Acrylic Acid Research Articles

Prussian Blue Encapsulated with Brush-like Polyorganosiloxane Nanospheres with Tunable Functionality

Faced with higher demands of pigments in various applications, the performance of pigments in a specific system is in urgent need of optimization and improvement. Polyorganosiloxane (POS) stands out among various encapsulating polymeric materials for pigment modification due to its superior thermal stability and alkali resistance. However, the inherent hydrophobicity of POS causes poor stability in aqueous systems, which is usually applied in environmentally friendly applications. Grafting hydrophilic polymer chains on the surface of POS could improve water dispersity. In addition, the encapsulated pigment can also be endowed with various functionalities by selecting or combining grafted polymers. Herein, we reported a strategy to encapsulate Prussian blue (PB27) with POS grafted with poly(acrylic acid) (PAA) or poly(N-(2-hydroxyethyl) acrylamide) (PHEAA) to allow better stability and functionality of the composite pigment particles, denoted as PB27@POS@PAA or PB27@POS@PHEAA, respectively. The effect of the number of monomers and the amount of initiator potassium persulfate (KPS) on the brush thickness of the grafted polymers was studied, along with various performance properties and the functionality of PB27@POS@PAA and PB27@POS@PHEAA. The dispersity, alkali resistance, and high-temperature stability are studied. The brush-like composite pigment performs better after centrifugation (5000 rpm, 30 min) or treatment under 90 °C when the dosage of grafting monomer AA or HEAA reaches 400 wt%. Optimal alkali resistance was obtained for PB27@POS@PAA (AA, 200 wt%) with a particle size variation of only 31 nm after 8 h. Comparably, PB27@POS@PHEAA behaved worse under similar conditions. Moreover, PB27@POS grafted with PAA was responsive to pH and that with PHEAA showed excellent antifouling properties, which could also be replaced by other functional monomers if needed.

Multi-omic integration reveals alterations in nasal mucosal biology that mediate air pollutant effects on allergic rhinitis.

Allergic rhinitis is a common inflammatory condition of the nasal mucosa that imposes a considerable health burden. Air pollution has been observed to increase the risk of developing allergic rhinitis. We addressed the hypotheses that early life exposure to air toxics is associated with developing allergic rhinitis, and that these effects are mediated by DNA methylation and gene expression in the nasal mucosa. In a case-control cohort of 505 participants, we geocoded participants' early life exposure to air toxics using data from the US Environmental Protection Agency, assessed physician diagnosis of allergic rhinitis by questionnaire, and collected nasal brushings for whole-genome DNA methylation and transcriptome profiling. We then performed a series of analyses including differential expression, Mendelian randomization, and causal mediation analyses to characterize relationships between early life air toxics, nasal DNA methylation, nasal gene expression, and allergic rhinitis. Among the 505 participants, 275 had allergic rhinitis. The mean age of the participants was 16.4 years (standard deviation = 9.5 years). Early life exposure to air toxics such as acrylic acid, phosphine, antimony compounds, and benzyl chloride was associated with developing allergic rhinitis. These air toxics exerted their effects by altering the nasal DNA methylation and nasal gene expression levels of genes involved in respiratory ciliary function, mast cell activation, pro-inflammatory TGF-β1 signaling, and the regulation of myeloid immune cell function. Our results expand the range of air pollutants implicated in allergic rhinitis and shed light on their underlying biological mechanisms in nasal mucosa.

A Real‐Time Display Screen Based on Organohydrogel with Tunable Fluorescence

AbstractIn this study, a multi‐monomer organohydrogel network is fabricated based on radical polymerization. Acrylic acid (AA) and dimethylaminoethyl methacrylate (DMAEMA) are used as hydrophilic monomers, and methoxyethyl acrylate (MEA) serves as a hydrophobic monomer. To endow the organohydrogel with a photo‐responsive property, a fluorescent monomer, 1′‐acryloyl chloride‐3′,3′‐dimethyl‐6‐nitrospiropyran (SPMA) is added. Under ultraviolet (UV) and visible light irradiation, SPMA undergoes ring‐opening and ring‐closing isomerization reactions, respectively. This leads to enhanced and reduced fluorescence. This fluorescence tunability allows for the local regulation of fluorescence in the organohydrogel using a photomask. By employing UV and visible light, complex information can be repeatedly written and erased on the organohydrogel. Additionally, based on the interactions between dimethyl sulfoxide (DMSO) and water within the system, the organohydrogel exhibits excellent anti‐freezing and water‐holding properties, allowing its use in low‐temperature environments and extended preservation time. The organohydrogel has precise information writing capabilities and is more difficult to falsify as an information encryption platform. This study provides guidance for future researchers to develop information writing capabilities with higher precision and broader applications in various environments using smart materials.

