Potential Membrane Research Articles

Evaluating the efficiency of modified hydrophobic PVDF membrane for the removal of PFOA substances from water by direct contact membrane distillation

This study addresses the global issue of the contamination of water resources by per- and poly-fluoroalkyl substances (PFAS). PFAS are notoriously difficult to remove due to their resilient alkyl-fluorinated chains. We examined the potential of hydrophobic PVDF membranes in direct contact membrane distillation (DCMD) to eliminate perfluorooctanoic acid (PFOA) from Water. For desalination, both commercial and custom-made PVDF membranes exhibited a permeate flux of approximately 13 LMH, with salt rejections of 98.39 % and 99.95 %, respectively. In the case of PFOA removal, the fabricated PVDF membrane outperformed its commercial counterpart. It boasted an initial permeate flux of 16 LMH and a PFAS rejection of 95.8 %, compared to the commercial membrane's 13 LMH and 67.31 %. Furthermore, the custom membrane exhibited superior resistance to fouling, experiencing less flux decline. Employing response surface methodology (RSM), we identified the optimal combination of feed concentration (30 ppm), (60 °C), and flow rate (1.5 LPM) to yield a flux of 9 LMH and a PFOA rejection of 95.41 %. Feed temperature emerged as the most influential factor in DCMD performance. This study offers a novel approach to concentrating and removing emerging contaminants from wastewater and highlights the efficacy of tailored membrane technology in addressing pressing environmental challenges.

Lamellar structured GO-Melamine nanocomposite membranes with varying d-spacing for efficient organic solvent nanofiltration (OSN)

There is a lot of research being done on GO lamellar 2D membranes for separating organic solvents and dyes. These membranes are highly sought-after due to their exceptional characteristics. However, existing challenges include inadequate solvent permeability and limited dye rejection capacity due to swelling of membranes. In this study, we proposed a novel technique that employs low-pressure assisted filtration to fabricate nanocomposite membranes using GO and melamine. Remarkably, these composite membranes exhibited outstanding separation performance for dyes (≥99.06 %) in organic solvents, regardless of their positive or negative charges or when present in mixtures. The optimum GO-M0.02 nanocomposite membrane exhibits impressive organic solvent flux (J), attaining a value as high as 50.8 L/m2h (acetone), which is 6.57 times greater than that of the pure GO membrane. Furthermore, these GO-Melamine nanocomposite membranes showed excellent durability against both common and harsh organic solvents, and the flux of solvents through the GO-M0.02 nanocomposite membrane remained almost unchanged even after being immersed in methanol for up to one week. Additionally, the membrane exhibited consistent solvent flux and rejection rates for methyl green during continuous filtration. These results highlight the exceptional stability and immense potential of GO-melamine nanocomposite membranes for real organic solvent nanofiltration.

Metal-organic framework-intercalated graphene oxide nanofiltration membranes for enhanced treatment of wastewater effluents

Graphene oxide membranes (GO) hold immense potential in the field of water purification. However, when applied directly to real wastewater effluents, pure GO membranes suffer from drawbacks such as fouling sensitivity and limited stability. To address these challenges and unlock the full potential of GO membranes, novel nanocomposite membranes have been developed by the intercalation of GO with nanoparticles of ZIF-8 (a type of zeolitic imidazolate framework). The prepared GO/ZIF-8 (GZ) nanocomposite membranes have exhibited enhanced hydrophilicity and exceptional water purification capabilities. Specifically, the GZ membranes have demonstrated a permeance enhancement of over two-fold when compared to the pristine GO reference membrane. This enhancement is coupled with anti-fouling performance and competitive rejection rates for both salts and organic pollutants. GZ membranes have been effectively employed for the purification by cross-flow filtration of 3 industrial wastewater effluents. They have shown improved separation performance compared to the pristine GO reference membrane, and high stability under cross-flow conditions. The origin of the high performances of the GZ membrane has been clarified using structural and morphological analyses. This work highlights the significant progress made in the field of water treatment using graphene-based membranes.

