Output Power Research Articles

Coupled terahertz quantum cascade wire lasers

We present mutual optical coupling in terahertz (THz) quantum cascade wire laser arrays that are flip-chip bonded to a dielectric substrate. The mounting substrate is patterned for individual electrical contacting of each wire laser of the array. The resulting sandwich-like structure supports wire laser modes with a significant part propagating outside the cavity and mediates the long range coupling. The evanescent field part of the modes couples to the adjoining ridge, which, in turn, leads to mutual optical injection-locking between them. We demonstrate this effect for both geometrically similar and dissimilar wire lasers when biased in pulsed operation with temporally overlapping bias pulses. Finite element simulations confirm our measurement results. By applying time-shifted bias pulses to individual array elements, a controllable optical injection seeding of the wire cavity is achieved. We observe intensity modification of the laser modes with changing bias pulse overlap as a result of the injection locking. By choosing both the physical spacing of the laser ridges and the intensity of the seeding laser correctly, the relative intensities of the favored lasing modes are enhanced up to 95 percent. Understanding the coupling in THz wire laser arrays is important for future device improvements in terms of higher continuous-wave operating temperatures through better thermal dissipation, and higher output power and an improved far field due to controlled coupling of their modes.

All-solid-state continuous-wave mode-locked Er:Lu2O3 laser at 3 µm

In this paper, we demonstrated stable continuous-wave passively mode-locked operation of an Er:Lu2O3 laser at 3 µm, utilizing a semiconductor saturable absorber mirror (SESAM). By operating the laser in a dry nitrogen environment and utilizing a thermoelectric cooler (TEC) temperature control device to mitigate the thermal effects of Er:Lu2O3 and enhance laser stability, we further compensated for group delay dispersion within the laser cavity through chirped mirrors, an shortest pulse duration of 12.0 ps at a average output power of 150 mW was achieved, which occurred at a center wavelength of 2844 nm, and a pulse repetition rate of 83.5 MHz. Additionally, we achieved a maximum continuous-wave mode-locked output power of 213 mW at an absorbed pump power of 8.3 W, equivalent to a pulse energy of 1.3 nJ. The RF spectrum analysis of the pulse train indicated a high SNR of nearly 70 dB, signifying excellent stability. To the best of our knowledge, This is the first report on the realization of an ultrashort pulse width mode-locked Er:Lu2O3 laser in the mid-infrared band.

Nanostructured LNTO saturable absorber for generating multi-wavelength laser in Q-switched EDFL

In this paper, we propose a new and efficient ferroelectric nanostructure metal oxide lithium niobate [(Li1.075Nb0.625Ti0.45O3), (LNTO)] solid film as a saturable absorber (SA) for modulating passive Q-switched erbium-doped fiber laser (EDFL). The SA is fabricated as a nanocomposite solid film by the drop-casting process in which the LNTO is planted within polyvinylidene fluoride-trifluoroethylene [P(VDF-TrFE)] as host copolymer. The optical and physical characteristics of the solid film are experimentally established. The SA is incorporated within the cavity of EDFL to examine its capability for producing multi-wavelength laser. The experimental results proved that a multi-wavelength laser is produced, where stable four lines with central wavelengths at 1529.5, 1530.5, 1531.5, and 1532 nm are observed on the laser spectrum at 157 mW pumped power. Furthermore, at maximum available pumped power (157 mW), laser pulses are running with a rate of 178 kHz and pulse width of 2.64 μs. The output power of 3.7 mW is attained at pumped power of 157 mW. The result proved that the LNTO-SA could be a potential candidate for generating multi-wavelength passive Q-switched fiber laser pulses.

