Short Crack Propagation Research Articles

Advancing the understanding of short fatigue crack propagation: Leveraging ultrasonic testing device to approach rolling contact fatigue

Advancing the understanding of short fatigue crack propagation: Leveraging ultrasonic testing device to approach rolling contact fatigue

Critical damage events of 3D printed AlSi10Mg alloy via in situ synchrotron X-ray tomography

Fish-scale-like melt pool structures and internal defects are characteristic features in additively manufactured (AM) metals. These play a critical role in the damage and fracture processes under different service loading conditions. However, the relationship between these damage features and loading conditions, as well as the spatial interactions between melt pool structures and internal defects remains poorly understood. Using in situ time-lapse synchrotron X-ray tomography and diffraction, we identify the initiation and growth events of life-limiting damage under tensile, low cycle fatigue (LCF), and high cycle fatigue (HCF) loading. A novel transition from meso-structure insensitive, defect-dominated short fatigue crack propagation to a meso-structure sensitive mechanism occurs as the plastic zone expands ahead of a growing crack from HCF to LCF to tensile loading. Under tension and LCF, the damage accumulation gradually increases and micro-voids nucleate at the melt pool boundaries (MPBs) after which the crack path follows the MPBs. In contrast, under HCF, surface defects initiate fatigue cracking and the MPBs have a very limited effect on the crack propagation path. Finally, a physics-informed machine learning method is introduced to develop a novel methodology for predicting fatigue life by including three-dimensional features of defects in AM parts.

Crack propagation behavior of different zones in weldment under creep-fatigue loadings

In this paper, crack propagation behaviors in a weldment are simulated under cyclic loadings using crystal plasticity finite element coupled with the XFEM. The result shows that the cracks in heat affected zone grow faster than that in the welded zone. Short crack propagation dominated by dislocation activity takes approximately 4 to 5 grains, followed by long crack propagation which is unrelated to dislocation activity and the growth direction kept an angle to the loading direction (45°-51°). Experimentally observed deflections within grains and at grain boundaries, retardation at grain boundaries are captured by the simulation.

Short fatigue crack growth and retained austenite in steels processed via quenching and partitioning

Previous research has consistently found that introducing metastable retained austenite (RA) as a second phase retards the failure of steel under fatigue. However, the reasons for this benefit are not understood. Accordingly, the properties of RA most advantageous to resist fatigue are not known. Within this context, this paper examines the interaction between second-phase RA and short fatigue crack growth in a steel processed via quenching and partitioning, using quasi in situ electron backscatter diffraction experiments. Results show that most RA transforms into martensite under the plastic strain surrounding the crack. They also reveal various mechanisms whereby RA transformation delays short fatigue crack propagation; transformation-induced crack closure (TICC), crack deflection and branching, and roughness-induced crack closure (RICC). Crack deflection and branching are driven by a tendency of cracks to propagate towards transformed RA, which is against the previous assumptions in the literature. Furthermore, the impact of crack deflection/branching on retardation is more powerful than that of TICC acting alone. Microstructures including second-phase RA should avoid RA-lean areas and promote elongated RA grains, with relatively large size, and major axis normal to the preferential crack growth direction. Untransformed RA within the plastic zone (i.e. overstabilized) does not contribute to crack retardation.

