Power Conversion Efficiency Research Articles

Boosting the Efficiency of Perovskite/Organic Tandem Solar Cells via Enhanced Near-Infrared Absorption and Minimized Energy Losses.

The compatibility of perovskite and organic photovoltaic materials in solution processing provides a significant advantage in the fabrication of high-efficiency perovskite/organic tandem solar cells. However, additional recombination losses can occur during exciton dissociation in organic materials, leading to energy losses in the near-infrared region of tandem devices. Consequently, a ternary organic rear subcell is designed containing two narrow-bandgap non-fullerene acceptors to enhance the absorption of near-infrared light. Simultaneously, a unique diffusion-controlled growth technique is adopted to optimize the morphology of the ternary active layer, thereby improving exciton dissociation efficiency. This innovation not only broadens the absorption range of near-infrared light but also facilitates the generation and effective dissociation of excitons. Owing to these technological improvements, the power conversion efficiency (PCE) of organic solar cells increased to 19.2%. Furthermore, a wide-bandgap perovskite front subcell is integrated with a narrow-bandgap organic rear subcell to develop a perovskite/organic tandem solar cell. Owing to the reduction in near-infrared energy loss, the PCE of this tandem device significantly improved, reaching 24.5%.

Molecular Design Engineering Regulates the Ground-State Passivation Ability of Benzophenone Derivatives in Perovskite Solar Cells.

Intramolecular hydrogen bonding (H-bonding) involved in the excited-state proton transfer (ESPT) process results in benzophenone derivatives (BPDs) with an excellent ability to passivate defects. However, the BPDs are in a continuing dynamic transition process between the ground state and the excited state under light radiation conditions. The ground-state BPDs may lose their ability to passivate defects, resulting in an increased defect density of the perovskite. Therefore, enhancing the passivation ability of the ground-state BPDs can help to achieve the full passivation ability of their ground state to excited state. Herein, we have researched the various BPDs by density functional theory and found that intramolecular H-bonding can weaken the passivation ability of ground-state BPDs, but intramolecular H-bonding is indispensable in the ESPT process. To address the issue, we investigated the influence of electron-donor properties and dipole moments of hydroxyl (-OH), methoxy (-OCH3), and n-octyloxy (-OC8H17) groups in BPD molecules on their coordination capacity through molecular design engineering. Ultimately, 2-hydroxy-4-n-octyloxy-benzophenone (UV5) with strong electron-donor n-octyloxy (-OC8H17) and elongated carbon-chain structure was selected as an additive, which enhances the passivate defect capability in both the ground and excited states. As a result, the UV5-based champion device achieved a power conversion efficiency (PCE) of 24.46% and remained at 75% of the initial PCE with exposure to UV light. This work focuses on the defect passivation capability of ground-state BPDs for the first time and opens a new concept for applying BPDs in PSCs.

Theoretical Optimization of an Earth-Abundant and Environmentally Friendly Photovoltaic Absorber Cu3PSe4 from First-Principles Study to Device Simulation.

To seek an earth-abundant and environmentally friendly absorber for thin-film solar cells, Cu3PSe4 is investigated by first-principles calculations and device simulations. We demonstrate that the compound has a suitable band gap width of 1.3 eV as well as a high sunlight absorption coefficient. However, drawbacks like small electron affinity, high hole concentration, large lattice mismatch with CdS, etc., are revealed, which may degrade the photovoltaic performance. To address those shortcomings, we propose (1) to optimize the carrier concentration by preparing the samples at low temperature and under a Cu-rich environment, (2) to replace the CdS buffer layer by a more suitable wide-gap semiconductor with smaller lattice mismatch, and (3) that the selected buffer layer should have small electron affinity in order to reduce the open-circuit voltage losses. After implementation of these optimization approaches, the device simulations demonstrate that the power conversion efficiency reaches 17.7% for a solar cell with the configuration Mo/Cu3PSe4/WS2/n-ZnO. The combination of first-principles calculations at the atomistic level and device simulations at the macroscopic level provides an appropriate approach to design ideal solar cells.