Development and comprehensive analyses of a hybrid solar–geothermal driven polygeneration system: Thermodynamic, exergoeconomic, and emergoenvironmental aspects

The present research proposed an innovative polygeneration system that uses solar, geothermal, and natural gas energy to produce power, heat, steam, and freshwater. The system consists of a proton exchange membrane fuel cell, an organic Rankine cycle, and a multi-effect thermal desalination system. The study included thermodynamic, exergy, exergoeconomic, exergoenvironmental, emergy-based exergoeconomic, and emergy-based exergoenvironmental factors in its comprehensive evaluation of the system. Results underscored the financial aspect of the organic Rankine cycle and cogeneration system, incurring costs of 0.4518 $/s and 1.054 $/s respectively, while also highlighting the system's capability to produce 6 kg/s of freshwater. The environmental impact rates were quantified for the organic Rankine cycle and cogeneration system at 0.1417 and 0.4814 pts/s respectively, situating the system within its ecological context. Further, the study detailed the total efficiency and net power output of the organic Rankine cycle and cogeneration system, ranging between 32.45–33.51% and 43.25–45.83% for efficiency, and 56956–56322 kW and 50174–51898 kW for net power output r espectively, showcasing the system's operational capacity. A parametric analysis was also integral to the study, examining the impact of key parameters on the functionality of the proposed system, thereby providing a nuanced understanding of the system's performance under varying operational scenarios.

Effects of Sports Bras and Breast Volume on Pulmonary System and Respiratory Symptom Responses to Exercise in Healthy Females.

This study assessed the individual and combined effects of sports bras and breast volume on pulmonary system and respiratory symptom responses to exercise in recreationally-active females. Twenty-three healthy females (18-27 y; bra sizes 32B-36DDD) were divided into small and large breast volume groups (SBV and LBV, respectively) around median volume (324 ml; mean ± SD SBV: 284 ± 38 ml vs. LBV: 560 ± 97 ml; p < 0.001, g = 3.84). Participants completed three 5-minute bouts of constant-load cycle exercise at 30, 60, and 90% of their peak power output while wearing a high-support sports bra, low-support sports bralette, or their own (self-selected) sports bra in randomized order. Measurements included ventilation, breathing pattern, respiratory pressures, diaphragm electromyogram (EMGdi), and ratings of perceived exertion (RPE), breathlessness (intensity and unpleasantness) and chest tightness due to bra. Compared to low-support and personal sports bras, the high-support sports bra evoked stronger sensations of restricted breathing and chest tightness ('slight' to 'moderate' restriction in n = 7 [30%] vs. n = 1 [4%] in low-support and personal bras; p = 0.014). There was, however, no evidence of greater concomitant inspiratory constraints, EMGdi, or inspiratory muscle pressure generation in either bra (all p > 0.05). Notably, LBV compared to SBV participants reported greater RPE (p = 0.037, ηp2 = 0.20), breathlessness intensity (p = 0.039, ηp2 = 0.20) and unpleasantness (p = 0.041; ηp2 = 0.19), which, in the setting of comparable pulmonary system responses to exercise, was likely driven by stronger perceived chest tightness and/or bra awareness in LBV participants. Despite evoking mild-to-moderately severe chest tightness due to bra during exercise - correctly fitted sports bras, whether low- or high-support, do not impose a physiological burden to the respiratory system and its response to mild-to-heavy intensity exercise in otherwise healthy females.

FOPDT model and CHR method based control of flywheel energy storage integrated microgrid

The main causes of frequency instability or oscillations in islanded microgrids are unstable load and varying power output from distributed generating units (DGUs). An important challenge for islanded microgrid systems powered by renewable energy is maintaining frequency stability. To address this issue, a proportional integral derivative (PID) controller is designed in this article. Firstly, islanded microgrid model is constructed by incorporating various DGUs and flywheel energy storage system (FESS). Further, considering first order transfer function of FESS and DGUs, a linearized transfer function is obtained. This transfer function is further approximated into first order plus time delay (FOPTD) form to design PID control strategy, which is efficient and easy to analyze. PID parameters are evaluated using the Chien-Hrones-Reswick (CHR) method for set point tracking and load disturbance rejection for 0% and 20% overshoot. The CHR method for load disturbance rejection for 20% overshoot emerges as the preferred choice over other discussed tuning methods. The effectiveness of the discussed method is demonstrated through frequency analysis and transient responses and also validated through real time simulations. Moreover, tabulated data presenting tuning parameters, time domain specifications and comparative frequency plots, support the validity of the proposed tuning method for PID control design of the presented islanded model.

