RF Power Research Articles

Comparative efficiency analysis of RF power amplifiers with fixed bias and envelope tracking bias

Comparative efficiency analysis of RF power amplifiers with fixed bias and envelope tracking bias

Ultra-wideband GaN RF power amplifier based on low-pass ladder matching network

Ultra-wideband GaN RF power amplifier based on low-pass ladder matching network

Absorber-Free Mode-Locking of a Hybrid Integrated Diode Laser at Sub-GHz Repetition Rate

We demonstrate absorber-free passive and hybrid mode-locking at sub-GHz repetition rates, using a hybrid integrated extended cavity diode laser operating near 1550 nm. The laser is based on InP as a gain medium and a Si3N4 waveguide feedback circuit. Absorber-free Fourier domain mode-locking with ≈15 comb lines at around 0.2 mW total power is achieved with repetition rates around 500 MHz, using three highly frequency-selective micro-ring resonators that extend the on-chip cavity length to 0.6 m. To stabilize the repetition rate, hybrid mode-locking is demonstrated by weak RF modulation of the diode current. The RF injection reduces the Lorentzian linewidth component from 8.9 kHz to a detection-limited value of around 300 mHz. To measure the locking range of the repetition rate, the injected RF frequency is tuned with regard to the passive mode-locking frequency and the injected RF power is varied. The locking range increases approximately as a square-root function of the injected RF power. At 1 mW injection, a wide locking range of about 80 MHz is obtained. We also observe the laser maintaining stable mode-locking when the DC diode pump current is increased from 40 mA to 190 mA, provided that the cavity length is maintained constant with thermo-refractive tuning.

First high-power helicon results from DIII-D

Abstract More than 0.6 MW of rf power at 476 MHz has been coupled to DIII-D plasmas by launching helicon (whistler) waves with a traveling-wave antenna (comb-line) in the fast-wave polarization (Van Compernolle et al 2021 Nucl. Fusion 61 116034) which resulted in the observation of electron heating of the core plasma with single-pass absorption based on ray-tracing in L-mode discharges. The coupling performance of the 1.5 m wide 30-element comb-line traveling-wave antenna has been consistent with expectations based on the 2015–2016 experiments on DIII-D with a low-power 12-element prototype (Pinsker et al 2018 Nucl. Fusion 58 106007). The conditioning process that was necessary to carry out high-power experiments is discussed; rf-specific impurities have not been observed. Parametric decay instabilities have been observed and are being investigated as a potential edge absorption mechanism (Porkolab et al 2023 AIP Conf. Proc. 2984 070004).

Impact of Ar plasma bombardment on the composition and surface roughness of GaAs wafer

The surface property of GaAs has an important impact on device performance, so how to improve the surface quality in reactive ion etching process is one of the key issues. In this paper, the composition and roughness changes of GaAs surface subjected to Ar plasma bombardment were investigated. It was found that the relative contents of Ga2O3 and As2O3 of the surface decreased with the increase of RF power, and the distribution depths of the compositions were different. In addition, dielectric constant increased with the increase of RF power. It was found that the surface roughness can be reduced after the plasma bombardment. Furthermore, the surface roughness and Ga/As component ratio followed a certain trend with the RF power. When the RF power was lower than 150 W, the surface roughness and Ga/As component ratio had the same trend, and when the RF power was higher than 150 W, they had the opposite trend. These results are helpful for the improvement of GaAs-based wafer-bonding strength and the performance of optoelectronic structures.