Nanocomposite ceramic membranes as novel tools for remediation of textile dye waste water – A review of current applications, machine learning based modeling and future perspectives

Textile effluent treatment has gained significant attention due to the carcinogenic effects of the dye pollutants present and their enhanced resistance to degradation. Porous ceramic membranes have gained growing interest for dye remediation due to various unique characteristics, including resistance to fungal invasion, adverse chemical conditions, and high temperature. The current study explores applications of ceramic membrane technology, including membranes like MF, UF, and NF, for dye remediation from textile effluent. The best-performing nanocomposite membranes for eliminating azo dyes from textile effluent and efficiencies achieved are reported as Clay-alumina (99%), yttria-stabilized-zirconia (99%), nano TiO2-bentonite UF (95%), and tight TiO2 UF (100%). Ceramic nanocomposites with TiO2 and Al2O3 active layer NF (99%), Ceramic Hybrid hollow fiber LNF (99.3%). Loose nanofiltration (LNF) ceramic membranes have demonstrated outstanding targeted separation performance for the separation of dyes, making them affirm the effective recoveries and recurrent use of high-value-added constituents amongst all the membrane approaches examined. The potential of ceramic membranes for future research and development, including membrane production and mechanism, are discussed. In addition, the implementation of AI-based methods and Machine learning (ML) algorithms are discussed in relation to predicting membrane filtration performance and fouling tendencies and dye removal processes, maximizing opportunities in this field.

Plasma‐oxidized 2D MXenes subnanochannel membrane for high‐performance osmotic energy conversion

AbstractNanofluidic channels inspired by electric eels open a new era of efficient harvesting of clean blue osmotic energy from salinity gradients. Limited by less charge and weak ion selectivity of the raw material itself, energy conversion through nanofluidic channels is still facing considerable challenges. Here, a facile and efficient strategy to enhance osmotic energy harvesting based on drastically increasing surface charge density of MXenes subnanochannels via oxygen plasma is proposed. This plasma could break Ti–C bonds in the MXenes subnanochannels and effectively facilitate the formation of more Ti–O, C═O, O–OH, and rutile with a stronger negative charge and work function, which leads the surface potential of MXenes membrane to increase from 205 to 430 mV. This significant rise of surface charge endows the MXenes membrane with high cation selectivity, which could make the output power density of the MXenes membrane increase by 248.2%, reaching a high value of 5.92 W m−2 in the artificial sea‐river water system. Furthermore, with the assistance of low‐quality heat at 50°C, the osmotic power is enhanced to an ultrahigh value of 9.68 W m−2, which outperforms those of the state‐of‐the‐art two‐dimensional (2D) nanochannel membranes. This exciting breakthrough demonstrates the enormous potential of the facile plasma‐treated 2D membranes for osmotic energy harvesting.

Porous and Dense Alginate/Chitosan Composite Films Loaded with Simvastatin for Dressing Applications

Alginate is a biocompatible polysaccharide matrix used for bioactive dressings with inherent healing properties. Most alginate dressings are produced as single-layer dressings. This study explores the potential of bilayer membranes to modulate drug release and enhance antimicrobial properties. We used alginate and chitosan loaded with simvastatin, an anti-inflammatory drug. One membrane comprised dense layers of both alginate and chitosan, while the other featured a dense alginate upper layer and a porous chitosan lower layer. The current study introduces a new approach in which a bilayer membrane is modeled instead of creating a polymeric blend between alginate and chitosan. The upper layer of the membrane contains only alginate loaded with simvastatin, while the bottom layer contains only chitosan. Another innovation is the study of the use of a porous lower layer of chitosan. Therefore, the association of these polymers in a bilayer and porous membrane gives advanced therapeutic dressings (with anti-inflammatory and antimicrobial properties intrinsic to the membrane) that are more efficient in the healing of complex wounds. Comprehensive characterization encompassed physicochemical, thermal, morphological, and mechanical properties. Microbiological tests were conducted using chitosan extract, and cytotoxicity evaluations were performed on fibroblast and keratinocyte cells. The results showed interlayer adhesion due to ionic interactions between alginate and chitosan surfaces. The drying process influenced the morphological and physicochemical features of the membranes. Simvastatin release profiles demonstrated sustained release over an extended period (approximately 60%–70% of the drug after 96 h). Storage assessments revealed that after six months, the membranes maintained around 98% of the initial simvastatin content. The antimicrobial activity test underscored the bacteriostatic efficacy of the chitosan porous layer, making it well-suited for infected wounds. Cell viability tests confirmed the non-cytotoxic nature of the films, highlighting their promising characteristics for treating diverse skin lesion types.