Hydrogels composite optimized for low resistance and loading–unloading hysteresis for flexible biosensors

With the advancement of wearable and implantable medical devices, hydrogel flexible bioelectronic devices have attracted significant interest due to exhibiting tissue-like mechanical compliance, biocompatibility, and low electrical resistance. In this study, the development and comprehensive performance evaluation of poly(acrylic acid)/ N,N′-bis(acryloyl) cystamine/ 1-butyl-3-ethenylimidazol-1-ium:bromide (PAA/NB/IL) hydrogels designed for flexible sensor applications are introduced. Engineered through a combination of physical and chemical cross-linking strategies, these hydrogels exhibit strong mechanical properties, high biocompatibility, and effective sensing capabilities. At 95 % strain, the compressive modulus of PAA/NB/IL 100 reach up to 3.66 MPa, with the loading–unloading process showing no significant hysteresis loop, indicating strong mechanical stability and elasticity. An increase in the IL content was observed to enlarge the porosity of the hydrogels, thereby influencing their swelling behavior and sensing functionality. Biocompatibility assessments revealed that the hemolysis rate was below 5 %, ensuring their suitability for biomedical applications. Upon implantation in rats, a minimal acute inflammatory response was observed, comparable to that of the biocompatibility control poly(ethylene glycol) diacrylate (PEGDA). These results suggest that PAA/NB/IL hydrogels hold promise as biomaterials for biosensors, offering a balance of mechanical integrity, physiological compatibility, and sensing sensitivity, thereby facilitating advanced healthcare monitoring solutions.

Porous sodium alginate/poly (acrylic acid) composites cross-linked with FeCl3 for acid black 1 dye removal from aqueous solution

This study developed a polymeric composite, sodium alginate (SA)/poly (acrylic acid) (PAA) cross-linked with FeCl3 (SA/PAA-Fe), for its function as adsorbent to eliminate acid black 1 dye (AB1) from an aqueous solution. The structural analysis of SA/PAA-Fe revealed a porous structure. To comprehensively evaluate the adsorption of AB1 onto SA/PAA-Fe and gain insight into its mechanism, we examined the effects of solution’s pH, initial dye concentration, adsorbent dosage, contact time, and adsorption temperature. The best adsorption conditions for achieving a highly effective removal percentage of 95.43 % were a pH of 8.9, contact period of 90 min, and a temperature of 45 °C. Pseudo-second-order and Langmuir models were fitted for the isotherm and kinetic model parameters, respectively. Thermodynamic analyses strongly suggested that the adsorption process occurred was endothermic and spontaneous. The adsorption of AB1 was primarily observed on the solid surface, as confirmed by the SEM-EDS and FTIR measurements.

A non-spherical nanoparticles system for the delivery of peptides using polymer grafted nanocellulose