Fatigue fracture of 316L steel manufactured by selective laser melting method

The kinetics of short cracks in 316L steel samples made by selective laser melting was studied. The structural sensitivity of such cracks, which form on technological defects at the early stage of fatigue is noted. The cracks develop predominantly along the fusion boundaries and slow down their growth at the boundaries of the melt pools. An increase in the crack opening of arrested cracks lead to the formation of a plastic zone at their tips, localization of deformation, a decrease in opening and continued growth with an increase in the number of cycles. The alternation of the processes of propagation and deceleration of short cracks during loading is reflected in the kinetic diagram of fatigue failure which has rate growth thresholds with spacing between them being close to the scanning step during steel manufacturing. The diagram is described by the Paris equation with the same exponent at the growth stage of both short and long cracks. The plotted fatigue curve was compared with fatigue curves for the same material produced by traditional and additive methods. It was shown that the plotted fatigue curve, as well as the fatigue curves for similar materials taken from literary sources, lie much lower than the fatigue curve for the same steel obtained by the traditional method. However, the use of optimal manufacturing modes, as well as subsequent heat treatment, leads to the fatigue characteristics of «additive» steel being similar to those of steels produced by the traditional method. The macro- and microrelief of the fracture surfaces of the samples was studied, the stages of stable and accelerated crack growth were identified, the crack lengths at fracture surfaces corresponding to these stages were evaluated and the predominate fracture mechanisms at each stage were described. It is shown that the observed knee point in the fatigue curve is accompanied by an increase in the damage of the lateral surface of the samples with an increase in the stress amplitude and transition to a more ductile fracture relief, which is explained by the switch from the plane-strain state to a plane-stressed state of the sample material realizing at the tip of the macrocrack.

Torsional fatigue behaviour and damage mechanisms of martensitic spring steel in the HCF regime

This study investigates the fatigue behaviour and damage mechanisms of the martensitic spring steel SAE 9254, with emphasis on short crack propagation. Shear stress-controlled torsional fatigue tests are performed at stress ratio R = -1 and test frequency f = 79 Hz using structure-sensitive measurement techniques to detect the relevant damage mechanisms. An in-situ torsional fatigue testing device is applied for shear-controlled fatigue tests at two amplitudes of the torsion angle using R = –1 and f = 5 Hz, and the microstructural-dependent short crack propagation path is documented by means of confocal laser microscopy and electron backscattering analysis. It is found that the early development of fatigue damage is characterised by the formation of slip bands, which serve as crack initiation sites. In this process, crack initiation occurs preferentially at or near prior austenite grain boundaries. Furthermore, prior austenite grain boundaries were identified as obstacles for the propagation of short cracks, because of the change of the crystallographic orientation leading to an oscillating propagation rate of short cracks. The short crack density ρCD, which is an important parameter for fatigue damage, is rapidly growing with increasing shear stress amplitude ΔτT/2 and reveals a stress type specific behaviour.

Effect of loading conditions on short fatigue crack propagation behaviours in cast Al[sbnd]Si alloys

The effect of loading conditions on short crack propagation behaviours in cast AlSi alloys was investigated by a combination of photo-microscopy monitoring and post mortem analysis. The findings suggest that the path of short cracks is minimally influenced by loading conditions, whereas loading conditions significantly affect the fatigue crack growth rate (FCGR) and its statistical characteristics. Crack closure effect is observed under zero and negative stress ratio conditions. Roughness-induced crack closure occurs due to the coarse grain microstructure of cast AlSi alloys and the Stage-I mode growth of cracks within grains in the microstructural short crack regime. The high level of plasticity around the crack tip under negative stress ratio conditions has a significant impact on FCGR, resulting in a negative crack opening stress. When the stress ratio exceeds approximately 0.3, short cracks exhibit no crack closure. The load-level effect is observed only at high load conditions with negative stress ratios. Finally, a probabilistic short crack growth model was established using a Bayesian linear regression model to analyse the effect of stress ratio on the uncertainty of FCGR. After considering the crack closure effect, the difference in distributions of FCGR model parameters decreases significantly among different stress ratio conditions.

Corrosion fatigue mechanisms and evaluation methods of high‐strength steel wires: A state‐of‐the‐art review

AbstractCorrosion significantly degrades the fatigue performance of high‐strength steel wires. This study conducts an extensive review of corrosion fatigue in corroded steel wires based on relevant literature. It outlines corrosion fatigue evolution mechanisms and discusses various test methodologies. Six distinct approaches are employed to assess corrosion fatigue life. A three‐stage multiscale corrosion fatigue evolution process involves pitting formation and growth, short crack propagation, and long crack propagation. Advanced fatigue assessment methods like the theory of critical distances (TCD) and the strain energy density (SED) are explored for predicting the corrosion fatigue life for corroded steel wires. A model utilizes an elastoplastic corrosion fatigue damage framework to comprehensively represent the complex interactions. The physics‐data‐driven method has garnered increasing attention due to its requirement of fewer sample data and good robustness. Moreover, the reliability method underscores its pivotal role in guaranteeing the longevity of suspenders and cables in practical settings.