Theoretical Study of the Strong Piezo-phototronic Effect in 2D Monochalcogenides for Multi-Junction Solar Cells

Abstract The piezophototronic effect is a new scientific area that investigates the synergistic interactions of piezoelectric, semiconductor, and photoexcitation features. This effect is seen in crystals lacking inversion symmetry, where applied strain alters electronic transport and provides a way to modify material properties. Monolayer 2D semiconductors, such as TMDCs and group IV monochalcogenides, have higher piezoelectric coefficients than conventional piezoelectric materials. This study suggests creating a stable and high-performance Multijunction Solar Cell (MJSC) using the piezo-phototronic effect. The emphasis is on single-type 5-layer 2D monochalcogenides such as SnS, SnSe, GeS, and GeSe, which employ band gap engineering. Surprisingly, the ultrathin parallel-connected solar cell achieves an electric power conversion efficiency of over 31% when tested under blackbody radiation, exceeding the recognized S-Q limit. The piezophototronic effect improves solar cell performance while also addressing voltage mismatch issues. This work introduces a novel approach to developing and manufacturing high-efficiency and robust monolithic multijunction photovoltaic solar cells (MJPSC) based on 2D monochalcogenides.

Revealing Defect Passivation and Charge Extraction by Ultrafast Spectroscopy in Perovskite Solar Cells through a Multifunctional Lewis Base Additive Approach

Defect passivation inside the crystal lattice and the grain‐boundary (GB) surface of the perovskite films has become the most effective strategy to suppress the negative impact of the nonradiative recombination in perovskite solar cell. In this study, a unique approach to effectively passivate the defect states of MAPbI3 perovskite thin film using thionicotinamide (TNM) as a multifunctional Lewis base additive is demonstrated. TNM as an additive with three different types of Lewis base sites, i.e., pyridine, amino, and CS functional groups, is introduced to mitigate the trap states in the TNM‐modified perovskite films and thoroughly investigate the passivation defects. The nonbonded electron of the three different Lewis base sites can synergistically passivate the antisite lead (Pb) defects and improve the stability of the device. In addition, the NH2 group can form ionic bonds with negatively charged I– ions and inhibit ion migration caused by them. It is found that such passivation effect of TNM reduces the GB defects and improves the crystallinity significantly. As a result, a champion TNM‐modified device shows an improved power conversion efficiency of 19.26% from 16.86% along with enhanced open‐circuit voltage, fill factor, and negligible hysteresis.

Micronuclear battery based on a coalescent energy transducer.

Micronuclear batteries harness energy from the radioactive decay of radioisotopes to generate electricity on a small scale, typically in the nanowatt or microwatt range1,2. Contrary to chemical batteries, the longevity of a micronuclear battery is tied to the half-life of the used radioisotope, enabling operational lifetimes that can span several decades3. Furthermore, the radioactive decay remains unaffected by environmental factors such as temperature, pressure and magnetic fields, making the micronuclear battery an enduring and reliable power source in scenarios in which conventional batteries prove impractical or challenging to replace4. Common radioisotopes of americium (241Am and 243Am) are α-decay emitters with half-lives longer than hundreds of years. Severe self-adsorption in traditional architectures of micronuclear batteries impedes high-efficiency α-decay energy conversion, making the development of α-radioisotope micronuclear batteries challenging5,6. Here we propose a micronuclear battery architecture that includes a coalescent energy transducer by incorporating 243Am into a luminescent lanthanide coordination polymer. This couples radioisotopes with energy transducers at the molecular level, resulting in an 8,000-fold enhancement in energy conversion efficiency from α decay energy to sustained autoluminescence compared with that of conventional architectures. When implemented in conjunction with a photovoltaic cell that translates autoluminescence into electricity, a new type of radiophotovoltaic micronuclear battery with a total power conversion efficiency of 0.889% and a power per activity of 139 microwatts per curie (μW Ci-1) is obtained.