AbstractPeptide drugs are increasingly used to treat a variety of diseases ranging from cancer, and infections to cardiovascular diseases. However, peptides can suffer from low stability in the bloodstream. Entrapment of peptides into nano-sized carriers of various types has widely been explored, but all of them have spherical shapes. Nanocellulose can in contrast serve as a non-spherical nanoparticle with a high aspect ratio. After the isolation of nanocellulose by TEMPO-mediated oxidation, the material needs to be modified with polymers to generate nanoparticles with high water-solubility that can also favourably interact with peptide drugs. We have here chosen insulin as the model drug, which can strongly interact with cationic polymers. As it is known that cationic polymer may retain charged drugs too tightly, we have selected poly(2-(dimethylamino)ethyl acrylate) PDMAEA as a degradable polymer that undergoes self-hydrolysis to poly(acrylic acid) in water. This polymer was compared to poly(N-(3-(dimethylamino)propyl) acrylamide) PDMAPAA, which is a stable cationic polymer. The cationic polymer was co-grafted with poly(2-hydroxyethyl acrylate) PHEA as a water-soluble neutral polymer using the three-component Passerini reaction. A combination of fluorescence and UV-Vis techniques were used to quantify the amount of polymer that was conjugated to the surface. The polymer-coated nanocellulose was labelled with the fluorescent cyanine dye Cy5 while insulin was labelled with Cy3 creating a FRET system that allows monitoring of the interaction between insulin and polymer in cell growth media. We observed that despite the self-hydrolysis of PDMAEA into a negatively charged polymer, the negatively charged insulin was not released in buffer solution according to the FRET studies. Only the addition of serum-supplemented cell growth media led to insulin release. The limited release was explained with the fact that insulin, as well as other peptides, have a mixture of negative and positive charges, with the pH value and the isoelectric point determining the balance between both. Negative-charged polymers can therefore still interact favourably with negatively charged peptides by interacting with cationic amino acids. Graphical Abstract

Green Fabrication of Superhydrophilic/Underwater Superoleophobic Composite Membrane for High-Efficiency Oil/Water Separation in Harsh Environments.

Due to the high oil spill incidence and industrial wastewater discharge including oil and emulsified oil, designing and synthesizing oil-water separation materials which can maintain stability under harsh environmental conditions with high separation efficiencies remains a great challenge. The present work developed an easy, green, cost-effective, and easily scaled-up approach for fabricating cellulose-based membranes. First, we coated polydopamine (PDA) onto fibers of filter membrane (FM). Then, the PDA-FM membrane was immersed into the mixed solution of poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) and further thermally cross-linked at 150 °C to create a superhydrophilic/underwater superoleophobic membrane (PVA/PAA@PDA-FM) to separate oil/water mixtures. The simple thermally cross-linking process promotes multiple covalent chemical bonds generation between cellulose filter membrane, PAA, PDA, and PVA, endowing membranes with excellent stability and resistance to acidity, alkalinity, and salinity. The PVA/PAA@PDA-FM membrane not only demonstrates great separation performance (>99.8%) and great flux (>1000 L m-2 h-1) in oil-water immiscible mixtures but also maintains high separation efficiency under conditions of high acidity, alkalinity, and salinity. Additionally, the PVA/PAA@PDA-FM membrane exhibits excellent separation capacity in oil-water emulsions, which can maintain the >99.6% separation efficiency even after 40 cycles in harsh environments, showing outstanding reusability. Thus, due to the multiple cross-linked networks in the membrane, the excellent performance makes the PVA/PAA@PDA-FM membrane a good application prospect in water purification and oily wastewater treatment.

Essential Oil and Smoke Components of Artemisia absinthium and Hagenia abyssinica.

Hagenia abyssinica and Artemisia absinthium are widely distributed tree species in Ethiopia and known for their traditional medicinal uses. The present study was conducted to determine the essential oil and smoke constituents of H. abyssinica and A. absinthium leaves using GC-MS. The main components of the A. absinthium essential oil were valencene (5.48%), bornyl acetate (5.15%), and trans-cinnamic acid (4.34%). 2-Bornanone (18.54%), o-cymene (12.80%), and nerolidol (7.04%) were the dominant components of the MeOH fraction of the smoke derived from the leaves of A. absinthium, while 2-propenoic acid butyl ester (46.49%), heptadecane (10.66%), and 9-octylheptadecane (7.78%) were the major components of the n-hexane fraction. The main components of the H. abyssinica essential oil were cis-davanone (14.73%), Aristolediene (9.31%), and cryptone (6.50%). β-Myrcene (12.59%), neophytadiene (11.54%), and limonene (11.27%) were the dominant components of the MeOH fraction of the smoke derived from the leaves of H. abyssinica. 1,3,5,7-Cyclooctatetraene (33.58%), prehnitene (7.01%), and heptadecane (5.46%) were the dominant components of the n-hexane fraction of the smoke derived from the leaves of H. abyssinica. The smoke components of A. absinthium and H. abyssinica were reported here for the first time.