Analysis of the crack initiation and short crack propagation of laser cladding IN718 enduring fretting fatigue at 650 ℃

In order to reveal the behaviors of crack initiation and short fatigue crack propagation in laser cladding IN718 under high temperature conditions, very high cycle fretting fatigue (VHCFF) experiments were conducted at 650 ℃ with a transverse clamping force of P=400N and different axial stress loading conditions to obtain S_N data. The surface wear morphology and fracture morphology characteristics were analyzed by scanning electron microscope (SEM) and white light interferometer. Additionally, the microstructure characteristics of grains in the short fatigue crack region were examined through electron back scatter diffraction (EBSD). Parameters such as equivalent grain size, grain elastic modulus, Schmid factor, geometric compatibility factor, twist angle, and tilt angle were considered in the analysis of the characteristics of fatigue crack initiation and propagation. The results indicate that fretting fatigue cracks tend to initiate on grains with higher Schmid factors, larger equivalent grain size, and lower grain elastic modulus on the fretting contact surface. Moreover, the short fatigue cracks tend to propagate along the grains with the microstructural features of the high Schmid factor, the geometric compatibility factor of m′>0.4, the twist angle of α<50°, and the tilt angle of β<50°.

Residual stress effects on short crack propagation behavior in friction stir welded 7075-T6 aluminum alloy panel under biaxial loading: An experimental and numerical study

The effects of residual stress on short crack propagation behavior of friction stir welded (FSWed) 7075-T6 aluminum alloy panel was investigated under biaxial loading. The biaxial fatigue tests were carried out on three kinds of cruciform samples, including base material (BM) cruciform sample and FSWed cruciform sample with crack perpendicular or parallel to the weld. Scanning electron microscope (SEM) fractography was conducted to identify and relate fracture surface features to governing fatigue damage mechanisms. Finite element method combined with stress intensity factor (SIF) analysis was used to simulate the biaxial fatigue propagation. In a comparison of the crack path in BM and FSWed cruciform samples, experimental and numerical results showed that residual stress can change the nominal biaxiality ratio, leading to crack path changes in FSWed cruciform sample with crack parallel to the weld, and the curved fatigue crack front formed on the fracture surface due to the non-uniform distribution of the residual stress through the thickness. The fatigue damage mechanisms are different depending upon the biaxiality ratio as well as the weld direction.

Ex-situ observation of the short crack initiation and propagation behaviour of nickel-base wrought alloy Inconel 718 for critical rotating components under fatigue conditions at elevated temperatures

In this paper, the initiation and propagation behaviour of short fatigue cracks in nickel-base alloy Inconel 718 is studied extensively in the fatigue loading regime by ex-situ scanning electron microscopy on component-near notched specimens in the temperature range between 400°C and 600°C. To investigate the influence of different surface treatments, both specimens with polished and shot-peened surfaces were tested. For polished specimens, most fatigue cracks initiated at oxidised non-metallic inclusions, whereas for shot-peened specimens, the process-induced surface roughness also served as crack starters. It was found, that the observed scatter in lifetime for repetitive tests is mainly caused within the short crack fatigue regime below 50μm, while cracks larger than 100μm showed similar growth characteristics.

Microstructural insights into fatigue short crack propagation resistance and rate fluctuation in a Ni-based superalloy manufactured by laser powder bed fusion

The microstructural sensitivity of fatigue short crack path and its propagation rate in a Ni-based superalloy GH4169 manufactured by laser powder bed fusion (LPBF) was investigated at room temperature. In-situ digital image correlation (DIC) observation and post-mortem microstructural analysis around the crack path were performed. The results show that the intragranular cracks developed in the shear cracking mode are closely aligned along the activated slip bands in the γ-matrix grains with the crystallographic characteristics of parallel to the γ-{111} slip planes. Multiple slip was also activated, causing the crack retardation or deflection. Low-angle grain boundaries and subgrain boundaries were shown to cause deflections of intragranular cracking, while high-angle grain boundaries significantly arrested the short crack propagation. Moreover, the resistance of grain boundaries to short cracking was assessed using combined metrics including the crystallographic and microstructural parameters of twist angle, the Schmid factor and the geometrical compatibility factor. These site-specific microstructural analyses around the crack path provide insights into the microstructural origins of resistance to the short crack propagation as well as an interpretation of the observed significant fluctuations in the crack propagation rate.