Surface characterization and Remazol Red adsorption by asymmetric polyethersulfone membranes modified by polyelectrolyte complexes

AbstractPolyethersulfone (PES) membranes containing 4‐fluorophenyl sulfone‐terminated poly(diallylpiperidinium hexafluorophosphate)‐sulfonated poly(ethylene terephthalate) polyelectrolyte complexes (PECs) were obtained via phase inversion using three different methods that enabled the complexation of polyelectrolytes (PELs) to occur before, after, and during membrane formation. Atomic force microscopy‐infrared spectroscopy analysis revealed varying concentrations of the polyanion depending on the preparation method and confirmed the presence of PECs in the membranes, highlighting an increase in surface roughness. Zeta potential measurements demonstrated positive surface charges for the membrane comprising PES and the polycation. The reduction in zeta potential in PEC membranes corresponded with the neutralization of positive groups by sulfonated poly(ethylene terephthalate. Scanning electron microscopy micrographs depicted surface imperfections in PEC membranes, emphasizing the influence of PECs on membrane surfaces. The water contact angle decreased, indicating increased hydrophilicity in PEC membranes. Additionally, dye adsorption results showcased significant adsorption, with the membranes absorbing at least 60% of Remazol Red from an aqueous solution. Notably, the Blend membrane outperformed others, exhibiting an exceptional adsorption rate exceeding 92%.

Zeolite Imidazolate Frameworks-8@SiO2-ZrO2 Crystal-Amorphous Hybrid Core-Shell Structure as a Building Block for Water Purification Membranes.

Metal-organic frameworks (MOFs) are emerging as promising materials for water purification membranes, owing to their uniform microporous structures and chemical functionalities. Here, we report a simple procedure for depositing MOF-based nanofiltration membranes on commercial TiO2 ceramic tubular supports, completely avoiding the use of dispersants or binders. Zeolite imidazolate frameworks-8 (ZIF-8) nanocrystals were synthesized in methanol at room temperature and subsequently coated with an amorphous SiO2-ZrO2 gel to generate a dispersion of ZIF-8@SiO2-ZrO2 core-shell nanoparticles. The amorphous SiO2-ZrO2 gel served as a binding agent for the ZIF-8 nanocrystals, thus forming a defect-free continuous membrane layer. After repeating the coating twice, the active layer had a thickness of 0.96 μm, presenting a rejection rate >90% for the total organic carbon in an aquaculture effluent and in a wastewater treatment plant, while reducing the concentration of trimethoprim, here used as a target pollutant. Moreover, the oxide gel provided the MOF-based active layer with good adhesion to the support and enhanced its hydrophilicity, resulting in a membrane with excellent mechanical stability and resistance to fouling during the crossflow filtration of the real wastewater samples. These results implied the high potential of the MOF-based nanocomposite membrane for effective treatment of actual wastewater streams.

Identification and anti-oxidative potential of milk fat globule membrane (MFGM)-derived bioactive peptides released through in vitro gastrointestinal digestion

This study investigated the stability of milk fat globule membrane (MFGM) protein under simulated gastrointestinal conditions using an in vitro enzymatic digestion method. The optimal hydrolysis conditions were determined by monitoring the changes in particle size and zeta-potential of MFGM protein hydrolysates over time. Furthermore, the distribution of small molecular weight peptides with antioxidant activity was explored through DEAE-52 combined with in vitro cell experiments. Two novel antioxidant peptides (TGIIT and IITQ) were identified based on molecular docking technology and evaluated their potential scavenging activity against 1,1-diphenyl-2-picrylhydrazyl (DPPH) and 2,2′-Azinobis-(3-ethylbenzthiazoline-6-sulphonate) (ABTS+) radicals. TGIIT and IITQ also demonstrated remarkable abilities in promoting mitochondrial biogenesis and activating Keap1/Nrf2 signaling pathway, which can effectively counteract skeletal muscle dysfunction induced by oxidative stress. Thus, MFGM-derived antioxidant peptides have the potential to be employed in food to regulate muscle protein metabolism and alleviate sarcopenia.

