Posterior Femoral Rollback Research Articles

In Vivo Normal Knee Kinematics: Is Ethnicity or Gender an Influencing Factor?

In vivo studies have suggested Caucasians achieve lower average knee flexion than non-Western populations. Some previous studies have also suggested gender may influence condylar AP translation and axial rotation, while others report an absence of such an influence. We determined whether different ethnic and gender groups residing in the United States had different knee translations and rotations. Three-dimensional knee rotations and translations were determined for 72 healthy subjects (24 Caucasian men, 24 Caucasian women, 13 Japanese men, 11 Japanese women) from full extension to maximum flexion using a fluoroscopic technique, under in vivo, weightbearing conditions. Although we observed substantial variability in all groups, small differences between groups were found, especially in deep flexion. Japanese women and men and Caucasian women achieved higher maximum flexion (153°, 151°, and 152°, respectively) than Caucasian men (146°). External rotation was higher for these three groups than for Caucasian men. The medial condyle remained more anterior for Caucasian women and all Japanese subjects than for Caucasian men, possibly leading to greater axial rotation and flexion, observed for these three groups. We identified small differences in maximum flexion between genders and ethnic groups. While no differences were identified in the lateral condyle translation, the medial condyle remained more stationary and more anterior for the groups that achieved highest (and similar) maximum flexion. Therefore, it may be important for future implant designs to incorporate these characteristics, such that only the lateral condyle experiences greater posterior femoral rollback, while the medial condyle remains more stationary throughout flexion.

Correlation between preoperative and postoperative knee kinematics in total knee arthroplasty using cruciate retaining designs

The authors evaluated the relationships between preoperative and postoperative kinematics in 50 osteoarthritic knees scheduled for cruciate retaining total knee arthroplasty with regards to posterior femoral roll back and external femoral rotation using a navigation system from 10° to 120° of knee flexion. Although posterior femoral roll back was maintained, external femoral rotation was significantly decreased compared to those of the preoperative knee after total knee arthroplasty. However, the amount of posterior roll back and external femoral rotation after total knee arthroplasty were found to be significantly positively related to those measured preoperatively (r = 0.62 and 0.57, respectively). These significant kinematic correlations may explain why preoperative range of knee motion influences range of motion after total knee arthroplasty.

The effect of geometry of the tibial polyethylene insert on the tibiofemoral contact kinematics in Advance Medial Pivot total knee arthroplasty

BackgroundIn modern total knee arthroplasty (TKA), it is important to reproduce both medial pivot motion and posterior femoral rollback to obtain greater postoperative knee flexion. Several studies have reported the factors affecting knee motion and range of motion after TKA. The purpose of this study was to evaluate the effect of the tibial insert geometry on the tibiofemoral contact kinematics, especially focusing on the medial pivot motion and posterior femoral rollback. MethodsSeven cadaveric knees were replaced with the Advance Medial Pivot TKA, and two different geometries of polyethylene tibial insert, the standard medial pivot design (MP-design) and double high design (DH-design), were biomechanically compared. Four experimental configurations were evaluated in each specimen in this order: (1) the MP-design with posterior cruciate ligament (PCL) retaining, (2) the DH-design with PCL retaining, (3) the MP-design with PCL sacrificing, and (4) the DH-design with PCL sacrificing. ResultsUnder the PCL-retaining condition, both designs showed no medial pivot but bicondylar femoral rollback more than 60° of knee flexion. In the MP-design, tibiofemoral contact point (estimated contact point, ECP) of the medial compartment was located on the posterior lip of the ball-insocket structure while demonstrating greater than 120° of knee flexion. The posterior translation was also the same in both designs. On the other hand, ECP of the MP-design and the DH-design showed only medial pivot pattern under the PCL-sacrificing condition. In the DH-design, ECP of the lateral compartment showed paradoxical anterior translation from 0° to 60° of knee flexion. Total posterior translation was significantly greater in the lateral compartment than that in the medial compartment. ConclusionsThe results of this study suggest that in this type of TKA system the ball-in-socket geometry in the MP-design has an advantage for reproducing medial pivot motion in the PCL-sacrificing condition, and the flexion path structure in the DH-design is considered to be both effective and safe for femoral rollback in the PCL-retaining condition. However, neither design is sufficient to reproduce medial pivot motion and posterior femoral rollback. Therefore, a different design of tibial insert is needed for more physiological kinematics after TKA.