Shape Dependence of Photoresponsive Molecular Crystals Composed of Naphthyl Acrylic Acid Stimulated by Solid-State [2 + 2] Photocycloaddition

Photomechanical molecular crystals, actuated by solid-state photochemical reactions, manifest a spectrum of mechanical motions upon light exposure, underscoring their prospective integration into the next generation of intelligent materials and devices. Utilizing the solid-state photodimerization of naphthyl acrylic acid as a paradigm, this study delved into the interplay between crystal morphology and reaction dynamics on the photomechanical responses of molecular crystals. Distinct crystal forms—bulk, microrods, and microplates—were cultivated through tailored crystallization conditions. While bulk crystals of naphthyl acrylic acid (NA) underwent shattering and splintering upon UV light exposure, the microplate counterparts displayed unique cracking patterns with fissures yet retained their overall structural integrity. In contrast, NA microrods underwent pronounced bending under identical irradiation conditions. These phenomena are attributed to the efficient lattice reconfiguration stemming from the [2 + 2] cycloaddition photochemical reaction within the crystals. An intermediate fluorescence enhancement was observed across all crystal types upon light exposure. Collectively, our results underscore the pivotal role of crystal shape in dictating photomechanical behavior, thereby heralding novel strategies for developing advanced photomechanical materials.

Mechanically robust, stretchable and environmentally adaptable organohydrogels with cross-linked fibrous structure for sensory artificial skins

Hydrogels are promising materials for fabricating sensory artificial skins (SASs), but their mechanical properties and environment adaptability are often limited, leading to restricted performances of SASs. In this work, mechanically robust, stretchable and environment adaptable organohydrogels with cross-linked fibrous structure are designed and constructed. The organohydrogels are prepared by introducing doped polyaniline (PANI) into cross-linked fibrous mats of poly(acrylic acid) (PAA) and poly(vinyl alcohol) (PVA). Cross-linked PAA-PVA mat works as skeleton to account for the mechanical robustness while PANI serves as the conductive component to achieve mechanosensing functionality. Due to the unique structure, the resultant organohydrogels, being denoted as PAA-PVA/PANI organohydrogels, exhibit high tensile strength (5.06 MPa), stretchability, fatigue resistance and excellent environment adaptability (anti-freezing, anti-drying and swelling resistance). SASs of such organohydrogels have achieved a gauge factor of 1.81, a sensing range of 0–70 %, a response time of 0.28 s and a reversible sensing in more than 2,000 cycles. In addition, SASs are further attempted in monitoring diverse human motions and physiological activities, such as joint bending, muscle motion and pulse. Overall, this work has provided promising soft materials for future SASs that work properly under complicated environmental conditions.

Non‐isocyanate polyurethane‐acrylate as UV‐ and thermo‐responsive plasticizer for thermoplastic elastomer

AbstractA UV‐ and thermo‐responsive polyurethane‐acrylate prepolymer was synthesized from palm olein (POo) via a non‐isocyanate route. The process included epoxidation of POo, carbonation of epoxidized palm olein (EPOo) into polycyclic carbonate in a solvent‐free and mild condition (100°C, 1 atm), followed by reacting with ethylene diamine and acrylic acid. The chemical structure of the non‐isocyanate polyurethane‐acrylate (NIPUA) prepolymer was elucidated by 1H and 13C nuclear magnetic resonance (NMR) and Fourier transform‐infrared spectroscopy (FTIR), while weight average molecular weight of NIPUA was determined by gel permeation chromatography (GPC). The NIPUA (0–20 wt%) was incorporated with thermoplastic elastomer (TPE) as a plasticizer and cured under UV light and thermal stimulations. The cured NIPUA/TPE films were characterized by FTIR, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and tensile strength test. Under UV and thermal stimulations, the NIPUA/TPE demonstrated enhanced tensile properties (elongation at break >1280%, Young's modulus ~25 MPa), thermal properties (lower Tg), lower water contact angle, and shortened curing time as compared with the blank TPE. The 20 wt% NIPUA/TPE films exhibited susceptibility to enzymatic biodegradation and noncytotoxic to HEK 293 cells in vitro, demonstrated it's potential as a UV‐ and thermo‐responsive plasticizer for TPE in manufacturing of medical devices.