Application of confocal microscopy and flow cytometry to identify physiological responses of Prorocentrum micans to the herbicide glyphosate

The physiological response of the dinoflagellate P. micans to the effect of the herbicide glyphosate at a concentration of 25–200 μg L−1 was evaluated. It has been shown that P. micans is able to grow due to the consumption of dissolved organic phosphorus formed as a result of the mineralization of glyphosate by bacteria. The addition of glyphosate to the medium inhibits the photosynthetic activity of cells; there is a pronounced inhibition of the relative electron transfer rate along the electron transport chain and the maximum quantum efficiency of the use of light energy. Morphological and ultrastructural changes in P. micans cells were evaluated at sublethal (150 μg L−1) and lethal (200 μg L−1) glyphosate concentrations. It has been shown that at a herbicide concentration of 150 μg L−1, the first signs of apoptosis appear in most P. micans cells: a decrease in lateral light scattering, cytoplasmic retraction, partial destruction of cytoplasmic organelles, a change in the morphology of nuclei, mitochondria, a change in the potential of mitochondrial membranes, and a decrease in the autofluorescence of chlorophyll in cells. At a glyphosate concentration of 200 μg L−1, P. micans showed signs of a late stage of apoptosis: violation of the integrity of intracellular organelles and chromatin organization, fragmentation of nuclei, condensation of cytoplasm, disorganization of chloroplasts in the cells, and the release of cell contents beyond the cell membrane. The effectiveness of using flow cytometry and laser scanning confocal microscopy methods for identifying signs and stages of cell apoptosis when exposed to glyphosate is discussed.

Surface Bioengineering of Mo2Ga2C MAX Phase to Develop Blended Loose Nanofiltration Membranes for Textile Wastewater Treatment.

The potential of blended loose nanofiltration membranes (LNMs) to fractionate dyes and inorganic salts in textile wastewater has become a focus of attention in recent years. In this research work, we fabricated LNMs based on polysulfone (PSf) membranes blended with l-histidine amino acid-functionalized Mo2Ga2C MAX phase (His-MAX). Scanning electron microscopy (SEM), atomic force microscopy (AFM), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), contact angle, ζ-potential, porosity, and pore size analyses were employed to characterize the LNMs. Blending 0.75 wt % of His-MAX additive with the PSf tailored the LNM's features by making it more water-friendly, increasing its porosity, enlarging its pores, and making its surface smoother. The pure water flux of 127.6 L/m2 h was achieved by LNM containing 0.75 wt % His-MAX, which was 2.5 times greater than the bare one. The mentioned LNM displayed a flux recovery ratio (FRR) of 68.27 and 98.57, 98.31, and 99.7% rejections for Direct red 23, Acid brown 75, and Reactive blue 21 solutions (100 mg/L), respectively. The 0.75 wt % His-MAX LNM could reject 99.1% of dye and 11.5% of salt while maintaining an FRR of 91.19% after four cycles of filtering a binary mixture solution containing Reactive blue 21 and Na2SO4. These findings highlight the potential of the fabricated LNM for desalinating dye solutions.

Development of Aqueous Organic Flow Battery Using SPEEK Membrane and Eco-Friendly Electrolytes

Aqueous organic redox flow batteries (AORFBs) are a type of flow battery that offers a promising solution for energy storage, and one of the main issues is selecting low-cost membranes with high ion conductivity to enhance performance and efficiency. In this study, low-cost sulfonated poly ether ether ketone (SPEEK) membranes were fabricated using the casting method, with the polymer/solvent ratios of SPEEK and N,N'-dimethylformamide (DMF) being varied. The Nafion 117 membrane was used as a benchmark for comparison. The performance of aqueous organic redox flow batteries employing anthraquinone-2-sulfonic acid (AQS) and 1,2-benzoquinone-3,5-disulfonic acid (BQDS) as electrolytes was evaluated. The SPEEK membranes were determined to have dense, homogeneous surfaces with no flaws and a thickness of 60 microns. In addition, their physicochemical properties, such as water uptake, swelling ratio, ion exchange capacity, and degree of sulfonation, were investigated. The results showed that the SPEEK membranes had better rate performance and cycle stability when compared to the Nafion117 membrane during charge-discharge cycles. Additionally, the SPEEK membranes exhibited slower potential drops and higher power density during constant current mode operation, despite showing no significant differences in energy efficiency and power density. These findings demonstrate the potential of SPEEK membranes for use in AORFBs and as a benchmark for future research and development.