In Vivo Kinematics after a Cruciate-substituting TKA

Patterns of motion in the native knee show substantial variability. Guided motion prosthetic designs offer stability but may limit natural variability. To assess these limits, we therefore determined the in vivo kinematic patterns for patients having a cruciate-substituting TKA of one design and determined the intersurgeon variability associated with a guided-motion prosthetic design. Three-dimensional femorotibial contact positions were evaluated for 86 TKAs in 80 subjects from three different surgeons using fluoroscopy during a weightbearing deep knee bend. The average posterior femoral rollback of the medial and lateral condyles for all TKAs from full extension to maximum flexion was -14.0 mm and -23.0 mm, respectively. The average axial tibiofemoral rotation from full extension to maximum flexion for all TKAs was 10.8 degrees. The average weightbearing range of motion (ROM) was 109 degrees (range, 60 degrees-150 degrees; standard deviation, 18.7 degrees). Overall, the TKA showed axial rotation patterns similar to those of the normal knee, although less in magnitude. Surgeon-to-surgeon comparison revealed dissimilarities, showing the surgical technique and soft tissue handling influence kinematics in a guided-motion prosthetic design. Level III, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

In Vivo Determination of Kinematics for Subjects Having a Zimmer Unicompartmental High Flex Knee System

The objective of this study was to determine the in vivo kinematics during weight-bearing and non–weight-bearing activities for subjects with a unicompartmental knee arthroplasty (UKA) designed for high flexion and implanted with minimally invasive techniques. A total of 30 UKAs implanted in 18 patients were analyzed. All patients were implanted with a medial Zimmer Unicompartmental High Flex Knee System (Zimmer Inc, Warsaw, Ind). Under fluoroscopic surveillance, each patient performed weight-bearing deep knee bend, normal gait, and passive flexion. The kinematics of the medial UKA was determined using a 3-dimensional model registration technique. On average, the implant experienced posterior femoral rollback and normal axial rotation during flexion. However, the kinematic patterns for each patient were not consistent, and the variability was high during flexion and stance phase of gait.

In Vivo Comparison of Knee Kinematics for Subjects Having Either a Posterior Stabilized or Cruciate Retaining High-Flexion Total Knee Arthroplasty

The objective of this study was to determine the in vivo kinematics for subjects having either a fixed posterior stabilized (PS) or cruciate retaining (CR) high-flexion total knee arthroplasty (TKA). Three-dimensional kinematics from full extension to maximum flexion were determined for 30 subjects (15 PS, 15 CR) using fluoroscopy. On average, the PS subjects demonstrated 112° of weight-bearing (WB) flexion, −6.4 mm of posterior femoral rollback, and 2.9° of axial rotation. The CR subjects averaged 117° of WB flexion, −4.9 mm of posterior femoral rollback, and 4.8° of axial rotation. Posterior femoral rollback of the lateral condyle occurred for all PS TKAs and in 93% of the CR TKAs. Only 2 subjects in each group experienced greater than 1.0 mm of condylar lift-off. Subjects in both TKA groups demonstrated excellent WB ranges of motion and kinematic patterns similar to the normal knee, but less in magnitude.