Fatigue behaviors of ultrasonic surface rolling processed AISI 1045: The role of residual stress and gradient microstructure

In the study, AISI 1045 steel were treated by ultrasonic surface rolling processing (USRP) with different parameters in terms of coverage rate. The gradient structures characterized with refined polished surface, the sub-surface nano-lamellar microstructure with a maximum compressive residual stress of 453.4 MPa was obtained, which shall be responsible to the superior fatigue properties to the pristine. Furthermore, the comparative investigation of fatigue behavior demonstrates that the surface roughness has the pronounce effects on the resistance to crack initiation, though the excessive USRP with the surface roughing may result in the premature crack growth; in contrast to the gradient microstructure, the compressive residual stress may delay effectively the incubation and increase the growth resistance of the physically short crack. Besides, the benefit of gradient microstructure is relatively limited in the resistance of fatigue short crack propagation.

Microstructure relevant fatigue short crack propagation behavior of Al0.3CoCrFeNi high entropy alloy: in-situ SEM study

The microstructure effects on fatigue short crack propagation behavior of Al0.3CoCrFeNi high entropy alloys (HEAs) were studied by in-situ fatigue testing under scanning electron microscope (SEM). The experimental results indicated that fine grain (FG) specimens had better fatigue crack propagation resistance and higher fatigue life compared with coarse-grain (CG) specimens. Fatigue short crack propagation followed transgranular mode, associated with octahedral slip. The fatigue small crack growth is primarily microstructurally sensitive, showing evident fluctuations related to the blocking effects of grain boundaries and twin boundaries. Furthermore, a modified fatigue crack growth model has been proposed, which can successfully evaluate the crack growth rates of HEAs with different grain microstructures under different fatigue stresses.

The behavior of anisotropic fatigue short crack initiation and propagation for a directionally solidified superalloy CM247LC at room temperature

AbstractThe effects of mechanical and microstructural anisotropy on short fatigue crack initiation and propagation behaviors of a directionally solidified superalloy have been studied. An unusual result was found where the fatigue lives of specimens with grains longitudinally aligned along the loading direction fail at lower lifetimes than specimens with transversely loaded grains when the applied stress is close to the yield stress. This is mainly attributed to the lower Young's modulus of the longitudinal specimen, which induces more local plastic strain (at stress concentration features) leading to earlier crack initiation and faster crack propagation under the applied test stress.

Review of Fatigue Crack Initiation Mechanisms Development and Monitoring in the Very High Cycle Fatigue Regime

Abstract Fatigue devices working at high frequency (20 kHz) allow now to explore the fatigue domain with a total number of cycles much higher than 107 cycles in reasonable times. In that case, lifetime belongs to the very high cycle fatigue (VHCF) domain. As for low and high cycle fatigue (LCF and HCF), the fracture begins by microstructural damage because of microplasticity, before leading to the initiation stage (stage I), and then the short and long crack propagation stages (stage II). It is now admitted that in VHCF the initiation stage is higher than 90 % of the total life. The main difference with LCF and HCF is the crack initiation location. For materials without internal defects (type I), the initiation is always on the specimen surface, whereas for materials with internal defects (inclusions, porosities, etc.) named type II, the microstructure appears in subsurface on defects leading to a typical “fish eye” on fractographies. If the crack initiation mechanisms on surface are well accepted to be related to dislocations gliding in well-oriented grains, the mechanisms in subsurface are not very clear and many hypotheses on the fish-eye development are suggested by different authors. In the fish-eye center, it appears a fine granular area more or less large, the origin of which is debated. In the first part, this article proposes a review on these crack initiation mechanisms (surface and subsurface). Microplasticity produces a temperature increase in fatigue tests. It has been demonstrated that the temperature recording during tests is a mean to determine the number of cycles corresponding to crack initiation and crack propagation. In the second part, through two examples on Armco iron (surface initiation) and a low alloy steel (subsurface crack initiation), the method to determine the number of cycles during the initiation and propagation stages is exposed.