Optimization of preparation conditions and performance of a new degradable soil water retaining agent

Using polyaspartic acid (PAsp) and bentonite (BT) as the main raw materials, a new type of degradable soil water retaining agent (PAsp-AA/BT) was synthesized by microwave radiation. The optimum synthesis conditions and comprehensive properties of PAsp-AA/BT were discussed and the structure and surface characteristics of PAspsp-AA/BT were characterized by FTIR, SEM, XRD and TGA in the paper. The results showed that the optimum synthesis conditions of PAsp-AA/BT were as follows: the dosages of polyaspartic acid (PAsp), bentonite (BT), initiator potassium persulfate, crosslinking agent N,N′-methylene bisacrylamide was 5, 3, 0.3, 0.03%, respectively, the neutralization degree of acrylic acid was 75%, and the microwave power was 490W. Under this condition, the absorption ratio of the synthesized PAspsp-AA/BT in deionized water and 0.9% NaCl solution was 953 and 164 g/g, respectively. The synthesized PAsp-AA/BT had a high water absorption rate, good water retention and repeated water absorption, and the degradation rate in soil within 30 days reached 32.75%, with good degradation effect. The analysis of SEM, FT-IR, XRD and TGA showed that: the surface of PAsp-AA/BT was rough and had obvious pore structure, which was conducive to the diffusion of water molecules; polyaspartic acid, bentonite and acrylic acid were polymerized; the cross-linking structure was formed between polyaspartic acid, bentonite and acrylic acid; the product of PASP-AA/BT had good thermal stability. This study provides a new soil water retaining agent, which is helpful for the better development of soil water retaining agent research.

Electrostimulated reversible swelling/shrinking behavior of electroactive p(AA-BAC)/Cu(II) microgel monolayer on Au electrode surface

Electroactive, electrosensitive and fast reacting p(AA-BAC)/Cu(II) microlayers were successfully constructed on the Au electrode surface. The layers consisted of microgel particles composed of poly(acrylic acid) cross-linked with N,N-bis(acryloyl)cystamine (BAC). The p(AA-BAC) microgels were synthesized using distillation precipitation polymerization. The deposition of microgels was due to chemisorption of -S-S- groups from BAC on the gold surface. After the deposition, copper(II) ions were added and bound with the polymer network through the coordination bonds with the carboxylic groups. This addition increased the number of crosslinking points in the gel. The microgel particles were characterized using SEM, QCM-D, dynamic light scattering and electrochemistry. Thanks to reversibility of the electroreduction and electrooxidation of the copper ions (from Cu(II) to Cu(I) and from Cu(I) to Cu(II)) the obtained layers of p(AA-BAC)/Cu(II) microparticles on gold could undergo multiple fast swelling and shrinking processes triggered by application of appropriate sequence of potentials.

DFT investigation for the mechanisms of γ-butyrolactones from styrene and acrylic acid, catalyzed by NMA*BF4 and PhSSPh

The reaction mechanisms of γ-butyrolactones through electrophilic addition reactions between styrene and acrylic acid, catalyzed by the 9-mesityl-10-methylacridinium ion (NMA*BF4) and diphenyl disulfide (PhSSPh) under 450 nm visible-light, were investigated by employing M06-2X-D3/ma-def2SVP method and basis set. In this study, the SMD model was taken to simulate the solvent effect of dichloromethane. The photocatalyst NMA absorbs the energy of photons and becomes an excited state, capturing an electron from styrene; this leads to an electrophilic addition reaction happened between the obtained styrene cationic radical and acrylic acid anion (or acrylic acid molecule); finally, an intramolecular ring-closure process and H-shift process result in the formation of the final product. The computational results point out that the electrophilic reaction is an exothermic process; and the optimal path for ring-closure reaction and H-shift reaction has Gibbs free energy barriers of 11.10 and 9.94 kcal/mol, respectively. In particular, the recycling of the photo-catalyst NMA and cocatalyst PhSSPh has also been discussed. The ρhole and ρele can reveal the charge transfer process during the photo-catalytic reaction. Results would provide valuable insights into these types of interaction and related processes.

Poly(acrylic acid)/Poly(vinyl alcohol) Microarray Patches for Continuous Transdermal Delivery of Levodopa and Carbidopa: In Vitro and In Vivo Studies.