Bulk acoustic wave—Solidly mounted resonator with a-SiOCN:H as low-Z material

Bulk acoustic wave (BAW) filters have been proven to be of high demand in today's low power RF front-ends for mobile communication devices. Within the launch of 5G applications worldwide, especially in the region of new radio (nr-1) up to 6 GHz, defined frequency bands require filters of wide bandwidths, while simultaneously featuring steep edges and high out-of-band rejection. Due to the coexistence with 4G LTE (long term evolution) wireless standards as well as advanced data transfer concepts such as carrier aggregation, the increasing complexity of antenna systems forces the implementation of highly selective acoustic filters. In contrast to the widely used surface acoustic wave (SAW) technology, BAW filters appear with superior performance for frequencies above 1 GHz. This work describes the fabrication of a BAW-solidly mounted resonator (BAW-SMR) with a tailored material system of a-SiOCN:H as a low impedance (low-Z) material integrated within its acoustic Bragg mirror. A direct comparison to the widely used low-Z material of SiO2 with an acoustic impedance of around 13 MRayl is demonstrated by two equal resonator stacks by replacing only the uppermost low-Z thin film of the acoustic reflector. A single-mask design was chosen with platinum as a bottom electrode to ensure the most equal growth conditions for the piezoelectric aluminum nitride (AlN) layers on both reflectors’ surfaces featuring either the tailored a-SiOCN:H or standard SiO2. The a-SiOCN:H thin films were deposited by plasma-enhanced chemical vapor deposition and the according acoustic impedance was priorly depicted to 7.1 MRayl, which could be exploited to achieve an increase in the effective coupling coefficient beyond 7% as well as a resonator bandwidth of more than 60 MHz.

Index Modulation-Based Information Harvesting for Far-Field RF Power Transfer

Index Modulation-Based Information Harvesting for Far-Field RF Power Transfer

On forced RF generation of CW magnetrons for accelerators

CW magnetrons, initially developed for industrial RF heaters, were suggested to power RF cavities of superconducting accelerators due to their higher efficiency and lower cost than traditionally used klystrons, IOTs or solid-state amplifiers. RF amplifiers driven by a master oscillator serve as coherent RF sources. CW magnetrons are regenerative RF generators with a huge regenerative gain. This causes regenerative instability with a quite large noise when a magnetron operates with the anode voltage above the threshold of self-excitation. Traditionally, an injection locking by a small signal is used for stabilization of magnetrons. In this case CW magnetrons with the injection-locked oscillations generate a high level of noise. This may preclude use of standard CW magnetrons in this operating mode in the Superconducting RF (SRF) accelerators. In this article we described a method developed for forced RF generation of CW magnetrons when the magnetron startup is provided by the injected forcing signal and the regenerative noise is suppressed. The method is most suitable for powering high Q-factor cavities.

Operating Characteristics of a Wave-Driven Plasma Thruster for Cutting-Edge Low Earth Orbit Constellations

This paper outlines the development phases of a wave-driven Helicon Plasma Thruster for cutting-edge Low Earth Orbit (LEO) constellations. The two-stage ambipolar electric propulsion (EP) system combines the efficient ionization of an ultra-compact helicon reactor with plasma acceleration based on an ambipolar electric field provided by a magnetic nozzle. This paper reveals maturation challenges associated with an emerging EP system in the hundreds-watt class, followed by outlook strategies. A 3 cm diameter helicon reactor was operated using argon gas under a time-modulated RF power envelope ranging from 250 W to 500 W with a fixed magnetic field strength of 400 G. Magnetically enhanced inductively coupled plasma reactor characteristics based on half-wavelength right helical and Nagoya Type III antennas under capacitive (E-mode), inductive (W-mode), and wave coupling (W-mode) were systematically investigated based on Optical Emission Spectroscopy. The operation characteristics of a wave-heated reactor based on helicon configuration were investigated as a function of different operating parameters. This work demonstrates the ability of two-stage HPT using a compact helicon reactor and a cusped magnetic field to outperform today’s LEO spacecraft propulsion.

Sensitivity Enhancement of Ultra-Wideline NMR by Progressive Saturation of the Proton Reservoir Under Magic-Angle Spinning.

Solid-state NMR of low-γ nuclides is often characterized by low sensitivity and by significant spectral broadenings induced by the quadrupolar and the chemical-shift anisotropy interactions. Herein, we introduce an indirect acquisition method, termed PROgressive Saturation of the Proton Reservoir Under Spinning (PROSPRUS), which could facilitate the acquisition of ultra-wideline NMR spectra under magic-angle spinning (MAS), in systems with a sufficiently long dipolar relaxation time, T1D. PROSPRUS NMR relies on the generation of so-called second-order dipolar order among abundant protons undergoing MAS, and on the subsequent depletion of this dipolar order by a series of looped cross-polarization events, transferring the proton order into polarization of the low-γ I-nuclei as a function of the latter's offsets. While the spin dynamics of the ensuing experiment is complex, particularly when dealing with narrow I spectral lines, it is shown that PROSPRUS can lead to faithful lineshapes for ultra-wideline spin-1/2 and spin-1 species, providing high sensitivity with extremely low RF power requirements. It is also shown that the ensuing 1H-detected PROSPRUS experiments can efficiently characterize I-spin lineshapes in excess of 1 MHz without having to retune electronics, while providing improvements in sensitivity per unit time over current broadband direct-detection methods by up to a factor of four.

