Properties Of Samples Research Articles

Influence of Solution Treatment Process on the Properties of Duplex Stainless Steels: A Comparative Study on Microstructure and Corrosion Properties of UNS S32205 and UNS S32760

The study investigated the effect of the solution treatment process on the corrosion behavior and microstructure of the duplex stainless steel. It was also aimed to reveal this effect comparatively depending on the chemical composition and alloying element content. For this purpose, UNS S32205 and UNS S32760 alloys were treated at 1000 °C, 1020 °C and 1040 °C for an hour. A solution treatment temperature was determined according to Thermo-Calc analysis. The examined samples were characterized by an optical microscope, scanning electron microscope, and XRD analysis. Also, electrochemical impedance spectroscopy and potentiodynamic polarization analyses revealed the corrosion properties of solution-treated samples. Microstructural studies showed that enhanced solution treatment temperature increased ferrite content for both alloys. A lower solution treatment temperature caused the formation of sigma in the microstructure of S32760 alloy. On the other hand, the charge transfer resistance of the passive layer was reduced after solution treatment at 1000 °C and 1020 °C, indicating decreasing corrosion resistance. A higher austenite ratio in S32205 led to pitting, while corrosion resistance improved with higher treatment temperatures. The presence of the sigma phase in S32760 significantly impacted corrosion properties by increasing ion transfer on the surface, leading to reduced corrosion resistance. It was determined that solution treatment at 1040 °C was appropriate for both alloys to achieve the desired microstructure and corrosion properties.

Precipitation behaviors and the related strengthening mechanism in 2219 Al alloy fabricated by wire arc additive manufacturing

Normally, a large number of dislocations could be introduced into the metallic component in the additive manufacturing process. The effects of these thermal stress-induced dislocations on the precipitation of 2219 Al alloy have thus far not been comprehensively studied. In the present study, the precipitation behaviors of 2219 Al alloys fabricated by wire arc additive manufacturing are investigated in detail by multi-scale experimental methods, including transmission electron microscopy, scanning electron microscopy, and X-ray diffraction analyses. Our study suggests that the stress-induced dislocations could act as the heterogenous nucleation sites, facilitating the precipitation of θ′ and θ′′ phases in the deposition process. During the subsequent artificial aging, θ′ and θ′′ phases are present in the 160°C peak-aged sample. Raising the aging temperature from 160°C to 180°C could facilitate the transformation of θ′′ to θ′ phases. Moreover, for the 200°C peak-aged sample, the number density of θ′ phases appears to decrease with accompanied coarsening. An evident improvement occurs in the comprehensive mechanical properties of the as-deposited sample by appropriate heat treatment (540℃/3 h-180℃/14 h). The ultimate tensile strength significantly increases from 238 MPa to 408 MPa, exhibiting an enhancement of approximately 70 %, while the elongation increases from 14 % to 15 %. Additionally, a quantitative correlation is established between the precipitate characteristics and mechanical properties.

Estimation of the conditional tail moment for Weibull‐type distributions

AbstractWe consider the estimation of the conditional tail moment at extreme levels for the class of Weibull‐type distributions. A two‐step procedure is introduced where in the first stage one estimates the conditional tail moment at an intermediate level, followed by an extrapolation in the second stage. The asymptotic properties of the estimators introduced in the two stages are derived under suitable assumptions. The finite sample properties of the proposed estimator are examined with a simulation experiment. We conclude with two applications on real life data: wind speed measurements collected at an offshore wind farm and air pollution data.

Investigation of influence of technological parameters on the properties of SiC samples fabricated by selective laser sintering. Part 1

Investigation of influence of technological parameters on the properties of SiC samples fabricated by selective laser sintering. Part 1

Three-Dimensional Bioprinted Skin Microrelief and Its Role in Skin Aging.