Estimation of power conversion efficiency up to 12% of nanocomposites of catechin and carboxylated graphene quantum dots doped/functionalised with boron as photosensitizers in DSSC applications

ABSTRACT The power conversion efficiency (PCE) of dye-sensitised solar cells (DSSCs) measures their solar energy conversion performance. With PCEs below 15%, significant energy loss occurs, leading researchers to seek improvements to reduce fossil fuel dependence and enhance DSSCs as an alternative energy source. However, predicting PCE theoretically is challenging due to its dependence on various parameters. In this work, the improved normal model was used to predict the PCE accurately using DFT and TD-DFT of four nanocomposites consisting of catechin natural compound attached to carboxylated graphene quantum dots (GQD) that have been further doped at the centre/edge and decorated with a boronic group. The nanocomposites have been adsorbed on a TiO2 cluster for PCE estimation. This is the first attempt of using decorated GQD with boronic groups in a DSSC and estimating its PCE. The results show that the PCE of catechin improved from 0.077% to the range of 3.96% – 12.61% (B1-CG-C@TiO2 – B2-CG-C@TiO2). This was due to the improved short-circuit current density ( J sc ) and fill factor (FF) of all the nanocomposites and the improved open-circuit voltage ( V oc ) of all nanocomposites except B1-CG-C@TiO2 in comparison to catechin. This means all the designed nanocomposites are more promising candidates than catechin. Highlights Adsorption at carboxyl group is the most stable site among hydroxyl and GQD base. The improved normal model gives accurate V oc results. All designed nanocomposites exhibited higher PCEs than isolated catechin. Edged doping exhibited the highest V oc , high J sc , and highest PCE of 12.61%.

Revealing and Inhibiting the Facet-related Ion Migration forEfficient and Stable Perovskite Solar Cells.

Ion migration is a major issue hindering the long-term stability of perovskite solar cells (PSCs). As an intrinsic characteristic of metal halide perovskite materials, ion migration is closely related to the atomic arrangement and coordination, which are the basic characteristic differences among various facets. Herein, we report the facet-related ion migration, and then achieve the inhibition of ion migration in perovskite through finely modulating the facet orientation. We show that the (100) facet is substantially more vulnerable to cationic migration than the (111) facet. The main reason for this difference in migration is that the cationic migration route in the (111) facet deviates from that in the (100) facet, which increases the active migration energy and weakens the contribution from the electric field during operation. We prepare a (111)-dominated perovskite film by incorporating a facile and green addition of water (H2O) into the antisolvent, further achieving a power conversion efficiency (PCE) of 26.0% (25.4% certification) on regular planar PSCs and 25.8% on inverted PSCs. Moreover, the unencapsulated PSCs can maintain 95% of their initial PCE after 3500-hours operation under simulated AM1.5 illumination at the maximum power point.

Non‐Ionic Perylene‐Diimide Polymer as Universal Cathode Interlayer for Conventional, Inverted, and Blade‐Coated Organic Solar Cells

AbstractAs a class of predominantly used cathode interlayers (CILs) in organic solar cells (OSCs), perylene‐diimide (PDI)‐based polymers exhibit intriguing characteristics of excellent charge transporting capacity and suitable energy levels. Despite that, PDI‐based CILs with satisfied film‐forming ability and adequate solvent resistance are rather rare, which not only limits the further advance of OSC performances but also hinders the practical use of PDI CILs. Herein, we designed and synthesized two non‐conjugated PDI polymers for achieving high power conversion efficiency (PCE) in diverse types of OSCs. The utilization of oligo (ethylene glycol) (OEG) linkage enhanced the n‐doping effect of PDI polymers, leading to an improved ability of the CIL to reduce work function and improve electron transporting capability. Moreover, the introduction of the non‐ionic OEG chain effectively improve the wetting property and solvent resistance of PDI polymers, so the PPDINN CIL can withstand diverse processing conditions in fabricating different OSCs, including conventional, inverted and blade‐coated devices. The binary OSC with conventional structure using PPDINN CIL showed a PCE of 18.6 %, along with an improved device stability. Besides, PPDINN is compatible with the large‐area blade‐coating technique, and a PCE of 16.6 % was achieved in the 1‐cm2 OSC where a blade‐coated PPDINN was used.