Posterior condylar offset and flexion in posterior cruciate-retaining and posterior stabilized TKA

BackgroundAnterior tibial translation associated with posterior impingement has been reported to be one of the factors limiting flexion after posterior cruciate-retaining (CR) total knee arthroplasty (TKA), especially when posterior condylar offset is decreased postoperatively. On the other hand, its effect on postoperative motion in posterior-stabilized (PS) TKA remains unknown. It has been demonstrated that PS TKA exhibits a consistent posterior femoral rollback during flexion. Thus, we hypothesized that the problem of posterior impingement can be avoided by use of PS TKA. In this study, we examined the relationship between postoperative posterior condylar offset and knee flexion in CR and PS TKAs. MethodsIn this study, analysis was performed for 20 subjects who underwent bilateral TKAs (one CR and one PS TKA) as well as another group of 50 PS TKAs. All patients could be tracked for a minimum of 2 years. The range of flexion was measured before operation and at follow-up. Preoperative and postoperative posterior condylar offset was evaluated on true lateral radiographs. ResultsAt the follow-up examination, the mean flexion angle was 123° in the CR knees and 131° in the PS knees with a significantly greater improvement observed for the latter group. In the roentgenographic measurement of the posterior condylar offset, no significant difference was observed between the preoperative and postoperative values both in the CR and PS knees. We divided the patients into two groups according to the change of posterior condylar offset. The first group (Group I) showed a decrease in the posterior condylar offset after surgery and the second group (Group II) showed no change or an increase. Subsequently, postoperative change in flexion was compared between Groups I and II for the CR and PS knees. A significant difference between Groups I and II was observed in the CR knees, while no difference was observed in the PS knees. The magnitude of postoperative posterior condylar offset did not correlate with an improvement in maximum flexion angle in the 50 PS knees. ConclusionsIt was shown that the magnitude of posterior condylar offset correlated with a postoperative change in flexion angle in CR knees, while no such correlation was observed in PS knees.

Kinematic analysis of kneeling in cruciate‐retaining and posterior‐stabilized total knee arthroplasties

Kneeling is an important function of the knee for many activities of daily living. In this study, we evaluated the in vivo kinematics of kneeling after total knee arthroplasty (TKA) using radiographic based image-matching techniques. Kneeling from 90 to 120 degrees of knee flexion produced a posterior femoral rollback after both cruciate-retaining and posterior-stabilized TKA. It could be assumed that the posterior cruciate ligament and the post-cam mechanism were functioning. The posterior-stabilized TKA design had contact regions located far posterior on the tibial insert in comparison to the cruciate-retaining TKA. Specifically, the lateral femoral condyle in posterior-stabilized TKA translated to the posterior edge of the tibial surface, although there was no finding of subluxation. After posterior-stabilized TKA, the contact position of the post-cam translated to the posterior medial corner of the post with external rotation of the femoral component. Because edge loading can induce accelerated polyethylene wear, the configuration of the post-cam mechanism should be designed to provide a larger contact area when the femoral component rotates.

In Vivo Determination of Total Knee Arthroplasty Kinematics: A Multicenter Analysis of an Asymmetrical Posterior Cruciate Retaining Total Knee Arthroplasty

The objective of this study was to determine if consistent posterior femoral rollback of an asymmetrical posterior cruciate retaining (PCR) total knee arthroplasty was mostly influenced by the implant design, surgical technique, or presence of a well-functioning posterior cruciate ligament (PCL). Three-dimensional femorotibial kinematics was determined for 80 subjects implanted by 3 surgeons, and each subject was evaluated under fluoroscopic surveillance during a deep knee bend. All subjects in this present study having an intact PCL had a well-functioning PCR knee and experienced normal kinematic patterns, although less in magnitude than the normal knee. In addition, a surprising finding was that, on average, subjects without a PCL still achieved posterior femoral rollback from full extension to maximum knee flexion. The findings in this study revealed that implant design did contribute to the normal kinematics demonstrated by subjects having this asymmetrical PCR total knee arthroplasty.