S-band high-gradient low β single-periodic magnetically coupled standing-wave accelerating structure for a proton therapy linac

S-band high-gradient accelerating structures were proposed to accelerate protons from 30 to 230 MeV for a compact proton therapy linac in Institute of Modern Physics. A backward traveling wave structure and a single-periodic magnetically coupled standing wave structure were designed, and differences between these two structures were analyzed to select a more suitable one for the proton therapy linac. In this paper, a novel single-periodic magnetically coupled standing-wave accelerating structure was studied, with an optimized nose cone that related to a smaller peak surface electric field and higher shunt impedance, with the reduced number of coupling holes and mechanical von Mises stress thus making it possible for higher duty factor and longer rf pulse operation, also with larger coupling holes and improved cell-to-cell coupling thus making this structure suitable for operating in π mode. An 11-cell high-power prototype for β=0.26 particles was developed with an active length of 143 mm. This prototype cavity is supposed to operate at an accelerating gradient of 30 MV/m with 0.1% duty factor, corresponding to a maximum surface electric field of 105 MV/m and a peak rf power of 3.43 MW. Cavity design, optimization, manufacture, rf measurement, and high-power test will be discussed in this paper. Published by the American Physical Society 2024

Evaluation of the RF depositions at 3T in routine clinical scans with respect to the SAR safety to improve efficiency of MRI utilization.

This study explores the potential for improving of 3T MRI utilization by assessing and tailoring RF exposure in routine clinical scans while complying to standard safety limit. Using two generic human body models, we evaluated pbSAR10g values at four landmark positions (knee, pelvis, thoracic spine, head) at different wbSAR levels. Specifically, weanalyzed local SAR10g in different operating modes and computed the maximum safety wbSAR, ensuring compliance with IEC limits. In normal operating mode, the RF power deposition reached wbSAR limit before the pbSAR10g limit. In the first level controlled operating mode, pbSAR10g limit is reached before the wbSAR limit in the knee, thoracic spine scanning scenarios, while the wbSAR limit is reached first in the pelvis scanning scenarios, making it the most potential-releasing (up to 33.33 %) scanning scenario. For head exposure, the head SAR10g limit is reached before the wbSAR limit, highlighting the necessity for strict SAR control. Moreover, we calculated the minimum allowable TR for common imaging sequences for reference. Different RF exposure setups are necessary to meet safety standards in various scenarios. By implementing careful RF exposure setups in routine clinical scans, the high potential capacity of 3T MRI can be fully released.

Enhancing Security of Telemedicine Data: A Multi-Scroll Chaotic System for ECG Signal Encryption and RF Transmission.

Protecting sensitive patient data, such as electrocardiogram (ECG) signals, during RF wireless transmission is essential due to the increasing demand for secure telemedicine communications. This paper presents an innovative chaotic-based encryption system designed to enhance the security and integrity of telemedicine data transmission. The proposed system utilizes a multi-scroll chaotic system for ECG signal encryption based on master-slave synchronization. The ECG signal is encrypted by a master system and securely transmitted to a remote location, where it is decrypted by a slave system using an extended state observer. Synchronization between the master and slave is achieved through the Lyapunov criteria, which ensures system stability. The system also supports Orthogonal Frequency Division Multiplexing (OFDM) and adaptive n-quadrature amplitude modulation (n-QAM) schemes to optimize signal discretization. Experimental validations with a custom transceiver scheme confirmed the system's effectiveness in preventing channel overlap during 2.5 GHz transmissions. Additionally, a commercial RF Power Amplifier (RF-PA) for LTE applications and a development board were integrated to monitor transmission quality. The proposed encryption system ensures robust and efficient RF transmission of ECG data, addressing critical challenges in the wireless communication of sensitive medical information. This approach demonstrates the potential for broader applications in modern telemedicine environments, providing a reliable and efficient solution for the secure transmission of healthcare data.