Revealing and Inhibiting the Facet‐related Ion Migration for Efficient and Stable Perovskite Solar Cells

Ion migration is a major issue hindering the long‐term stability of perovskite solar cells (PSCs). As an intrinsic characteristic of metal halide perovskite materials, ion migration is closely related to the atomic arrangement and coordination, which are the basic characteristic differences among various facets. Herein, we report the facet‐related ion migration, and then achieve the inhibition of ion migration in perovskite through finely modulating the facet orientation. We show that the (100) facet is substantially more vulnerable to cationic migration than the (111) facet. The main reason for this difference in migration is that the cationic migration route in the (111) facet deviates from that in the (100) facet, which increases the active migration energy and weakens the contribution from the electric field during operation. We prepare a (111)‐dominated perovskite film by incorporating a facile and green addition of water (H2O) into the antisolvent, further achieving a power conversion efficiency (PCE) of 26.0% (25.4% certification) on regular planar PSCs and 25.8% on inverted PSCs. Moreover, the unencapsulated PSCs can maintain 95% of their initial PCE after 3500‐hours operation under simulated AM1.5 illumination at the maximum power point.

Tracing the electron transport behavior in quantum-dot light-emitting diodes via single photon counting technique

The electron injection and transport behavior are of vital importance to the performance of quantum-dot light-emitting diodes. By simultaneously measuring the electroluminescence-photoluminescence of the quantum-dot light-emitting diodes, we identify the presence of leakage electrons which leads to the discrepancy of the electroluminescence and the photoluminescence roll-off. To trace the transport paths of the leakage electrons, a single photon counting technique is developed. This technique enables us to detect the weak photon signals and thus provides a means to visualize the electron transport paths at different voltages. The results show that, the electrons, except those recombining within the quantum-dots, leak to the hole transport layer or recombine at the hole transport layer/quantum-dot interface, thus leading to the reduction of efficiency. By reducing the amount of leakage electrons, quantum-dot light-emitting diode with an internal power conversion efficiency of over 98% can be achieved.

Enhancement of Electron Transport Characteristics Using MXene-MnFeO3 Nanocomposite Integration with Fullerene Derivatives for the Perovskite-Based Solar Cells and Detectors.

In this study, we prepared a hybrid film incorporating the MnFeO3-decorated conducting two-dimensional (2D) MXene sheet-suspended [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) electron transfer layer (ETL) for the perovskite solar cells (PSCs) and detectors. The incorporation of MXene-MnFeO3 with the PCBM ETL could drive exceptional conducting features for the PSCs. Moreover, the presence of MXene-MnFeO3 facilitated superior charge transfer pathways, thereby enhancing the electron extraction and collection processes. This enhancement was directed to improve the electron mobility within the device, resulting in high photocurrents. The designed interface engineering with the MXene-MnFeO3 nanocomposite-tuned PCBM ETL has produced a remarkable power conversion efficiency of 17.79% ± 0.27. Moreover, X-ray detectors employing PCBM modulated with the MXene-MnFeO3 ETL achieved notable performance metrics including 18.47 μA/cm2 CCD-DCD, 5.53 mA/Gy·cm2 sensitivity, 7.64 × 10-4 cm2/V·s electron mobility, and 1.51 × 1015 cm2/V·s trap density.

In Situ Growth of MoS2 Onto Co-Based MOF Derivatives Toward High-Efficiency Quantum Dot-Sensitized Solar Cells.

Quantum dot sensitized solar cells (QDSCs) represent a promising third-generation photovoltaic technology, boasting a high theoretical efficiency of 44% and cost efficiency. However, their practical efficiency is constrained by reduced photovoltage (Voc) and fill factor (FF). One primary reason is the inefficient charge transfer and elevated recombination rates at the counter electrode (CE). In this work, a novel CE composed of a titanium mesh loaded with Co,N─C@MoS2 is introduced for the assembly of QDSCs. The incorporation of nanosized MoS2 enhances the density of catalytic sites, while the Co,N─C component ensures high conductivity and provides a substantial active surface area. Additionally, the titanium mesh's 3D structure serves as an effective electrical conduit, facilitating rapid electron transfer from the external circuit to the composite. These improvements in catalytic activity, charge transfer rate, and stability of the CE significantly enhance the photovoltaic performance of QDSCs. The optimized cells achieve a groundbreaking power conversion efficiency (PCE) of 16.39%, accompanied by a short-circuit current density (Jsc) of 27.26mA cm-2, Voc of 0.818V, and FF of 0.735. These results not only offer a new strategy for designing electrodes with high catalytic activity but also underscore the promising application of the Co,N─C@MoS2 composite in enhancing QDSC technology.

Enhancement of photovoltaic parameters of thermally stable graphene/LaVO3 semitransparent solar cell by employing interfacial graphene quantum dots.