Effect of knee laxity on in vivo kinematics of meniscal-bearing knee prostheses

Introduction This study determined the relationship between the in vivo kinematics and joint laxity of mobile-bearing knees. Materials and methods Ten subjects who were judged clinically successful after a posterior-cruciate-ligament-retaining mobile-bearing total knee arthroplasty were analyzed under dynamic conditions using fluoroscopy, following a quantitative evaluation of coronal and sagittal laxity using Telos and KT-2000 arthrometers under static conditions. Results Under static conditions, the anteroposterior laxity averaged 10.3 mm at 30° of flexion, and 8.3 mm at 75°. Abduction and adduction at full extension averaged 3.7 and 4.4 mm, respectively. Under dynamic conditions, 7/10 subjects demonstrated posterior femoral rollback of their lateral condyle moving from full extension to maximum knee flexion, and 8/10 experienced normal axial rotation patterns during deep knee bend activity. Furthermore, 7/10 subjects exhibited screw-home motion. 4/10 subjects experienced greater than 1.0 mm of condylar liftoff. Conclusion We could not predict a consistent relationship between the laxity and kinematics. The activity of the muscles and ligamentous tension under dynamic conditions might have a much greater effect on the kinematics with currently used prosthetic designs than the laxity of ligamentous structures under static conditions.

Physiologic Kinematics as a Concept for Better Flexion in TKA

Functional outcome after total knee arthroplasty is determined by strength, stability and range of motion. Flexion in the replaced knee is suboptimal for many patients and kinematics after total knee arthroplasty is abnormal. The relation between kinematics of the replaced knee and postoperative flexion is analyzed and compared to normal knee kinematics. Specific characteristics that relate to better flexion are defined: posterior condylar offset, femoral roll-back and femoral external rotation. The rationale for a guided motion knee arthroplasty is developed and positioned within the current state of the art knowledge on total knee arthroplasty.

In Vivo Kinematic Comparison of Posterior Cruciate-Retaining and Posterior Stabilized Total Knee Arthroplasties Under Passive and Weight-Bearing Conditions

An in vivo comparison of flexion kinematics for posterior cruciate-retaining (PCR) and posterior stabilized (PS) total knee arthroplasty (TKA) was performed. Twenty patients who underwent bilateral paired TKAs were included in this prospective study. Both PCR and PS prostheses were from the same TKA series with comparable surface geometries, and all were implanted by a single surgeon. Of these 20 patients, 3-dimensional kinematics during flexion could be analyzed using a computer model fitting technique in 18 patients. The follow-up period ranged from 18 to 53 months. In the PCR TKA, an anterior femoral translation from 30° to 60° of flexion was observed in the weight-bearing condition. In contrast, flexion kinematics for the PS TKA was characterized by the maintenance of a constant contact position under weight-bearing conditions and posterior femoral rollback in passive flexion.

A High Flexion Total Knee Arthroplasty Design Replicates Healthy Knee Motion

Deep flexion affects both femorotibial contact pattern and the patellofemoral articulation. The purpose of this study was to compare the patellofemoral motion of nonimplanted and implanted knees and to analyze femorotibial kinematics after total knee replacement designed for deep flexion. Three-dimensional patellofemoral kinematics were evaluated during a deep knee bend using fluoroscopy for five control patients with a healthy knee, five patients with an anterior-cruciate-ligament-deficient knee, and 20 patients who had a high flexion total knee arthroplasty. Less translation of patellofemoral contact position was seen in patients who had knee replacements than in patients with healthy knees, but the average motion and the patella tilt angles were similar to the healthy knees. On average, patients who had a total knee arthroplasty had 4.9 degrees normal axial rotation, and all patients had at least -4.4 mm of posterior femoral rollback. The average weightbearing range of motion of the patients in the total knee arthroplasty group was 125 degrees . In this study, patients implanted with a high-flexion knee replacement design had kinematic patterns that were similar to the healthy knee. It can be hypothesized that forces acting on the patella were not substantially increased for patients who had a total knee arthroplasty compared with the control patients.