Novel design of a staggered-trap/block flow field for use in serpentine proton exchange membrane fuel cells

Enhancing the transverse velocity to the catalyst layer and exploiting the over-rib flow are two common methods of improving proton exchange membrane fuel cells (PEMFCs). The block flow field configuration significantly affects the augmentation of the transverse velocity to the catalyst layer, whereas the trap configuration significantly increases the molar concentration of O2 at the cathode catalyst layer without a pressure drop penalty. In this study, four-channel PEMFC models with different configurations were used, including the baseline and staggered-trap, -block, and -trap/block channels. The novel flow field with a combination of trap/block configurations exhibits a higher power output than those of the other designs. Furthermore, the novel staggered-trap/block channel induces a higher over-rib flow velocity than that of the baseline channel, leading to more uniform O2 and temperature distributions within the PEMFC. The optimal trap/block design increases the maximum net cell power by 8.04 % at V = 0.5 V.

Isolator-free 60 W diamond Raman laser at 607 nm.

We report an intra-cavity frequency doubled diamond Raman laser operating at 607 nm. A z-fold cavity design was configured to prevent back reflections into the fiber amplifier, which avoided the use of isolators in the pump beam path. A maximum output power of 60 W was generated in two output beams at an optical conversion efficiency of 28% from the 1045 nm pump. A maximum single-beam output power of 40 W was obtained using a highly reflecting end mirror for the visible. Output power and single frequency stability are negatively impacted by an increasing role of stimulated Brillouin scattering at output powers above 10 W.

Research on the Performance of Thermoelectric Self-Powered Systems for Wireless Sensor Based on Industrial Waste Heat.

The issue of energy supply for wireless sensors is becoming increasingly severe with the advancement of the Fourth Industrial Revolution. Thus, this paper proposed a thermoelectric self-powered wireless sensor that can harvest industrial waste heat for self-powered operations. The results show that this self-powered wireless sensor can operate stably under the data transmission cycle of 39.38 s when the heat source temperature is 70 °C. Only 19.57% of electricity generated by a thermoelectric power generation system (TPGS) is available for use. Before this, the power consumption of this wireless sensor had been accurately measured, which is 326 mW in 0.08 s active mode and 5.45 μW in dormant mode. Then, the verified simulation model was established and used to investigate the generation performance of the TPGS under the Dirichlet, Neumann, and Robin boundary conditions. The minimum demand for a heat source is cleared for various data transmission cycles of wireless sensors. Low-temperature industrial waste heat is enough to drive the wireless sensor with a data transmission cycle of 30 s. Subsequently, the economic benefit of the thermoelectric self-powered system was also analyzed. The cost of one thermoelectric self-powered system is EUR 9.1, only 42% of the high-performance battery cost. Finally, the SEPIC converter model was established to conduct MPPT optimization for the TEG module and the output power can increase by up to approximately 47%. This thermoelectric self-powered wireless sensor can accelerate the process of achieving energy independence for wireless sensors and promote the Fourth Industrial Revolution.

Development of Steg with Concentrating System

Solar cells, also known as photovoltaic cells, convert light energy into electrical energy through the photovoltaic effect. Integrating a thermoelectric generator into a photovoltaic system enhances power output and efficiency by utilizing waste heat. Concentrators are employed to further improve solar panel efficiency. This study aims to develop a solar thermoelectric generator (STEG) with a concentrating system that includes a heat sink cooling system, thermoelectric generator, and concentrator. Three conditions will be tested to observe the power output of each solar module: PV standalone, STEG with a heat sink, and STEG with a heat sink and concentrator. The efficiency appears to improve from 9.21% for PV standalone to 10.11% for STEG with a heat sink and 10.23% for STEG with a concentrating system. The results of these studies aim to establish a benchmark for enhancing the efficiency of future STEG systems.

Pushing the tuning limits of femtosecond Yb-based solid-state lasers to 1 µm: a Yb:YVO4 laser tunable down to 1004 nm.

We have obtained what we believe to be the shortest fs tuning wavelength (1004 nm) from a Yb-based solid-state laser system. As the working horse, we have chosen Yb:YVO4 due to its blueshifted gain spectrum. While using a single 10 W 952 nm diode for pumping and a semiconductor saturable absorber mirror (SESAM) for mode-locking, we have achieved 266 fs long pulses with up to 1.24 W of output power around 1021 nm. Using an intracavity birefringent filter, the central wavelength of the fs pulses could be tuned smoothly between 1004-1038 nm and 1009-1061 nm while employing the E//a and E//c axis of the material, respectively. By using an additional hard aperture to increase the modulation depth, we have also attained 100 fs level pulses in the 1012.5-1019 nm range, which shows the suitability of the system in seeding cryogenic Yb:YLF-based amplifiers.