Surface modification of perforated separator for more robust and thinner all‐solid‐state electrolyte membrane

AbstractSolid electrolytes (SEs) play an essential role in the development of all‐solid‐state batteries (ASSBs) due to their exceptional ionic conductivity. However, conventional pelletized SEs with hundreds of micrometers result in highly reduced energy density and suffer from mechanical brittleness, which delay the commercialization of ASSBs. In this study, we present an innovative approach to fabricate SE membranes with perforated Al2O3 nanolayer‐coated polyethylene (PE) separator as a mechanical supporter. Al2O3‐coated separators exhibit better adhesion with LPSCl particles and better thermal stability. As a result, the SE membrane exhibits thickness of 35 μm while maintaining a superior mechanical tensile strength. Furthermore, when the SE membrane is applied to Li||LiNi0.7Co0.15Mn0.15O2 full‐cells, stable cycling performance over 250 cycles, which is comparable to thick LPSCl pellet cell, can be achieved even with higher conductance (>150 mS). Our results highlight the potential of thin and durable SE membranes in contributing to the commercialization of ASSBs.

Adaptive Epidermal Bioelectronics by Highly Breathable and Stretchable Metal Nanowire Bioelectrodes on Electrospun Nanofiber Membrane

AbstractThe potential of the electrospun nanofiber membrane (ENM)‐based soft electronics in epidermal bioelectronics has gained huge attention with their conformal compatibility with the human body and associated performance improvements. This study presents a novel filtration‐based direct local nanowire patterning method on the ENM using dispenser systems, aiming to fabricate stretchable, breathable, and highly conductive epidermal electronics harnessing various types of metal nanowires, including Ag, Ag@Au core–shell, and Ag@(Au–Pt) core–shell nanowires. By utilizing capillary force from a support bed beneath the ENM, efficient fluid flow can be achieved, eliminating the requirement for expensive vacuum equipment typically employed in filtration processes. In the postprocessing phase, the photothermal effect of a laser is harnessed to improve the mechanical stability of the nanowire–ENM interface. The maskless fabrication process is instrumental in crafting epidermal bioelectronics in that the design can be spontaneously replicated according to diverse human body geometries in situ. The selective insulation process can be also executed with the same dispenser system, streamlining the overall fabrication system. Applications are demonstrated showcasing the advantages of the presented fabrication system and the resulting devices, including an in vivo epicardial signal recording electrode, an epidermal electrochemical biosensor, and a customized epidermal electromyography (EMG)‐based human–machine interface (HMI).

Effective potentials in lipid membranes

Effective potentials in lipid membranes

The potential application of cellulose acetate membrane for CO2 adsorbent

ABSTRACT Numerous countries have deployed significant efforts to reduce the amount of CO2 released into the atmosphere. Carbon capture and storage is widely regarded as a mitigation technique that can significantly reduce CO2 emissions. A crucial stage in carbon capture and storage is CO2 adsorption using a membrane. Cellulose acetate has demonstrated excellent properties as a membrane material. In this study, we examined the potential of cellulose acetate membrane (CAM) for CO2 gas capture. Two forms of CAM were developed for this study, with and without the addition of glycerol. Scanning Electron Microscope (SEM), Fourier Transform Infrared (FTIR), and CO2 adsorption analyses were used to characterise CAM in numerous ways. The analysis revealed that the addition of glycerol improved the gas adsorption properties of the material. The incorporation of glycerol into the cellulose acetate matrix resulted in an observed augmentation in both the diameter and pore size. The adsorption properties of CO2 are significantly influenced by the microscopic structure of the cellulose acetate membrane. The CAM can be viewed as a possible material for CO2 adsorbers.

Nanofiltration Ceramic Membranes as a Feasible Two-Pronged Approach toward Desalination and Lithium Recovery.

Ceramic membranes are taking center stage for separation technologies in water treatment. Among them, ceramic nanofiltration membranes are at the forefront of membrane technologies. The desalination of seawater using ceramic nanofiltration membranes is a potential application toward increasing the global water supply and tackling water scarcity. However, while the high fabrication cost poses a challenge to their large-scale applications, high-value separation applications can help to offset the overall cost. In this regard, ceramic nanofiltration membranes can also be explored as a viable option for high-value lithium extraction from the waste seawater brine. In order to determine the potential of nanofiltration ceramic membranes for desalination and lithium recovery from seawater, the current efficiency of salt rejection across various operation parameters must be thoroughly evaluated. Specifically, the interactions between the Donnan exclusion, steric exclusion, zeta potential, and salt concentration play an important role in determining the salt rejection efficiency. Several strategies are then proposed to guide ceramic nanofiltration membranes toward potentially practical applications regarding desalination and lithium recovery.