Skin aging is a complex physiological process, in which cells and the extracellular matrix (ECM) interreact, which leads to a change in the mechanical properties of skin, which in turn affects the cell secretion and ECM deposition. The natural skin microrelief that exists from birth has rarely been taken into account when evaluating skin aging, apart from the common knowledge that microreliefs might serve as the starting point or initialize micro-wrinkles. In fact, microrelief itself also changes with aging. Does the microrelief have other, better uses? In this paper, owing to the fast-developing 3D printing technology, skin wrinkles with microrelief of different age groups were successfully manufactured using the Digital light processing (DLP) technology. The mechanical properties of skin samples with and without microrelief were tested. It was found that microrelief has a big impact on the elastic modulus of skin samples. In order to explore the role of microrelief in skin aging, the wrinkle formation was numerically analyzed. The microrelief models of different age groups were created using the modified Voronoi algorithm for the first time, which offers fast and flexible mesh formation. We found that skin microrelief plays an important role in regulating the modulus of the epidermis, which is the dominant factor in wrinkle formation. The wrinkle length and depth were also analyzed numerically for the first time, owing to the additional dimension offered by microrelief. The results showed that wrinkles are mainly caused by the modulus change of the epidermis in the aging process, and compared with the dermis, the hypodermis is irrelevant to wrinkling. Hereby, we developed a hypothesis that microrelief makes the skin adaptive to the mechanical property changes from aging by adjusting its shape and size. The native-like skin samples with microrelief might shed a light on the mechanism of wrinkling and also help with understanding the complex physiological processes associated with human skin.

The influence of secondary raw materials of grain processing on the rheological properties of the dough

The development of technologies and new recipes for bakery products with increased nutritional value is a promising direction for the food industry. The expansion of the assortment is due to the introduction of additional raw materials, one of the options of which is rice and buckwheat flour. Rice and buckwheat flour contain a wide range of biologically active substances that, when added to food, have a beneficial effect on the human body. The main objects of research were flour composite mixtures obtained by mixing wheat flour of the first grade, rice, and buckwheat flour in a percentage ratio of 95:2:3, 90:3:7, 85:4:11, 80:5:15, 75:6:19, accordingly. The aim of the study was to study the influence of secondary raw materials of grain processing on the rheological properties of the dough to justify their introduction into the production of bakery products for functional purposes. The study of semifinished product samples was carried out using the following devices: Chopin alveograph (NG with the prefix alveolink) and Mixolab 2 (CHOPIN Technologies, France). The study of the rheological properties of the test samples under study showed that the introduction of secondary raw materials of grain crops – rice and buckwheat flour into the formulation of wheat bread in a dosage of 4% - 11%, respectively, improved the rheological and physico-chemical properties of the dough, which contributed to the development of the formulation and technology of a new type of enriched bread.

Application and safety of pectin substances from vegetable raw materials in bread production

Currently, pectin substances and their compounds are often used in cooking as an anionic surfactant. In the technology of food preparation, such properties of pectin substances as swelling, thickening, gel-forming, crystalforming, water-absorbing ability, and emulsifying ability are of great importance. Like any gel-forming fiber, pectin helps remove heavy metals from the body such as lead, mercury, cadmium, etc. MCP may be better suited for these purposes, as it has been used in four clinical studies of heavy metal detoxification. Considering the accumulation of radioactive elements, heavy metal salts and pesticides in the environment and the human body, Jerusalem artichoke, which is rich in pectin substances, carotene and dietary fiber, is of particular interest. It is also economically beneficial as it is a domestic raw material. The goal of scientific research is to obtain a new type of functional bread with the addition of vegetable pectin. In this article, it was determined that the addition of pectin to dough has an effect on biochemical, colloidal, as well as microbiological processes. It also affects the physicochemical and rheological properties and reduces the content of contaminants. The work investigated that when pectin substances are added to the dough, its initial acidity increases. Acidity varied 2.2-2.4. It was also noted that in the test sample the fermentation process was more active; the activity of the fermentation process was associated with the addition of sugar along with pectin. As a result of this work, in order to improve the quality of bread and extend shelf life, pectin from raw materials of plant origin was added, the properties of bread samples with Jerusalem artichoke pectin with high performance were studied, and their organoleptic, physicochemical and safety indicators were studied. It was revealed that pectin reduces the content of some toxic elements by up to 100%. Practical significance: the conducted studies showed that the obtained samples of functional bread can be recommended for introduction into production to expand the range of bakery products.

The Study of Composite Materials Properties Based on Polymers and Nano-Additives from Industrial Wastes from Kazakhstan.