Generation of noise-like pulses in a linear-cavity Tm fiber mode-locked laser based on FMF saturable absorber

As a real saturable absorber (SA) based on the nonlinear multimode interference (NL-MMI) effect, the devices based on the few-mode fiber possess numerous exciting characteristics due to their all-fiber structure, straightforward manufacturing process. In this paper, by employing a SA with the SMF-FMF-SMF structure in a linear cavity, we demonstrate a stable mode-locked Tm-doped fiber laser. At the pump power of 1 W, a single noise-like pulse (NLP) with a pedestal pulse duration of 28 ps and coherent peak width of 0.77 ps is generated at a central wavelength of 1940 nm with a 3 dB bandwidth of 10.51 nm. The stable noise-like pulse can be sustained from the lasing pump threshold up to the maximum pump power of 2.2 W without experiencing pulse splitting. The experiment results in a peak average output power of 116 mW, along with a corresponding maximum pulse energy of 24.73 nJ at a repetition frequency of 4.69 MHz. The high stability of our fiber laser is confirmed by the signal-to-Noise Ratio (SNR) of 63 dB, and its enduring stability is additionally validated over an 8-hour period. The experimental findings suggest that the SMF-FMF-SMF structure has significant potential in the simple and robust all-fiber mode-locked lasers operating in the noise-like pulse regime.

Directional‐Thermal‐Conductive Phase Change Composites Enabling Efficient and Durable Water‐Electricity Co‐Generation Beyond Daytime

AbstractSolar‐driven water‐electricity co‐generation (WEC) emerges as a viable solution to address global freshwater and energy scarcity. Phase change materials (PCMs)‐based WEC systems have been proposed to solve intermittent solar radiation issues. Nevertheless, WEC performances decline significantly leading to limited operating durations in dark. The study proposes a new concept of directional‐thermal‐conductive PCMs to address above challenges. By precisely regulating hydrophilicity/hydrophobicity distribution of Cu substrates, the structural disorder of boron nitride‐based PCMs is effectively tuned to achieve directional thermal transport. These directional‐thermal‐conductive PCMs exhibit a high phase transition enthalpy of 250.4 J g−1 and a large thermal‐conductivity anisotropy index of 3.24, which improves heat exchange between PCMs and photothermal/thermoelectric, and minimizes transverse heat dissipation simultaneously. Consequently, the directional‐thermal‐conductive PCMs‐based WEC achieves evaporation rates of 2.51 kg m−2 h−1 with power outputs of 1759.7 mW m−2 at 1 sun, among the best performance reported in the state‐of‐the‐art studies. More impressively, its evaporation rate still reaches 0.93 kg m−2 h−1 with a superior power output of 411.0 mW m−2 and a prolonged operation time of 90 minutes in nighttime, significantly surpassing previously‐reported devices with nondirectional‐thermal‐conductive designs. Finally, an omniphobic PVDF membrane is demonstrated that can improve the anti‐fouling performance of WEC systems for prolonged lifespan.

Recent Advances in Wearable Textile-Based Triboelectric Nanogenerators.

We review recent results on textile triboelectric nanogenerators (T-TENGs), which function both as harvesters of mechanical energy and self-powered motion sensors. T-TENGs can be flexible, breathable, and lightweight. With a combination of traditional and novel manufacturing methods, including nanofibers, T-TENGs can deliver promising power output. We review the evolution of T-TENG device structures based on various textile material configurations and fabrication methods, along with demonstrations of self-powered systems. We also provide a detailed analysis of different textile materials and approaches used to enhance output. Additionally, we discuss integration capabilities with supercapacitors and potential applications across various fields such as health monitoring, human activity monitoring, human-machine interaction applications, etc. This review concludes by addressing the challenges and key research questions that remain for developing viable T-TENG technology.