Ultra-high flux mesh membranes coated with tannic acid-ZIF-8@MXene composites for efficient oil-water separation

Oil/water separation has become a global concern due to the increasing discharge of multi-component harmful oily wastewater. Super wetting membranes have been shown to be an effective material for oil/water separation. Ultra-high flux stainless-steel meshes (SSM) with superhydrophilicity and underwater superoleophobicity were fabricated by tannic acid (TA) modified ZIF-8 nanoparticles (TZIF-8) and two-dimensional MXene materials for oil/water separation. The TZIF-8 increased the interlayer space of MXene, enhancing the flux permeation (69,093 L m−2h−1) and rejection of the composite membrane (TZIF-8@MXene/SSM). The TZIF-8@MXene/SSM membrane showed an underwater oil contact angle of 154.2°. The membrane maintained underwater superoleophobic after stability and durability tests, including various pH solutions, organic solvents, reusability, etc. In addition, the oil/water separation efficiency of TZIF-8@MXene/SSM membranes was higher than 99% after treatment in harsh conditions and recycling. The outstanding anti-fouling, stability, durability, and recyclability properties of TZIF-8@MXene/SSM membrane highlight the remarkable potential of membranes for complex oil/water separation process.

Impact of the hypoxic microenvironment on spermatogonial stem cells in culture.

The stem cell niche plays a crucial role in the decision to either self-renew or differentiate. Recent observations lead to the hypothesis that O2 supply by blood and local O2 tension could be key components of the testicular niche of spermatogonial stem cells (SSCs). In this study, we investigated the impact of different hypoxic conditions (3.5%, 1%, and 0.1% O2 tension) on murine and human SSCs in culture. We observed a deleterious effect of severe hypoxia (1% O2 and 0.1% O2) on the capacity of murine SSCs to form germ cell clusters when plated at low density. Severe effects on SSCs proliferation occur at an O2 tension ≤1% and hypoxia was shown to induce a slight differentiation bias under 1% and 0.1% O2 conditions. Exposure to hypoxia did not appear to change the mitochondrial mass and the potential of membrane of mitochondria in SSCs, but induced the generation of mitochondrial ROS at 3.5% and 1% O2. In 3.5% O2 conditions, the capacity of SSCs to form colonies was maintained at the level of 21% O2 at low cell density, but it was impossible to amplify and maintain stem cell number in high cell density culture. In addition, we observed that 3.5% hypoxia did not improve the maintenance and propagation of human SSCs. Finally, our data tend to show that the transcription factors HIF-1α and HIF-2α are not involved in the SSCs cell autonomous response to hypoxia.

Solvent-free polyamide TFC membrane fabrication based on TMC vaporization for saline water recovery

While thin film composite (TFC) membranes have dominated the global desalination process, using large amounts of organic solvent during membrane manufacturing remains a major concern. Thus, a greener approach to prepare TFC membranes based on solvent-free trimesoyl chloride monomer vaporization is presented in this work. This study fabricated the solvent-free membranes by varying relevant parameters during the vapor interfacial polymerization (VIP) process and studied their impacts on the membrane properties. Evidently, the VIP membranes exhibited thinner polyamide layers than conventionally prepared membrane following the slow polymerization rate. This resulted in higher pure water permeability (2.93 L/m2.h.bar) than the conventional membrane (2.53 L/m2.h.bar) when both membranes were tested at 8 bar. Despite demonstrating slight decrease in salt rejection, the saline water recovery performance of VIP membrane was unaffected, as high salt rejection was unnecessary. Under the best synthesis conditions, a VIP membrane with lower salt rejection could rival the conventional membrane with a >98 % dye rejection while attaining substantially higher NaCl/dye selectivity (up to 330) than the conventional ones (68.75). Pertinently, the study findings demonstrated the potential of the solvent-free IP-fabricated TFC membrane for saline water recovery.