Semitransparent solar cells are attracting attention not only for their visual effects but also for their ability to effectively utilize solar energy. Here, we demonstrate a translucent solar cell composed of bis(trifluoromethane sulfonyl)-amide (TFSA)-doped graphene (Gr), graphene quantum dots (GQDs), and LaVO3. By introducing a GQDs intermediate layer at the TFSA-Gr/LaVO3 interface, we can improve efficiency by preventing carrier recombination and promoting charge collection/separation in the device. As a result, the efficiency of the GQDs-based solar cell was 4.35%, which was higher than the 3.52% of the device without GQDs. Furthermore, the average visible transmittance of the device is 28%, making it suitable for translucent solar cells. The Al reflective mirror-based system improved the power conversion efficiency (PCE) by approximately 7% compared to a device without a mirror. Additionally, the thermal stability of the device remains at 90% even after 2000 h under an environment with a temperature of 60°C and 40% relative humidity. These results suggest that TFSA-Gr/GQDs/LaVO3-based cells have a high potential for practical use as a next-generation translucent solar energy power source.

Enhanced Buried Interface Engineering for Efficient Inverted Perovskite Solar Cells Fabricated via Vapor-Solid Reaction.

Vapor-deposited inverted perovskite solar cells utilizing self-assembled monolayer (SAM) as hole transport material have gained significant attention for their high efficiencies and compatibility with silicon/perovskite monolithic tandem devices. However, as a small molecule, the SAM layer suffers low thermal tolerance in comparison with other metal oxide or polymers, rendering poor efficiency in solar device with high-temperature (> 160°C) fabricating procedures. In this study, a dual modification approach involving AlOx and F-doped phenyltrimethylammonium bromide (F-PTABr) layers is introduced to enhance the buried interface. The AlOx dielectric layer improves the interface contact and prevents the upward diffusion of SAM molecules during the vapor-solid reaction at 170°C, while the F-PTABr layer regulates crystal growth and reduces the interfacial defects. As a result, the AlOx/F-PTABr-treated perovskite film exhibits a homogeneous, pinhole-free morphology with improved crystal quality compared to the control films. This leads to a champion power conversion efficiency of 21.53% for the inverted perovskite solar cells. Moreover, the encapsulated devices maintained 90% of the initial efficiency after 600h of ageing at 85°C in air, demonstrating promising potential for silicon/perovskite tandem application.

3-Methylthiophene: A Sustainable Solvent for High-Performance Organic Solar Cells.

The use of harmful halogenated or aromatic solvents such as chloroform (CF), chlorobenzene (CB), and o-xylene (o-XY) is one of the greatest barriers to the industrial-scale manufacturing of high-performance organic solar cells (OSCs). Therefore, it is necessary to eliminate the effects of these solvents to ensure practical feasibility of OSCs. We found that the anthracene-terminated polymer donor and small-molecule acceptor BO-4Cl had good solubility in 3-methylthiophene (3-MeT). There were no toxicity labels in the SDS and exposure control limits for 3-MeT. An overall power conversion efficiency of 16.87% was achieved by using 3-MeT as the solvent for solar cell fabrication, which was higher than that of the cells made from CF (16.18%) and o-XY (15.69%). The best OSC based on PM6:D18:L8-BO and fabricated with 3-MeT exhibited a high PCE of 18.13%, which is one of the highest values for cells fabricated from halogen-free solvents. These results indicate that 3-MeT is an eco-friendly and low-toxicity solvent for the sustainable fabrication of the OSC active layer.

A Graded Redox Interfacial Modifier for High-Performance Perovskite Solar Cells.