Microstructural effects on short fatigue crack propagation in cast Al-Si alloys

The role of microstructure on the short fatigue crack behaviour of cast Al-Si alloy under high cycle loading conditions is investigated by tracking the progress of cracks through fine, medium and coarse microstructured samples. Generally, in the early stage of crack growth, short cracks mainly grow transgranularly, with cracks growth close to low index crystallographic planes (mainly {100}) in some grains and frequently inhibited at grain boundaries. In the late stage, the crack growth mode gradually shifts from crystallographic stage-I to non-crystallographic stage-II. The short cracks grow faster and fluctuate significantly according to local microstructure. Our results show that finer microstructures offer greater crack nucleation and propagation resistance.

Comparative study of the effects of conventional shot peening and ultrasonic shot peening on very high cycle fatigue properties of GH4169 superalloy

This study investigates the effects of two different shot peening techniques, conventional shot peening (CSP) and ultrasonic shot peening (USP), on the very high cycle fatigue (VHCF) properties of the GH4169 superalloy. The study evaluates and compares surface roughness, X-ray diffraction patterns, microhardness, and residual stress in specimens treated with CSP and USP. The VHCF tests reveal that both CSP and USP treatments improve the VHCF properties of the GH4169 superalloy. However, while the USP-treated specimens have deeper work hardening and compress residual stress layers, their VHCF lives are significantly shorter than those of the CSP-treated specimens. Additionally, the study finds that the stress triaxiality, which inhibits dislocations at the crack tip, is higher closer to the center of the specimen. The transmission electron microscopy (TEM) results further confirm that the reduced dislocation density and increased stress concentration in the plastic zone of the high stress triaxiality region promote fatigue short crack propagation and reduce the fatigue properties of the material.

Computational study of the geometrical influence of grain topography on short crack propagation in AA7XXX series alloys

Intergranular Environmentally-Assisted Cracking (EAC) has recently been reported to be an issue of concern in new-generation 7000 series aluminium alloys, such as AA7085, when exposed to humid air. The cracking process occurs in a highly brittle manner almost exclusively along grain boundaries (GB's) and has been attributed to hydrogen embrittlement, probably by GB decohesion within the stress field at the crack tip. Currently, how the highly heterogeneous grain structures found in these partially recrystallized materials impact the growth behaviour of microstructurally short cracks is poorly understood. In particular, there is expected to be a high sensitivity to the grain structure in the transition from initiation to sustained propagation, where the local mechanical driving force is very sensitive to the crack path. Volume Elements, VE's, with synthetic grain structures have been generated from real microstructure and texture data, so that the effects of important grain structure variables can be explored in crystal-plasticity simulations, to understand the extent to which typical grain-structural features affect the driving force for short-crack growth. Specifically, by considering the effect of different uncrystallised grain aspect ratios and embedding recrystallised grains in the model, the strain energy release rate has been calculated as a function of crack path. This has revealed large reductions and fluctuations in the driving force for short cracks in relation to the local grain structure encountered by the crack tip, which have been estimated by the model.

Fatigue Crack Growth in a Monocrystal and Its Similarity to Short-Crack Propagation in a Polycrystal of Nickel

Short fatigue cracks in polycrystalline materials are very important from both practical and basic aspects, yet they are very difficult to observe. Therefore, it is suggested to emulate some properties of short cracks with long fatigue cracks in monocrystals. Indeed, such experiments in pure nickel crystals prove that the three peculiar properties of short fatigue cracks in polycrystalline metals are observed in long cracks in monocrystals, i.e., a lower threshold of the stress intensity factor (ΔKI)th, a higher crack propagation rate at low ΔKI regimes, and the fact that different cracks exhibit different growth behaviors. The fatigue experiments in monocrystals reveal interesting details of the slip activity at the front of fatigue cracks, including a selection rule for the active slip systems above and below the crack, the slip behavior under conditions of steep strain gradients, and the activation of a new slip system.