTR-MS instrument via two different sampling methods: (1) dynamic headspace sampling and (2) direct liquid injection. Both methods have their advantages and drawbacks. Only with dynamic headspace sampling can rape drug contaminations be detected within a timeframe of seconds, and therefore, this method is the most promising use of PTR-MS as a fast, sensitive and selective monitor for the detection of food and drink contamination.

From conventional proton-transfer-reaction mass spectrometry (PTR-MS) to universal trace gas analysis

We present here a slightly modified PTR-MS instrument that is not only capable to ionize trace compounds in air via proton-transfer-reactions (PTR) but is also able to ionize via charge-transfer-reactions (CTR) with help of reagent ions (Kr+ in particular) possessing higher ionization energies than common air constituents. This means that with minor adaptations a common PTR-MS instrument can be used for the analysis of nearly all available substance classes by using both PTR and/or CTR ionization. Especially in environmental research, the field of application where PTR-MS is used most widely, now not only trace volatile organic compounds (benzene, toluene, etc.) but additionally also very important (inorganic) substances, such as CO, CO2, CH4, NOx, and SO2, can be detected and quantified with the same instrument. As all ionizing agents are produced in a hollow cathode discharge ion source with good purity no additional mass filter is needed for reagent ion selection (as in other analytical methods employed) and remaining reagent ion impurities can be clearly distinguished from isobaric sample compounds due to the high mass resolution of the time-of-flight mass spectrometer used in the present PTR-MS instrument (PTR-TOF 8000). We present data obtained with various gas standards ranging from a “classical” PTR-MS aromatics mixture to samples containing molecules possessing ionization energies all the way up to 14eV (CO).

Detection of isocyanates and polychlorinated biphenyls using proton transfer reaction mass spectrometry

Isocyanates are highly reactive species widely used in industry. They can cause irritation of the eyes, trigger asthma, etc. Polychlorinated biphenyls (PCBs) were widely used in electrical equipments like capacitors and transformers in the last century and are still present in the environment today. PCBs are known to cause cancer and to affect the immune, reproductive, nervous and endocrine systems. Therefore, there is a need for a simple, rapid and reliable analytical method for the detection of traces of isocyanates and of PCBs. The data presented in this paper were obtained using a proton transfer reaction (PTR) time-of-flight mass spectrometer and a high sensitivity PTR quadrupole mass spectrometer. We also utilized a recently developed direct aqueous injection (DAI) inlet system for proton transfer reaction mass spectrometry (PTR-MS) instruments that allows the analysis of trace compounds in liquids. We detected four isocyanates in the headspace above small sample quantities and investigated their fragmentation pathways to obtain a fundamental understanding of the processes involved in proton transfer reactions and also to determine the best operating conditions of the PTR-MS instruments. In addition, nine PCBs were unambiguously identified via their exact mass and isotopic distribution and detected in different concentration levels via direct injection of the liquid. Utilizing recent developments and improvements in PTR-MS, we can rapidly detect two important environmental pollutant compound classes (isocyanates and PCBs) at high accuracy and without any sample preparation. In this paper, we provide proof of the detection of traces of isocyanates and PCBs in air and also of PCBs in liquids. These results could be used for the development of a real-time monitoring device for industrial waste, polluted air or water quality surveillance.

Airborne formaldehyde measurements using PTR-MS: calibration, humidity dependence, inter-comparison and initial results