This research is aimed at studying the properties of polymer anticorrosion coatings based on ED-20 resin widely used in practice and industrial wastes. In this work, three basic types of nanoscale nanofillers were chosen: dispersed particles-microsilica, microspheres obtained at Kazakh enterprises, and carbon nanotubes. Physicochemical research methods were used in the research: a laser analyzer for studying the dispersibility of industrial waste and spectrometric research methods. The properties of materials were investigated by standardized methods. The obtained results show that the introduction of microsilica and microspheres obtained at Kazakhstani enterprises, used as additives, improves both the physical and mechanical properties of epoxy composites compared to the standard (control) material. The results of experiments have shown that the optimal content of additives of microsilica and microspheres provides an improvement in the physical and mechanical properties of epoxy composites in comparison with the standard (control) material. Studies have shown that the introduction of microspheres into ED-20 polymer increases impact toughness. The introduction of microsilica into the matrix contributes to the increase of elastic modulus. Experimental studies of optical properties of samples of carbon composite polymer films based on polystyrene (PS) with additives of carbon nanotubes C60 and C70 and multilayer carbon nanotubes were also carried out. The experimental results obtained for the optical properties of polymer composites based on basic polymers from solid waste and carbon nanotubes showed that the optical properties of polymer composites undergo noticeable changes.

Rare earth elements recovery and mechanisms from coal fly ash by column leaching using citric acid

Rare earth elements (REEs) play an irreplaceable role in supporting the advancement of the global economy and technology, but their limited supply drives researchers to devise effective strategies for the recovery of REEs from alternative sources, including coal fly ash (CFA). In this work, a new column leaching method using citric acid as the lixiviant was proposed to enhance the recovery of REEs from CFA at room temperature. The mechanism of column leaching was investigated based on sample properties, leaching results, and the adsorption characteristics and complexation of citric acid. REEs in the CFA were found to be hosted into the amorphous aluminosilicate matrix in the form of oxides and fluorides using SEM-EDS. Compared to the maximum recovery of total REEs (TREEs, < 30 %) in the conventional agitation leaching tests, the recovery of TREEs in the column leaching tests increased significantly to 64.8 %, while the leaching rate of impurities (Al, Ti, and Fe) was less than 13.7 %. Results of the Zeta potential measurements showed that the citric acid and rare earth cations were adsorbed on the surface of CFA particles. These adsorption phenomena may make REEs bind to the CFA surface, thereby resulting in low leaching recoveries of REEs. Rare earth-citrate complexes in the lixivium were isolated by antisolvent precipitation, demonstrating that rare earth cations can be complexed by citrate. During the column leaching process, the leached rare earth ions were complexed with citrate and then carried away with the flowing liquid phase, which improved the recovery of REEs.

Optimizing the composition of barium-borate glasses for enhancing thermal neutron shielding efficiency: Monte Carlo simulation

A transparent window with thermal neutron shielding properties was an important part of the stations of the nuclear reactors and the particle accelerators. The borate glass with a high neutron cross section was a candidate as a glass network for the neutron shielding window. In order to slow down thermal neutrons, they were trapped by boron and subsequently emitted secondary radiation, such as alpha particles and gamma-ray radiation. This work was to optimize the content between a ratio of borate with a high cross-section neutron interaction and barium for shielding alpha and gamma ray. The barium-borate glasses were successfully synthesized using the melting technique in the atmosphere. Measurements of mechanical and optical glass properties were presented. The measured results showed that an increase in barium oxide content in the glass ratio enhanced the glass density and the transmittance at a visible wavelength. In the calculation of radiation shielding properties, FLUKA code based on Monte Carlo Simulation was demonstrated. The calculated results revealed that an increase in the barium oxide content in the glass composition reduced the thermal neutron shielding properties of the glass samples. In contrast, the glass with barium contents enhanced the photon-shielding efficiency, as indicated by the mass attenuation coefficient and half-value layer. Not only the ratio of the barium and borate contents affected the shielding properties, but the increased glass thickness also enhanced the shielding properties. Thus, the utilization of cooperative borate glasses and barium with appropriate thickness could potentially serve as a viable option for simultaneously protecting against thermal neutrons and photons. The barium-borate glasses with our composition might be used as a window in a thermal neutron station as well as for photon radiation.

Effects of Low-Temperature Heat Treatment on Mechanical and Thermophysical Properties of Cu-10Sn Alloys Fabricated by Laser Powder Bed Fusion.

This study investigated the impact of low-temperature heat treatments on the mechanical and thermophysical properties of Cu-10Sn alloys fabricated by a laser powder bed fusion (LPBF) additive manufacturing (AM) process. The microstructure, phase structure, and mechanical and thermal properties of the LPBF Cu-10Sn samples were comparatively investigated under both the as-fabricated (AF) condition and after low-temperature heat treatments at 140, 180, 220, 260, and 300 °C. The results showed that the low-temperature heat treatments did not significantly affect the phase and grain structures of the Cu-10Sn alloys. Both pre- and post-treatment samples displayed consistent grain sizes, with no obvious X-ray diffraction angle shift for the α phase, indicating that atom diffusion of the Sn element is beyond the detection resolution of X-ray diffractometers (XRD). However, the 180 °C heat-treated sample exhibited the highest hardness, while the AF samples had the lowest hardness, which was most likely due to the generation of precipitates according to thermodynamics modeling. Heat-treated samples also displayed higher thermal diffusivity values than their AF counterpart. The AF sample had the longest lifetime of ~0.19 nanoseconds (ns) in the positron annihilation lifetime spectroscopy (PALS) test, indicating the presence of the most atomic-level defects.