In vivo kinematic evaluation and design considerations related to high flexion in total knee arthroplasty

In designing a posterior-stabilized total knee arthroplasty (TKA) it is preferable that when the cam engages the tibial spine the contact point of the cam move down the tibial spine. This provides greater stability in flexion by creating a greater jump distance and reduces the stress on the tibial spine. In order to eliminate edge loading of the femoral component on the posterior tibial articular surface, the posterior femoral condyles need to be extended. This provides an ideal femoral contact with the tibial articular surface during high flexion angles. To reduce extensor mechanism impingement in deep flexion, the anterior margin of the tibial articular component should be recessed. This provides clearance for the patella and patella tendon. An in vivo kinematic analysis that determined three dimensional motions of the femorotibial joint was performed during a deep knee bend using fluoroscopy for 20 subjects having a TKA designed for deep flexion. The average weight-bearing range-of-motion was 125°. On average, TKA subjects experienced 4.9° of normal axial rotation and all subjects experienced at least −4.4 mm of posterior femoral rollback. It is assumed that femorotibial kinematics can play a major role in patellofemoral kinematics. In this study, subjects implanted with a high-flexion TKA design experienced kinematic patterns that were similar to the normal knee. It can be hypothesized that forces acting on the patella were not substantially increased for TKA subjects compared with the normal subjects.

In vivo fluoroscopic analysis of fixed-bearing total knee replacements.

In vivo kinematic patterns were determined for subjects (patients participating in the study), having either a fixed-bearing posterior-stabilized or posterior cruciate-retaining total knee arthroplasty. While under fluoroscopic surveillance, subjects did normal gait and a deep knee bend. Video images were downloaded to a workstation computer and analyzed in three dimensions using an iterative model-fitting approach. Femorotibial contact paths for the medial and lateral condyles, axial rotation, and condylar lift-off were determined. During a deep knee bend, subjects having a posterior-stabilized total knee arthroplasty routinely experienced posterior femoral rollback of their lateral condyle and normal axial rotational patterns, whereas random subjects having a posterior cruciate-retaining total knee arthroplasty experienced paradoxical anterior sliding and opposite axial rotational patterns. During gait, posterior-stabilized and posterior cruciate-retaining total knee arthroplasties experienced similar kinematic patterns, with the presence of paradoxical sliding and opposite axial rotational patterns. Subjects having posterior-stabilized and posterior cruciate-retaining total knee arthroplasties experienced condylar lift-off. Subjects having a posterior cruciate-retaining total knee arthroplasty predominantly experienced lateral condylar lift-off whereas subjects with posterior-stabilized total knee arthroplasties experienced either medial or lateral condylar lift-off. Subjects having a posterior-stabilized total knee arthroplasty experienced significantly greater weightbearing range of motion.

In vivo determination of posterior femoral rollback for subjects having a NexGen posterior cruciate–retaining total knee arthroplasty

This study determines the in vivo kinematics during a deep-knee bend activity for subjects implanted with a posterior cruciate–retaining total knee arthroplasty having asymmetric geometries. Of 20 subjects, 19 experienced posterior femoral rollback (PFR) of the lateral condyle (average −3.9 mm), and 13 subjects experienced PFR of the medial condyle (average −3.1 mm). As a result of the lateral condyle rolling further posterior than the medial condyle, on average, subjects experienced 1.4° of normal axial rotation. Of 20 subjects, 10 experienced normal axial rotation, whereas 10 experienced an opposite rotation pattern. Condylar lift-off occurred predominantly with the lateral condyle. Contrary to previous in vivo studies, the subjects in this study experienced consistent PFR of the posterior cruciate–retaining total knee arthroplasty. It can be hypothesized that having asymmetric femoral condyles may lead to PFR with increasing knee flexion. Copyright 2002, Elsevier Science (USA). All rights reserved.