Levodopa (LD) has been the most efficacious medication and the gold standard therapy for Parkinson's disease (PD) for decades. However, its long-term administration is usually associated with motor complications, which are believed to be the result of the fluctuating pharmacokinetics of LD following oral administration. Duodopa® is the current option to offer a continuous delivery of LD and its decarboxylase inhibitor carbidopa (CD); however, its administration involves invasive surgical procedures, which could potentially lead to lifelong complications, such as infection. Recently, dissolving microarray patches (MAPs) have come to the fore as an alternative that can bypass the oral administration route in a minimally invasive way. This work explored the potential of using dissolving MAPs to deliver LD and CD across the skin. An acidic polymer poly(acrylic acid) (PAA) was used in the MAP fabrication to prevent the potential oxidation of LD at neutral pH. The drug contents of LD and CD in the formulated dissolving MAPs were 1.82 ± 0.24 and 0.47 ± 0.04 mg/patch, respectively. The in vivo pharmacokinetic study using female Sprague-Dawley® rats (Envigo RMS Holding Corp, Bicester, UK) demonstrated a simultaneous delivery of LD and CD and comparable AUC values between the dissolving MAPs and the oral LD/CD suspension. The relative bioavailability for the dissolving MAPs was calculated to be approximately 37.22%. Accordingly, this work highlights the use of dissolving MAPs as a minimally invasive approach which could potentially bypass the gastrointestinal pathway and deliver both drugs continuously without surgery.

Enhanced luminescent properties of poly(sodium acrylate)-based composite and its selective interaction towards copper ions

This study investigates the luminescent properties and metal ion interactions of europium when combined with a polymer chain of poly (sodium acrylate) (PSA) and a phenanthroline (Phen) molecule, which acts as an efficient antenna. The study of interactions between lanthanide ions and various compounds in different matrices is crucial, providing valuable insights into the molecular environment, and enabling a deeper understanding of processes affecting their luminescence. In this study, we investigated the luminescent properties of the Eu(PSA)Phen complex and its remarkable capacity for selective interaction with Cu2+ ions in an aqueous solution. From this selective interaction, we conducted a series of detailed studies that provided valuable insights into the mechanisms of luminescence suppression, information about the europium chemical environment, and other related aspects. The luminescence of Eu(PSA)Phen is significantly quenched by Cu2+ ions, driven by both static and dynamic mechanisms. The presence of the PSA polymer chain and Phen molecules within the composite exerts a profound influence on energy transfer processes, enabling selective responses to Cu2+ ions, even in the presence of competing cations. Additionally, we observed a preferential interaction of the PSA molecule in the Eu(PSA)Phen composite with Cu2+ ions over the N groups of phenanthroline. These findings underscore the compound potential as a versatile tool in various fields, ranging from material science to biosensing, where rapid and selective metal ion detection is of paramount importance.

Creating value added nano silicon anodes from end-of-life photovoltaic modules: recovery, nano structuring, and the impact of ball milling and binder on its electrochemical performance

Recovery of silicon from end-of-life photovoltaic (PV) modules, purification, conversion to nano silicon (nano-Si), and subsequent application as an anode in lithium-ion batteries is challenging but can significantly influence the circular economy. Currently, a complete technology consisting of cross-contamination-free recovery of silicon wafers from end-of-life PV modules, a low-cost environmentally friendly purification process of the recovered PV silicon, a high yield conversion process of the recovered PV silicon into nano-Si, and its subsequent application in lithium-ion batteries is unavailable. This study provides a complete package including cross-contamination-free recovery, economical purification, reliable conversion to nano-Si, and efficient application of the end-of-life PV nano-Si in lithium-ion batteries. Hydrofluoric acid-free recovery and purification processes are demonstrated which can deliver large quantities of high-purity (≥ 99) silicon. In addition, the subsequent ball milling process produces very distinct nano-Si with different shapes and sizes. This study also creates a very effective nano-Si anode through in-situ crosslinking of water-soluble carboxymethyl cellulose and poly (acrylic acid) precursors. The integration of distinct PV nano-Si and water-soluble carboxymethyl cellulose-poly (acrylic acid) crosslink binder opens distinct possibilities to develop silicon-based practical anode for next generation low-cost lithium-ion batteries to power cell phones to electric vehicles.