Perovskite solar cells have emerged as a potential competitor to the silicon photovoltaic technology. The most representative perovskite cells employ SnO2 and spiro-OMeTAD as the charge-transport materials. Despite their high efficiencies, perovskite cells with such a configuration show unsatisfactory lifespan, normally attributed to the instability of perovskites and spiro-OMeTAD. Limited attention was paid to the influence of SnO2, an inorganic material, on device stability. Here we show that improving SnO2 with a redox interfacial modifier, cobalt hexammine sulfamate, simultaneously enhances the power-conversion efficiency (PCE) and stability of the perovskite solar cells. Redox reactions between the bivalent cobalt complexes and oxygen lead to the formation of a graded distribution of trivalent and bivalent cobalt complexes across the surface and bulk regions of the SnO2. The trivalent cobalt complex at the top surface of SnO2 raises the concentration of (SO3NH2)- which passivates uncoordinated Pb2+ and relieves tensile stress, facilitating the formation of perovskite with improved crystallinity. Our approach enables perovskite cells with PCEs of up to 24.91%. The devices retained 93.8% of their initial PCEs after 1000 hours of continuous operation under maximum power point tracking. These findings showcase the potential of cobalt complexes as redox interfacial modifiers for high-performance perovskite photovoltaics.

Extending Shelf-life of Two-step Method Precursor Solutions through Targeted Regulation for Highly Efficient and Reproducible Perovskite Solar Cells.

Precursor solution aging process can cause significant influence on the photovoltaic performance of perovskite solar cells (PVSCs). Notably, we first observe that the aging phenomenon is more severe in the precursor of two-step sequential method compared to that in one-step method due to that the protic solvent isopropanol facilitates amine-cation side reaction and iodide ions oxidation. Herein, we report a novel approach for selectively stabilizing both organic amine salt and lead iodide (PbI2) precursor solutions in two-step method. The introduction of benzene-1,3-dithiol into organic amine salt solution can mitigate amine-cation side reactions due to the formation of an acidic and reducing environment. Simultaneously, decamethylferrocene (FcMe10/FcMe+10) pair can act as a redox shuttle in PbI2 solution to concurrently oxidize Pb0 and reduce I2 in cyclic manner. Consequently, the PVSCs device fabricated from ameliorative precursor solutions demonstrates superior power conversion efficiency of 25.31%, retaining 95% of its efficiency after 21 days of solution aging. Moreover, the unencapsulated devices maintain 85% of primitive efficiency for 1500 h at maximum power point tracking under continuous illumination. This work establishes a fundamental guidance and scientific direction for the stabilization of two-step perovskite precursor solutions.

Thickness Optimization of Front and Recombination ITO in Monolithic Perovskite/Silicon Tandem Solar Cells

Optical losses of perovskite/silicon tandem solar cells can be effectively reduced by optimizing the thin‐film layer thicknesses. Herein, the thicknesses of DC sputtered indium tin oxide (ITO) films, which serve as the front electrode and the recombination layer connecting the subcells, are optimized to reach high transparency and good lateral charge transport simultaneously. Optical simulations of the full perovskite/silicon tandem solar cell stacks are performed to find the optimum recombination and front electrode ITO thicknesses for solar cells as well as modules. Implementation of the optimized 25 nm front electrode ITO thickness in semitransparent single‐junction perovskite solar cells increases the short‐circuit density by 1.5 mA cm−2 compared to the former reference thickness of 75 nm. Combined with an optimized 20 nm recombination ITO layer, high short‐circuit density of 20.3 mA cm−2 is reached in perovskite/silicon tandem solar cell devices, which is the highest reported value for planar front perovskite/silicon tandem solar cells to the best of knowledge. Further interface passivation enables 28.8% power conversion efficiency.

A Facile Low Prevacuum Treatment to Enhance the Durability of Nonfullerene Organic Solar Cells

Herein, a straightforward vacuum‐assisted method is introduced to enhance the stability of nonfullerene organic solar cells (OSCs). The method, termed “prevacuum” involves subjecting the active layer (D18:Y6) to a low‐pressure vacuum (−1 bar) before thermal annealing at 100 °C. Compared to untreated devices, prevacuum‐treated OSCs exhibit a notable increase in power conversion efficiency from 13.71% to 14.90%. This enhancement is attributed to improved light absorption and charge extraction, as evidenced by external quantum efficiency measurements. Moreover, prevacuum treatment significantly improves device stability under operational conditions, with a 30% power loss occurring after 8.25 h compared to 4.5 h for untreated devices. This improvement is attributed to the removal of volatile components and impurities during the vacuum process, leading to a more hydrophobic and stable active layer. The study demonstrates the efficacy of prevacuum treatment as a simple and accessible method for enhancing the performance and longevity of OSCs, paving the way for their broader application in sustainable energy technologies.