In vivo determination of knee kinematics for subjects implanted with a unicompartmental arthroplasty

Femorotibial contact positions for 20 subjects implanted with a unicompartmental knee arthroplasty (UKA) were analyzed using videofluoroscopy. Femorotibial contact paths were determined using a computer-automated model-fitting technique. Subjects having a medial UKA experienced on average −0.8 mm of posterior femoral rollback, whereas subjects having a lateral UKA experienced −2.5 mm of posterior femoral rollback. Twelve of 17 subjects having a medial UKA and 2 of 3 subjects having a lateral UKA experienced normal axial rotation (average, 3.3° and 11.2°). The results for some subjects suggest that the anterior cruciate ligament was unable to thrust the femur anteriorly at full extension. These results support the findings that the anterior cruciate ligament plays a significant role in knee kinematics, which may contribute to UKA longevity. Copyright 2002, Elsevier Science (USA). All rights reserved.

Observations of femoral rollback in cruciate-retaining knee arthroplasty.

The current study evaluated kinematics of the knee during a stair-climbing activity after total knee arthroplasty. All patients received a posterior cruciate ligament retaining prosthesis of the same design, having an anatomically shaped femoral component and an unconstrained tibial insert. All patients had the same surgical technique done by two experienced surgeons. Patients had some posterior femoral rollback and screw-home type axial rotations during weightbearing activities. However, patients treated by different surgeons had different patterns of tibiofemoral motions. In Group 1, rollback occurred early in the flexion range and was maintained until 80 degrees flexion. In Group 2, the lateral condyle had rollback in early flexion, but both condyles translated forward as flexion increased to 80 degrees. An anatomic femoral component seems to be necessary to produce consistent early femoral rollback. However, soft tissue balance can have a significant effect on the kinematics of sagittally unconstrained posterior cruciate retaining total knee arthroplasty, because it may vary among surgeons.

Kinematic comparison of posterior cruciate sacrifice versus substitution in a mobile bearing total knee arthroplasty

Interest in mobile bearing total knee arthroplasty (TKA) has increased significantly. The objective of this in vivo study was to analyze 2 different mobile bearing TKAs during gait and during a knee bend from 0° to 90° flexion. Femorotibial contact positions for 10 subjects, implanted by a single surgeon, were analyzed using videofluoroscopy. Five subjects were implanted with a posterior-stabilized mobile bearing TKA (PS), and 5 subjects were implanted with a posterior cruciate–sacrificing mobile bearing TKA (PCS). Each subject, while under fluoroscopic surveillance, performed 2 weight-bearing activities: i) normal gait and ii) deep-knee bend. This study showed that the kinematic patterns for subjects having either a PS or PCS mobile bearing TKA were similar during gait but different during a deep-knee bend. Subjects having a PS TKA experienced more posterior femoral rollback of the lateral condyle during the deep-knee bend. Findings of kinematic similarities in gait and differences in a deep-knee bend between these 2 mobile bearing designs are similar to previously published findings of fixed bearing posterior cruciate–retaining and PS TKA. Copyright 2002, Elsevier Science (USA). All rights reserved.

In Vivo Three-Dimensional Knee Kinematics Using a Biplanar Image-Matching Technique

A biplanar image-matching technique was developed and applied to a study of normal knee kinematics in vivo under weightbearing conditions. Three-dimensional knee models of six volunteers were constructed using computed tomography. Projection images of the models were fitted onto anteroposterior and lateral radiographs of the knees at hyperextension and every 15 degrees from 0 degrees to 120 degrees flexion. Knee motion was reconstructed on the computer. The femur showed a medial pivoting motion relative to the tibia during knee flexion, and the average range of external rotation associated with flexion was 29.1 degrees . The center of the medial femoral condyle translated 3.8 mm anteriorly, whereas the center of the lateral femoral condyle translated 17.8 mm posteriorly. This rotational motion, with a medially offset center, could be interpreted as a screw home motion of the knee around the tibial knee axis and a posterior femoral rollback in the sagittal plane. However, the motion of the contact point differed from that of the center of the femoral condyle when the knee flexion angle was less than 30 degrees. Within this range, medial and lateral contact points translated posteriorly, and a posterior femoral rollback occurred. This biplanar image-matching technique is useful for investigating knee kinematics in vivo.