Investigating the mechanism of enhancing interfacial adhesion of SiOx films on GaAs substrates through process optimization

In the manufacturing of GaAs-based quantum well (QW) lasers, the adhesion between the Silicon dioxide (SiOx) film layer and the Gallium arsenide (GaAs) substrate is crucial for the performance and durability of semiconductor devices. This study focused on depositing SiOx films on GaAs substrates using plasma-enhanced chemical vapor deposition (PECVD). The research aimed to investigate the impact of different coating processes on the deposition rate, properties, and composition of the coatings. The interfacial adhesion of various samples was assessed using nano-scratch tests. The results revealed that samples with lower SiH4 gas flow and RF power, or higher process pressure exhibited stronger adhesion strength. It's further observed that optimizing the process parameters reduced residual stresses in the film, thereby enhancing the GaAs-SiOx interfacial bonding. This work has the potential to significantly reduce the possibility of QW lasers malfunctions, improve the reliability of semiconductor devices and provide valuable insights for future studies on enhancing film-substrate adhesion.

Nonlinear response of very high frequency contour mode resonators

We explore the source of nonlinearities in Aluminum Nitride (AlN) Contour Mode Resonators (CMRs) operating in the Very High Frequency (VHF) range. We demonstrate that the red-shift of the resonance frequency found in VHF CMRs when the input RF power increases is due to nonlinear stiffness appearing from self-heating, and variable damping due to geometric nonlinearities. Moreover, we find a linear relationship between the variable damping coefficient and the resonator quality factor (Q). Such nonlinear mechanisms are modeled using a spring-mass-damper physical system and, in the electrical domain, a modified Butterworth-Van Dyke (MBVD) circuit where the nonlinear stiffness and variable damping are captured by a charge-dependent motional capacitor and a charge-dependent motional resistor, respectively. Detailed guidelines are provided to accurately analyze nonlinear CMRs using full-wave numerical simulations based on a finite-element method. Such simulations allow us to isolate the influence of each independent nonlinear mechanism and establish a relation between variable damping and geometric nonlinearities. Circuit and full-wave numerical simulations are in good agreement with measured data from fabricated 225 MHz CMRs exhibiting different Q. Finally, we exploit nonlinearities in high-Q CMRs to generate frequency combs at the MHz range opening the door to new exciting applications in telecommunication and sensing.

UNCERTAINTY EVALUATION USING LAW OF PROPAGATION AND MONTE CARLO SIMULATION METHODS WITH THE AUTORFPOWER MEASUREMENT SOFTWARE

RF power measurement is essential in RF and microwave metrology. For reliable and accurate power measurement, automatic measurement is preferred. A software application in C#, named AutoRFPower, was developed for automatic RF power measurement and uncertainty calculations at this study. According to the GUM document, this application is enhanced for uncertainty calculations by utilizing the Law of Propagation method and the Monte Carlo Simulation method. Trial measurements were performed at different RF power levels and frequencies between 50 MHz and 18 GHz using the AutoRFPower software. Law of Propagation and Monte Carlo Simulation uncertainty calculations were carried out by AutoRFPower based on the trial measurements and by the Oracle Crystal Ball simulation application. All measurements and their uncertainty calculations were compared with each other, and this study validated the uncertainty calculation of AutoRFPower. In addition, it was observed that in the Monte Carlo Simulation, uncertainty calculation results were non-symmetrical normal distribution, contrary to the assumption of symmetrical normal distribution according to the Low of Propagation method. Moreover, it has been observed that the statistical distribution of uncertainty changes depending on the dominant component of the parameters in the model function used for the uncertainty calculation with the Monte Carlo Simulation method.

A Unified Neural Network-Based Approach to Nonlinear Modeling and Digital Predistortion of RF Power Amplifier

A Unified Neural Network-Based Approach to Nonlinear Modeling and Digital Predistortion of RF Power Amplifier