Abstract. We present quantitative, fast time response measurements of formaldehyde (HCHO) onboard an aircraft using a Proton-Transfer-Reaction Mass-Spectrometry (PTR-MS) instrument. The HCHO measurement by PTR-MS is strongly humidity dependent and therefore airborne measurements are difficult and have not been reported. The PTR-MS instrument was run in the standard PTR-MS operating mode (de Gouw and Warneke, 2007), where about 15 volatile organic compounds (VOCs) are measured together with HCHO onboard the NOAA WP-3 aircraft during the CalNex 2010 campaign in California. We compare the humidity dependence determined in the laboratory with in-flight calibrations of HCHO and calculate the HCHO mixing ratio during all flights using the results from both. The detection limit (S/N = 1) for HCHO was between 100 pptv in the dry free troposphere and 300 pptv in the humid marine boundary layer for a one second acquisition time every 17 s. The PTR-MS measurements are compared with HCHO measurements using a DOAS instrument and a Hantzsch monitor at a ground site in Pasadena. The PTR-MS agreed with the DOAS within the stated uncertainties and was just outside the uncertainties with the Hantzsch. We also compare HCHO enhancement ratios in the Los Angeles basin and in the free troposphere with literature values and find good agreement. The usefulness of the PTR-MS HCHO measurements in atmospheric observations is demonstrated by following an isolated anthropogenic plume. The photochemical production of HCHO can be observed simultaneously with production of acetaldehyde and the photochemical degradation of aromatic compounds using the PTR-MS. The results show that PTR-MS seems a useful instrument to measure HCHO, but more inter-comparisons are needed.

Characterization of an olfactometer by proton-transfer-reaction mass spectrometry

The performance of a commercial olfactometer instrument, which produces odorant pulses of defined duration and concentration, was characterized using proton-transfer-reaction mass spectrometry (PTR-MS). Direct coupling of the PTR-MS instrument with the olfactometer enabled on-line evaluation of the rapidly delivered aroma pulses. Tests were made with a selection of four odorous compounds: hydrogen sulfide, 2,3-butanedione, ethyl butanoate and ethyl hexanoate. Odour concentrations and stimulus durations for these compounds were monitored directly at the olfactometer delivery port via the respective PTR-MS signals. The performance of the olfactometer was found to be dependent on pulse duration. A decrease over time in maximum intensity for identical pulses over an extended duration showed headspace concentration depletions for compounds sourced from a water solution, indicative of gas/liquid partitioning. Such changes were not present using odours sourced from a cylinder or, presumably, when using liquid odours at neat concentrations. In conclusion, while an olfactometer provides stimuli with good reproducibility, the concept is subject to certain limitations that must be appreciated by the experimenter for accurate application of this technique.

Real-time profiling of organic trace gases in the planetary boundary layer by PTR-MS using a tethered balloon

Abstract. A method for real-time profiling of volatile organic compounds (VOCs) was developed combining the advantages of a tethered balloon as a research platform and of proton transfer reaction mass spectrometry (PTR-MS) as an analytical technique for fast and highly sensitive VOC measurements. A 200 m Teflon tube was used to draw sampling air from a tethered aerodynamic balloon to the PTR-MS instrument. Positive and negative artefacts (i.e. formation and loss of VOCs in the tube) were characterised in the laboratory and in the field by a set of 11 atmospherically relevant VOCs including both pure and oxygenated hydrocarbons. The only two compounds that increased or decreased when sampled through the tube were acetone (+7%) and xylene (-6%). The method was successfully deployed during a winter field campaign to determine the small scale spatial and temporal patterns of air pollutants under winter inversion conditions.

A high resolution and high sensitivity proton-transfer-reaction time-of-flight mass spectrometer (PTR-TOF-MS)

Proton-transfer-reaction mass spectrometry (PTR-MS) developed about 10 years ago is used today in a wide range of scientific and technical fields allowing real-time on-line measurements of volatile organic compounds in air with a high sensitivity and a fast response time. Most instruments employed so far use quadrupole filters to analyze product ions generated in the reaction drift tube. Due to the low mass resolution of the quadrupoles used this has the disadvantage that identification of trace gases under study is not unambiguous. Here we report the development of a new version of PTR-MS instruments using a time-of-flight mass spectrometer, which is capable of measuring VOCs at ultra-low concentrations (as low as a few pptv) under high mass resolution (as high as 6000 m/Δm in the V-mode) with a mass range of beyond 100 000 amu. This instrument was constructed by interfacing the well characterized and recently improved Ionicon hollow cathode ion source and drift tube section with a Tofwerk orthogonal acceleration reflectron time-of-flight mass spectrometer. We will first discuss the set-up of this new PTR-TOF-MS mass spectrometer instrument, its performance (with a sensitivity of several tens of cps/ppbv) and finally give some examples concerning urban air measurements where sensitivity, detection limit and mass resolution is essential to obtain relevant data.