Hybrid Water-Harvesting Channels Delivering Wide-Range and Supersensitive Passive Fluorescence Humidity Sensors.

The development of optical humidity detection has been of considerable interest in highly integrated wearable electronics and packaged equipment. However, improving their capacities for color recognition at ultralow humidity and response-recovery rate remains a significant challenge. Herein, we propose a type of hybrid water-harvesting channel to construct brand-new passive fluorescence humidity sensors (PFHSs). Specifically, the hybrid water-harvesting channels involve porous metal-organic frameworks and a hydrophilic poly(acrylic acid) network that can capture water vapors from the ambient environment even at ultralow humidity, into which polar-responsive aggregation-induced emission molecules are doped to impart humidity-sensitive luminescence colors. As a result, the PFHSs exhibit clearly defined fluorescence signals within 0-98% RH coupling with desirable performances such as a fast response rate, precise quantitative feedback, and durable reversibility. Given the flexible processability of this system, we further upgrade the porous structure via electrostatic spinning to furnish a kind of Nano-PFHSs, demonstrating an impressive response time (<100 ms). Finally, we validate the promising applications of these sensors in electronic humidity monitoring and successfully fabricate a portable and rapid humidity indicator card.

Janus Membrane-Based Wearable pH Sensor with Sweat Absorption, Gas Permeability, and Self-Adhesiveness.

Wearable biomedical sensors have enabled noninvasive and continuous physiological monitoring for daily health management and early detection of chronic diseases. Among biomedical sensors, wearable pH sensors attracted significant interest, as pH influences most biological reactions. However, conformable pH sensors that have sweat absorption ability, are self-adhesive to the skin, and are gas permeable remain largely unexplored. In this study, we present a pioneering approach to this problem by developing a Janus membrane-based pH sensor with self-adhesiveness on the skin. The sensor is composed of a hydrophobic polyurethane-polydimethylsiloxane porous hundreds nanometer-thick substrate and a hydrophilic poly(vinyl alcohol)-poly(acrylic acid) porous nanofiber layer. This Janus membrane exhibits a thickness of around 10 μm, providing a conformable adhesion to the skin. The simultaneous realization of solution absorption, gas permeability, and self-adhesiveness makes it suitable for long-term continuous monitoring without compromising the comfort of the wearer. The pH sensor was tested successfully for continuous monitoring for 7.5 h, demonstrating its potential for stable analysis of skin health conditions. The Janus membrane-based pH sensor holds significant promise for comprehensive skin health monitoring and wearable biomedical applications.

Rapid, Micron-Resolution 3D Printing of Nd:YAG Ceramic with Optical Gain.

Polycrystalline yttrium aluminum garnet (YAG) ceramic doped with neodymium (Nd), referred to as Nd:YAG, is widely used in solid-state lasers. However, conventional powder metallurgy methods suffer from expenses, time consumption, and limitations in customizing structures. This study introduces a novel approach for creating Nd:YAG ceramics with 3D free-form structures from micron (∼70µm) to centimeter scales. Firstly, sol-gel synthesis is employed to form photocurable colloidal solutions. Subsequently, by utilizing a home-built micro-continuous liquid interface printing process, precursors are printed into 3D poly(acrylic acid) hydrogels containing yttrium, aluminum, and neodymium hydroxides, with a resolution of 5.8µm pixel-1 at a speed of 10µm s-1. After the hydrogels undergo thermal dehydration, debinding, and sintering, polycrystalline Nd:YAG ceramics featuring distinguishable grains are successfully produced. By optimizing the concentrations of the sintering aids (tetraethyl orthosilicate) and neodymium trichloride (NdCl3), the resultant samples exhibit satisfactory photoluminescence, emitting light concentrated at 1064nm when stimulated by a 532nm laser. Additionally, Nd:YAG ceramics with various 3D geometries (e.g., cone, spiral, and angled pillar) are printed and characterized, which demonstrates the potential for applications, such as laser and amplifier fibers, couplers, and splitters in optical circuits, as well as gain metamaterials or metasurfaces.