Enhancing PV Panel Performance with Different Types of Phase Change Material (PCM): An Experimental Study

This study examined two solar panels with a high producing capacity of 250 W for performance enhancement utilizing several types of paraffin wax (RT57, RT61, and RT68) connected to the panel's rear surface. Two solar panels (one reference and one combined with PCM; PV-PCM) are used for outdoor tests. The current implementation is made with three types of PCM with a fixed thickness (3 cm) and with different inclination angles of 10°, 20°, 30°, and 40°. According to the results, the PV panels' tops had the maximum temperature spread, while their bottoms showed the lowest variation in temperature. At an inclination angle of 10◦, the temperature on the upper side of the plate is 18.8% higher than the lower side, 14.3%, and 12.2% for PCM1, PCM2, and PCM3, respectively. There is also an improved electrical power output of 16.8% for the PV-PCM panel with 3 cm PCM thickness over the reference panel (PV) with a tilt angle of 40◦. Relatedly, raising the inclination angle from 10◦ to 40◦ improves the Energy efficiency of PV-PCM with a thickness of 3 cm PCM by 10.4%. Finally, using 3 cm thick PCM improves the Energy efficiency of the PV-PCM panel by 17.4% compared to PV with an inclination angle of 30◦.

Effect of Piston Geometry on Performance Characteristics of VCR Engine with and without EGR when Fueled with Blends of Methyl Ester

The growing population and exhaustion of fossil fuels necessitate our search for new sources of energy. The study for this research encompasses an amalgamation of interest in alternative fuels, advanced engine technology such as variable compression ratio VCR, engine component modification, and a methodical approach to testing for assessing the effects on key performance of the engine. A 3.5 kW compression ignition (CI) engine was fueled with blends of behada, chicken fat, and turmeric oil methyl ester. Engine operating parameters, such as the compression ratio (CR), rate of exhaust gas recirculation (EGR), and piston top geometry, are optimized to maximize engine performance. CI engine was modified by changing the piston head (square and tangential groove top) for methyl ester diesel blend operations. In the study, diesel fuel is designated as B00 and methyl ester as B20. The influence of compression ratio (CR16 and CR18) with exhaust gas re-circulation (EGR 0% and EGR 10%) was evaluated. The key performance indicators: brake thermal efficiency (BTE), brake-specific energy consumption (BSEC), brake-specific fuel consumption (BSFC), air-to-fuel ratio (AFR), and exhaust gas temperature (EGT) are investigated. Results indicate that an increase in BTE accompanies an increase in load, suggesting enhanced thermal efficiency with increased power output. The consequence of VCR is also investigated, and it is determined that a higher CR results in a higher BTE due to an increase in compression pressure and temperature, thereby enhancing combustion. Due to the re-combustion of unburned hydrocarbons with the addition of EGR at a 10% rate, BTE increases further. Utilizing a piston geometry with tangential grooves and methyl ester blends also contributes to increased BTE. BSEC increases with increasing load, with an important rise observed when operating at maximum capacity. However,at CR 18, BSEC decreases as a result of enhanced combustion efficiency. EGR has different effects on BSEC depending on the geometry of the piston and the kind of fuel used. Enhanced air-fuel blending and re-combustion of unburned hydrocarbons reduce the BSEC of the engine. The tangential groove top piston operates with 10% EGR. Similar to BSEC, BSFC decreases with increasing CR and improves with the use of a piston with a tangential groove and 10% EGR operation. AFR decreases as the consumption of fuel increases to meet the power demand, and higher CR values result in a lower AFR. EGT rises with load, and CR18 has a lower EGT than CR16 as a result of a higher compressing temperature and pressure. 10% EGR operation reduces EGT by decreasing the concentration of oxygen in the combustible area.