Monitoring of the Cancer Treatment Process by Temperature Measurements

The usage of temperature measurements in the Magic Light anti-cancer therapy has been investigated in clinical trials for the treatment of Triple Negative Breast Cancer (Invasive Ductal Carcinoma Stage III). Irradiation by RF waves, from the Magic Light device, can increase or decrease the patient’s body temperature during one treatment session. It allows for the visualization of the cancer treatment process as well as to monitor its progress.Treatment of Invasive Ductal Carcinoma (IDC) Stage III, using the Magic Light anti-cancer therapy, was completed and described. The best treatment effect was observed at a frequency of 430 MHz and, applied in turn, at modulation frequencies of 4 kHz, 7 kHz, 10 kHz and 21 kHz and with RF power densities less than 12 mW/cm2 at a distance of 1 m from the patient.The process of cancer treatment using the Magic Light anti-cancer therapy was monitored by measuring the patient’s body temperature both before and after each treatment session. A new medical effect was disclosed, which allows the observance of efficiency and progress in the cancer treatment, as well as detecting the presence of cancer cells at the early stages of disease.In this trial, it was discovered that if cancer is present in the human body, the body temperature after the Magic Light treatment session will always be higher than before this treatment session began. However, if during 5-6 treatment sessions in turn, the body temperature after the treatment session, is lower than it was initially, it means that the cancer has been cured completely.Temperature measurements using the Magic Light device, may also be used as an oncology test.

Uncertainty Calculation as a Service: Integrating Cloud-Based Microservices for Enhanced Calibration and DCC Generation.

The calibration industry is renowned for its diverse and sophisticated equipment and complex processes, which necessitate innovative solutions to keep pace with rapidly advancing technology. This paper introduces an enhancement to an existing microservice-based cloud architecture, aimed at effectively managing the inherent complexity within this field. The enhanced architecture seamlessly integrates various equipment types and communication technologies, aligning diverse stakeholder expectations into a unified system that ensures efficient and accurate calibration processes. It highlights the integration of microservices to facilitate various methods of uncertainty calculation and the generation of digital calibration certificates (DCCs). A case study on RF power measurement illustrates the practical application and benefits of the enhanced architecture. Although initially focused on RF power measurement, the flexible architecture allows for future expansions to accommodate new standards and measurement techniques. The enhanced system offers a comprehensive approach to managing data flow from calibration equipment to the final generation of DCCs, utilizing cloud-based services for efficient data processing. As a future direction, this extension sets the groundwork for broader applicability across multiple measurement types, ensuring readiness for upcoming advancements in metrology.

Green Wearable Sensors and Antennas for Bio-Medicine, Green Internet of Things, Energy Harvesting, and Communication Systems.

This paper presents innovations in green electronic and computing technologies. The importance and the status of the main subjects in green electronic and computing technologies are presented in this paper. In the last semicentennial, the planet suffered from rapid changes in climate. The planet is suffering from increasingly wild storms, hurricanes, typhoons, hard droughts, increases in seawater height, floods, seawater acidification, decreases in groundwater reserves, and increases in global temperatures. These climate changes may be irreversible if companies, organizations, governments, and individuals do not act daily and rapidly to save the planet. Unfortunately, the continuous growth in the number of computing devices, cellular devices, smartphones, and other smart devices over the last fifty years has resulted in a rapid increase in climate change. It is severely crucial to design energy-efficient "green" technologies and devices. Toxic waste from computing and cellular devices is rapidly filling up landfills and increasing air and water pollution. This electronic waste contains hazardous and toxic materials that pollute the environment and affect our health. Green computing and electronic engineering are employed to address this climate disaster. The development of green materials, green energy, waste, and recycling are the major objectives in innovation and research in green computing and electronics technologies. Energy-harvesting technologies can be used to produce and store green energy. Wearable active sensors and metamaterial antennas with circular split ring resonators (CSSRs) containing energy-harvesting units are presented in this paper. The measured bandwidth of the matched sensor is around 65% for VSWR, which is better than 3:1. The sensor gain is 14.1 dB at 2.62 GHz. A wideband 0.4 GHz to 6.4 GHz slot antenna with an RF energy-harvesting unit is presented in this paper. The Skyworks Schottky diode, SMS-7630, was used as the rectifier diode in the harvesting unit. If we transmit 20 dBm of RF power from a transmitting antenna that is located 0.2 m from the harvesting slot antenna at 2.4 GHz, the output voltage at the output port of the harvesting unit will be around 1 V. The power conversion efficiency of the metamaterial antenna dipole with metallic strips is around 75%. Wearable sensors with energy-harvesting units provide efficient, low-cost healthcare services that contribute to a green environment and minimize energy consumption. The measurement process and setups of wearable sensors are presented in this paper.