Diffusion coefficients in scaffolds made with temperature controlled cryoprinting and an ink made of sodium alginate and agar

Temperature Controlled Cryoprinting (TCC), is a tissue engineering technique wherein each deposited voxel is frozen with precise control over cooling rates and the direction of freezing. This control allows for the generation of ice crystals with controlled shape and orientation. Recently we found that the macroscale fidelity of the TCC print is substantially improved by using a 3D printing ink composed of a mixture of two compounds: one that solidifies through chemical crosslinking (sodium alginate) and another that solidifies through physical (thermal) effects (agar). In this study we examine the hypothesis that the combination of sodium alginate and agar, affects also the fidelity of the microstructure and thereby the diffusivity of the scaffold. The ability of this technology to generate controlled diffusivity within the tissue scaffold was examined with a directional solidified TCC sample using fluorescence recovery after photobleaching (FRAP) and scanning electron microscope (SEM). We find that the diffusion coefficient in m2/s × 10−10 is: 1.62 ± 1.27 for the unfrozen sample, 2.40 ±1.54 for the rapidly frozen sample and 9.72± 4.50 for the slow frozen sample. This points to two conclusions. One is that the diffusivity is slow frozen samples is higher than that in unfrozen samples and in rapidly frozen sample. A second observation is that a relatively narrow range of diffusivity variance was obtained when using 2%w/v sodium alginate and 2%w/v of agar. However, when the concentration of agar was reduced to 0.5w/v a much wider spread of diffusivities was measure, 4.07±1.65. This suggests that the addition of agar has also an effect on the microscale fidelity, and consequently the diffusivity. The anisotropic diffusion properties of TCC-printed directional solidification samples were also validated through both FRAP and SEM.

OBTAINING HUMATE-, NITROGEN AND MOLYBDENUM-CONTAINING LIQUID ORGANOMINERAL FERTILIZERS

The presence of humic substances (HS) and microelements in liquid organomineral fertilizers (LOMF) makes it possible to balance the mineral nutrition of plants and thereby increase the agricultural crops yield. The use of such fertilizers significantly increases the efficiency and reduces the costs of using mineral fertilizers. The aim of this work is to study the patterns of new types LOMF obtaining process, including macro- and microelements and physiologically active humic substances, and its composition and properties. Methods. Chemical analysis, inductively coupled plasma atomic emission spectrometer, infrared spectroscopy. Results and discussion. The processes of synthesis of LOMF through the interaction of sodium humate and ammonium heptamolybdate tetrahydrate were studied. Analysis of obtained results showed the same nature of the composition dependence and properties of the obtained LOMF on time. It was found that increasing the time from 10 to 120 min leads to an increase in the yield of humic acids (HAdaf) to 40.08%, the N content to 4.62% and Mo to 0.17%, the amount of COOH to 1.80 mg-eq/g and OHphen. groups – up to 0.71 mg-eq/g. It has been shown that with an increase in S:L ratio from 0.3:100 to 0.7:100, the HAdaf decreases to 36.97%, and the N and Mo contents increase, respectively, to 6.0 and 0.37%. Conclusion. The regularities of the time influence and S:L ratios on the composition and properties of LOMF samples have been established. It has been shown that an increase in time and S:L ratio contributes to an increase in the content of N and Mo, the carboxyl and phenolic hydroxyl groups. The changes in these parameters have different effects on the HAdaf. The presence of HS, N, Mo, COOH and OHphen groups in the resulting products allows them to be used in agriculture and for restoring soil fertility.

Abrasivity database of different genetic rocks based on CERCHAR Abrasivity Test

Rock abrasivity is one of the main factors affecting the wear of rock-cutting tools, which is usually quantified by the CERCHAR Abrasivity Index (CAI). Researchers and engineers study tool wear and predict tool life based on the CAI of rocks. However, there is still a lack of a dataset on rock properties, especially the abrasivity of various rocks. This paper reports the abrasive dataset of 10 kinds of rocks, including sedimentary rocks, metamorphic rocks, and igneous rocks, with the aid of the CERCHAR Abrasivity Test and digital measurement techniques. The dataset comprises rock abrasivity data, point cloud data for visualization, scratch photos, CERCHAR Abrasivity Test force data, and mechanical properties (uniaxial compressive strength) of rock samples. This dataset facilitates future research on rock abrasivity and rock-cutting tool wear.