Independent Pitch Adaptive Control of Large Wind Turbines Using State Feedback and Disturbance Accommodating Control

Wind turbines experience significant unbalanced loads during operation, exacerbated by external disturbances that challenge the stability of the pitch control system and affect output power. This paper proposes an independent pitch adaptive control strategy integrating state feedback and disturbance accommodating control (DAC). Initially, nonlinear wind turbine dynamics are globally linearized, and DAC is applied to mitigate the impact of wind disturbances dynamically. Subsequently, the entire range of wind speeds is segmented, and controllers are individually designed to optimize gain settings according to specific control objectives at each wind speed interval. Scheduling parameters such as collective pitch angle and tower fore-aft displacement are identified and trained using Radial Basis Function Neural Networks (RBFNN). Finally, based on the output gain values determined by RBFNN, the full-state feedback controller group is adaptively adjusted, and the optimal controller is selected for the final output. Simulations conducted on the NREL 5MW reference wind turbine model using FAST and Simulink demonstrate that compared to the ROSCO controller, the proposed strategy ensures smoother output power and effectively reduces blade and tower loads, thereby extending the turbine’s operational lifespan.

Improved performance of thermophotovoltaic energy conversion with Tamm plasmon emitters enabled by back gapped reflectors

A thermophotovoltaic (TPV) system that can convert thermal radiation from terrestrial heat sources into electricity, plays an important role in energy utilization, waste heat recovery and so on. In order to enhance the conversion efficiency of a TPV system having a narrow-band thermal emitter, we propose to add a back gapped reflector (BGR) to recover more out-of band (OOB) photons. We first design a Tamm plasmon thermal emitter to yield a narrow-band emission peak matching well with the bandgap of the InGaAs cell. Then, we add a BGR on the PV cell to regulate the absorption spectrum of the cell. Results show that, compared to the back surface reflector (BSR), the TPV system with the Au BGR cell has a higher power conversion efficiency (PCE), because more OOB photons are reflected back to the emitter by the Au BGR cell, so that the absorbed power by the cell decreases while the output power is improved. Due to the contribution of recycled OOB photons, at 1500 K, a 1.7 % OOB reflectance gain of the BGR (h = 0.2 μm, t = 1.2 μm) can actually increase the PCE by about 4 %. In addition, a thin PV cell and an appropriately thick air gap layer of 0.4–0.6 μm are suggested to obtain a high η × Pout. The PCE of the TPV system based on the Tamm plasmon emitter is higher and becomes saturated at a lower temperature than the broad-band SiC emitter. This work may facilitate high-performance TPV energy conversion.

Robust Load Frequency Control of Interconnected Power Systems with Back Propagation Neural Network-Proportional-Integral-Derivative-Controlled Wind Power Integration

As the global demand for energy sustainability increases, the scale of wind power integration steadily increases, so the system frequency suffers significant challenges due to the huge fluctuations of the wind power output. To address this issue, this paper proposes a Back Propagation Neural Network-Proportional-Integral-Derivative (BPNN-PID) controller to track the output power of the wind power generation system, which can well alleviate the volatility of the wind power output, resulting in the slighter imbalance with the rated wind power output. Furthermore, at the multi-area power system level, to mitigate the impact of the imbalanced wind power injected into the main grid, the H∞ robust controller was designed to ensure the frequency deviation within the admissible range. Finally, a four-area interconnected power system was employed as the test system, and the results validated the feasibility and effectiveness of both the proposed BPNN-PID controller and the robust controller.

Self-powered piezoelectric sensing system for rotational speed detection of AUV propellers

To realize high-precision self-supplied speed measurement of Autonomous Underwater Vehicle (AUV) propellers, a self-powered piezoelectric speed sensing and detecting system is developed, which consists of a self-powered piezoelectric detection module and energy management and sensing circuits. The system uses three piezoelectric cantilevers for power and sensing detection. The proposed speed detection system is based on the piezoelectric effect and realizes self-powered sensing by utilizing the kinetic energy generated during the rotation of the propeller into electrical energy. The comprehensive model of the proposed piezoelectric sensing system under periodic toggled excitation is established and analyzed. The optimal output power of the system is investigated through theoretical analysis and simulation. The experimental system of the self-powered speed sensing system is constructed and the effect of speed measurement is tested. Experimental results show that the maximum output power of the piezoelectric self-powered sensing system developed in this work is 218 μW, which is much higher than that of the purely triboelectric sensing system. And the average detection error of the self-powered sensing system is 1.4% and the linearity is 1.09% when the propeller speed ranges from 0 to 300 r/min. Compared with similar self-powered systems, the proposed piezoelectric self-powered system is more advantageous in terms of measurement accuracy and can provide more accurate propeller speed measurement.