Justification of methods for calculating and analyzing the properties of pseudorandom and random sequences based on DNA

An integral requirement for modern information systems is to provide users with services such as confidentiality, integrity, availability, and irrefutability. The quality of such services directly depends on cryptographic transformations, an important component of most of which is randomness. Therefore, the generation of pseudorandom and random sequences is one of the most relevant and important tasks in cryptography. Such sequences are generated based on physical and non-physical noise sources. Our previous studies indicate the theoretical possibility to use DNA as a noise source and, accordingly, as a source of random sequences. Any noise source "contains randomness", i.e. it has a certain amount of entropy, but a sample from such a source will not always have good properties. That is why there is a need for tools that can obtain sequences with good randomness properties of samples from the DS sequences with good randomness properties of samples from the noise source (by, for example, some kind of enhancement). Such sequences should satisfy the necessary conditions: be statistically indistinguishable, uniform, etc. NIST-approved DRBG designs can be used to guarantee this. Such constructions are most often based on strong crypto-primitives, such as hashes, HMACs, or block or stream ciphers in the required modes. This work is devoted to newly developed methods for obtaining pseudorandom and random sequences based on DNA sequences using the national standard for block symmetric encryption DSTU 7624:2014 in the counter (CTR) operation mode, as well as methods for comparing sequences (both DNA and binary). The work essentially opens the topic of obtaining random sequences based on DNA, since previous studies of DNA in cryptography have focused on the use of DNA in encryption and steganography. The paper presents the results of solving such issues as the development of methods for obtaining DNA-based sequences, the evaluation of statistical and stochastic properties of such sequences, and the evaluation of similarity based on k-mer and MinHash distances. The results obtained indicate the prospects and relevance of further research in this area.

Characterization of sodium caseinate derived from various sources: Unraveling the relationship between structure and functional properties

In this study, the structural and functional properties of laboratory-prepared sodium caseinate (L-SC) from yak Qula with three different sources of commercial products: yak milk, Qula, and milk sodium caseinate products (YM-SC, YQ-SC, M-SC) were compared. The physicochemical properties of different samples were analyzed, indicating significant fat content and color differences. The SDS-PAGE showed predominant protein subunits in the 25 kDa–35 kDa range, with M-SC having the highest κ-casein content and the least aggregation. M-SC exhibited the smallest particle size, lowest surface hydrophobicity (H0) and surface tension at the oil-water interface, with excellent functional properties, whereas YQ-SC exhibited contrast. FTIR suggested that the effect may be attributed to the decreased α-helix and β-sheet structure, and reduction in H0 and protein aggregation, resulting in a notable enhancement in protein solubility and surface activity. After optimizing the alkali extraction conditions and drying method, L-SC showed a reduced particle size of 135.0 nm, significantly improved foaming properties while the prepared emulsion had good stability and smaller d4,3. In addition, the relationship among the indicators was verified by the correlation analysis. These results could provide more information for the manufacturing of sodium caseinate in the food industry.

Exploring structural and optical properties of shock wave-loaded polycrystalline picric acid: implications for molecular engineering applications

Abstract The shock wave impact on hydrogen-bonded organic materials’ structural properties and their responses with respect to their associated functional properties is one of the most prevalent research topics because of the possible emergence of unusual functional properties. Presently, we intend to examine the structural response of the poly-crystalline picric acid samples under shocked conditions. The crystallographic structural responses and the linear optical properties of the test samples have been examined by powder XRD analysis, ultra-violet diffused reflectance spectroscopy (UV-DRS) and Raman spectroscopy, respectively. Under shocked conditions, a considerable modification in the diffraction peak positions and their intensity changes could be witnessed. Notably, linear optical transmittance profiles show remarkable changes according to the number of applied shock pulses, such that the 150-shocked sample has the highest optical transmittance of 53.9 % at 350 nm, whereas the control sample has an optical transmittance of 6.6 %. The Raman spectrum shows the vibrational groups of material that are stable in shocked conditions with similar intensity changes. Based on the obtained XRD, UV-DRS and Raman results, shock wave-induced picric acid samples have remarkably improved characteristics of optical transmittance, which is highly favorable for non-linear optical applications.

Adaptive mechanisms of dental pulp stem cells (DPSCs) in response to oral disease: Evaluating chitosan-calcium zirconium nanoparticle biomaterials for tissue engineering

This study aims to investigate the adaptive strategies employed by dental pulp stem cells (DPSCs) in response to oral disease conditions, focusing on their survival and proliferation. DPSCs possess regenerative potential and play a crucial role in the repair and regeneration of dental tissues. The study explores the coping mechanisms of DPSCs under oral disease conditions using a chitosan-based biomaterial reinforced with calcium zirconium nanoparticles (CZNP). The investigation assesses the viability and proliferation of DPSCs in the presence of oral disease conditions and evaluates the performance of the chitosan-CZNP biomaterial. The study presents the characterization and performance evaluation of drug-loaded biomaterials with varying weight percentages of CZNP. Parameters such as porosity, drug release, fracture toughness, tensile strength, degradation rate, and apatite formation are examined. The results demonstrate that increasing the weight percentage of CZNP leads to higher porosity and drug release while maintaining or enhancing fracture toughness, tensile strength, and apatite formation. Notably, the biomaterial containing 7.5 wt% CZNP exhibits the highest drug release, fracture toughness, and apatite formation. These findings suggest that the chitosan-CZNP biomaterial effectively supports the survival and proliferation of DPSCs under oral disease conditions. An artificial neural network (ANN) is employed to predict the properties of samples with different weight percentages and apatite formation. The ANN successfully estimates the degradation rate, tensile strength, fracture toughness, drug release, and porosity of the samples. This research enhances our understanding of the coping mechanisms of DPSCs and highlights the potential of chitosan-CZNP biomaterials in oral tissue engineering and regenerative medicine. Further investigations are warranted to explore the long-term effects and clinical applications of these biomaterials in the treatment of oral diseases.

ZrC/SiC composites from functionalised ZrC combining preceramic precursors and SPS

ZrC/SiC composites were obtained in situ using Spark Plasma Sintering (SPS), with a previous organic functionalisation of ZrC particles (ZrCf). It used the direct ceramisation/sintering of ZrCf/polycarbosilane mixture without any previous crosslinking steps. The prior functionalisation did not have an effect on either the relative density of the materials or the mechanical properties. However, larger SiC domains were observed around the functionalised ZrC particles, probably due to the hydrosilylation reaction between pendant alkene groups and Si-H from the commercial polycarbosilane. In addition, TEM analyses showed different features such as the presence of inter- and intra-granular SiC, and of a double layer at the grain boundaries between the ZrC and SiC phases, when avoiding functionalisation. The oxidation behaviour was also tested, and the prior functionalisation improved the properties of the final samples.

Impact of Cu2+ precursor on physical and photoelectrochemical properties of electrodeposited nanostructured CuS thin films for biosensor applications

Nanostructured CuS films were synthesized on FTO substrates employing low-cost electro deposition technique. XRD, Raman, SEM, UV–visible spectroscopy, photocurrent, PL, Mott-Schottky, and electrochemical impedance spectroscopy (EIS) measurements were used to examine physical and photoelectrochemical properties of samples. XRD results indicated that CuS films have hexagonal crystal structure where the crystallite size raises from 32 to 53 nm with increasing the Cu2+ molarity. Raman results displayed two peaks at 270 and 450 cm−1 that related to A1g transverse optical mode (TO) and A1g longitudinal optical (LO) mode for the vibrations of the S–S stretching and Cu–S bonds, respectively. SEM images displayed that fabricated CuS cover the substrate surface entirely, where grains are distributed uniformly with increasing the Cu+2 molarity. UV–visible measurements exhibited an absorption band edge between 450 and 550 nm as a characteristic of CuS films direct band gap. PL results presented strong blue-green emission at about 500 nm for CuS thin films. The photocurrent studies demonstrated that the CuS films are p-type semiconductors where the current density increases from 0.8 mA/cm2 to 1.1 mA/cm2 with the Cu2+ molarity increasing. The EIS analysis confirmed that charge transfer resistance reduces with increasing molarity. Mott- Schottky measurements established that carrier concentrations and the flat band varied from 5 × 1019 to 6.7 × 1019 cm−3 and from 1.1 to 0.75V, respectively. The fabricated CuS film was tested as glucose biosensor where a fast response and higher stability were noticed. Our results indicated that nanostructured CuS films are gifted candidates for optoelectronics applications especially biosensors.